User's Manual

4-6
ore" softkey may have to be depressed for the "DON'T CARE" softkey to
n. rn" softkey.
4.
panel. Move the cursor to RF Control and press the "GEN"
level of -
c. cursor to the Gen RF Out position and press the "RF IN/OUT" softkey.
m the keypad enter 5.00 kHz for VHF frequencies or 5.6
f.
: The "more" softkey may have to
i.
j. C" softkey.
softkey.
he
o. ursor to the Pos (Position) position and depress the "move up" or "move
5. Setup the URC-200 (V2) as follows:
eeds 330mA, a problem exists in the transceiver. Turn off the power
b. Set the frequency presets as listed in Table 4-3 on the URC-200 (V2). For each preset
channel, adjust the URC-200 (V2) for the following. Note: Information on presetting the
URC-200 (V2) is given in Paragraph 2-3.2 located in Section 2 of this manual.
k. Move the cursor to Freq (frequency) and enter 08000.0 from the keypad.
l. Move the cursor to the DTMF Code position and press the "DON'T CARE" softkey.
Note: The "m
be displayed.
m. Press the "return" softkey. Repeat steps A through K for presets 02 through 10. Use
Table 4-3 to program the frequency presets in steps D and E above.
Press the "retu
Perform the following steps to complete the setup on the R2600 analyzer.
a. Press RF key on the R2600
softkey.
b. Move the cursor to the Output Lvl (RF Output Level) position and enter a
050.0 dBm from the keypad.
Move the
d. Depress the AUD (Audio) key on the R2600 panel. Move the cursor to the Synth
(Synthesizer) position and fro
kHz for UHF frequencies. Note: This is FM deviation. Depress the RIGHT ARROW
CURSOR CONTROL key and depress the "Cont" (Continuous) softkey.
e. Move the cursor to the Fixed 1 kHz position. Depress the LEFT ARROW CURSOR
CONTROL key and then depress the "Off" softkey.
Verify the DTMF position and the External position are both OFF.
g. Depress the DISP (Display) key on the R2600 panel. Move the cursor to the Meter
position and depress the "AC VOLTS" softkey. Note
be depressed for the "AC VOLTS" softkey to be displayed.
h. Move the cursor to the Range position and depress the "AUTO" softkey.
Move the cursor to the Display position and depress the "EXT SCOPE" softkey.
Move the cursor to the Coupling position and depress the "A
k. Move the cursor to the Trigger position and depress the "AUTO" softkey.
l. Move the cursor to the Trigger Lvl (Trigger Level) position and enter 500 from the
keypad.
m. Move the cursor to the Horiz (Horizontal) position and depress the "50 us"
Note: The "more" softkey may have to be depressed for the "50 us" softkey to be
displayed.
n. Move the cursor to the Vert (Vertical) position and depress the "5 V" softkey. Note: T
"more" softkey may have to be depressed for the "5 V" softkey to be displayed.
Move the c
down" softkeys as appropriate to center the displayed scope screen trace. Note: The
TUNING knob on the R2600 panel may be used in lieu of the “move up" or "move
down" softkeys.
p. Adjust both the SQUELCH and VOLUME controls on the front panel to their maximum
CCW positions.
a. Turn the transceiver on and note the input current. It should be approximately 240mA.
If the current exc
and troubleshoot the transceiver.