FLUSH MOUNT INSTALLATION MANUAL
CONTeNTS DISCLAIMeR RATINGS MARKINGS CHeCKLIST 1. ATTACH BASeS 2. PLACe RAILS 3. SeCURe LUGS 4. SeCURe MODULeS eXPANSION JOINTS eLeCTRICAL DIAGRAM FLASHFOOT eND CAPS WIRe CLIPS FLUSH STANDOFFS MICROINVeRTeR KITS SYSTeMS USING eNPHASe MICROINVeRTeRS FRAMeLeSS MODULe KITS MODULe COMPATIBILITY WARRANTY 1 2 2 3 4 4 5 5 6 6 7 7 7 7 8 8 8 9 10 DISCLAIMeR This manual describes the proper installation procedures and provides minimum standards required for product reliability and warranty.
RATINGS UL 2703 LISTeD #5003288 #5003320 #5004376 • Conforms to ANSI/UL 2703 (2015) Standard for Safety First Edition: Mounting Systems, Mounting Devices, Clamping/ Retention Devices, and Ground Lugs for Use with Flat-Plate Photovoltaic Modules and Panels • • • • Max Overcurrent Protective Device (OCPD) Rating: 25A Max Module Size: 24ft² Module Orientation: Portrait or Landscape Mechanical Load Rating: meets minimum requirements of the standard (10 PSF downward, 5 PSF upward, 5 PSF lateral).
CHeCKLIST PRe-INSTALLATION IRONRIDGe COMPONeNTS ☐ Verify module compatibility. See Page 9 for info.
1. ATTACH BASeS Install roof attachments. Mount Slotted L-Feet on FlashFoot or other compatible roof attachments per manufacturer's instructions. í IronRidge's all-in-one FlashFoot roof attachment is for pitched, composition shingle roofs. Refer to Page 7 or provided manual. í Tested or evaluated third-party roof attachments: • Anchor Products - U-Anchor • S-5! Standing Seam Metal Roof Clamps - Certification of metal roof clamps includes bonding to both painted and galvalume metal roofs.
3. SeCURe LUGS Insert T-bolt in top rail slot and torque hex nut to 80 inlbs. Install a minimum 10 AWG solid copper or stranded grounding wire. Torque terminal screw to 20 in-lbs. Terminal Screw (20 in-lbs) í Grounding Lugs are only needed on one rail per row of modules (unless frameless modules are being used, see Page 8). í If using enphase microinverters, Grounding Lugs may not be needed. See Page 8 for more information.
eXPANSION JOINTS GROUNDING STRAP eXPANSION JOINT Grounding Strap Expansion Joints are required for thermal expansion of rows exceeding 100 feet of rail. 3/8" From End Torque to 80 in-lbs Insert Internal Splice into first rail and secure with screw. Assemble and secure Grounding Strap 3/8" from rail end. Slide second rail over Internal Splice leaving 1" gap between rails. Attach other end of Grounding Strap with hardware, and torque hex nuts to 80 in-lbs.
FLASHFOOT Locate roof rafters and mark locations on roof. Drill 1/4” pilot holes and backfill with approved sealant. Slide flashing between 1st and 2nd course of shingles ensuring flashing doesn't overhang the downhill shingle. Line up pilot hole and insert supplied 5/16 x 4.5" stainless steel lag bolt through washer, L-Foot, and flashing. Fully seat lag bolt. í L-Foot can face either upslope or downslope on roof. eND CAPS End Caps add a completed look and keep debris and pests from collecting inside rail.
MICROINVeRTeR KITS Use IronRidge's Microinverter Kit to bond compatible microinverters and power optimizers to the racking system. Insert Microinverter Kit T-bolt into top rail slot. Place compatible microinverter or power optimizer into position and tighten hex nut to 80 in-lbs.
MODULe COMPATIBILITY The Flush Mount System may be used to ground and/or mount a PV module complying with UL 1703 only when the specific module has been evaluated for grounding and/or mounting in compliance with the included instructions. Unless otherwise noted, “xxx” refers to the module power rating and both black and silver frames are included in the certification.
WARRANTY Effective for Products manufactured after April 1st, 2012, IronRidge provides the following warranties, for Products installed properly and used for the purpose for which the Products are designed: (a) Products with finishes (ie excluding without limitation Products that are mill finished) shall be free of visible defects, peeling, or cracking, under normal atmospheric conditions, for a period of three years from the earlier of (i) the date of complete installation of the Product or (ii) 30 days af
