NT9005-433AUS V1.0 32 ZONE SECURITY SYSTEM Compatible with DLS2002 (and higher) downloading software Installation & Programming Guide ©2003 Digital Security Controls Ltd. Toronto • Canada • www.dsc.com Technical Support: 905-760-3036 Printed in Canada Direct all comments concerning WWW.DIYALARMFORUM.COM this publication to pubs@dscltd.com WWW.DIYALARMFORUM.
L im i te d Wa r r a n ty Digital Security Controls Ltd. warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls Ltd. shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.
High Traffic Shutdown Mode Table of Contents NOTE: The Walk Test Mode will override the High Traffic Shutdown Mode. To prolong battery life, the motion detector uses the High Traffic Shutdown feature. When motion is detected, the device will transmit to the receiver and will then shut down for 3 minutes. If motion is detected again during the shutdown time, the unit will not transmit the event to the receiver.
WARNING Please Read Carefully No t e to Ins ta ll ers This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. Sy ste m Fa i lur es This system has been carefully designed to be as effective as possible. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection.
Appendix C: WLS925L-433 Mini Door/Window Contact Remove Cover Chapter 1: Description & Operation Mount Transmitter and Magnet At the notched location on the cover, insert the flat blade of a small screwdriver between the base and the cover and twist the screwdriver to pop the cover off. Mount the backplate of the transmitter using the screws provided and replace the circuit board. The head of the screw must be below the circuit board so that the sensor is not shorted out. Use flat-headed screws only.
Appendix B: Smoke Detector Placement 1-2 System Specifications 1-2 System Specifications • • • • • The NT9005 system supports up to 32 system users. The system can be programmed using the keypad on the NT9005 control unit, or using DLS-3 downloading software and a computer. If you program the system from the NT9005 control unit, basic zone enrollment and programming can be performed using Flash Programming.
Table2: Contact ID Zone Alarm/Restoral Event Codes (as per ADEMCO): Table 3: SIA Format Automatic Zone Alarm/ Restoral Codes Program any of these codes for zone alarms/restorals when using the standard (non-automatic) Contact ID reporting format.
1-4 NT9005 Labels & Console Section # 1-4 NT9005 Labels & Console The NT9005 system comes with peel off instructions which list the Flash Programming steps for quick setup. Remove this label after installation. Refer to Chapter 4: ‘Flash Programming’, if required. The console consists of a fixed message LCD, 3 status lights (Ready, Armed and Trouble), on-board buzzer, 12 digit keypad, 3 specialized priority keys (Fire, Auxiliary, and Panic), and 5 programmable function keys.
1-5 Operation Appendix A: Reporting Codes The following tables contain Contact ID and Automatic SIA format reporting codes. For more information on reporting code formats, see section [360] to [381]. For more information on individual reporting codes, see sections [320] to [353] . where the “1” indicates which zone went into alarm. SIA Format - Level 2 (Hardcoded) The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communication Standard - October 1997.
1-5 Operation Stay Armed - (Ready light is OFF, Stay icon is ON, Bypass icon is ON), This mode is activated by pressing a function key programmed for Stay mode (default key 1), or by arming the system by entering a valid access code and not exiting the premises during the delay period. If a function key programmed with No Entry Arm is pressed or [*][9] is entered before entering an access code there will be no entry delay.
Module Programming Chapter 2: Installation [*]Function [804]-[82-85] Zone Transmitter Supervision Options [901] Installer Walk Test Enable/ Disable These eight bit toggle sections determine which wireless zones on the system are supervised. All zones that are enabled will be supervised for communication integrity, and will operate according to the zone type programmed.
2-2 NT9005 Installation Module Programming 2-2.1 Back Cover Removal: Figure 4. - Backplate of Unit Module Programming NT9204 Figure 3. Refer to Programmable Output options sections [009] to [011] [804] Wireless Zone Serial Numbers Sub Section [01] 1. 2. 3. Place the unit face down on a surface that will not scratch or mar the front cover. Remove the two screws (if required) securing the back cover to the unit (located at the bottom of unit). Retain the screws for reasssembly.
[702] Second International Option Codes OFF Land line Test Transmission is in Days 2-3 System Wiring ! The value programmed in section [370] option 7 is in days. 4 4. ON 1600 Hz Handshake The R, B, Y1, G2 terminals located on the inside of the back cover, can be configured as a Keybus, or 2 hardwired zones or 2 PGMs (programmable outputs), or 1 PGM and 1 hardwired zone .
2-3 System Wiring [702] Second International Option Codes PGM 1 and PGM 2 - are programmed in section [009], output attributes are programmed in section [141] and [142]. In this configuration there is no supervision or tamper detection of zones. An open condition will sound an alarm; a short circuit condition will not be indicated. To program the system for this configuration, enter Advanced Programming (See Chapter 3) and set section [013] option [1] to ON. 2-3.
Downloading Downloading allows programming of the entire system via a computer, modem and telephone line or PC-Link. All functions, features, changes and status, such as trouble conditions and open zones can be viewed or programmed by downloading. Refer to the DLS-3 User Manual for additional details. ☞ ☞ The NT9005 can be powered with the PC-Link 5SP connector.The DLS computer must be ready to download before the connector is attached.
Chapter 3: Programming 3-1 Programming Overview There are three methods of programming the NT9005: Flash Programming, Advanced Programming, and downloading with DLS-3 Software. DLS Software Programming DLS software enables the installer to download/ upload programming that uses DLS software. Downloading can be performed remotely with a computer, modem and telephone land line, or locally using PCLink. [*] Functions All operational functions and programming methods are accessible through [*] functions.
3-3 [*] Functions Default 003 I___I___I___I 000-014 transmissions [380] First Communicator Option Codes [4] Transmission Delay 1 This value defines the delay before transmission. The delay is for zones which have the Transmission Delay attribute enabled.
3-3 [*] Functions [*][1] ZONE BYPASSING [*][2] Trouble Announcements When Disarmed - A bypassed zone will not cause an alarm. If a zone is bypassed the panel can be armed (Ready light will be on) even if the zone is open. Use zone bypass when access is needed to part of the protected area. Damaged wiring or contacts on a zone can be temporarily bypassed until repairs can be made so that the panel can be armed.
3-3 [*] Functions This code is sent when the 128 event internal buffer has reached a level of 75% full since the last successful upload from a downloading computer. I_1_I_1_I [360] Communicator Format Options DLS Lead IN This code is sent after the panel has been successfully called by DLS, but before the panel calls DLS back via the Downloading Telephone Number when Callback is enabled. This code is also sent when ‘User Initiated Call-up’ is initiated.
3-3 [*] Functions User access codes are intended to be unique for each user. This allows the system to identify the user (by logging to the event buffer) when the system is armed, disarmed etc. HH = hours (00-23) mm = month (01-12) yy = year (00-99) E.g.
3-3 [*] Functions 25 [338] Misc. Tamper Codes These codes are sent to the Tamper Alarm and Restorals Call Direction Group programmed in section [363]. I_3_I_7_I General System Tamper This code is sent when a tamper exists on the main panel or a module. This code is sent in addition to the specific tamper. I_3_I_7_I General System Tamper Restoral I_2_I_1_I Keypad Lockout - This code is sent when the system enters keypad lockout.
Chapter 4: Flash Programming Telephone Number FLASH Flash Programming The second section of Flash Programming is the area for the central station phone number. ‘Ph00’ will be displayed. Flash Programming provides a quick way to program the system when standard options are selected or to provide a basic setup before more advanced programming is performed. Record entry information in the table provided. Instructions are also provided on a peel off label on the unit.
[301]-[311] Telephone Numbers [320]-[327] Alarm/Restoral Reporting Codes Account Information Record The telephone numbers entered here are for use by the system to send reporting codes to the central monitoring station, a residential telephone or pager. These reporting codes are used by the communicator to transmit zone alarms and restorals for zones 01-32.
Chapter 5: Advanced Programming [175] Bell Delay Timer . . . . . . . . . . . . . . . . . . . . . . . . 32 [180]-[186] Auto-arm Schedule . . . . . . . . . . . . . . . . . 33 [202]-[205] Zone Assignment . . . . . . . . . . . . . . . . . . 33 [301]-[311] Telephone Numbers . . . . . . . . . . . . . . . . 34 [301] First Telephone Number (32 Digits) . . . . . . . . . . 34 [302] Second Telephone Number (32 Digits) . . . . . . . . 34 [303] Third Telephone Number (32 Digits) . . . . . . . . .
Audible Silent Steady Pulsed Chime Bypass Force Arm Swing Tx Delay Wireless Zn. Definition Zone Section [101] 01 ( 1 2 3 4 5 6 7 8 [141-154] Programmable Output Attributes See section [009-011] for an explanation of PGM attributes.
13 14 [*][0] Quick Exit - Pressing this key will perform the Quick Exit function (if enabled). It is the equivalent of pressing [*][0] while armed. This key only works while the system is armed.This feature is enabled in section [015], option 3. Future Use 19 [*][7][3] Command Output #3 - Pressing this key is the equivalent of entering [*][7][3]. An access code may be required before the output is activated, depending on attribute 5 of the output. This key works when armed or disarmed.
[018] Sixth System Option Codes [017] Fifth System Option Codes 1 ON WLS Key does not use Access Code 1 ! OFF WLS Key uses Access Code 2 The panel will accept the disarm keycode from an unidentified wireless key, allowing arming/disarming without a code. 2 3 4 Future Use ON OFF Wireless Key Disarm Always ! 6 ON 8 OFF RF Jam Trouble Silent 7 8 ON RF Jam Trouble Disabled ! The system will monitor for RF noise or signals that will block wireless transmissions to the unit.
20 24-Hr Freeze - Similar to 24-Hr Burglary except for System Event output type and SIA identifier. 21 24-Hr Latching/Tamper - If this zone is violated, the system will not arm until [*][8][Installer’s Code] is entered. 22 Momentary Keyswitch Arm - Momentary violations of this zone will alternately arm/disarm the system. Do not use with wireless zones. 23 [001] - [004] Zone Definitions This section requires 32 two digit entries. Each two digit entry determines how the zone will operate.
OFF Audible Exit Fault Disabled The bell output will pulse with the same timing as the keypad buzzer during the Entry Delay time. For [*][9] arming, if Audible Exit fault is enabled, a violated zone will begin Entry Delay as indicated. If this option is disabled, a violated delay zone at the end the Exit Delay will cause an instant alarm. 7 ON Event Buffer follows Swinger Shutdown 5 ! 6 The event buffer can be uploaded with DLS-3 software.
10 System Event (with Event Options) - Latched System Event (Strobe). The PGM output switches to ground when any of the selected System Events (Alarms) occur on the system. In the Armed state, the output will deactivate only when an access code is entered to disarm the system. If an alarm activates this output in the disarmed state, it will deactivate if a code is entered during bell timeout or if the system arms after bell timeout.
