QLogic QMH2462 4GB FC PCI-e Mezzanine Card

Mezzanine Card
Installation Instructions
for supported HP BladeSystem c-Class server blades
Overview
Use these instructions to install optional mezzanine cards.
Optional mezzanine cards are classified as Type I mezzanine
cards and Type II mezzanine cards. The type of the
mezzanine card determines where it can be installed in the
server blade.
Install Type I mezzanine cards on Mezzanine 1 connector,
Mezzanine 2 connector, or Mezzanine 3 connector.
Install Type II mezzanine cards on either Mezzanine 2
connector or Mezzanine 3 connector.
Warnings and cautions
WARNING: To reduce the risk of personal injury
from hot surfaces, allow the drives and the internal
system components to cool before touching them.
WARNING: Reduce the risk of electric shock by
removing all AC power from the system before
installing or replacing an
y non-hot-plug hardware
option. Disconnect all power cords to completely
remove power from the server.
CAUTION:
Electrostatic discharge (ESD) can
damage electronic components. Be sure that you are
properly grounded (earthed) before beginning any
installation procedure.
CAUTION:
Limit the number of times that a
mezzanine card is installed and removed within its
lifecycle to prevent connector pin damage.
Removing the access panel
1. Identify the proper server blade in the enclosure.
2. Back up all server blade data.
3. Power down the server blade.
4. Remove the server blade.
5. Lift the access panel latch and slide the access panel to
the rear.
6. Remove the access panel.
Installing the mezzanine card
IMPORTANT:
Remove the mezzanine card
connector protective cover, if installed.
1. Install the mezzanine card as shown below.
Or, for half-height server
blades install as shown.
2. Reinstall the access panel.
NOTE:
See the HP BladeSystem Enclosure Setup an
d
Installation Guide
for more information on the
association between the mezzanine bay and the
interconnect bays. Where you install the mezzanine
card will determine where you need to install the
interconnect modules.
3. Restore the server blade to its operating position in the
server blade enclosure.
NOTE:
By default, the server blade will power up on
installation.
Completing the installation
For information about installing and configuring drivers for
your specific operating system and mezzanine card refer to
the HP website
(http://www.hp.com/go/bladesystem/mezzanines
).
European Union regulatory
notice
This product complies with the following EU Directives:
• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
Compliance with these directives implies conformity to
applicable harmonized European standards (European
Norms) which are listed on the EU Declaration of Conformity
issued by Hewlett-Packard for th
is product or product family.
This compliance is indicated
by the following conformity
marking placed on the product:
This marking is valid for no
n-Telecom products and EU
harmonized Telecom products (e.g. Bluetooth).
This marking is valid for
EU non-harmonized Telecom
products.
*Notified body number (used only if applicable—refer to the
product label)
Hewlett-Packard GmbH, HQ-TRE,
Herrenberger Strasse 140,
71034 Boeblingen, Germany
Korean class A notice
© Copyright 2006 - 2007 Hewlett-Packard Development
Company, L.P.
The information contained herein is subject to chan
ge without notice. The
only warranties for HP products and services are set fo
rth in the express
warranty statements accompanying su
ch products and services. Nothing
herein should be construed as constituting an additional warranty. H
P shall
not be liable for technical or editorial errors or omissions co
ntained herein.
April 2007 (Second Edition)
Part Number 413773-022
Printed in the US
413773- 022