INSPECTION CAMERA 2.4” lcd 66550 Set up and Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. Save this manual. Copyright© 2008 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally.
NOTICE is used to address practices not related to personal injury. Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 3. Personal safety a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
5. Battery tool use and care a. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack. b. Use the Camera only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. c.
cause cancer, and birth defects or other reproductive harm. Wash hands after handling. (California Health & Safety Code § 25249.5, et seq.) 12. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. 13. This device complies with part 15 of the FCC Rules.
Specifications including HVAC inspection, automotive/ boat/aircraft inspection, cable routing, etc. CAMERA Total Pixels 704x576 (PAL); 712x486 (NTSC) Modulation Type FM Bandwidth 18MHz Power Supply 4 AA batteries To prevent injury from accidental operation: Turn the Power Switch on the Control Handle and Monitor to “OFF” position and unplug the Adaptor from its electrical outlet before performing any adjustments, inspection, maintenance, or cleaning procedures. MONITOR LCD Screen Type 2.
b. Slide knurled knob on Control Handle up to threaded section on Camera cable and finger tighten to secure Camera cable in place. 3. 4. 5. Work Piece and Work Area Set Up 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent injury and distraction. 2. When recharging the Monitor, keep the Monitor close to the Adaptor so that the cord does not present a tripping hazard.
power light on top of Control Handle will be lit. Use this dial to adjust the brightness of LEDs near Camera. 3. Slide ON/OFF switch on right side of Monitor (3) to “ON” position. Press the POWER button on Monitor. Power Light on Monitor will be green and Monitor will display live camera image. Power Light Power Button Orientation Control Brightness Control To Use With T.V. or Monitor The Inspection Camera may be used with a T.V.
Maintenance And Servicing Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent injury from accidental operation: Turn the Power Switch of the Monitor to its “OFF” position and unplug the adaptor from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. To prevent injury from tool failure: Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use. 1.
Troubleshooting Problem Tool will not start. 1. 2. 1. 2. Monitor will not charge. Image too dark or light. Possible Causes Monitor not charged. Batteries need changing. Cable not attached properly. Adapter not connected to power. 1. LEDs near camera need adjustment. 2. Monitor display needs adjustment. Likely Solutions 1. Charge Monitor. 2. Replace batteries in Control Handle. 1. Make sure Adapter Cable is connected between Monitor and Adapter. 2.
Parts List Part 1 2 3 4 5 6 7 8 9 Description Control Handle Mini Camera with Cable Monitor Hook Magnet Mirror Adapter Cable Adapter Extension Cable Qty. 1 1 1 1 1 1 1 1 1 ASSEMBLY DIAGRAM 1 2 8 6 5 4 9 3 7 Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
