Geberit Duofix Installation Manual Montageanleitung Instructions de montage Istruzioni per il montaggio
Masse Geberit Duofix Element für Wand-WC, 112 cm, mit Sigma Unterputzspülkasten 12 cm 19¾" (500) 4¾" (120) Product Data 2⅜ (60) 100 NPT ½" Systembeschreibung 996.506.00.0 Product Specifications 71/8"–9" (180–230) Geberit Model No. / Flush volume: • 111.335.00.5 / 1.6/0.8 gpf (6.0/3.0 lpf) • 111.902.00.5 / 1.28/0.8 gpf (4.8/3.0 lpf) 2" 4" (100) (50) 2" (50) Concealed tank and bowl carrier, wall-hung twohole toilet bowl and actuator plate.
2 Installation 996.506.00.0 Montageregeln Installation Requirements To install tank and carrier, a 2 x 6" wood frame or metal frame construction is required. Studs must be placed 19 3/4" apart (clearance) where carrier will be positioned inside the wall. Bowl Finished Rim Height (FRH) 3 Remove carrier and installation hardware from its box. Determine FRH for wall-hung bowl and adjust carrier height in accordance with requirement. Dimensions can be taken from bowl or carrier specification sheet.
Tank and carrier installation 1 2 3 4 5 6 " 19 ¾ Locate carrier supporting studs and reinforce with additional nails. Ensure rough-in for the carrier is plumb and square. Wall framework must be affixed to the floor and ceiling for maximum support. Position carrier unit in the prepared opening. Carrier face plate must be flush with the front of the surrounding studs so that maximum support for the wall sheeting (applied later) will be accomplished.
Water supply installation 1 4 R ½'' 2 R ½'' 5 3 NPT 1/2" elbow © 06-2017 968.074.00.
8 ation Install l Manua 996.108.00.0 (00) 6 itung Montageanle montage de Instructions il montaggio per Istruzioni 9 1 Install wall surface material such as high density Gypsum / green Board, Cement Board, Tile Backer Board with optional ceramic tile finish surface as the most suitable materials. Provide cut outs for the protruding parts like inlet and outlet pipes and the rectangular access box. 2 7 6 © 06-2017 968.074.00.
Bowl installation 1 4 Remove yellow protection plugs and seals from pipes. Add dimension X and 1/8". Using that dimension, mark a line on the pipe measuring from the hub side. Cut off the pipe at the line with a pipe cutter. 1 +1/8" +(3 mm) 2 5 2 Insert discharge pipe into the pipe hub in the wall. Place a straight edge flush against the wall and mark a line on the pipe. Fit finned rubber seal onto flush pipe. Repeat same procedure for discharge pipe. X X Add dimension Y and 1/8".
Remove protective sleeves from mounting rods. Determine protruding rod length for bowl installation. Install both pipes into the hubs in the wall. A A 2 1 +13/16" +(20 mm) 2 CAUTION High torque forces WC ceramic appliance may break ` Do not overtighten hex nuts. 9 Place bowl onto rods. Attach cap washer with nose up and facing forwards onto rods. Install washer and hex nuts, tighten loosely. Level bowl. Tighten hex nuts. Snap on the bolt caps. 10 Seal gap around bowl with waterproof sealant.
C6 6 1 0Cl a r i t yI ns t a l l aonI ns t r ucons
Installation Manual Montageanleitung Instructions de montage Istruzioni per il montaggio
Sigma 12 cm Sigma 8 cm 2 D76188-001 © 06-2015 996.653.00.
4 1 5 1 2 2 6 2 00:00:45 2 1 1 3 7 1 1 1 2 2 D76188-001 © 06-2015 996.653.00.
8 11 9 12 0 mm 13 1 0 mm 10 2 90° 90° 4 D76188-001 © 06-2015 996.653.00.
16 1 0 mm 2 90° 17 15 3 2–5 cm 1 2 2 D76188-001 © 06-2015 996.653.00.
18 6l 1 3l 2 19 3 mm 6 D76188-001 © 06-2015 996.653.00.
4 1 2 1 5 2 2 6 1 00:00:45 3 2 1 D76188-001 © 06-2015 996.653.00.
7 9 1 2 10 3 8 11 0 mm 8 D76188-001 © 06-2015 996.653.00.
12 13 1 0 mm 2 90° 90° 14 1–5 cm 1 2 D76188-001 © 06-2015 996.653.00.
15 17 1 6l 0 mm 1 3l 2 2 90° 18 16 3 3 mm 2 10 1 D76188-001 © 06-2015 996.653.00.
Geberit International AG Schachenstrasse 77 CH-8645 Jona T +41 55 221 63 00 F +41 55 221 63 16 documentation@geberit.com ➔ www.geberit.com D76188-001 © 06-2015 996.653.00.
