Data Sheet

10/7/21, 5:23 AM

Type 4X, 6P Polycarbonate & General Purpose ABS Enclosures (1554 Series) - Hammond Mfg.

https://www.hammfg.com/electronics/small-case/plastic/1554

1/3

Type 4X, 6P Polycarbonate & General Purpose ABS Enclosures 1554

Series

Watertight, Flat Lid, UL Listed Options

Key Features:

Ideally suited for mounting printed circuit boards or DIN rail mounted components (see

photo features below for details).

ABS Versions are molded from general purpose material which carries a flammability

rating of UL94-HB. For indoor use.

Polycarbonate versions are UV stabilized for outdoor use. Gray polycarb carries a UL94-

5VA rating, while clear and smoked lids carry a UL94V-0 rating.

Polycarbonate versions are cUL and UL 508A listed (File # E65324). ABS plastic

versions are not UL listed.

Enclosure color is a light gray (RAL 7035).

Gasketed lid with two piece “tongue & groove” construction provides protection against

access of oil, dust and water.

Replaceable gasket is one piece made from high temperature, U.L. listed silicone.

Supplied loose inside the enclosure (not pre-installed).

Polycarb versions are designed to meet NEMA Type 4, 4X, 6, 6P, 12 & 13 ratings which

meet and exceed IP ratings up to and including IP68. (Except 1554/55 V size which is

4,4X only)

ABS Plastic versions are designed to meet IP66.

Lid is secured with included M4 stainless steel machine screws which are threaded into

corrosion resistant bushings for repetitive assembly & disassembly. All hardware is

designed to avoid corrosion caused by harsh environments over time.

Lid screws are self captivating (lid holes are threaded with the first installation of lid

screws).

Internal features are maximized for mounting options and vary with size:

Internal DIN rail mounting tabs molded into most models, except sizes “C” and

“D”.

Threaded (M3) integral brass inserts and/or standoffs (#6 self tapping screws) for

P.C. board or inner panel mounting in all but the smallest size (“B”).

Vertical P.C. card guides (for 1.5 mm thick P.C. boards) are molded in all but the

smallest size (“B”).

Photo Features:

Polycarbonate versions available with gray, clear, or smoked lid. ABS version available only in

gray.

Smoked

Quality Products. Service Excellence.

PAGE 1
0/7/21, 5:23 AM Type 4X, 6P Polycarbonate & General Purpose ABS Enclosures (1554 Series) - Hammond Mfg. Quality Products. Service Excellence. Type 4X, 6P Polycarbonate & General Purpose ABS Enclosures 1554 Series Watertight, Flat Lid, UL Listed Options Key Features: Ideally suited for mounting printed circuit boards or DIN rail mounted components (see photo features below for details). ABS Versions are molded from general purpose material which carries a flammability rating of UL94-HB. For indoor use.
PAGE 2
10/7/21, 5:23 AM Type 4X, 6P Polycarbonate & General Purpose ABS Enclosures (1554 Series) - Hammond Mfg.
PAGE 3
10/7/21, 5:23 AM ABS (not UL) Type 4X, 6P Polycarbonate & General Purpose ABS Enclosures (1554 Series) - Hammond Mfg. Polycarbonate (UL Listed) Qty Lid Replacement Replacement Foot Kit Gasket Screws (50-pk) 1554RPL 1554FT 1554RGASKET SC576-50 1554HPL 1554FT 1554HGASKET SC576-50 2.40 1554HPL 1554FT 1554HGASKET SC576-50 4.70 3.50 1554HPL 1554FT 1554HGASKET SC576-50 7.10 7.10 2.36 1554WPL 1554FT 1554WGASKET SC576-50 4 7.10 7.10 3.