ENGLISH HKTS 7 Home Theater Speaker System OWNER’S MANUAL
Table of Contents 3 Introduction 4 SUB-TS7 Subwoofer Amplifier Panel Controls and Connections 6 Speaker Placement 7 Mounting Options 8 Speaker Connections 8 Speaker-Level Connection Guide 9 Dolby Digital or DTS (or Other Digital Surround Mode) Connection 10 Dolby Pro Logic (Non-Digital) – Line Level 11 Dolby Pro Logic (Non-Digital) – Speaker Level 12 Operation 12 Volume 12 Additional Bass Adjustments Declaration of Conformity We, Harman Consumer Group, Inc.
Introduction Thank you for purchasing the Harman Kardon HKTS 7, with which you’re about to begin many years of listening enjoyment. The HKTS 7 has been custom-designed to provide all the excitement and power of the cinema experience in your own living room. While sophisticated electronics and state-of-theart speaker components are hard at work within the HKTS 7, hookup and operation are simple. Color-keyed cables and connections, and simple controls make the HKTS 7 easy to use.
Rear Panel Connections 7 HKTS 7 or HKTS 7BQ System Subwoofer-Level Control High-Cut (Low-Pass) Filter Switch Trigger Input Phase Switch Line-Level Subwoofer (SUB) Input Line-Level Full-Range Inputs Speaker-Level Outputs Speaker-Level Inputs Master Power Switch AC Power Cord Subwoofer-Level Control: Volume may be adjusted using the Subwoofer-Level Control. Turn the control clockwise to increase the SUB-TS7’s volume, or counterclockwise to decrease it.
Line-Level Subwoofer (SUB) Input: Connect the subwoofer output of a receiver with digital surround sound decoding, such as Dolby* Digital or DTS®, to this input. This input bypasses the SUB-TS7’s internal crossover circuitry, and should only be used with a filtered signal. If your receiver does not have digital decoding, you should use the Line-Level Full-Range Inputs instead.
Speaker Placement Color-Coding System Center Channel Speaker The HKTS 7 uses the channel color-coding system established by the Consumer Electronics Association to make setting up your home theater speaker system as easy as possible. Your system includes a set of colored stickers that may be placed near the speaker terminals of each of the four satellite speakers according to the key below. It doesn’t matter which satellite speaker is used for any of the front or rear positions.
Wall-Mounting for Satellites Unscrew the bolt that attaches the black shelf stand to the bottom of the speaker. Store the stand and bolt in a safe place in case they are needed for a future installation. The bracket has two openings on top: a round screw hole, and an arc-shaped opening in front of it. The speaker cable should be threaded through the arc-shaped opening, not the screw hole.
Speaker Connections Speaker-Level Connection Guide IMPORTANT NOTE: Before making speaker connections, be certain that your receiver or audio power amplifier is turned off and preferably unplugged from its AC power source. The SUB-TS7 subwoofer should not be connected to an AC power source until all speaker wire connections have been made. Speakers and electronics terminals have corresponding (+) and (–) terminals.
Dolby Digital or DTS® (or Other Digital Surround Mode) Connection Use this installation method for Dolby Digital, DTS® or other digital surround processors: Make sure that you have configured your surround-sound processor for “Subwoofer On.” The front left, front right, center and rear speakers should all be set to “Small.” jack to the LFE output or subwoofer output on your receiver or amplifier. Connect each speaker to the corresponding speaker terminals on your receiver or amplifier.
Speaker Connections Dolby Pro Logic (Non-Digital) – Line Level Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS® or other digital processing), where the receiver/processor is equipped with a subwoofer output, or a volume-controlled preamp (line-) level output: Use RCA-type patch cords to connect the linelevel subwoofer output on your receiver or to amplifier either the left or right line-level input on the subwoofer.
Dolby* Pro Logic* (Non-Digital) – Speaker Level Use this installation method for Dolby Pro Logic applications (not Dolby Digital, DTS® or other digital processing), where the receiver/processor does not have a subwoofer output, or a volumecontrolled preamp (line-) level output: Connect your receiver or amplifier’s front left and right speaker terminals to the left and right terminals on the subwoofer that are marked “High Level In.
Operation Move the Master Power switch (marked “Power” ) to the “•” (On) position to use the subwoofer. The SUB-TS7 subwoofer will automatically turn itself on or go into standby mode depending on whether or not a signal is being sent to it by your receiver or surround processor, and provided that the Trigger On/Off Switch is moved down so that it is in the "AUTO" position.
If there is no sound from any of the speakers: • Check that receiver/amplifier is on and a source is playing. • Check that the powered subwoofer is plugged in, its Power switch is switched on to the “ON •” position. • Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured. • Review proper operation of your receiver/amplifier.
Specifications HKTS 7 System CEN-TS7 Center SUB-TS7 Subwoofer Frequency Response 35Hz – 20kHz (–6dB) Recommended Power 10 – 80 Watts Amplifier 100 Watts RMS Impedance 8 Ohms nominal Bass 10" Woofer, bass-reflex enclosure Sensitivity 86dB @ 1 Watt/1 meter Dimensions (H x W x D) 479mm x 340mm x 340mm Tweeter One 3/4" dome, video-shielded Weight 15kg SAT-TS7 Satellites Recommended Power 10 – 80 Watts Impedance 8 Ohms nominal Sensitivity 86dB @ 1 Watt/1 meter Tweeter One 1/2" dome, video-shielded Mi
ENGLISH
250 Crossways Park Drive, Woodbury, New York 11797 www.harmankardon.com Harman Consumer Group, Inc.
