Horizon™ icemaker Installation Instructions for Drop-In Satellite-fill™ applications HCC1000AJS, HCC1400AJS, HCC1000WJS, HCC1400WJS, HCE1000AJS, HCE1400AJS, HCE1000WJS, HCE1400WJS (See model number configurator on page 2 for details.) Order parts online www.follettice.com self-contained ia ylvan Easto n Penns NO PART E SINGLE PHAS OZ HZ PSIG VOLTS PROT ALLY THERM ECTED GE CHAR SIDE LOW IN MADE USA THE NSF SSOR OMRE UL R UL C R AMPS AMPS 208264 Stock Module Identification Plate Module No.
Horizon Series Icemaker Model Number Configurations HC Icemaker Voltage HC Horizon C 208-230/60/1 (self-contained only) Chewblet® D Low side 115/60/1 Condensing unit 208-230/60/1 (remote condensing only) E 230/50/1 C 1400 Series 1000 up to 1036 lbs (471kg) 1400 up to 1450 lbs (658kg) A V S Application Condenser A W R N Air-cooled, self-contained Water-cooled, self-contained Air-cooled, remote condensing unit Air-cooled, no condensing unit for connection to parallel rack system (self-contained
Read and complete the following 8 installation steps Unpack Site preparation 1 2 Dispenser preparation Louvered docking assembly 3 4 Ice transport tube External connection 5 6 Internal connection Front cover 7 8 Follett Corporation Equipment Return Policy Follett equipment may be returned for credit under the following conditions: 1. The equipment is new and unused. 2. A return authorization number has been issued by customer service within 30 days after shipment. 3.
Unpack Carefully unpack and inspect the contents of your Follett icemaker. 1.
Site preparation Prepare the installation site. 2 Provide drainage, water supply and electrical power to within 6 feet (2m) of icemaker in accordance with local and national codes. Outdoor installation is not recommended and will void warranty. 2.1 2.
Dispenser preparation Prepare the dispenser. 2.1 3.1 3 Dispenser preparation ➒ Hot Water ➌ ➋ ➍ 4" (101,6mm) 12" (304,8mm) min. ➐ ➊ ➎ ➏ ➓ ➐ ➑ • • • • • • • Determine best route for ice transport tube run. Note: 12" (304,8mm) clearance is required.
DROP-IN • SATELLITE-FILL self-contained 7
Louvered docking assembly Install the louvered docking assembly. 4 WARNING • Docking station must be secured in accordance with these instructions to ensure icemaker stability. • Ventilation openings in the louvered docking station should be clear of obstruction Wall bracket accessory • Mount louvered docking assembly to wall bracket accessory 4.
Undercounter installation detail – Horizon 1000 & 1400 series Top View Front View ACE BR CROSS Access panel/ door on counter ➊ 1.75" (45mm) ➌ 1.875" (48mm) 1.75" (45mm) ➍ 1000 series - 12"x16" cutout (305x407mm) 1400 series - 16"x16" cutout (407x407mm) bottom of ice machine side of ice machine CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction.
Ice transport tube Install the ice transport tube. 5.1 5 Ice transport tube installation. ➋ ➊ ➎ 1/4˝ Hot Water ➌ 1' ➍ ➏ ➐ vania Pennsyl NO Easton PART SINGLE PHASE OZ HZ VOLTS THERMA LLY PSIG E TED PROTEC CHARG SIDE LOW IN MADE USA THE NSF SOR UL OMRES R UL C R AMPS AMPS 208264 Stock Module Identification Plate Module No. Product Service No.
External connections Connect utilities to louvered docking assembly. 6.1 Air-cooled icemakers only 6.2 Water-cooled icemakers only ➋ ➌ ➋ ➍ ➊ ➊ • Remove access panel if necessary • Install drain line ➊. The rigid drain line from the icemaker must have at least 1/4" per foot pitch (6,4mm/0,3m). • Install icemaker potable water supply ➋ • Replace access panel DROP-IN • SATELLITE-FILL self-contained 6 • Remove access panel if necessary • Install drain line ➊.
Internal connections Connect louvered docking assembly to icemaker. 7 CAUTION • Plug must be accessible after final installation. • HCE1400A/W 230/50/1) requires a 20 amp circuit (4.00 mm2 wire) Air-cooled icemakers – follow steps 7.1 through 7.4. 7.1 Ice transport tube 7.2 Potable water and drain lines ➊ ➋ ➋ ➊ ➋ ➊ • Slide icemaker into louvered docking assembly ➊ • Insert ice transport tube all the way into coupling and tighten nut firmly ➋ 7.
Water-cooled icemakers – follow steps 7.5 through 7.10. 7.5 7.6 Cooling lines Ice transport tube ➋ Out In ➊ • Install icemaker cooling water lines to louvered docking assembly 7.7 • Slide icemaker into louvered docking assembly ➊ • Insert ice transport tube into coupling and tighten nut firmly ➋ 7.8 Potable water and drain lines Cooling lines and power ➊ ATTENTION INSTALLER Valve is preset at factory. Do not adjust. Adjustment will void warranty and may damage equipment.
7.9 Power cord • Remove twist tie • Carefully pass plug thru opening and plug into wall outlet 14 7.
Front cover Install front cover to icemaker. 8 Normal front cover installation Front cover installation – undercounter ➊ ➋ ➋ ➌ ➊ • Slide icemaker cover over machine ensuring that tabs on back of cover slip under louvers on back of louvered docking assembly ➊ • Insert and tighten two screws through cover and into louvered docking assembly ➋ CAUTION • Keep ventilation openings in the appliance enclosure clear of obstruction.
Long tube run recommendations ➊ max. 3 ft (.9m) ➋ 1/4˝ 1' • Pitch ice transport tube to allow melt water to drain towards icemaker ➊ • Secure insulated ice transport tube at least every 3 ft (.9m) to prevent dips or traps 801 Church Lane • Easton, PA 18040, USA Toll free (800) 523-9361 • (610) 252-7301 Fax (610) 250-0696 • www.follettice.