Datasheet

SimpliFiber Pro Multimode and Singlemode Sources
Multimode Optical Source
Emitter Type LED
Central Wavelength 850 nm, 1300 nm
Wavelength Accuracy • 850 nm: +30/- 10 nm
• 1300 nm: +/- 20 nm
Spectral Width (FWHM) • 850 nm: 50 nm (typical)
• 1300 nm: 135 nm (typical)
Minimum Output Power 850/1300 nm: ≥ -20 dBm
Power Output Stability
1
±0.1 dB over 8 hours
Auto Dual-Wavelength
Switching
Yes. Can be enabled/disabled by user.
Optical Output Connector Fixed SC
2
FindFiber Code Generation Yes. Fixed at ID 1.
Modes CW, 2 kHz modulated, Auto-wavelength
Power Requirement 2 AA Alkaline batteries.
Battery Life
3
40 hrs (typical)
Automatic Power Off 30 minutes (can be disabled by user)
Low Battery Warning Yes, LED blinks
Size (L x W x H) 5.6 in x 3.2 in x 1.6 in
(14.2 cm x 8.1 cm x 4.1cm)
Weight 9.8 oz (278 g)
Specifications
Technical Specications
New time-saving capabilities, same simple functionality
Sturdily built and encased in a durable molding, the next generation
SimpliFiber Pro LED multimode and laser singlemode sources* retain
the familiar intuitive four-button functionality from the popular
workhorse SimpliFiber line, while incorporating additional features
that make ber testing even more simple. When combined with a
SimpliFiber Pro optical power meter, these sources enable you to:
• Quickly and efciently measure power and loss at SC, LC, and
ST connections using the dual-wavelength testing feature in
which both 850 and 1300 nm or 1310 and 1550 nm wavelengths
can be transmitted simultaneously
• Conveniently save measurements taken at both wavelengths into
one record
• Eliminate time-consuming mistakes with the automatic
wavelength detection ability
• Quickly identify patch panel cable routing without the
assistance of a talk set and another technician
*The multimode source is standard in the FTK1000, FTK1300, FTK1350, and
FTK1450 kits; the singlemode source is standard in the FTK2000 and FTK1450
kits or available separately as a standalone module.
Singlemode Optical Source
Emitter Type FP Laser: dual 1310 nm/1550 nm
Central Wavelength 1310 nm, 1550 nm
Wavelength Accuracy • 1310 nm: +/- 20 nm
• 1550 nm: +/- 30 nm
Spectral Bandwidth
(RMS)
• 1310 nm: 2 nm (maximum)
• 1550 nm: 3 nm (maximum)
Minimum Output Power 1310/1550 nm: ≥ -7 dBm (typical)
Power Output Stability
1
±0.25 dB over 8 hours
Auto Dual-Wavelength
Switching
Yes. Can be enabled or disabled by user.
Optical Connector Fixed SC
2
Launch Condition 9/125 μm fiber
FindFiber Code
Generation
Yes. Fixed at ID 2.
Modes CW, 2 kHz modulated, Auto-wavelength
Power Requirement CW, 2 kHz modulated, Auto-wavelength
Battery Life
3
30 hrs (typical)
Automatic Power Off 30 minutes
(can be enabled or disabled by user)
Low Battery Warning LED blinks.
Size (L x W x H) 5.6 in x 3.2 in x 1.6 in
(14.2 cm x 8.1 cm x 4.1cm)
Weight 9.8 oz (278 grams)
Specifications (continued)
Fluke Corporation
P.O. Box 777, Everett, WA USA 98206-0777
Fluke Networks operates in more than 50 countries
worldwide. To find your local office contact details,
go to www.flukenetworks.com/contact.
©
2009 Fluke Corporation. All rights reserved.
Printed in U.S.A. 1/2009 3441675 D-ENG-N Rev A
NETWORKSUPERVISION
1
23
°
C ± 2
°
C, after 5 minutes warm-up time
2
LC and ST connectors can be tested using hybrid test-reference cord accessories.
3
In auto-wavelength mode, battery life depends on the condition and type
of batteries used. Fluke Networks recommends alkaline batteries.
Multimode source Singlemode source Both multimode and singlemode
sources are available in the
FTK1450 Complete Verification Kit