ITEM #1461036 OAKHAM CEILING FAN MODEL #42074 Spanish p. 21 Harbor Breeze® is a registered trademark of LF, LLC. All Rights Reserved. ATTACH YOUR RECEIPT HERE Purchase Date _________________________ Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Sunday.
TABLE OF CONTENTS Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Hardware Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Preparation . . . . . . . . . . . . . . . . .
PACKAGE CONTENTS D Q R A E C B F H J G I L K M 2H + S N T + O P PART A B C D E F G H I J K L M N O P Q R S T DESCRIPTION Downrod Downrod Pin (preassembled to Downrod [A]) Downrod Clip (preassembled to Downrod [A]) Mounting Bracket (preassembled to Canopy [E]) Canopy Canopy Cover (preassembled to Canopy [E]) Light Kit Motor Assembly Adapter Plate (preassembled to Motor Assembly [H]) Yoke Cover Blade Arm Blade Glass Bowl Light Pan Bulb Remote Pack Set Screw (preassembled to Motor Assem
HARDWARE CONTENTS (shown actual size) AA Wire Connector Qty. 3 + 1 extra BB Blade Screw Qty. 15 + 1 extra CC Blade Washer Qty. 15 + 1 extra 4 XX Motor Screw Qty.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. • Before you begin installing the fan, disconnect the power by removing fuses or turning off the circuit breakers. • Make sure that all electrical connections comply with local codes, ordinances, the National Electrical Code, and ANSI/NFPA 70-199. Hire a qualified electrician or consult a do-it-yourself wiring handbook if you are unfamiliar with installing electrical wiring.
SAFETY INFORMATION CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present. CAUTION: Carefully check all screws, bolts and nuts on the fan motor assembly to ensure they are secured. CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
INITIAL INSTALLATION 1. Turn off the circuit breakers and the wall switch to the fan supply line leads. 1 DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death. 2. Determine the mounting method to use. Standard mounting is best suited for ceilings 8 ft. or higher. For taller ceilings you may want to use a longer downrod (not included). Angle-style mounting is best suited for angled or vaulted ceilings.
INITIAL INSTALLATION 4. Loosen all four preassembled mounting bracket screws (R), then completely remove the two mounting bracket screws (R) from the round holes of canopy (E). Set aside for later use. 4 Detach mounting bracket (D) from canopy (E). D R E 5. Attach mounting bracket (D) to outlet box (not included) using screws and washers provided with the outlet box. CAUTION: It is very important you use the proper hardware when installing the mounting bracket (D) as this will support the fan.
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 1. Remove the downrod clip (C) and downrod pin (B) from the downrod (A). Then partially loosen the set screws (Q) in the yoke at the top of the motor housing (H). 1 A C Q B H 2. Insert the downrod (A) through the canopy (E) and yoke cover (J). Thread the wires from the motor assembly (H) through the downrod (A). 2 A E J H 3.
STANDARD OR ANGLE MOUNTING INSTRUCTIONS 4. Depending on the length of downrod you use, you may need to cut the lead wires back to simplify the wiring. If you decide to cut back the lead wires, it is suggested you do so in the following manner: Take the lead wires and make sure you have pulled them all the way through the top of the downrod (A). Measure 8 inches of lead wire, then cut the excess wire off with wire cutters (not included). 4 5.
WIRING WARNING: To reduce the risk of fire, electrical shock or personal injury, wire connectors provided with this fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your house wire is larger than 12-gauge and/or there is more than one house wire to connect to the two fan lead wires, consult an electrician for the proper size wire connectors to use. CAUTION: Be sure the outlet box is properly grounded or that a ground (green or bare) wire is present. 1.
FINAL INSTALLATION 1. Align the canopy (E) over the loose mounting bracket screws (R) preassembled on mounting bracket (D). Place the keyholes of the canopy (E) onto the mounting bracket screws (R) and rotate the canopy (E) clockwise. 1 D R E 2. Secure the canopy (E) with the mounting bracket screws (R) previously removed (Step 4, page 8). Tighten all mounting bracket screws (R) securely.
FINAL INSTALLATION 3. Partially insert three blade screws (BB), along with three blade washers (CC) through one blade (L) and into one blade arm (K). Tighten each blade screw (BB) with a Phillips screwdriver (not included), starting with the one in the middle. Repeat this step for the remaining blades (L) and blade arms (K). 3 BB CC Hardware Used BB Blade Screw x 15 CC Blade Washer x 15 4. Insert blade arm (K) through slot in the side of the motor assembly (H).
FINAL INSTALLATION 6. Remove one of the three light pan screws (T) from the light pan (N) and loosen the other two screws. Connect the single-pin connector from the motor assembly (H) to the single-pin connector from the light kit (G) -- Blue to Blue and White to White. Place the key holes in the light kit (G) over the two light pan screws (T) and turn clockwise. Re-install the previously removed light pan screw (T) and tighten all screws. 6 H Single-pin Connector N G T 7.
FINAL INSTALLATION 9. Remove the battery cover from the back of the remote found in remote pack (P). Insert the battery from remote pack (P) into the remote; ensure polarity of battery matches the polarity indicated in the battery compartment -- positive (+) to positive (+) and negative (-) to negative (-). Replace the battery cover and press the high fan speed button on the remote to ensure the remote turns on the fan. 9 Note: If remote does not turn on fan, see TROUBLESHOOTING (page 18).
OPERATING INSTRUCTIONS 1. To operate the fan using remote control (P), press and release the following buttons: 1 Speed Control - Controls fan speed 1 (low) - 6 (high). Fan On/Off - Turns fan off or turns fan on at most recently selected speed. Press and hold to turn off or on the sounds from the remote control. Variable Breeze - Simulates a natural breeze, as if you were outside. Press any speed control button to exit this mode.
CARE AND MAINTENANCE At least twice each year, lower the canopy to check the downrod assembly, and then tighten all screws on the fan. Clean the motor housing with only a soft brush or lint-free cloth to avoid scratching the finish. Clean the blades with a lint-free cloth. Bulb Replacement: Use 60-watt max. E26-base LED, CFL or incandescent bulbs. Halogen bulbs are not recommended for this item. Battery Replacement for Remote: Use A23 12-volt battery. Exhausted batteries should be removed from the remote.
TROUBLESHOOTING PROBLEM There is excessive wobbling. Remote control does not work. POSSIBLE CAUSE CORRECTIVE ACTION 1. The blades and/or blade arms 1. Check and tighten all screws that hold are loose. the fan blades to the blade arms and the blade arms to the motor. 2. The blades are unbalanced. 2. Switch one blade with a blade from the opposite side. Or balance the fan using a blade balancing kit (sold separately). 3. The fan mounting is not secure. 3. Turn off the power.
LIMITED LIFETIME WARRANTY The manufacturer warrants this fan to be free from defects in workmanship and materials present at time of shipment from the factory for a lifetime from the date of purchase by the original purchaser. The retailer also warrants that all other fan parts, excluding any glass or plastic blades, to be free from defects in workmanship and material at the time of shipment from the factory for a period of one year after the date of purchase by the original purchaser.
REPLACEMENT PARTS LIST For replacement parts, call the customer service department at 1-800-643-0067, 8 a.m. - 8 p.m., EST, Monday - Sunday.
