www.HunterFan.com Table of Contents Tools Needed Mounting Options Ceiling Bracket 30 inches Blades 3 Downrod Wiring To register your fan, please visit: www.HunterFan.com/register Maintenance & Cleaning ? 15 ? ? 16 PA G E 1 M3585-01 • 11/20/15 • © 2015 Hunter Fan Company 11 Troubleshooting PA G E PA G E 12 Save your receipt for proof of purchase.
www.HunterFan.com What to Expect with Your Installation Read and Save These Instructions If you are unfamiliar with wiring, use a qualified electrician. This product conforms to UL Standard 507. WARNINGS 30 inches from blade tip to nearest wall or obstruction Must be able to secure the fan to building structure or fan-rated outlet box Know your wiring Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.
www.HunterFan.com Tools Needed Ladder Allen Wrench (included) Pliers Wire Strippers 9/64” Drill Bit (optional) Power Drill (optional) If mounting to a support structure, you will also need these tools. 3 M3585-01 • 11/20/15 • © 2015 Hunter Fan Company Screwdrivers 1.888.830.
34O CEILING www.HunterFan.com Mounting Options OPTION 1 If you have a flat ceiling: 1. You will need a longer downrod (sold separately). 2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).
www.HunterFan.com Ceiling Bracket 1.888.830.1326 r we o nP r Tu OFF For angled ceilings, point opening toward peak. Use wood screws Use machine screws (included) when securing (provided with outlet to support structure with box) when securing to approved electrical outlet existing ceiling fan-rated box. Drill 9/64” pilot holes outlet box. Make sure in support structure to aid it is securely installed in securing ceiling bracket and is acceptable for fan with hardware found in support of 31.
Blades www.HunterFan.com Using the included Allen wrench, secure each blade to a blade iron as shown using the blade nuts, found in the hardware bag, and the blade assembly screws, found in the hardware bag. 6 M3585-01 • 11/20/15 • © 2015 Hunter Fan Company 1.888.830.
www.HunterFan.com Option 1 Downrod 1.888.830.
www.HunterFan.com KEEP! (not to scale) 8” & 3/8” 1.888.830.1326 STRIP CUT Downrod (continued) ! KEEP Remove the pre-installed setscrew so that the downrod can be inserted. The wires can be cut, but leave at least 8” extending from the top of the downrod. Hand tighten the downrod (at least 4-5 full turns) until it stops. 8” Tighten the setscrew with pliers. DO NOT HAND TIGHTEN. 3/8” If the setscrew is not tightened securely, the fan may fall.
www.HunterFan.com Downrod (continued) Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan. DO NOT PICK THE FAN UP BY THE CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket. 9 M3585-01 • 11/20/15 • © 2015 Hunter Fan Company 1.888.830.
Wiring OM FR CEILIN www.HunterFan.com Note: To connect the wires, hold the bare metal leads together and place a wire connector over them, then twist clockwise until tight. G OM FR T KE Black FR (Ungrounded) M FA N Blue FRO (Ungrounded) AC Blue ING BR Black CEIL White M Using the orange wire connectors from the hardware bag, connect the black wire (ungrounded) from the ceiling to the black and the blue wires from the fan.
www.HunterFan.com Canopy Screw Holes Position the canopy so that, when lifted into place, the canopy fits into the hanging bracket as shown. Lift the canopy into place so that the screw holes are aligned. Insert the two canopy screws found in the hardware bag. Note: Fan style may vary. 11 M3585-01 • 11/20/15 • © 2015 Hunter Fan Company 1.888.830.
Switch Housing & Light Kit Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter which two screw holes you choose. www.HunterFan.com Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and twist counterclockwise. Note: The decorative cover is not shown in the illustrations. 12 M3585-01 • 11/20/15 • © 2015 Hunter Fan Company 1.888.830.
www.HunterFan.com Switch Housing & Light Kit (continued) 1.888.830.1326 Switch Housing Screw Install the three switch housing assembly screws found in the hardware bag. Tighten all three screws securely. Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors. 13 M3585-01 • 11/20/15 • © 2015 Hunter Fan Company Make sure the light kit assembly is securely attached to the upper switch housing.
www.HunterFan.com Switch Housing & Light Kit (continued) 1.888.830.1326 Metal Plate Globe Globe Keeper CONGRA T YOU’REULATIONS! DONE! Finial Cap Finial Install a bulb into each of the sockets. When necessary, replace with bulbs of the same wattage. Press the globe and globe keeper flush against the metal plate. Thread the light pull chain through the hole in the center of the finial cap and thread the fan pull chain through the hole in the side of the cap.
Maintenance & Cleaning r we o nP www.HunterFan.com 1.888.830.1326 Metal Plate r Tu ON Globe Globe Keeper Finial Cap Finial Changing the bulbs - unscrew the finial and remove it from the threaded rod. Remove the finial cap and unscrew the globe keeper while supporting the globe with your other hand. Carefully remove the globe. Unscrew bulbs and replace with bulbs of same type and wattage. Reinstall the globe assembly.
www.HunterFan.com Troubleshooting Fan doesn’t work Excessive wobbling Noisy Operation • Make sure power switch is on. • Tighten all of the blade and blade iron screws until they are snug. • Tighten the blade and blade iron screws until they are snug. • Pull the pull chain to make sure it is on. • Push the motor reversing switch firmly left or right to ensure that it is engaged. • Check the circuit breaker to ensure the power is turned on. • Make sure the blades spin freely.
