Operating Instruction and Parts Manual for 350/600 Movable Pedestal WARNING DO NOT ATTEMPT TO START OR OPERATE THE MACHINE UNTIL ALL THE INSTRUCTIONS HAVE BEEN READ AND UNDERSTOOD BY THE OPERATOR.
SHOULD YOU REQUIRE ANY SET-UP OR OPERATING ASSISTANCE WITH YOUR PRODUCT, DO NOT RETURN TO ORIGINAL PLACE OF PURCHASE 2 •After referring to the operation manual, if assistance is still needed, please consult our web Site at www.kushlanproducts.
Mixer Instructions 3 A. LUBRICATION: There are grease fittings on all models. Apply any type of EP grease until grease begins to come out of the bearings. LUBRICATE ALL FITTINGS BEFORE EACH USE B. GEARBOX MOTOR: Mixer shipped with lubricate/oil in gearbox. Change lubricate/oil every 200 hours. Use Synthetic Mobile 1 LS 75W-90 oil. C. EXTENSION CORD: Use only out door approved, 14 gauge or larger, grounded extension cords. D. GENERAL: Check all screws for tight ness before each use. E.
Model 350 MP Parts List Item Part Number 1 2 3 4 5 6 7 8 9 10 11 12 13 15 16 17 18 19 350MP-02 350MP-20 350MP-12 350MP-15 350MP-05 350DD-15 350MP-07 350MP-08 350MP-09 350MP-10 350MP-11 350MP-12 350MP-13 350MP-14 350MP-16 350MP-17 350MP-18 350MP-17 DESCRIPTION 350 Drum Blades Hex Head Cap Screw Gear Mounting Base 3/4 HP Gear Motor R Clip Pin Drum Handle Side Handle Bolt Pivot Axle Pin Draw Bar Inside Drum Plate w/ Straight Bushings PU Foam Wheel 1” Washer Main Frame Swivel Bracket 5/16” Nut Whizlock Scre
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Model 350WSB & 350WSB With Stand PartsList List Gearbox and Motor Assembly Parts Part Number DD-808 DDMA-02 DDMA-03 DDMA-04 DDMA-05 DDMA-06 DDMA-07 DDMA-08 DDMA-09 DDMA-10 DDMA-11 DDMA-12 DDMA-13 DDMA-14 DDMA-15 DDMA-16 DDMA-17 DDMA-18 DDMA-19 DDMA-20 DDMA-21 DDMA-22 DDMA-23 DDMA-24 DDMA-25 DDMA-26 DDMA-27 DDMA-28 DDMA-29 DDMA-30 DDMA-31 DDMA-32 DDMA-33 DDMA-34 DDMA
Gearbox and Motor Assembly Parts List 6
Assembly Instruction Step 1 Install Wheels on Lower Frame Unit Step 2 Put on Washer and Snap on R-clip. Step 5 Step 6 Put in Bolt to Hold Main Frame to Draw Take off the Four Outside Nuts and Bar. Spring Washer. Step 9 Install Gear Motor with the Nuts and Washers. They were removed before 7 Step 3 Insert Draw Bar into Main Frame. Step 4 Put on Swivel Bracket to Main Frame. Step 7 Check Inside Nut, so They are Tight. Step 8 Connect Gear Motor Mounting Base to Swivel Bracket Using the Pivot Pin.
Assembly Instruction 8 Step. 1 Main Frame Place the main frame (A) on a level surface. Insert the draw bar (B) into the main frame. Secure with the 76.2 mm hex head bolt and nut (C) on top (A), and the looking bolt (D) to the side (B). (Use the open wrench provided). Wheels - Slide the wheels onto the main frame bar and secure with cotter pins. Step. 2 Gearbox & Motor Assembly Fit the gearbox motor assembly and mounting frame (A) into the swivel bracket (B) with the pivot axle (C).
Assembly Instruction Step. 3 Mounting the Mixing Drum Step.
Transporting the Mixer Operation 10 Disconnect the power cord. Hold the support leg and dump handle and move as shown below. Make sure there is no material in the drum 1. Position the mixer on a level surface. (NOTE: Maximum slope is 5 degrees. Before filling the drum, make sure the mixer can empty into a wheel barrow). 2. Use a 3 prong, grounded, 110V/120V power connection. Although the minimum gauges are listed below, we recommend that a 14 gauge(AWG) wire be used for all lengths.
Kushlan Products Limited Warranty Policy Kushlan Products makes every effort to assure that its products meet high quality and durability standards and warrants to the original retail consumer purchaser of our products (you) that each such product be free from defects in materials and workmanship as follows: ONE(1)YEAR limited warranty on motors. This warranty covers replacement of parts found to be defective in material or workmanship for a period of 90 days from the date of purchase.
