ADVENTURE -MANUAL- 1
TABLE OF CONTENTS Introduction 3 Included In The Box 4 Features And Specs 5 Assembly 6 Safe Riding 12 Charging Battery 13 How To Use The Bike Controls 14 A. Gears B. LCD Display C. Turning the Bike On and Off D. Pedal Assist E. Speedometer F. Walk Mode G. Turning on the Front LED Headlight and Rear LED Light H. Battery Indicator I. Showing the Mileage J. Error Codes K.
INTRODUCTION Congratulations on your new Jetson Adventure! The Adventure is an innovative and fun personal transportation device, ready to take on everyday use. Before your first ride, check whether the wheels are damaged, or parts are loose. If there are any abnormalities, please contact Jetson Customer Support at +1-(888) 976-9904 or email us at customerservice@jetsonbike.com. This product manual can help you understand, use, and maintain your Adventure.
INCLUDED IN THE BOX 3 4 9 6 2 10 7 8 1 11 5 12 16 14 15 17 1. Front Fork with Hydraulic 10. Rear LED Light 3. Handlebar 12. Seat Tube 2. 4. 5. 6. 7. 8. 9. 4 13 Front LED Headlight Handlebar Stem Frame Charging Port Controller Saddle Post Saddle 11. 13. 14. 15. 16. 17.
3 1 9 4 2 8 7 6 1. Left Brake Lever 3. LCD Display 2. 4. 5. 6. 7. 8. 9. 5 Power and Mode Button Right Brake Lever Right Shifter (7 Gears) Left Shifter (3 Gears) Down Button Up Button USB FEATURES AND SPECS MODEL: ADVENTURE WHEEL DIAMETER: 27.5” MOTOR: 250w MPH CHARGER: 110-240V BATTERY TYPE: PANASONIC LITHIUM ION PRODUCT WEIGHT: 42 LBS MAX SPEED: US: 20 MPH UK/EUROPE: 15.5 MOTOR RATED RPM: 195 MAX RANGE: 30-35 MILES BATTERY RATED VOLTAGE: 36v/ 7.
ASSEMBLY The Adventure comes partially assembled. In order to fully assemble, you will need to attach the Handlebars, the Front Wheel, the Disc Brake, the Saddle, and the Pedals. Please refer to the diagrams on pages 4 and 5 while assembling your Adventure. If you are having difficulty assembling the Adventure, please call our customer service or take your Adventure to a local bike shop. Assembling the Handlebar • First, make sure the Handlebar Stem is facing forward, towards the Front Fork.
• Place the Handlebar into the Handlebar Stem and screw the 4 bolts in using the provided Allen Key. Please be careful not to scratch the LCD Screen. • In order to center the Handlebar, make sure the ridge markings are covered by the Handlebar Stem. Connect Wires by Color • Make sure all the wires are connected according to color.
Assembling Disc Brake • Attach the Disc Brake to the Front Fork by screwing in the two bolts. Bolts ATTACHING THE FRONT WHEEL • Twist the cap off the Quick Release Clamping Lever and remove it from the Wheel. • Place the Quick Release Clamping Lever to the side.
Lever Cap • Slide the front Tire between the Front Fork. • Hook the Front Fork onto each side of the Tire and slide the Disc Brake into the Disc. •Please be careful not to bend the Disc Brake. If you find that it will not go in smoothly, please call us for assistance or bring the Adventure to your local bike shop. • Now that the front Tire is fit to the Front Fork, slide the Quick Release Clamping Lever through the Front Wheel.
• Make sure the Quick Release Clamping Lever is secure. Push Lever in • Make sure the Brake is hooked onto the Disc and working properly.
ASSEMBLING PEDALS • There are 2 Pedals. Please look at the inside of each Pedal and see which is labeled R (right) and L (left). • To connect the Pedals to the bike, place L into the Left tube and R into the Right tube (left and right directions are as though you are sitting on the bike). Tighten by turning the Pedals toward the Front Wheel. Use a wrench to make sure the Pedals are tight and secure.
ATTACHING THE SADDLE • Slide the Saddle Post into the Saddle Tube. • Align the Saddle with the Frame to make sure it is straight. • Tighten the Saddle Clamping Lever. • The height of the Saddle should not be pulled higher than the safety tick marks on the Saddle Post. ADJUSTING THE POSITION OF THE LCD DISPLAY To adjust the position of the LCD Display, loosen the bolts that connect the LCD Display to the Handlebars using the provided Allen key.
CHARGING THE BATTERY Your Adventure comes with a built-in rechargeable lithium battery. Always use the provided charger only. Before your first ride you must fully charge the Adventure - charge for 12 hours for the first 3 times you use it. The Charging Port is located on the left side of the frame near the Handlebar Stem (see digram on P. 4 for reference). For every ride after, charge your Adventure until it is fully charged, and NOT LONGER.
HOW TO USE THE BIKE CONTROLS Be cautious as you become accustomed to the Adventure. There are 9 levels of Pedal Assist. The Pedal Assist should be set at 0 when you’re first getting on the Adventure. GEARS The Adventure is a 21-speed e-bike. There are 3 gears in the front and 7 in the rear – change gears by using the Shifters on the handlebar. Only shift gears when pedaling. These gears do not require battery power, and if the battery runs out, you can still use these gears.
The Pedal Assist mode provides power and propels the bike as you pedal. A low Pedal Assist level (1-3) will require effort from you to pedal, a medium Pedal Assist level (4-6) will require some effort from you to pedal, and a high Pedal Assist level (7-9) will require minimal effort from you. To increase the Pedal Assist, press the Up Button. To decrease the Pedal Assist, press the Down Button. Always start off slowly and gradually increase your level.
TURNING ON THE FRONT LED HEADLIGHT AND REAR LED LIGHT Front LED Headlight: Press and hold the Up Button to turn on the Front LED Headlight and the LCD Display Backlight. When the Front LED Headlight and LCD Display Backlight are on, you will see a headlight symbol on the LCD Display. Rear LED Light: There is a button on top of the Rear LED Light to turn it on and off. Please Note: The Front LED Headlight and LCD Backlight are connected to the battery of the bike.
SHOWING THE MILEAGE Press the Power Button (M) to cycle through the mile indicator in the following order: ERROR CODES If there is an error with the function of the bike an error message will be displayed on the LCD Display along with an error code. See the table below for error code definitions.
USB PORT The LCD Display has a USB Port so you can connect and charge your phone. If you are not using the USB Port, please cover it. SETTINGS To access the settings menu, hold the Up and Down Buttons simultaneously for three seconds. Then press the Power Button (M) to scroll through the following settings (The options will appear in the bottom right corner of the LCD Display) Step 1. Choose between the Imperial (mph) and Metric (km/h) system by pressing the Up and Down Buttons.
CLEANING THE ADVENTURE To clean the Adventure carefully wipe with a damp cloth, then dry with a dry cloth. Do not use water to clean the Adventure, as the electrical and electronic systems may get wet, resulting in personal injury or malfunction of the bicycle. Lube the chain every so often to keep it smooth. BATTERY • Keep the bike away from fire and excessive heat. • To avoid damage to the battery, never subject the Adventure to intense physical shock, severe vibration, or impact.
• Be alert to things in front and far away from you. • Make sure your feet are always placed securely on the pedals. • The Adventure cannot be ridden by two or more people. Only one person can ride at a time. • When you ride the Adventure along with other cyclists, always keep a safe distance to avoid a collision. • When turning, be sure to maintain your balance. • Do not allow distractions when riding, such as answering the phone or engaging in any other activities.
LIMITED 1 YEAR WARRANTY TO QUALIFY FOR WARRANTY SERVICE: 1. You must present a copy of the sales receipt from an approved retail partner. 2. This product cannot be used for rental or commercial use. 3. This product cannot be used for competition. LIMITATIONS OF LIABILITY • This Limited 1 Year Warranty is non-transferable after the product’s initial sale. • No unapproved modifications can be made to the product, its performance or otherwise, in order for this Limited 1 Year Warranty to remain in effect.
PRODUCT REGISTRATION Please complete and mail this card within 10 days of purchase or go to https://www.ridejetson.com/product-registration.
ADVENTURE
