Setup Guide

VLT_Secondary(conf-if-po-100)# channel-member gigabitethernet 1/1, 1/2
VLT_Secondary(conf-if-po-100)# no shutdown
3 Enable VLT and congure a VLT domain.
VLT_Secondary(conf)# vlt domain 100
VLT_Secondary(conf-vlt-domain)# peer-link port-channel 100
VLT_Secondary(conf-vlt-domain)# back-up destination 10.16.206.80
VLT_Secondary(conf-vlt-domain)# peer-routing
4 Congure a VLT peer LAG.
VLT_Primary(conf)#interface gigabitethernet 1/3
VLT_Primary(conf-if-gi-1/3)#no ip address
VLT_Primary(conf-if-gi-1/3)#port-channel-protocol lacp
VLT_Primary(conf-if-gi-1/3)#port-channel 10 mode active
VLT_Primary(conf-if-gi-1/3)#no shutdown
VLT_Primary(conf)#interface port-channel 10
VLT_Primary(conf-if-po-10)#no ip address
VLT_Primary(conf-if-po-10)#switchport
VLT_Primary(conf-if-po-10)#vlt-peer-lag port-channel 10
VLT_Primary(conf-if-po-10)#no shutdown
5 Congure a VLAN
VLT_Secondary(conf)#interface vlan 100
VLT_Secondary(conf-if-vl-100)#ip address 100.1.1.2/24
VLT_Secondary(conf-if-vl-100)#tagged port-channel 10
VLT_Secondary(conf-if-vl-100)#no shutdown
VLT_Secondary(conf-if-vl-100)#exit
6 Enable BFD over OSPF.
VLT_Secondary(conf)# router ospf 1
VLT_Secondary(conf-router_ospf)# network 100.1.1.0/24 area 0
VLT_Secondary(conf-router_ospf)# bfd all-neighbors
Verify BFD conguration in VLT domain
Verify the BFD conguration in each node using the following show commands:
• To verify the BFD neighbors in the ToR, use show bfd neighbors command.
TOR#show bfd neighbors
LocalAddr RemoteAddr Interface State Rx-int Tx-int Mult Clients
* 100.1.1.3 100.1.1.1 Vl 100 Up 200 200 3 O
* 100.1.1.3 100.1.1.2 Vl 100 Up 200 200 3 O
• To verify the VLTi (ICL) link is up in the VLT primary peer, use show vlt brief command.
VLT_Primary#show vlt brief
VLT Domain Brief
------------------
Domain ID: 100
Role: Primary
Role Priority: 32768
ICL Link Status: Up
HeartBeat Status: Up
VLT Peer Status: Up
Version: 6(9)
Local System MAC address: f4:8e:38:6a:97:3f
Remote System MAC address: 00:e6:e2:f5:5c:15
Remote system version: 6(9)
Delay-Restore timer: 90 seconds
Delay-Restore Abort Threshold: 60 seconds
Peer-Routing : Enabled
Peer-Routing-Timeout timer: 0 seconds
Multicast peer-routing timeout: 150 seconds
• To verify the VLTi (ICL) link is up in the VLT secondary peer, use show vlt brief command.
VLT_Secondary#show vlt brief
VLT Domain Brief
------------------
Domain ID: 100
Role: Secondary
Role Priority: 32768
Virtual Link Trunking (VLT)
1029