Warranty

ManualsBrandsJET ManualsTools & Hardware2 Ton Arbor Press

Operating Instructions and Parts Manual

Arbor Press – ½-, 1-, 2-, 3-, 5-Ton

Model No. AP0-M, AP1-M, AP2-M, AP3-M, AP5-M

WALTER MEIER (Manufacturing) Inc.

427 New Sanford Road

LaVergne, Tennessee 37086

Part No. M-333605M

h.: 800-274-6848 Revision A 05/2011

Summary of content (8 pages)

PAGE 1
Operating Instructions and Parts Manual Arbor Press – ½-, 1-, 2-, 3-, 5-Ton Model No. AP0-M, AP1-M, AP2-M, AP3-M, AP5-M WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph.: 800-274-6848 www.waltermeier.com Part No. M-333605M Revision A 05/2011 Copyright © 2011 Walter Meier (Manufacturing) Inc.
PAGE 2
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. For the name of an Authorized Service Center in your area call 1-800-2746848.
PAGE 3
Table of Contents Warranty and Service .................................................................................................................................... 2 Table of Contents .......................................................................................................................................... 3 Warnings ....................................................................................................................................................... 4 Introduction....
PAGE 4
Warnings 1. Read and understand the entire owners' manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This arbor press is designed and intended for use by properly trained and experienced personnel only.
PAGE 5
Introduction The arbor press is designed for riveting, swaging, bending, punching, and flattening. The arbor press can be used to press on or remove close-fitting bearings and bushings. It is suited for the production environment as well as machine shops, automobile repair shops, and home workshops. The anvil has four slots that are available for a variety of pressing operations. Specifications Stock# ............................... 333605............... 333610............... 333620............... 333630.
PAGE 6
Changing Ram Position Arbor Press Features The ram has a flat surface on one end and a hole on the other end. The hole is used to accept the punch inserts. Change-out the ram as follows: The arbor press (see Exploded view on page 8) consists of a cast iron base, an anvil, a pressing handle with lock knob, and a rack-type ram. The removable anvil has four cutouts that can be used for pressing off or pressing on bearings or bushings of various sizes. A. Remove the handle by loosening the knob (17).
PAGE 7
9 ..........TS-1490051 .....Bolt, Hex M8x30 ......... 2 10 ........TS-1490051 .....Bolt, Hex M8x30 ......... 2 11 ........TS-1540061 .....Nut, Hex M8 ............... 4 12 ........AP2-12 .............Plate........................... 1 13 ........TS-1523011 .....SHSS M6x6................ 1 14 ........AP2-10 .............Pinion Retainer ........... 1 15 ........TS-1490021 .....Bolt, Hex M8x16 ......... 1 16 ........AP2-03 .............Pinion ......................... 1 17 ........AP2-05 .............Knob .....
PAGE 8
Exploded View WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Ph: 800-274-6848 www.waltermeier.