VISIMO (VM032+) ROLLERMO (RM032) EASIMO (EM032) ROLLERMO VISIMO EASIMO M AT INFOR ION TA N T e R O P IM re us re reference o f e b Read in for futu & reta For all customer enquiries or for replacement parts, contact:- ☎ 0870 609 1901 www.flymo.com customer.services@husqvarna.co.
Carton Contents switchbox start/stop lever lock off button cable clip x 2 grassbox handle washer x 4 wingknob x 4 Easimo only bolt x 2 upper handle grassbox upper grassbox lower grassbox tongue electric cable with moulded on plug safety flap lower handle x 2 motor cover instruction manual deck IMPORTANT ! Please check the contents of the carton are correct BEFORE assembling your new Flymo product. The Loose Parts Pack is packaged underneath the deck of the product.
Electrical 1. The British Standards Institute recommend the use of a Residual Current Circuit Device (R.C.D.) with a tripping current of not more than 30mA. Even with a R.C.D. installed 100% safety cannot be guaranteed and safe working practice must be followed at all times. Check your R.C.D. every time you use it. 2. Before use, examine cable for damage, replace it if there are signs of damage or ageing. 3. Do not use the lawnmower if the electric cables are damaged or worn 4.
Assembly Instructions A 3 2 • 1 B Assembly of Lower Handles to Deck 1. Place the bolt (A2) through the hole in the lower handle (A1) until the lower handle fits into the recess (A3) 2. Place the washer (B1) and the wing knob (B2) on to the bolt and tighten the wing knob. 3. Repeat on the other side. 1 2 C 1 3 4 5 2 D E F1 F2 The Loose Parts Pack is packaged underneath the deck. Assembly of Upper Handles to Lower Handles. 1.
Grassbox G 1 3 2 H J Visimo Only grassbox empty grassbox full Fitting Fully Assembled Grassbox to Lawnmower. 1. Lift safety flap (G1) 2. Make sure the discharge chute is clean and free from debris (G2) 3. Locate fully assembled grassbox onto 2 location points (G3) at the rear of the deck as illustrated in pic. H 4. Locate safety flap onto the top of the grassbox. Ensure the grassbox is securely located. • IMPORTANT ! AFTER FITTING ENSURE NO GAP REMAINS BETWEEN THE SAFETY FLAP AND THE GRASSBOX.
Starting and Stopping M N P Q 1 R To Start your Lawnmower 1. Form loop in mains cable and push the loop through the slot. (M) 2. To secure, position loop over the hook and pull the cable back through the slot (N). 3. Connect plug to mains and switch on. 4. Tilt the handle downwards to slightly raise the front of the lawnmower and to reduce the risk of lawn damage whilst starting. The switchbox is provided with a lock-off button (P1) to prevent accidental starting. 5.
Removing and Fitting the Blade T blade bolt washer blade V 1 2 Switch off, wait until the blade has stopped rotating and disconnect from the mains electricity supply BEFORE attempting to remove or refit the blade. Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Removing the Blade 1. To remove the blade bolt, hold the blade firmly with a gloved hand and with a spanner, loosen the blade bolt by turning it anti-clockwise (T). 2. Remove the blade bolt, washer and blade.
Caring for your Lawnmower W1 Cleaning • USE GLOVES • IMPORTANT:- It is very important that you keep your lawnmower clean. Grass clippings left in any of the air intakes or under the deck could become a potential fire hazard. 1. Remove grass from under the deck with brush. (W1) 2. Using a soft brush - remove grass clippings from all air intakes (W2), the discharge chute (W3) and the grass box (W4). 3. Visimo Only - Using a soft brush, remove grass clippings from the vision window (W5). 4.
Service Recommendations 1. 2. 3. 4. 5. We strongly recommend that your product is serviced at least every twelve months, more often in a professional application. Always use genuine Spare Parts. Prepacked spares are available from most Husqvarna Outdoor Products stockists.
EC Declaration of Conformity I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham. DL5 6UP. Certify that the product:Category.....Electric Wheeled Lawnmower Make.............. Husqvarna Outdoor Products Conforms to the specifications of Directive 2000/14/EC I, the undersigned M. Bowden of Husqvarna Outdoor Products, Aycliffe Industrial Park, NEWTON AYCLIFFE, Co. Durham.
