Use and Care Manual
SE- 0210 Laptop Defender
Stop laptop theft
PACKAGE INCLUDES:
y Laptop Defender...1PC
y USB charging cable… 1PC
y Protective Cover… 1PC
y Peel and stick adhesive
HOW TO CHARGE BATTERY:
y Charge the Laptop Defender by connecting the USB cable from the unit to the USB port.
y The green LED will be on while charging, but it will turn off automatically once the Laptop Defender is fully
charged. After disconnecting the charging cable, the unit’s red LED will flash. You may now enter your code.
y If charging for the first time, you will need to charge the Laptop Defender for 7 - 8 hours.
y Note ….the Laptop Defender comes fully charged and ready to use. No initial charging is required.
HOW TO SET THE PERSONAL CODE:
y Find the Re-Set pencil hole on the bottom of the unit and press it with a ballpoint pen or pencil. The red LED
light will begin flashing. The product is now ready for you to enter your personal code. (See drawing)
y Choose a 3-digit code and enter it. DO NOT include “ARM” in your code. ONLY use digits 1, 2 & 3.
y After pressing the selected 3-digit code, 4 beeps will sound and the red LED light will stop flashing. At this
point the code has been successfully set. There are 27 possible codes.
Note: 1. Make sure the alarm is disarmed before entering a new code.
2. If you forget your code, please follow the above steps to reset your code.
HOW TO ARM AND DISARM THE ALARM:
y Press “ARM” for 2 seconds, you will hear 1 Beep and see the red LED light flash for 3 seconds. The alarm will
then be ARMED.
y If you press “ARM” and the correct 3-digit code, you will hear 3 beeps indicating that the alarm has been
disarmed successfully.
y If the incorrect code is keyed-in, warning beeps will sound. At this point, you just need to enter the 3-digit code
correctly.
HOW TO USE THE ALARM:
y Take the Alarm out of the Protective Cover, and attach the alarm to your laptop.
y After arming the alarm, the unit will be able to detect vibrations and /or movements of your laptop. A “Beep-
Beep” sound will alert you if someone moves the alarm. If the vibration/movements stop within the next 3
seconds, the unit will return to ARMED mode.
y If the unit continuously detects two or more vibrations/ movements within the same 3-second period, the alarm
will sound continuously until you disarm the alarm.
NOTES:
y While in ARMED mode, the red LED will flash every 2 seconds.
y When resetting the code, you must enter the code within a 5-second time limit, or the alarm will automatically
revert to the pre-existing code.
y If your 3-digit code is incorrectly keyed-in 2 times in a row, the alarm will sound automatically.
y When pressing buttons on the alarm, a beep must be audible after each button selection. If a beep is not
heard, the button has not been properly entered.
y In DISARM mode, if the green LED flashes every two seconds. Then the battery is weak, please recharge
promptly or the alarm will turn off, and you will need to reset the 3-digit code.
y Ensure the unit has good battery power to operate as a security guard. Check its power level periodically.
y This product contains a rechargeable lithium battery; please keep it away from heat, fire and direct sunlight.
y Fully charge the alarm for long periods of storage.
y Put on the Protection Cover, when not in use.
WARNING:
The high-pitched alarm sound may injure hearing if in close proximity to the ears. This alarm contains small parts,
and is not suitable for children.
QUICK ALARM GUIDE:
Set Code: ARM + 3-digit code
Reset Code: 1. ARM + original 3-digit code
2. Key in new 3-digit code within short period time
To Activate the Alarm: Press ARM for 2 seconds
To Deactivate the Alarm: ARM + correct 3-digit code
Low Battery Indicator: Red Led light will flash at 30-second intervals, accompanied by a “Beep” sound, in signaling
DISARMED mode.