Proudly distributed by De’Longhi Australia Pty Limited P.O. BOX 4540 CASULA MALL NSW 2170 Customer Service Ph: 1800 126 659 Fax: 1800 706932 www.delonghi.com.au e-mail: info.au@delonghigroup.com De’Longhi Appliances via Seitz, 47 31100 Treviso Italia www.delonghi.com 5711413321_00_0418 De’Longhi New Zealand Limited 99 Khyber Pass Road Grafton 1023 Auckland, New Zealand P.O. Box 58-056 Botany MANUKAU 2163 Customer Service Ph: 0508 200 300 Fax: 0508 200 301 www.delonghi.co.nz e-mail: info.nz@delonghigroup.
HFX85W20 AIR PURIFIER, HEATER AND COOLING FAN Instructions for use This product is only suitable for well insulated spaces or occasional use
2
C Q A L1 D M F B A L G M1 K H J I R P E S 3 O K1 G1 N F1 H1
IMPORTANT WARNINGS Danger of burns!! Failure to observe the warning could result in burns or scalds. Safety warnings - WARNING: In order to avoid overheating, do not cover the heater during operation as this would lead to a dangerous rise in temperature. - WARNING: to reduce the risk of fire, keep textiles, curtains, or any other flammable material a minimum distance of 1 m from the air outlet. Danger! Failure to observe the warning may result in life threatening injury by electric shock.
- - - damage to the heater. The use of extension leads is not recommended. However if they cannot be avoided, follow the instructions accompanying the extension lead and never exceed the power limit marked on the extension. The heater must be positioned at least 50 cm from furniture or other objects. Do not use the appliance near walls, furniture, curtains, etc. Do not use the appliance in rooms with a floor area of less than 4m2.
Starting instructions mode using ventilation levels 1 through 5. Please note: the filter is provided with a protective wrapper around it that needs to be removed before first use. - Before turning on the appliance extract the filter from its housing as explained in the filter maintenance section. - Remove the wrapper covering the filter (fig.1).
Examples: cooling fan mode - - Press the temperature button or (G) to select desired temperature (within 4/5 seconds). - Press cooling fan button symbol . (M) , the display shows the - Press the speed button or (L) to increase or decrease the fan speed (within 4/5 seconds) the display will show the fan speed. Press the speed button or (L) to increase or decrease the fan speed (within 4/5 seconds). ECO function This function can be activated only inside the heating operating mode.
Oscillation button If you want the appliance to distribute the airflow over a larger area, press the oscillation button (J) on remote control. The appliance will then oscillate right and left. To stop the oscillation in the desired position, just press oscillation button (J) again. available values are the following: 0.5h; 1h; 2h; 4h; 6h; 8h; 12h. Once having set the desired time, to confirm wait about 4-5 seconds. When the programmed time has been reached, the appliance shuts off automatically.
button (H) and timer button (K) together; three brightness levels are available, the display shows: "L1", "L2", "L3" for 4-5 seconds, and within this time is possible increase or decrease the brightness level using the speed buttons (L), or respectively. Elapsed the 4-5 seconds, the last level of brightness selected will be shown on the display.
The appliance comes on with the opposite function set before it was shut off with a predefined temperature set in case of heating and a predefined speed in cooling fan. The unit is automatically programmed to remind you to change the filter. After a predefined number of working hours the unit will display CF message cyclically, indicating that the filter must be replaced. Always use original De'Longhi filters.
TROUBLESHOOTING PROBLEM CAUSE SOLUTION The display shows "pf" and emits a beep Temperature sensors are not working Please contact Customer Service properly Product doesn’t turn on Check that the plug is connected to the Plug in outlet The set temperature has been reached Use the “+” button to increase the set or the time set on the timer has elapsed temperature The appliance goes off unexpectedly Check that the plug is connected to the Plug in outlet The set temperature has been reached or the time
Check the appliance is correctly The display shows "Ht" or "It" blinking The internal temperature is too high. The air intake or outlet grille is positioned respecting the minum obstructed distances from the wall, or objects, as indicated on the instruction manual, if not, position the appliance correctly Remove the obstruction Disconnect the plug from the outlet and let the appliance cool down. After few minutes plug the appliance again.
