Event and Error Message Reference Guide For 13th Generation Dell PowerEdge Servers Version 1.
Notes, Cautions, and Warnings NOTE: A NOTE indicates important information that helps you make better use of your computer. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates a potential for property damage, personal injury, or death. Copyright © 2014 Dell Inc. All rights reserved. This product is protected by U.S. and international copyright and intellectual property laws.
Contents 1 Introduction.........................................................................................................98 2 AMP Event Messages....................................................................................... 100 AMP0300...........................................................................................................................................100 AMP0301................................................................................................................
ASR0003............................................................................................................................................ 119 ASR0008............................................................................................................................................120 ASR0009............................................................................................................................................120 ASR0100...................................................
BAR025...............................................................................................................................................141 BAR026.............................................................................................................................................. 142 BAR027.............................................................................................................................................. 142 BAR028...............................................
BAR067.............................................................................................................................................. 164 BAR068..............................................................................................................................................164 BAR069.............................................................................................................................................. 165 BAR070................................................
BAR109.............................................................................................................................................. 186 BAR110............................................................................................................................................... 187 BAR111................................................................................................................................................187 BAR112.............................................
BAT1009............................................................................................................................................ 210 BAT1010.............................................................................................................................................210 BAT1011..............................................................................................................................................211 BAT1012................................................
BIOS013.............................................................................................................................................234 BIOS014.............................................................................................................................................235 BIOS015.............................................................................................................................................235 BIOS016.................................................
CBL0002........................................................................................................................................... 256 CBL0003............................................................................................................................................257 CBL0004........................................................................................................................................... 257 CBL0005....................................................
CPU0819............................................................................................................................................281 CPU0822........................................................................................................................................... 281 CPU9000.......................................................................................................................................... 282 11 CPUA Event Messages.....................................
CTL24................................................................................................................................................304 CTL25................................................................................................................................................ 305 CTL26................................................................................................................................................ 305 CTL27..............................................
CTL62................................................................................................................................................ 330 CTL63.................................................................................................................................................331 CTL64................................................................................................................................................ 331 CTL65.............................................
DIAG0115...........................................................................................................................................354 DIAG0121...........................................................................................................................................355 DIAG0122.......................................................................................................................................... 355 DIAG0123...................................................
DIAG0323.......................................................................................................................................... 378 DIAG0324..........................................................................................................................................378 DIAG0325.......................................................................................................................................... 379 DIAG0326....................................................
DIAG8019..........................................................................................................................................402 DIAG8020......................................................................................................................................... 402 DIAG8021..........................................................................................................................................403 DIAG8154......................................................
16 DKM Event Messages.....................................................................................426 DKM0001.......................................................................................................................................... 426 DKM0002.......................................................................................................................................... 426 DKM0003...............................................................................................
ENC5................................................................................................................................................. 450 ENC6................................................................................................................................................. 450 ENC7.................................................................................................................................................. 451 ENC8.............................................
FAN900............................................................................................................................................. 474 FAN901.............................................................................................................................................. 475 FAN902..............................................................................................................................................475 FAN903.................................................
FLDC1012.......................................................................................................................................... 497 FLDC1013..........................................................................................................................................498 FLDC1014..........................................................................................................................................498 FLDC1015.....................................................
HWC0008......................................................................................................................................... 520 HWC0009..........................................................................................................................................521 HWC0010.......................................................................................................................................... 521 HWC0011.........................................................
HWC2013.......................................................................................................................................... 544 HWC2014.......................................................................................................................................... 545 HWC2015.......................................................................................................................................... 546 HWC3000.......................................................
HWC6001..........................................................................................................................................569 HWC6002..........................................................................................................................................570 HWC6003..........................................................................................................................................570 HWC6004..........................................................
IOV1007............................................................................................................................................ 594 IOV1008............................................................................................................................................ 594 IOV1009............................................................................................................................................ 595 25 IPA Event Messages..................................
JCP005.............................................................................................................................................. 615 JCP006..............................................................................................................................................616 JCP007.............................................................................................................................................. 616 JCP008................................................
LC020................................................................................................................................................ 637 LC021.................................................................................................................................................637 LC022................................................................................................................................................638 LC023..............................................
LC062................................................................................................................................................659 LC063................................................................................................................................................660 LC064............................................................................................................................................... 660 LC065................................................
LIC202...............................................................................................................................................682 LIC203............................................................................................................................................... 683 LIC204...............................................................................................................................................683 LIC205..............................................
LOG328............................................................................................................................................. 704 LOG329............................................................................................................................................. 704 32 MEM Event Messages.................................................................................... 706 MEM0000..........................................................................................
MEM1017........................................................................................................................................... 729 MEM1200...........................................................................................................................................729 MEM1201........................................................................................................................................... 730 MEM1202.....................................................
NIC008.............................................................................................................................................. 752 NIC009.............................................................................................................................................. 753 NIC010...............................................................................................................................................753 NIC011...............................................
OSD11................................................................................................................................................ 775 OSD12................................................................................................................................................ 775 OSD13................................................................................................................................................ 776 OSD14.............................................
OSD5..................................................................................................................................................797 OSD50............................................................................................................................................... 798 OSD51................................................................................................................................................798 OSD52...............................................
PCI1302............................................................................................................................................. 818 PCI1304............................................................................................................................................. 819 PCI1306............................................................................................................................................. 819 PCI1308..............................................
PCI3015.............................................................................................................................................844 PCI3016.............................................................................................................................................845 PCI3017............................................................................................................................................. 845 PCI3018................................................
PDR1103............................................................................................................................................869 PDR1104............................................................................................................................................870 PDR1105.............................................................................................................................................871 PDR1106...................................................
PDR23................................................................................................................................................895 PDR24............................................................................................................................................... 895 PDR25............................................................................................................................................... 896 PDR26................................................
PDR62................................................................................................................................................ 921 PDR63................................................................................................................................................ 921 PDR64............................................................................................................................................... 922 PDR65..............................................
POW Event Messages.................................................................................... 946 POW000........................................................................................................................................... 946 POW001............................................................................................................................................ 946 POW002...............................................................................................
PR6.................................................................................................................................................... 968 PR7.................................................................................................................................................... 968 PR8.................................................................................................................................................... 969 PR9.........................................
PST0133............................................................................................................................................ 990 PST0134............................................................................................................................................ 990 PST0135............................................................................................................................................. 991 PST0136................................................
PSU0038..........................................................................................................................................1014 PSU0039..........................................................................................................................................1015 PSU0040..........................................................................................................................................1015 PSU0041.......................................................
PSU101............................................................................................................................................ 1039 PSU1010..........................................................................................................................................1040 PSU102............................................................................................................................................1040 PSU1050....................................................
PWR200.......................................................................................................................................... 1062 PWR2000........................................................................................................................................ 1062 PWR2001.........................................................................................................................................1063 PWR2002.........................................................
PWR2252.........................................................................................................................................1084 PWR2253.........................................................................................................................................1085 PWR2254.........................................................................................................................................1085 PWR2255..........................................................
PWR8526......................................................................................................................................... 1107 PWR8527......................................................................................................................................... 1108 PWR8528.........................................................................................................................................1108 PWR8529........................................................
PWR8569..........................................................................................................................................1131 PWR8570......................................................................................................................................... 1132 PWR8571.......................................................................................................................................... 1133 PWR8572......................................................
PWR8671.......................................................................................................................................... 1157 45 RAC Event Messages.................................................................................... 1158 RAC001............................................................................................................................................ 1158 RAC002...........................................................................................
RAC0135.......................................................................................................................................... 1178 RAC0136.......................................................................................................................................... 1179 RAC0137.......................................................................................................................................... 1180 RAC0138....................................................
RAC0217.......................................................................................................................................... 1201 RAC0218.......................................................................................................................................... 1201 RAC0219..........................................................................................................................................1202 RAC022......................................................
RAC0260......................................................................................................................................... 1223 RAC0261..........................................................................................................................................1224 RAC0262......................................................................................................................................... 1224 RAC0263.......................................................
RAC0303......................................................................................................................................... 1245 RAC0304......................................................................................................................................... 1246 RAC031............................................................................................................................................1246 RAC032.......................................................
RAC0601......................................................................................................................................... 1268 RAC0602......................................................................................................................................... 1269 RAC0603......................................................................................................................................... 1269 RAC0604.......................................................
RAC0706..........................................................................................................................................1291 RAC0707.......................................................................................................................................... 1291 RAC0708......................................................................................................................................... 1292 RAC0709......................................................
RAC1002.......................................................................................................................................... 1313 RAC1003.......................................................................................................................................... 1314 RAC1004..........................................................................................................................................1314 RAC1005.....................................................
RAC1046..........................................................................................................................................1336 RAC1047..........................................................................................................................................1336 RAC1048..........................................................................................................................................1337 RAC1049.......................................................
RAC1128.......................................................................................................................................... 1359 RAC1129.......................................................................................................................................... 1360 RAC1130.......................................................................................................................................... 1360 RAC1131....................................................
RAC1177...........................................................................................................................................1382 RAC1178.......................................................................................................................................... 1383 RAC1179.......................................................................................................................................... 1383 RAC1180....................................................
RAC949........................................................................................................................................... 1404 RAC950........................................................................................................................................... 1405 RAC951............................................................................................................................................1405 RAC952.....................................................
RAC992............................................................................................................................................1427 RAC993............................................................................................................................................1427 RAC994........................................................................................................................................... 1428 RAC995.....................................................
RED015............................................................................................................................................1448 RED016............................................................................................................................................1449 RED017............................................................................................................................................ 1450 RED018....................................................
RED057............................................................................................................................................ 1472 RED058............................................................................................................................................1473 RED059............................................................................................................................................1473 RED060....................................................
RFL2003.......................................................................................................................................... 1495 RFL2004.......................................................................................................................................... 1495 RFL2005.......................................................................................................................................... 1496 RFL2006....................................................
52 RSI Event Messages...................................................................................... 1517 RSI0001............................................................................................................................................ 1517 RSI0002............................................................................................................................................1517 RSI0003.......................................................................................
SEC0608......................................................................................................................................... 1538 SEC0609..........................................................................................................................................1538 SEC0610.......................................................................................................................................... 1539 SEC0611......................................................
SEL1500...........................................................................................................................................1560 SEL1501........................................................................................................................................... 1560 SEL1502............................................................................................................................................1561 SEL1503..................................................
STOR0109....................................................................................................................................... 1582 STOR011.......................................................................................................................................... 1583 STOR0110........................................................................................................................................1583 STOR0111.......................................................
STOR039......................................................................................................................................... 1605 STOR040.........................................................................................................................................1605 STOR041......................................................................................................................................... 1606 STOR042........................................................
STOR070......................................................................................................................................... 1627 STOR0701....................................................................................................................................... 1628 STOR0702....................................................................................................................................... 1629 STOR071.........................................................
SUP0100..........................................................................................................................................1650 SUP0101...........................................................................................................................................1651 SUP0102.......................................................................................................................................... 1651 SUP0103.....................................................
SUP022............................................................................................................................................ 1673 SUP023............................................................................................................................................ 1673 SUP024............................................................................................................................................1674 SUP025...................................................
SUP1902.......................................................................................................................................... 1695 SUP1903..........................................................................................................................................1696 SUP1904..........................................................................................................................................1696 SUP1905......................................................
SWC0034......................................................................................................................................... 1717 SWC0035......................................................................................................................................... 1717 SWC0036.........................................................................................................................................1718 SWC0037........................................................
SWC0076.........................................................................................................................................1739 SWC0077.........................................................................................................................................1740 SWC0101......................................................................................................................................... 1740 SWC0102.........................................................
SWC0141..........................................................................................................................................1761 SWC0142......................................................................................................................................... 1762 SWC0143......................................................................................................................................... 1762 SWC0144.......................................................
SWC0222.........................................................................................................................................1783 SWC0223.........................................................................................................................................1784 SWC0224.........................................................................................................................................1784 SWC0225..........................................................
SWC0264........................................................................................................................................ 1806 SWC0265........................................................................................................................................ 1806 SWC0266........................................................................................................................................ 1807 SWC0267..........................................................
SWC0306........................................................................................................................................ 1828 SWC0307........................................................................................................................................ 1829 SWC0308........................................................................................................................................ 1829 SWC0309..........................................................
SWC1923..........................................................................................................................................1851 SWC1924......................................................................................................................................... 1851 SWC1925......................................................................................................................................... 1852 SWC1926.......................................................
SYS011..............................................................................................................................................1873 SYS012............................................................................................................................................. 1874 SYS013............................................................................................................................................. 1874 SYS014...............................................
SYS057.............................................................................................................................................1896 SYS058............................................................................................................................................ 1896 SYS059.............................................................................................................................................1897 SYS060..................................................
SYS099.............................................................................................................................................1918 SYS100............................................................................................................................................. 1919 SYS1000.......................................................................................................................................... 1920 SYS1001.................................................
SYS137..............................................................................................................................................1941 SYS138............................................................................................................................................. 1942 SYS139............................................................................................................................................. 1942 SYS140...............................................
SYS179............................................................................................................................................. 1964 SYS180.............................................................................................................................................1965 SYS181............................................................................................................................................. 1965 SYS182................................................
TMP0131..........................................................................................................................................1988 TMP0132......................................................................................................................................... 1988 TMP0133......................................................................................................................................... 1989 TMP0134.......................................................
TST100.............................................................................................................................................2011 TST101............................................................................................................................................. 2011 TST102.............................................................................................................................................2012 TST103.................................................
UEFI0035........................................................................................................................................ 2032 UEFI0036........................................................................................................................................ 2033 UEFI0037........................................................................................................................................ 2034 UEFI0038......................................................
UEFI0077.........................................................................................................................................2056 UEFI0078.........................................................................................................................................2057 UEFI0079.........................................................................................................................................2057 UEFI0080......................................................
UEFI0119.........................................................................................................................................2080 UEFI0120........................................................................................................................................ 2080 UEFI0121......................................................................................................................................... 2081 UEFI0122.....................................................
USR0019..........................................................................................................................................2102 USR0020......................................................................................................................................... 2102 USR0021..........................................................................................................................................2103 USR0022.......................................................
VDR103............................................................................................................................................2126 VDR104............................................................................................................................................2126 VDR105............................................................................................................................................ 2127 VDR106....................................................
VDR40.............................................................................................................................................. 2151 VDR41...............................................................................................................................................2151 VDR42..............................................................................................................................................2152 VDR43.................................................
VF0060............................................................................................................................................ 2176 VF007...............................................................................................................................................2176 VF008...............................................................................................................................................2177 VF009.................................................
VF048.............................................................................................................................................. 2198 VF049.............................................................................................................................................. 2199 VF050.............................................................................................................................................. 2199 VF051................................................
VFL1004.......................................................................................................................................... 2220 VFL1005........................................................................................................................................... 2221 VFL1006...........................................................................................................................................2221 VFL1007...................................................
VLT0217.......................................................................................................................................... 2244 VLT0218.......................................................................................................................................... 2245 VLT0219.......................................................................................................................................... 2246 VLT0220....................................................
72 VRM Event Messages................................................................................... 2270 VRM0009........................................................................................................................................ 2270 VRM0010.........................................................................................................................................2270 VRM0011.................................................................................................
1 Introduction The Event Message Reference contains the error and event information generated by firmware and other agents that monitor system components. These events might be logged, presented to the user on one of the system management consoles, or both logged and displayed. Each event consists of the following fields: Message ID Message The unique alphanumeric identifier for the event.
Severity 2 Warning Indicates a high-impact problem where a system or component is disrupted but can remain productive and perform business-level operations. Severity 3 Information Indicates a medium-to-low impact problem that involves a partial or noncritical loss of functionality; operations are impaired but can continue to function. LCD Message The event message text that is displayed on the system's LCD. Initial Default Event messages result in event actions such as logging, SNMP or email alerts.
AMP Event Messages AMP0300 Message Arguments The system board arg1 current is less than the lower warning threshold. • arg1 = name Detailed Description None Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes. Category System Health Subcategory AMP = Amperage Severity Severity 2 (Warning) Trap/EventID 2178 LCD Message No LCD message display defined.
Category System Health Subcategory AMP = Amperage Severity Severity 1 (Critical) Trap/EventID 2177 LCD Message System board current is outside of range. Contact Support Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable AMP0302 Message Arguments The system board arg1 current is greater than the upper warning threshold.
AMP0303 Message Arguments The system board arg1 current is greater than the upper critical threshold. • arg1 = name Detailed Description Product documentation contains information on correct configuration. The failure could also be caused by a faulty component or related cabling. System performance may be degraded. Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes.
Trap/EventID 2177 LCD Message System board current is outside of range. Contact Support Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable AMP0305 Message Arguments The system board arg1 current is within range. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
Detailed Description None Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes. Category System Health Subcategory AMP = Amperage Severity Severity 2 (Warning) Trap/EventID 2178 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable AMP0308 Message Arguments Disk drive bay arg1 current is greater than the upper warning threshold. • arg1 = name Detailed Description Product documentation contains information on correct configuration. The failure could also be caused by a faulty component or related cabling. System performance may be degraded. Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes.
Subcategory AMP = Amperage Severity Severity 1 (Critical) Trap/EventID 2177 LCD Message Disk drive bay current is outside of range. Contact Support Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable AMP0310 Message Arguments Disk drive bay arg1 current is outside of range. • arg1 = name Detailed Description Product documentation contains information on correct configuration.
Arguments • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory AMP = Amperage Severity Severity 3 (Informational) Trap/EventID 2179 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable AMP0312 Message System level current is less than the lower warning threshold.
Server Administrator Trap ID Not Applicable AMP0313 Message System level current is less than the lower critical threshold. Detailed Description None Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes. Category System Health Subcategory AMP = Amperage Severity Severity 1 (Critical) Trap/EventID 2177 LCD Message System level current is outside of range.
Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable AMP0315 Message System level current is greater than the upper critical threshold. Detailed Description Product documentation contains information on correct configuration. The failure could also be caused by a faulty component or related cabling. System performance may be degraded.
Subcategory AMP = Amperage Severity Severity 1 (Critical) Trap/EventID 2177 LCD Message System level current is outside of range. Contact Support Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable AMP0317 Message System level current is within range. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes Category System Health Subcategory AMP = Amperage Severity Severity 2 (Warning) Trap/EventID 2178 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable AMP0319 Message Chassis power level current is less than the lower critical threshold.
AMP0320 Message Chassis power level current is greater than the upper warning threshold. Detailed Description Product documentation contains information on correct configuration. The failure could also be caused by a faulty component or related cabling. System performance may be degraded.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable AMP0322 Message Chassis power level current is outside of range. Detailed Description Product documentation contains information on correct configuration. The failure could also be caused by a faulty component or related cabling. System performance may be degraded.
Trap/EventID 2179 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable AMP400 Message Arguments The arg1 sensor has failed, and the last recorded value by the sensor was arg2 A. • arg1 = sensor name • arg2 = current Detailed Description The current sensor identified in the message has failed.
Detailed Description The current sensor identified in the message has failed. This condition can cause system performance issues and degradation in the moitoring capability of the system. Recommended Response Action Check the Embedded System Management (ESM) Log for any sensor related faults. If there is a failed sensor, replace the system board. For more information, contact your service provider.
Server Administrator Trap ID 5202 AMP403 Message Arguments The arg1 sensor state has changed to a warning state with a value of arg2 A. • arg1 = sensor name • arg2 = current Detailed Description The current sensor identified in the message is faulty or the current drawn by the system exceeds the warning threshold. This condition can cause system performance issues and degradation in the moitoring capability of the system.
Recommended Response Action Review system power policy, check system logs for power related failures, and review system configuration changes. For more information, contact your service provider. Category System Health Subcategory AMP = Amperage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
ASR Event Messages 3 ASR0000 Message The watchdog timer expired. Detailed Description The operating system or potentially an application failed to communicate to the baseboard management controller (BMC) within the timeout period. Recommended Response Action Check the operating system, application, hardware, and system event log for exception events.
Trap/EventID 2233 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ASR0002 Message The watchdog timer powered off the system. Detailed Description The operating system or an application failed to communicate to the baseboard management controller (BMC). The system powered off per the configured setting.
Category System Health Subcategory ASR = Auto Sys Reset Severity Severity 1 (Critical) Trap/EventID 2233 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ASR0008 Message The watchdog timer interrupt was initiated. Detailed Description The operating system or an application failed to communicate to the baseboard management controller (BMC) within the timeout period.
Detailed Description The system is communicating to the baseboard management controller (BMC). Recommended Response Action No response action is required. Category System Health Subcategory ASR = Auto Sys Reset Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ASR0100 Message The BIOS watchdog timer reset the system.
ASR0101 Message The OS watchdog timer reset the system. Detailed Description The operating system or an application failed to communicate within the timeout period. System was reset. (IPMI sensor type code 23h offset 01 - event 3:0 - 3h if booting 4h if running) Recommended Response Action Check the operating system, application, hardware, and system event log for exception events.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ASR0103 Message The OS watchdog timer powered down the system. Detailed Description The operating system or an application failed to communicate within the timeout period. The system was powered down. (IPMI sensor type code 23h offset - 02h event 3:0 - 4h) Recommended Response Action Check the operating system, application, hardware, and system event log for exception events.
Severity Severity 1 (Critical) Trap/EventID 2233 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ASR0105 Message The OS watchdog timer powered off the system. Detailed Description The operating system or an application failed to failed to communicate within the timeout period. The system was powered off.
Recommended Response Action Check the operating system, application, hardware, and system event log for exception events. Category System Health Subcategory ASR = Auto Sys Reset Severity Severity 1 (Critical) Trap/EventID 2233 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ASR0107 Message The OS watchdog timer pre-timeout interrupt was initiated.
ASR0108 Message The system returned from an OS watchdog timer event. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory ASR = Auto Sys Reset Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ASR200 Message Arguments The watchdog timer expired at arg1 .
Server Administrator Trap ID 5006 ASR201 Message Arguments The watchdog timer restarted the system at arg1 . • arg1 = day month date hh:mm:ss yyyy Detailed Description The watchdog timer has restarted the system at the date and time identified in the message, because the operating system has crashed or hung.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default OS Log;None Server Administrator Event ID 5006 Server Administrator Trap ID Not Applicable ASR203 Message Arguments The watchdog timer performed an AC power cycle on the system at arg1 .
BAR Event Messages 4 BAR001 Message Export System Profile requested. Detailed Description A system profile export operation has been requested. Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR003 Message Preparing vFlash Backup partition. Detailed Description The Backup partition is being created for storing the backup file. Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR005 Message Collecting Lifecycle Controller data. Detailed Description The Lifecycle Controller data is being collected and copied into the backup file. Recommended Response Action No response action is required.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR007 Message Export System Profile completed. Detailed Description System profile export operation is successfully completed. Recommended Response Action No response action is required.
Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR009 Message Valid vFlash media not present. Detailed Description The vFlash media is not present on the system. Recommended Response Action Insert the appropriate vFlash media in the designated vFlash portal, enable and initialize it, and retry.
Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR011 Message Unable to collect Hardware Inventory information. Detailed Description Hardware Inventory data collection and export did not complete successfully.
Recommended Response Action Do the following: 1) Download and apply the Dell Update Package (DUP) for USC. 2) Run System Services to update the database if CSIOR is not enabled. 3) Reboot the system and retry. If the issue persists after performing these operations, download the Field Service Repair software and repair the Lifecycle Controller. Download and install all the DUPs for USC, diagnostics, driver packs, and device firmware of all the devices of the host system.
BAR014 Message Backup file or partition access error. Detailed Description Unable to access the server profile Backup file and the operation cannot continue. This can be due to a media error or loss of connectivity. Recommended Response Action If using vFlash media replace media and try again. If a network share, make sure there is connectivity to and existence of the destination.
Server Administrator Trap ID Not Applicable BAR016 Message Import System Profile requested. Detailed Description A system profile import operation has been requested. Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR018 Message Backup file validation completed. Detailed Description A system profile backup file validation request has completed. Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR020 Message Restoring Lifecycle Controller data. Detailed Description The Lifecycle Controller data is being imported from the backup file. Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR022 Message System powering up to perform component updates. Detailed Description The host system is powering up to perform component firmware and configuration restoration. Recommended Response Action No response action is required.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR024 Message Initializing Restore operation. Detailed Description The restoration environment is being initialized. Recommended Response Action No response action is required.
Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR026 Message Restoring Component Configuration. Detailed Description The configuration is being set for each component. Recommended Response Action No response action is required.
Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR028 Message Host System Component Restore completed with errors, shutting down Host System. Detailed Description The component restoration on the host system has completed, but there were errors. The Host System will shutdown.
Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR030 Message Import System Profile Complete, restarting Integrated Remote Access Controller. Detailed Description The import system profile is complete.
Detailed Description RESERVED Recommended Response Action RESERVED Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR032 Message Invalid system profile Backup file. Detailed Description The system profile backup file validation did not complete successfully.
BAR033 Message Unable to Restore Lifecycle Controller data. Detailed Description A Lifecycle Controller internal data import operation did not complete successfully. Recommended Response Action Do the following: 1) Download and apply the Dell Update Package for the Unified Server Configurator (USC). 2) Run System Services to update the database if CSIOR is not enabled. 3) Reboot the system and retry the operation.
Server Administrator Trap ID Not Applicable BAR035 Message Unable to Restore Integrated Remote Access Controller configuration. Detailed Description The Integrated Remote Access Controller (iDRAC) Configuration import did not complete successfully. Recommended Response Action Manually reset the Integrated Remote Access Controller (iDRAC) configuration. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR037 Message System Reset or Lifecycle Controller Actions Canceled, System Profile Failure Recovery completed. Detailed Description Adjustments to Lifecycle and Integrated Remote Access Controller environments are complete. Recommended Response Action No response action is required.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR039 Message License not present. Detailed Description The license required for operation is not present. Recommended Response Action Use supported vFlash media and licensing for this feature, and try the operation again. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR041 Message System Shutdown. Detailed Description Shutting down host system. Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR043 Message Timeout waiting for Unified Server Configurator to exit. Detailed Description A timeout occurred waiting for the Unified Server Configurator (USC) to exit. Recommended Response Action No response action is required.
Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR045 Message Powering down the Host System for Integrated Remote Access Controller Restore. Detailed Description The host system is powering down to facilitate the import of the Integrated Remote Access Controller system profile.
Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR047 Message System Profile operation canceled by user.
Detailed Description The server motherboard does not have a Service Tag assigned, the operation cannot continue. Recommended Response Action Perform a System Profile import from a previous backup file. If no backup file is available, contact your service provider. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined.
BAR050 Message Arguments Performing Firmware Restore for Device : arg1 • arg1 = device name Detailed Description The firmware update for the specified device in progress. Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR052 Message Arguments Firmware update cannot be performed for Device: arg1 • arg1 = device name Detailed Description The required device firmware was not found, and the update cannot continue. The device firmware is either not present on the firmware storage partition or does not match the version stored in the configuration information database.
Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR054 Message System Reset or Lifecycle Controller Actions Canceled, System Profile Failure Recovery unsuccessful.
BAR055 Message Arguments Previously stored configuration values not applied to Device: arg1 • arg1 = device name Detailed Description Attempted configuration import was not successful for the specified device. Recommended Response Action The system event log captures the values that were not set, and must be reset manually. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR057 Message Arguments Some of the configuration values not applied to Device: arg1 • arg1 = device name Detailed Description The configuration import was completed, but some of the imported values were not set correctly. Recommended Response Action The system event log captures the values that were not set, and they must be reset manually.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR059 Message Validating CIFS destination access. Detailed Description The system profile import or export network destination is being tested for access. Recommended Response Action No response action is required.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR061 Message Collecting System Information. Detailed Description Collecting system information and copying it into the backup file. The operation collects system information that includes System Model and Service Tag. Recommended Response Action No response action is required.
Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR063 Message Collecting Lifecycle Controller Firmware images. Detailed Description Collecting the Lifecycle Controller firmware images and copying them in the server profile backup file. Recommended Response Action No response action is required.
Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR065 Message Collecting Integrated Remote Access Controller configuration. Detailed Description Collecting the Integrated Remote Access Controller configuration and copying it into the server profile backup file.
Recommended Response Action Enable the vFlash media and retry the operation. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR067 Message vFlash media not initialized. Detailed Description The system profile export destination is not initialized.
Detailed Description The system profile export destination is not supported. Recommended Response Action Insert, enable and initialize supported vFlash media and retry the operation. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR069 Message Insufficient space on vFlash media.
BAR070 Message NFS Destination access denied. Detailed Description Access to the NFS export/import destination is not possible or has been denied. Recommended Response Action Verify that the input parameters are correct, connectivity exists to the destination end point, and retry the operation. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable BAR072 Message Format of vFlash Backup partition unsuccessful. Detailed Description The vFlash backup partition format operation was not successful. Recommended Response Action Enable and initialize the vFlash media and retry the export. If the issue persists, try a new vFlash media or use the network share option(s). Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR074 Message Unable to collect Firmware Inventory information. Detailed Description The collection and export of firmware inventory data did not complete successfully. Recommended Response Action Apply the Dell Update Package for Unified Server Configurator (USC).
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR076 Message Unable to collect the Configuration database. Detailed Description The collection and export of Lifecycle Controller Configuration Database failed. Recommended Response Action Enter System Services in USC, and select Exit and Reboot to reset and update the database.
Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR078 Message Unable to collect the Integrated Remote Access Controller firmware. Detailed Description The collection and export of Integrated Remote Access Controller (iDRAC)firmware was not successful.
Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR080 Message Restoring Lifecycle Controller Configuration database. Detailed Description Importing the Lifecycle Controller configuration database from the system profile backup file. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR082 Message Restoring Remote Access Controller configuration. Detailed Description Remote access controller firmware and configuration import in progress.
Detailed Description System profile backup file validation failed because the host system model information does not match the value stored in the file. Recommended Response Action Obtain a valid host system backup image and try the operation again. Reboot the remote access controller and try the operation again. If the error continues, download a new remote access controller firmware image and try the operation again.
BAR085 Message Unable to collect System Information for Import Backup file validation. Detailed Description The validation of the system profile backup file has failed. The retrieval of system information to validate the backup file has failed. Recommended Response Action Restart the remote access controller, and retry the operation. If the error continues, use the remote access controller firmware to try the operation again.
Server Administrator Trap ID Not Applicable BAR087 Message Unable to Restore the Lifecycle Controller Firmware images. Detailed Description The system profile import of Lifecycle Controller firmware images has failed. Recommended Response Action Apply the Dell Update Package for this system. If the error continues, use the field service repair software to repair the Lifecycle Controller.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR089 Message Lifecycle Controller needs to be updated. Detailed Description A problem has been detected with the installation of the Unified Server Configurator (USC). This needs to be corrected before a valid Backup file can be created. Recommended Response Action Obtain the Dell update package for the Unified Server Configurator and apply it.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR091 Message System Profile Backup completed. Detailed Description A System Profile Backup request made by the user of the Unified Server Configurator interface has completed. Recommended Response Action No response action is required. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR093 Message Disconnect from CIFS unsuccessful. Detailed Description The attempt to disconnect from the specified CIFS location was not successful. Recommended Response Action If this happens on a backup request, restart the Integrated Remote Access Controller and try the operation again.
Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR095 Message Another Restore operation already in progress. Detailed Description The request to restore a System Profile from a Backup file did not complete successfully because there is already a request in progress.
Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR097 Message Lifecycle Controller Unified Server Configurator incompatibility detected.
Recommended Response Action Contact your service provider. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR099 Message Collecting License data. Detailed Description License data is being collected and copied into the backup Server Profile.
Detailed Description An error occurred accessing license data. Cannot collect license data to copy to Server Profile backup file. Recommended Response Action Refer to License Management documentation for re-installation of license(s) instructions and retry the operation. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined.
BAR102 Message Unable to restore license data. Detailed Description Unable to import license data from the backup Server Profile. Recommended Response Action Refer to iDRAC User Guide documentation license installation instructions and retry the operation. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable BAR104 Message Unable to collect system branding data. Detailed Description Unable to collect system branding data to copy to backup Server Profile. Recommended Response Action Retry the operation. If the issue persists, contact your service provider. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR106 Message Unable to restore system branding data. Detailed Description Unable to import system branding data from the backup Server Profile. Recommended Response Action Retry the operation. If the issue persists, contact your service provider. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR108 Message License to Export and Import Server Profile not present. Detailed Description The license required for Server Profile Import and Export operations to function is not present. Recommended Response Action Obtain the license for Server Profile Export and Import, install the license and retry the operation.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR110 Message All existing jobs cancelled because of Import Server Profile request processing. Detailed Description All the existing jobs are canceled during the Import Server Profile operation or if the Import operation fails.
Category Configuration Subcategory BAR = Backup/Restore Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAR112 Message The system identifier in the Server Profile file does not match the target system.
Recommended Response Action Using the iDRAC Web UI, select Server Profile from the navigation panel, and then the Automatic Backup tab. Clear Settings and reenter appropriate data, the select Schedule Backup to restart the Automatic Backup jobs. Using the RACADM CLI or WSMAN API, clear the scheduled backup settings and retry the Automatic Backup scheduling operation. Category Configuration Subcategory BAR = Backup/Restore Severity Severity 2 (Warning) LCD Message No LCD message display defined.
BAR115 Message The number of Automatic Server Profile backup files has reached the specified limit. Restarting the numbering from 1. Detailed Description The number of Automatic Server Profile backup files has reached the specified limit. Restarting the numbering from 1 which will overwrite the oldest backup file. Recommended Response Action No response action is required.
Server Administrator Trap ID Not Applicable BAR117 Message The iDRAC firmware cannot be restored due to hardware compatibility restraints. Detailed Description The firmware version for the iDRAC contained in the hardware Server Profile image is not compatible with this system hardware. Continue to use the installed firmware version or update to later versions if necessary. Recommended Response Action No response action is required.
BAT Event Messages 5 BAT0000 Message The system board battery is low. Detailed Description System settings may be preserved if input power is not removed from the power supplies. Recommended Response Action Check the system board battery at the next service window. Category System Health Subcategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 2226 LCD Message No LCD message display defined.
Trap/EventID 2227 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID 5702 Server Administrator Trap ID 5702 BAT0002 Message The system board battery has failed. Detailed Description System settings may be preserved if input power is not removed from the power supplies. Recommended Response Action Check the system board battery.
Category System Health Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 2227 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAT0004 Message The system board battery is absent. Detailed Description System settings may be preserved if input power is not removed from the power supplies.
Recommended Response Action Allow the PERC RAID controller battery to charge. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 2226 LCD Message No LCD message display defined.
BAT0007 Message The storage battery has failed. Detailed Description The PERC RAID controller battery may have failed because of thermal exceptions. Recommended Response Action 1) Verify the PERC RAID controller battery installation. 2) Check the system logs for thermal related issues. Category System Health Subcategory BAT = Battery Event Severity Severity 1 (Critical) Trap/EventID 2225 LCD Message Storage battery has failed. Check battery.
Server Administrator Trap ID Not Applicable BAT0009 Message The storage battery is absent. Detailed Description The PERC RAID controller battery may report absent due to disconnect or thermal exceptions. Recommended Response Action 1) Verify the PERC RAID controller battery installation. 2) If installed, reseat or reconnect the battery and cables. 3) Check the system logs for thermal related issues.
LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAT0011 Message Arguments The storage battery for disk drive bay arg1 is operating normally. • arg1 = bay Detailed Description None Recommended Response Action Verify the battery installation, check the system logs for thermal related issues.
Recommended Response Action 1) Verify the PERC RAID controller battery installation for the associated bay. 2) Check the system logs for thermal related issues. Category System Health Subcategory BAT = Battery Event Severity Severity 1 (Critical) Trap/EventID 2225 LCD Message Battery for disk drive bay has failed. Check battery.
BAT0014 Message Arguments The storage battery for disk drive bay arg1 is absent. • arg1 = bay Detailed Description The PERC RAID controller battery may report absent due to disconnect or thermal exceptions. Recommended Response Action 1) Verify the PERC RAID controller battery installation for the associated bay. 2) If installed, reseat or reconnect the battery and cables. 3) Check the system logs for thermal related issues.
LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAT0016 Message Arguments The arg1 battery is operating normally. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 2227 LCD Message No LCD message display defined.
Recommended Response Action Check the battery. Category System Health Subcategory BAT = Battery Event Severity Severity 1 (Critical) Trap/EventID 2225 LCD Message The battery has failed. Check battery. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BAT0018 Message Arguments The arg1 battery is present. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
BAT0019 Message Arguments The arg1 battery is absent. • arg1 = name Detailed Description System settings may be preserved if input power is not removed from the power supplies. Recommended Response Action Check the battery to confirm presence. Category System Health Subcategory BAT = Battery Event Severity Severity 1 (Critical) Trap/EventID 2225 LCD Message The battery is absent. Check battery.
Server Administrator Event ID 5703 Server Administrator Trap ID 5703 BAT0031 Message The system board battery status is unknown. Detailed Description The system battery level is unknown, and if the input power is disconnected, the system settings will not be preserved. Recommended Response Action Replace the the battery. Category System Health Subcategory BAT = Battery Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Subcategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2264 Server Administrator Trap ID 75300;80300;85300;90300;95300;100300;105300;110300;115300;120300 BAT1001 Message Arguments Battery on arg1 was replaced. • arg1 = controller name Detailed Description A controllers battery was replaced. Recommended Response Action No response action is required.
Arguments • arg1 = controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2176 Server Administrator Trap ID 115100 BAT1003 Message Arguments The battery on arg1 learn cycle has completed.
Server Administrator Event ID 2177 Server Administrator Trap ID 115100 BAT1004 Message Arguments The battery on arg1 learn cycle has timed out. • arg1 = controller name Detailed Description The controller battery must be fully charged before the learn cycle can begin. The battery may be unable to maintain a full charge causing the learn cycle to timeout. In addition, the battery must be able to maintain cached data for a specified period of time in the event of a power loss.
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2179 Server Administrator Trap ID 115100 BAT1006 Message Arguments The battery on arg1 learn cycle will start in arg2 days.
Server Administrator Trap ID 115100 BAT1007 Message Arguments The battery on arg1 learn cycle will start in arg2 hours. • arg1 = Controller name • arg2 = arg Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined.
Subcategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2188 Server Administrator Trap ID 115300 BAT1009 Message Arguments Write policy on arg1 was changed to Write Back. • arg1 = controller name Detailed Description The controller battery health has returned to normal. Recommended Response Action No response action is required.
Arguments • arg1 = Controller name Detailed Description Battery is in warn only mode and requires reconditioning. Recommended Response Action Start a learn cycle on the battery. Category Storage Subcategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined.
Server Administrator Event ID 2104 Server Administrator Trap ID 115100 BAT1012 Message Arguments The arg1 battery temperature is above normal. • arg1 = Controller name Detailed Description Diagnostic event for service to determine if there is an ambient temperature problem. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined.
Category Storage Subcategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2213 Server Administrator Trap ID 115300 BAT1014 Message Arguments arg1 battery charge in-progress. • arg1 = Controller name Detailed Description Diagnostic event for service to determine if there is an ambient temperature problem. Recommended Response Action No response action is required.
Arguments • arg1 = Controller name Detailed Description Diagnostic event for service to determine if there is an ambient temperature problem. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined.
Server Administrator Event ID 2216 Server Administrator Trap ID 115100 BAT1017 Message Arguments The arg1 battery learn mode has changed to Warn. • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined.
Category Storage Subcategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2246 Server Administrator Trap ID 115300 BAT1019 Message Arguments Battery on arg1 is charging. • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined.
Server Administrator Event ID 2278 Server Administrator Trap ID 115300 BAT1022 Message Arguments arg1 battery recondition is completed. • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined.
Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2279 Server Administrator Trap ID 115100 BAT1024 Message Arguments Errors detected with battery on arg1 . • arg1 = controller name Detailed Description The battery or the battery charger is not functioning properly. The battery may have an inadequate charge.
Arguments • arg1 = controller name Detailed Description The controller was unable to recover data from the cache. This may indicate data loss has occurred. Recommended Response Action Verify that the battery is charged and in good health. See the hardware documentation for more information. When the battery charge is unacceptably low, the battery cannot maintain cached data. Data loss may also have occurred, restoring data from backups may be needed.
Server Administrator Event ID 2338 Server Administrator Trap ID 115100 BAT1027 Message Arguments The battery on arg1 completed a charge cycle. • arg1 = controller name Detailed Description The battery successfully completed a charge cycle. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined.
Category Storage Subcategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2145 Server Administrator Trap ID 115300 BAT1029 Message Arguments The battery on arg1 can no longer recharge. • arg1 = controller name Detailed Description The controller battery cannot recharge.
Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2170 Server Administrator Trap ID 115100 BAT1031 Message Arguments The battery temperature on arg1 is above normal.
Server Administrator Event ID 2171 Server Administrator Trap ID 115300 BAT1032 Message Arguments The battery temperature on arg1 is normal. • arg1 = controller name Detailed Description The battery temperature is within the normal operating range. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) Trap/EventID 4275 LCD Message No LCD message display defined.
for information on how to safely access, or remove. Contact technical support if the issue persists. Category Storage Subcategory BAT = Battery Event Severity Severity 2 (Warning) Trap/EventID 4274 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2174 Server Administrator Trap ID 115300 BAT1034 Message Arguments The battery properties for arg1 have changed.
BAT1035 Message Arguments The battery temperature on arg1 is above the normal operating temperature. • arg1 = controller name Detailed Description The battery temperature is above normal operating temperature. Recommended Response Action No response action is required. Category Storage Subcategory BAT = Battery Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable 227
BIOS Event Messages 6 BIOS001 Message The command was successful Detailed Description The command was successful. Recommended Response Action No response action is required. Category Configuration Subcategory BIOS = BIOS Management Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS002 Message Resource allocation failure.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS003 Message Missing required parameter. Refer to the inserted comment. Detailed Description An invalid number of arguments was passed to the method. Recommended Response Action Enter all the required command parameters. Check documentation and try again.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS005 Message Mismatch in AttributeName and AttributeValue count Detailed Description The number of AttributeName and AttributeValue parameters do not match. Recommended Response Action Enter the same number of parameters for AttributeName and AttributeValue.
Subcategory BIOS = BIOS Management Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS007 Message Configuration job already created, cannot create another configuration job on specified target until existing job is completed or is cancelled Detailed Description A configuration job is already created on the specified target.
Recommended Response Action Change the configuration of one or more attributes and then create a configuration job. Category Configuration Subcategory BIOS = BIOS Management Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS009 Message Lifecycle Controller is currently in use.
Detailed Description For 11G systems: System Services must be enabled to perform the requested operation. System Services has been disabled through the iDRAC configuration utility accessed by pressing CTRL+E on boot up or through a remote operation. For 12G systems: Lifecycle Controller must be enabled to perform the requested operation.
Server Administrator Trap ID Not Applicable BIOS012 Message No pending data to delete. Detailed Description No changes to BIOS attribute data are available between the previous configuration and the current configuration. Recommended Response Action No response action is required. Category Configuration Subcategory BIOS = BIOS Management Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS014 Message Arguments Invalid AttributeValue for AttributeName: arg1 • arg1 = attribute name Detailed Description AttributeValue may be invalid because of the following causes: 1) Length of new AttributeValue is not within required minimum length and maximum length 2) Value of new AttributeValue is not within required LowerBound and UpperBound 3) Value of new Attributevalue is not one of the possible values.
Recommended Response Action No response action is required. Category Configuration Subcategory BIOS = BIOS Management Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS016 Message Arguments AttributeValue cannot be changed for disabled AttributeName arg1 .
BIOS017 Message Unable to delete vFlash pending one-time boot configuration Detailed Description Unable to delete vFlash pending one-time boot configuration. Recommended Response Action Remove AC power from system and after restoring AC power, retry the operation. Category Configuration Subcategory BIOS = BIOS Management Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable BIOS021 Message Cannot authenticate BIOS password. Detailed Description The old BIOS password specified in the change BIOS password operation was incorrect. Recommended Response Action Retry the operation with correct old BIOS password. Category Configuration Subcategory BIOS = BIOS Management Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS023 Message Cannot perform the operation due to an unknown error in iDRAC. Detailed Description An unrecoverable error occurred in the operation while communicating with iDRAC. Recommended Response Action Retry the operation. If the issue continues, reset the iDRAC. Category Configuration Subcategory BIOS = BIOS Management Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS025 Message Unable set the BIOS password as the BIOS password status is locked. Detailed Description The status of the password is Locked in BIOS and must be set to Unlocked for the operation to succeed. Recommended Response Action Change BIOS password status in the BIOS setup from Locked to Unlocked and retry the operation.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS027 Message Arguments Unable to change the BIOS password because the password is currently being configured using plain text. Unable to set the attribute arg1 . • arg1 = attribute name Detailed Description The attribute identified in the message cannot be set, because the password is currently being reset by using plain text.
Recommended Response Action Wait until the current password configuration process is completed and retry the operation. Category Configuration Subcategory BIOS = BIOS Management Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BIOS029 Message Unable to change the BIOS password because an Export Server Profile operation is already running.
Detailed Description The BIOS password cannot be configured because an Import Server Profile operation is already running. Recommended Response Action Wait until the current import operation is completed, and then retry the operation. Category Configuration Subcategory BIOS = BIOS Management Severity Severity 2 (Warning) LCD Message No LCD message display defined.
BIOS102 Message A system BIOS update is scheduled that requires a reboot. Detailed Description A BIOS update job is scheduled through the remote access controller, and the system must be rebooted to apply the update. Recommended Response Action Reboot the system to apply the BIOS update. Category Audit Subcategory BIOS = BIOS Management Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable 245
BOOT Event Messages BOOT001 Message The command was successful. Detailed Description The command was successful. Recommended Response Action No response action is required. Category Configuration Subcategory BOOT = BOOT Control Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BOOT003 Message Method not supported Detailed Description This operation is not supported on the current configuration. Recommended Response Action This operation is not supported on the current configuration, check documentation and try again Category Configuration Subcategory BOOT = BOOT Control Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BOOT005 Message Missing required parameter. Detailed Description One or more of the invoked methods required parameters are missing. Recommended Response Action Check documentation for the method in question and try again.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BOOT007 Message Boot Source does not belong to specified Boot Configuration Detailed Description One or more of the Boot Source instance IDs does not belong to the affected Boot Configuration.
Subcategory BOOT = BOOT Control Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BOOT009 Message Boot Sources cannot be found for this Boot Configuration Detailed Description No Boot Sources could be found for the desired Boot Configuration.
Category Configuration Subcategory BOOT = BOOT Control Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BOOT011 Message Failed to set vFlash partition for one time boot Detailed Description The provided vFlash partition could not be set for one time boot.
Recommended Response Action No response action is required. Category Configuration Subcategory BOOT = BOOT Control Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable BOOT013 Message Cannot make changes to non-active boot list. Detailed Description The boot list is currently not active. Changes cannot be made to boot list that is not active.
Detailed Description The systems SD card has been removed or is in use. Recommended Response Action Verify that the SD card is inserted and that another operation is not in progress, and try again. Category Configuration Subcategory BOOT = BOOT Control Severity Severity 3 (Informational) LCD Message No LCD message display defined.
BOOT016 Message Input source argument value for the boot device is incorrect or not found among the boot devices on the system. Detailed Description The input source argument value referring to the boot device is incorrect or empty. The boot device identifier must match the InstanceID for the BootSourceSetting instance that represents the boot device. Recommended Response Action Use the correct source argument value for the boot device and retry the operation.
Server Administrator Trap ID Not Applicable BOOT018 Message Specified Boot Control List is read-only Detailed Description The Boot Control List specified in the operation is read-only and cannot be modified. Recommended Response Action Refer to the documentation on validity of operation for the Boot Control List specified. For more information on the operation, see Lifecycle Controller-Remote Services documentation.
CBL Event Messages 8 CBL0001 Message Arguments Backplane arg1 power cable disconnected. • arg1 = bay ID Detailed Description A backplane signal cable was detected, but the accompanying power cable was not present. Recommended Response Action Reconnect or replace the power cable. If the issue persists, contact your service provider. Category System Health Subcategory CBL = Cable Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Subcategory CBL = Cable Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CBL0003 Message Arguments Backplane arg1 arg2 cable is disconnected. • arg1 = bay ID • arg2 = cable name Detailed Description The backplane cable identified in the message is disconnected or no cable is detected.
• arg2 = bay ID • arg3 = connector name Detailed Description The cable identified in the message is incorrectly connected to the backplane connector. Recommended Response Action Make sure the cable identified in the message is cabled correctly. If the issue persists, contact your service provider. Category System Health Subcategory CBL = Cable Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable CBL0006 Message Arguments Unsupported backplane arg1 configuration: Multiple RAID controllers cannot be connected to the same backplane. • arg1 = bay ID Detailed Description Each server model only supports a certain set of backplane configurations. For unified backplanes or split mode capable backplanes that are in unified mode, multiple controllers cannot be connected to the same backplane.
Recommended Response Action Make sure the cables identified in the message are cabled correctly. If the issue persists, contact your service provider. Category System Health Subcategory CBL = Cable Severity Severity 1 (Critical) LCD Message No LCD message display defined.
CMC Event Messages 9 CMC401 Message Arguments Changing the Reserved QuickDeploy IP Addresses setting to arg1 may create an issue in the future if higher density server nodes are inserted in to the Chassis (for example, quarter-height servers). Press OK to continue.
CPU Event Messages 10 CPU0000 Message Arguments CPU arg1 has an internal error (IERR). • arg1 = number Detailed Description System event log and OS logs may indicate that the exception is external to the processor. Recommended Response Action Review System Event Log and Operating System Logs. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Recommended Response Action Review logs for fan failures, replace failed fans. If no fan failures are detected, check inlet temperature (if available) and reinstall processor heatsink. Category System Health Subcategory CPU = Processor Severity Severity 1 (Critical) Trap/EventID 2241 LCD Message CPU has a thermal trip.
CPU0003 Message Arguments CPU arg1 is stuck in POST. • arg1 = number Detailed Description None Recommended Response Action 1) Turn off the server and disconnect input power for one minute. Re-apply input power and turn system on. 2) Reduce system configuration to minimum memory and remove all PCI devices. If system completes POST, update system BIOS. Reinstall memory and PCI one component at a time to meet the original configuration. 3) If the issue still persists, contact technical support.
Severity Severity 1 (Critical) Trap/EventID 2241 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CPU0005 Message Arguments CPU arg1 configuration is unsupported. • arg1 = number Detailed Description System is unable to boot or may run in a degraded state. Recommended Response Action Review product documentation for supported CPU configurations.
Detailed Description System is unable to boot or may run in a degraded state. Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly. 3) If the issue still persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Server Administrator Trap ID 5602 CPU0008 Message Arguments CPU arg1 is disabled. • arg1 = number Detailed Description System is unable to boot or may run in a degraded state. Recommended Response Action if unexpected, check presence, and system setup (BIOS) configuration. Category System Health Subcategory CPU = Processor Severity Severity 2 (Warning) Trap/EventID 2242 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 2243 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CPU0010 Message Arguments CPU arg1 is throttled. • arg1 = number Detailed Description The CPU is throttled due to thermal or power conditions. Recommended Response Action Review system logs for power or thermal exceptions.
Detailed Description None. Recommended Response Action Review System Event Log and Operating System Logs. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory CPU = Processor Severity Severity 1 (Critical) Trap/EventID 2241 LCD Message Uncorrectable Machine Check Exception detected on CPU .
Server Administrator Trap ID 5603 CPU0016 Message Arguments CPU arg1 is operating correctly. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory CPU = Processor Severity Severity 3 (Informational) Trap/EventID 2243 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 2243 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CPU0024 Message Arguments CPU arg1 is enabled. • arg1 = number Detailed Description None Recommended Response Action No response action is required.
Detailed Description System is unable to boot or may run in a degraded state. Recommended Response Action Check presence and reinstall the terminator. Category System Health Subcategory CPU = Processor Severity Severity 2 (Warning) Trap/EventID 2242 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CPU0700 Message Arguments CPU arg1 initialization error detected.
Server Administrator Trap ID Not Applicable CPU0701 Message Arguments CPU arg1 protocol error detected. • arg1 = number Detailed Description System event log and OS logs may indicate that the exception is external to the processor. Recommended Response Action 1) Check system and operating system logs for exceptions. If no exceptions are found continue. 2) Turn system off and remove input power for one minute. Reapply input power and turn system on. 3) Make sure the processor is seated correctly.
Trap/EventID 2241 LCD Message CPU bus parity error detected. Power cycle system Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CPU0703 Message CPU bus initialization error detected. Detailed Description System event log and OS logs may indicate that the exception is external to the processor. Recommended Response Action 1) Check system and operating system logs for exceptions. If no exceptions are found continue.
Recommended Response Action 1) Check system and operating system logs for exceptions. If no exceptions are found continue. 2) Turn system off and remove input power for one minute. Reapply input power and turn system on. 3) Make sure the processor is seated correctly. 4) If the issue still persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Server Administrator Trap ID Not Applicable CPU0801 Message Arguments CPU arg1 voltage regulator module failed. • arg1 = number Detailed Description System performance may be degraded or the system may fail to operate. Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly. 3) If the issue still persists, contact technical support.
Subcategory CPU = Processor Severity Severity 2 (Warning) Trap/EventID 2242 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CPU0803 Message Arguments The power input for CPU arg1 voltage regulator module is lost. • arg1 = number Detailed Description System performance may be degraded or the system may fail to operate.
Arguments • arg1 = number Detailed Description System performance may be degraded or the system may fail to operate. Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly. 3) If the issue still persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CPU0806 Message Arguments CPU arg1 voltage regulator module is incorrectly configure. • arg1 = number Detailed Description System performance may be degraded or the system may fail to operate. Recommended Response Action Review product documentation for proper configuration and installation procedures.
Recommended Response Action if removal was unintended, check presence and re-install . Category System Health Subcategory CPU = Processor Severity Severity 1 (Critical) Trap/EventID 2241 LCD Message CPU voltage regulator module absent. Check module Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CPU0817 Message Arguments CPU arg1 voltage regulator module is operating normally.
CPU0819 Message Arguments The power input for CPU arg1 voltage regulator module has been restored. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory CPU = Processor Severity Severity 3 (Informational) Trap/EventID 2243 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CPU9000 Message An OEM diagnostic event occurred. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory CPU = Processor Severity Severity 3 (Informational) LCD Message No LCD message display defined.
CPUA Event Messages 11 CPUA0023 Message Arguments CPU arg1 is absent • arg1 = number Detailed Description None Recommended Response Action Verify processor installation. If present, reseat the processor. Category System Health Subcategory CPUA = Proc Absent Severity Severity 1 (Critical) Trap/EventID 2457 LCD Message CPU is absent.
CTL Event Messages 12 CTL1 Message Arguments Controller event log: arg1 • arg1 = message Detailed Description This event is retrieved from the controller when iDRAC storage monitoring was not running. Such events which are generated in the past are logged as informational severity. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2156 Server Administrator Trap ID 75100 CTL100 Message Arguments The Patrol Read operation aborted for arg1 .
CTL11 Message Arguments Configuration on arg1 was reset. • arg1 = controller name Detailed Description A user operation to reset the controller configuration was performed. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2182 Server Administrator Trap ID 75400 CTL13 Message Arguments The arg1 cache has been discarded. • arg1 = Controller name Detailed Description The controller has flushed the cache and all data in the cache has been lost. This may occur when the system has memory or battery problems that cause the controller to distrust the cache.
Detailed Description The storage controller memory identified in th emessage is not operating correctly. Recommended Response Action COntact your service provider. Category Storage Subcategory CTL = Storage Contr Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2187 Server Administrator Trap ID 75300 CTL16 Message Arguments None of the arg1 properties are set.
Server Administrator Trap ID 75100 CTL17 Message Arguments arg1 arg2 is changed to arg3 . • arg1 = Controller Name • arg2 = propertyname • arg3 = new value Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2222 Server Administrator Trap ID 75100 CTL19 Message Arguments Abort CC on Error, Copyback, and Load Balance has changed for arg1 . • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command.
Arguments • arg1 = Controller name Detailed Description You have changed the controller rebuild rate. This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Server Administrator Event ID 2224 Server Administrator Trap ID 75100 CTL200 Message Arguments The current firmware version arg1 is older than the required version arg2 for arg3 . • arg1 = version number • arg2 = version number • arg3 = controller name Detailed Description The firmware on the controller identified in the message is not a supported version. Recommended Response Action Download the supported version from the service provider and install it on the controller.
Detailed Description The controller driver for the identified controller is not a supported version. Recommended Response Action Download the supported version of the driver from the service provider and install it on the operating system. Category Storage Subcategory CTL = Storage Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID 75300 CTL203 Message Arguments Abort Check Consistency on Error, Copyback or Auto Copyback on Predictive Failure, and Load Balance values are changed for arg1 . • arg1 = controller name Detailed Description The status of the changed attribute values are reported for information purposes. Recommended Response Action No response action is required.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2220 Server Administrator Trap ID 75100 CTL205 Message Arguments Auto Copyback on Predictive Failure, Abort Check Consistency on Error, and Load Balance values are changed for arg1 . • arg1 = controller name Detailed Description The status of the changed attribute values are reported for information purposes.
Detailed Description The status of the changed attribute values are reported for information purposes. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2227 Server Administrator Trap ID 75100 CTL207 Message Arguments Unable to import the Virtual Disk because the supported limit is exceeded on arg1 .
CTL208 Message Arguments Unable to authenticate the entered passphrase for the arg1 . • arg1 = controller name Detailed Description Unable to authenticate the entered passphrase. Recommended Response Action Enter the correct passphrase and retry. Category Storage Subcategory CTL = Storage Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID 2394 Server Administrator Trap ID 75100 CTL21 Message Arguments Abort CC on Error and Load Balance has changed for arg1 . • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2395 Server Administrator Trap ID 75100 CTL211 Message Arguments The arg1 property changed on arg2 through Manage Physical Disk Power option. • • arg1 = property name arg2 = controller name Detailed Description The physical disk properties displayed under "Manage Physical Disk Power" option has changed.
Detailed Description This alert is generated when the encryption key in the controller is deleted. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2388 Server Administrator Trap ID 75100 CTL213 Message Arguments The Local Key Management (LKM) is enabled on arg1 .
CTL214 Message Arguments The Local Key Management (LKM) encryption key in the arg1 has changed. • arg1 = controller name Detailed Description The Local Key Management (LKM) encryption key in the controller identified in the message has changed. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2250 Server Administrator Trap ID 75100 CTL216 Message Arguments Redundant path connection is restored on arg1 . • arg1 = Controller Name Detailed Description The communication in the redundant path on the connectors of the controller identified in the message is restored. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2370 Server Administrator Trap ID 120100 CTL22 Message Arguments Load Balance has changed for arg1 . • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command.
CTL23 Message Arguments Copyback and Auto Copyback on Predictive Failure has changed for arg1 . • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2229 Server Administrator Trap ID 75100 CTL25 Message Arguments Auto Copyback on Predictive Failure has changed for arg1 . • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command.
Recommended Response Action Re-issue the command. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2231 Server Administrator Trap ID 75100 CTL27 Message Arguments The arg1 alarm is silenced. • arg1 = Controller name Detailed Description This alert is provided for informational purposes.
CTL28 Message Arguments The Background Initialization (BGI) rate has changed for arg1 . • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2234 Server Administrator Trap ID 75100 CTL3 Message Arguments arg1 alarm is enabled. • arg1 = Controller name Detailed Description You have enabled the controller alarm. This alert is provided for informational purposes. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2235 Server Administrator Trap ID 75100 CTL31 Message Arguments Copyback is modified for arg1 . • arg1 = Controller name Detailed Description This alert is provided for informational purposes.
CTL32 Message Arguments Abort CC on Error is modified for arg1 . • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action Re-issue the command. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2238 Server Administrator Trap ID 75100 CTL34 Message Arguments A foreign configuration was cleared on arg1 . • arg1 = controller name Detailed Description This is the result of a user operation. Recommended Response Action No response action is required.
Recommended Response Action Verify the foreign configuration was successfully imported by viewing the virtual disks and hot spares. See the hardware documentation for more information. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2240 Server Administrator Trap ID 75100 CTL36 Message Arguments The Patrol Read mode has changed for arg1 .
CTL37 Message Arguments A Patrol Read operation started for arg1 . • arg1 = controller name Detailed Description A patrol read operation was initiated by the controller or the user. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2243 Server Administrator Trap ID 75100 CTL39 Message Arguments The arg1 reconstruct rate has changed. • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2144 Server Administrator Trap ID 75100 CTL40 Message Arguments Multi-bit ECC error on arg1 DIMM.
Server Administrator Trap ID 75400 CTL41 Message Arguments Single-bit ECC error on arg1 . • arg1 = Controller name Detailed Description An error involving a single bit has been encountered during a read or write operation. The error correction algorithm has corrected this error. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2304 Server Administrator Trap ID 75100 CTL43 Message Arguments Diagnostic message arg1 from arg2 • arg1 = args • arg2 = Controller name Detailed Description This alert is provided for informational purposes. The text for this alert is generated by the utility that ran the diagnostics and can vary depending on the situation.
• arg2 = Controller name Detailed Description A diagnostics test failed. The text for this message is generated by the tool that ran the diagnostics and can vary depending on the situation. Recommended Response Action Refer to the storage hardware documentation for more information on the diagnostic test. Category Storage Subcategory CTL = Storage Contr Severity Severity 1 (Critical) Trap/EventID 4329 LCD Message No LCD message display defined.
Server Administrator Trap ID 75300 CTL46 Message Arguments Single-bit ECC error. The arg1 DIMM is critically degraded. • arg1 = Controller name Detailed Description The Dual In-line Memory Module (DIMM) is malfunctioning. Data loss or data corruption may occur.. Recommended Response Action Replace the DIMM immediately to avoid data loss or data corruption. The DIMM is a part of the controller battery pack. Refer to the storage hardware documentation for information on replacing the DIMM.
Severity Severity 1 (Critical) Trap/EventID 4329 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2321 Server Administrator Trap ID 75400 CTL48 Message Arguments A foreign configuration was detected on arg1 . • arg1 = controller name Detailed Description The controller has physical disks that were moved from another controller or have been removed and replaced on the current configuration.
CTL49 Message Arguments The NVRAM has corrupted data on arg1 . • arg1 = Controller name Detailed Description The NVRAM has corrupted data. This may occur after a power surge, a battery failure, or for other reasons. The controller is reinitializing the NVRAM. Recommended Response Action No response action is required as the controller is taking the required corrective action. However, If this message is generated often (such as during each reboot), then replace the controller.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2146 Server Administrator Trap ID 75300 CTL50 Message Arguments The arg1 NVRAM has corrupt data. • arg1 = Controller name Detailed Description The NVRAM has corrupt data. The controller is unable to correct the situation. Recommended Response Action Replace the controller.
Detailed Description The text for this message is generated by the controller during runtime and can vary depending on the situation. Recommended Response Action Make sure the SAS cables attached to the enclosure/backplane are attached securely. Refer to the storage hardware documentation for more information on checking the cables. Contact technical support if the issue persists.
Server Administrator Trap ID 75100 CTL53 Message A controller hot plug has been detected. Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2266;2334 Server Administrator Trap ID 75100;80100;85100;90100;95100;100100;105100;110100;115100;120100 CTL55 Message Arguments arg1 event log: arg2 • arg1 = Controller name • arg2 = args Detailed Description The text for this alert is generated by the controller and can vary depending on the situation.
Arguments • arg1 = Controller name • arg2 = args Detailed Description The text for this alert is generated by the controller and can vary depending on the situation. This text is from events in the controller event log that were generated while Storage Management was not running. Recommended Response Action See the hardware documentation for more information.
Server Administrator Event ID 2339 Server Administrator Trap ID 75100 CTL58 Message Arguments arg1 SAS SMP communications error arg2 • arg1 = Controller name • arg2 = args Detailed Description The text for this alert is generated by the firmware and can vary depending on the situation. The reference to SMP in this text refers to SAS Management Protocol. Recommended Response Action There may be a SAS topology error.
Detailed Description There may be a problem with the enclosure. Verify the health of the enclosure and its components. To verify the health of the enclosure, select the enclosure object in the tree view. The Health sub-tab displays a red X or yellow exclamation point for enclosure components that are failed or degraded. See the enclosure documentation for more information. Recommended Response Action There may be a problem with the enclosure. Verify the health of the enclosure and its components.
Server Administrator Event ID 2147 Server Administrator Trap ID 75300 CTL60 Message Arguments A user has discarded data from the arg1 cache. • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Recommended Response Action Shut down the system. Re-insert the removed physical disks and re-start the system. Category Storage Subcategory CTL = Storage Contr Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2361 Server Administrator Trap ID 75300 CTL62 Message Arguments arg1 on arg2 has missing drives and will go offline at boot.
Server Administrator Trap ID 75100 CTL63 Message Arguments Previous configuration was found completely missing during time boot on arg1 . • arg1 = Controller name Detailed Description The controller is unable to retrieve storage configuration saved during last shut down. This can generally happen if some configured physical disks are removed from the system when the system was shutdown. Recommended Response Action Shut down the system. Re-insert the removed physical disks and re-start the system.
Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2371 Server Administrator Trap ID 75100 CTL65 Message Arguments Attempted to import Unsupported Virtual Disk type RAID arg1 on arg2 . • arg1 = args • arg2 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
Arguments • arg1 = args • arg2 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Server Administrator Event ID 2374 Server Administrator Trap ID 75100 CTL68 Message Arguments Attempted to import Virtual Disk with missing Physical Disk on arg1 . • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2376 Server Administrator Trap ID 75100 CTL7 Message Arguments Bad block medium error on arg1 . • arg1 = Controller name Detailed Description A portion of a physical disk is damaged. See Receive a "Bad Block" Alert with "Replacement," "Sense," or "Medium" Error for more information.
Arguments • arg1 = Controller name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Server Administrator Event ID 2378 Server Administrator Trap ID 75100 CTL72 Message Arguments The foreign configuration overflow has occurred on arg1 . • arg1 = Controller name Detailed Description There is too much foreign configuration data to be imported in one attempt. Recommended Response Action Import these foreign configurations in multiple attempts.
Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2380 Server Administrator Trap ID 75100 CTL74 Message Arguments Preserved cache detected on arg1 .
CTL75 Message Arguments Preserved cache discarded on arg1 . • arg1 = controller name Detailed Description The controller cache was discarded by the user. Data may have been lost or corrupted. Recommended Response Action If data was corrupted or lost, restore the data to the disk from a backup copy. Category Storage Subcategory CTL = Storage Contr Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2401 Server Administrator Trap ID 75400 CTL77 Message Arguments Flash of new firmware image(s) completed on arg1 • arg1 = Controller Name Detailed Description This alert message occurs if controller firmware is flashed successfully. Recommended Response Action No response action is required.
Detailed Description This alert message occurs if controller firmware is flashed. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable CTL8 Message Arguments Bad block extended sense error on arg1 .
Server Administrator Trap ID 75300 CTL81 Message Arguments Security key assigned to arg1 is modified. • arg1 = controller name Detailed Description The security key assigned to the controller identified in the message is modified. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Severity Severity 2 (Warning) Trap/EventID 4330 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2150 Server Administrator Trap ID 75300 CTL97 Message Arguments arg1 personality changed to arg2 mode. • • arg1 = controller name arg2 = new mode Detailed Description The controller identified in the message has been changed to a new personality mode (HBA or RAID). Recommended Response Action No response action is required.
Detailed Description The security key provided as input has been assigned to the controller identified in the message. Recommended Response Action No response action is required. Category Storage Subcategory CTL = Storage Contr Severity Severity 3 (Informational) Trap/EventID 4331 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable 345
DH Event Messages 13 DH001 Message Resource needed to perform the operation is unavailable. Detailed Description Resource temporarily unavailable Recommended Response Action Try again. If the error persists, use RACADM command racreset to clear the issue. Category Configuration Subcategory DH = Cert Mgmt Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DH003 Message Service tag could not be read Detailed Description Service Tag Missing Recommended Response Action Try again. If the error persists, use RACADM command racreset to clear the issue. Category Configuration Subcategory DH = Cert Mgmt Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DH005 Message CA Cert is corrupted, expired, or does not have signing privileges. Detailed Description Invalid CA Cert Recommended Response Action Close other iDRAC sessions and activities. Try again. Category Configuration Subcategory DH = Cert Mgmt Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DH007 Message The password unlocked the private key but it was the wrong private key. Detailed Description CA priv key/CA Cert mismatch Recommended Response Action Check that the private key parameter is correct.
Subcategory DH = Cert Mgmt Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DH009 Message The operation did not complete successfully because of an unexpected internal problem.. Detailed Description An unexpected internal problem has occurred and the operation did not complete successfully.
Recommended Response Action Reset the iDRAC. The iDRAC can be reset by pressing the Identify button for 15 seconds. Using the RACADM command line utility, run "racadm racreset" Category Configuration Subcategory DH = Cert Mgmt Severity Severity 3 (Informational) LCD Message No LCD message display defined.
DIAG Event Messages DIAG0000 Message Pass Detailed Description All Tests passed Recommended Response Action OK, life is good. Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0111 Message Arguments CPU arg1 : arg2 exception occurred.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0112 Message Arguments CPU arg1 - Machine check exception detected. • arg1 = Cpu Number Detailed Description Recommended Response Action Issue is on system board. Recommend flash the latest BIOS and retry the diagnostics.
other CPU messages could result from hardware or from overheating, if for instance, the fans are marginal or airflow is blocked. Recommended Response Action Check temperatures in System Health tab for abnormally high temperatures and make sure airflow baffles are properly installed in the system, if any. Check fan RPM in System Health tab and verify actual fans are properly installed.
DIAG0121 Message Memory errors detected, but successfully resolved. Detailed Description Recommended Response Action MemRx is enabled and repaired all memory errors that were found. DIMM replacement is optional. Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable DIAG0123 Message UEFI: Memory error detected. :OR: LEGACY: Memory - integrity test discrepancy. Detailed Description Recommended Response Action MemRX not enabled or not supported. Servers UEFI: Power down system and reseat DIMMS. Retry test and if no error occurs it was a DIMM connection issue. Client LEGACY: Power down system and re-seat DIMMS. Retry test and if no error occurs it was a DIMM connection issue. Check for latest BIOS.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0125 Message The event log indicates degraded or disabled ECC functionality. Memory testing cannot continue until the problems are corrected, the log cleared and the system rebooted. Detailed Description IPMI System Event Log is full for various reasons or logging has stopped because too many ECC errors have occurred.
Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0131 Message Battery - The battery is not installed. Detailed Description Recommended Response Action Install the battery but check for debris or damaged contacts.
Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0133 Message Battery - The battery cannot provide sufficient power. Detailed Description Recommended Response Action Check battery contacts, plugs and cables. May need to replace battery.
Recommended Response Action Hard drives are not required on all systems so this message is usually a warning. Desktops and Servers: If the system has a hard disk, power down system and check the signal and power connections to it. Rerun the diagnostic.If no error occurs then it was a cable or connector issue. Category Storage Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable DIAG0143 Message Arguments Detailed Description Hard Drive arg1 - SMART read command unsuccessful. • arg1 = Drive Location Mainly seen with very old hard drives Recommended Response Action Category Storage Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0145 Message Arguments Hard Drive arg1 - S/N arg2 , self test did not complete. • arg1 = Drive Location • arg2 = Serial Number Detailed Description Recommended Response Action Desktops and Servers: Power down the system and check the signal and power connections to the hard drive. Rerun the diagnostic.
Detailed Description Prior failure checking removed, is now obsolete. Recommended Response Action Category Storage Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0147 Message Arguments Optical Drive arg1 - Self test: arg2 .
Server Administrator Trap ID Not Applicable DIAG0148 Message Arguments Hard/Optical Drive arg1 - incorrect status: arg2 arg3 . • arg1 = Nth Drive • arg2 = Hex • arg3 = Error Reason Detailed Description Recommended Response Action Category Storage Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0150 Message Hard Drive - No Hard Drive detected, or disk controller not supported.
Detailed Description Recommended Response Action SMART Predictive Failure indicates the hard drive has failed SMART and maybe nearing the end of its life. Other types of in this category may indicate an intermittent or firmware problem, rerun the test again. Desktops, servers: Check the hard disk drive cables and connections. All systems: If error persists, make sure that hard disk drive firmware and BIOS are current. The <80000000000000??> value is an EFI error code returned by the driver.
Server Administrator Trap ID Not Applicable DIAG0154 Message Arguments Tape Drive arg1 - S/N arg2 , incorrect status = arg3 \n arg4 . • arg1 = Drive Location • arg2 = Serial Number • arg3 = 80000000000000?? • arg4 = Error Reason Detailed Description Recommended Response Action Check installation of the tape drive, cables and connections. If the error persists, ensure that drive firmware is current.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0212 Message Arguments System board - CMOS, Location = arg1 h, Expected = arg2 h, Found = arg3 h. • arg1 = Hex • arg2 = Hex • arg3 = Hex Detailed Description Recommended Response Action Make sure that the system is running with the latest BIOS and rerun the diagnostics.
Recommended Response Action Replace the CMOS battery and retry the diagnostic. If the error persists, make sure the BIOS is current and retry the diagnostics. Category System Health Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0221 Message System board - Interval timer not functional.
Detailed Description Recommended Response Action Category System Health Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0233 Message System board - RTC seconds count is not updating. Detailed Description Recommended Response Action Make sure the BIOS is current and retry the diagnostics.
DIAG0234 Message Arguments System board - HPET arg1 , incorrect time period. Expected = arg2 , Found = arg3 . • arg1 = 1 • arg2 = Decimal • arg3 = Decimal Detailed Description Recommended Response Action Make sure the BIOS is current and retry the diagnostics. Category System Health Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0241 Message BIOS - A20 gate not enabled. Detailed Description Recommended Response Action Make sure the BIOS is current and retry the diagnostics. Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Category System Health Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0243 Message USB controller error. Detailed Description Recommended Response Action Ensure that USB ports are intact, contain no failed device and that BIOS is current. After corrective action, rerun the diagnostics.
Recommended Response Action Ensure that the USB device is correctly inserted or try another USB port or device. After corrective action, rerun the diagnostics. If the problem persists, ensure that BIOS is current. Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description Recommended Response Action This is normally a warning message indicating that the Event Log has not been checked lately. The Event Log provides various BIOS and Diagnostic events. Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined.
DIAG0314 Message Arguments Thermal: The ( arg1 ) reading ( arg2 C) exceeds the thermal limit. • arg1 = Sensor Name • arg2 = Degrees Detailed Description Recommended Response Action Check the event log for thermal events, including defective fans and defective sensors. Inspect the system for clogged or obstructed air vents. Make sure that the BIOS is current and rerun the diagnostics.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0321 Message LCD EDID - Unable to access EDID EEPROM. Detailed Description Recommended Response Action This could relate to the LCD connector and cables. Otherwise, flash the latest BIOS and retry diagnostics. Category System Health Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0323 Message Unable to detect inverter lamp status. Detailed Description Recommended Response Action Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0325 Message LCD panel - User provided no input for LCD BIST. Detailed Description Recommended Response Action Possible user error, make sure that the BIOS is current and retry diagnostics.
Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0327 Message LCD panel - Unable to use BIOS interface. Detailed Description Recommended Response Action Make sure that the BIOS is current and retry diagnostics.
Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0331 Message Video controller - No video controller detected. Detailed Description Recommended Response Action Make sure that the BIOS is current and retry diagnostics.
Recommended Response Action Make sure that the BIOS is current and retry diagnostics. Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description Recommended Response Action Possible user error. Otherwise, make sure that BIOS is current and retry diagnostics. Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0411 Message Arguments Cables - arg1 not detected.
DIAG0412 Message Arguments Cables - arg1 not detected. • arg1 = AUX LCD Name Detailed Description Recommended Response Action Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0413 Message Arguments Cables - arg1 not detected.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0414 Message Arguments Cables - arg1 not detected. • arg1 = Inverter Name Detailed Description Recommended Response Action Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG0511 Message Arguments Fan - The ( arg1 ) fan failed to respond correctly. • arg1 = Name Detailed Description Recommended Response Action The fan may be faulty, check for obstructions to the fan and vents. Make sure that BIOS is current and retry the diagnostics.
Detailed Description Recommended Response Action Retry the diagnostics; if the problem persists, the fan is faulty. Make sure that the BIOS is current and retry the diagnostics. Category System Health Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable DIAG0621 Message Arguments Network arg1 - Driver version arg2 outdated. Version arg3 or newer required for " arg4 " • arg1 = Number • arg2 = Hex • arg3 = Hex • arg4 = EFI Driver Name Detailed Description Test only warns because UEFI Network Driver is old and has known false failures. Recommended Response Action Update Network firmware.
Recommended Response Action Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG8002 Message Arguments No BIOS support for SMI interface function(ah) arg1 h.;Sensor arg2 exceeded thermal zone arg3 . Peak zone was arg4 .
DIAG8003 Message Fan - Unable to set Manufacturing Mode. Detailed Description Recommended Response Action Should not occur Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG8004 Message Fan - Unable to determine fan speeds.
Server Administrator Trap ID Not Applicable DIAG8005 Message Arguments LCD BIST not supported. or Fan - Fan speed failure. Expected at least arg1 , observed arg2 . • arg1 = RPM • arg2 = RPM Detailed Description Recommended Response Action If LCD BIST error: The LCD BIST may not exist on all systems. Make sure that the BIOS is current and rerun the diagnostics. If Fan speed error: Insure fans are not dirty or obstructed and check for a loose connection.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG8007 Message Arguments Log contains Fan events;Timer expected arg1 observed arg2 . • • arg1 = Decimal arg2 = Decimal Detailed Description Recommended Response Action For "Log contains Fan events", the events are placed in the log by other sources and ePSA is merely reporting them.
Detailed Description Recommended Response Action Software error, should not normally occur in field. Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined.
DIAG800B Message Retrieve vendor ID function error. Detailed Description Recommended Response Action Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG800C Message Arguments Get/Set inverter mode function error. Vendor: arg1 Revision: arg2 .
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG800D Message Arguments Set lamp off function error. Vendor: arg1 Revision: arg2 . • arg1 = Name • arg2 = Decimal Detailed Description Recommended Response Action Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Recommended Response Action Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG800F Message Arguments Restore function error. Vendor: arg1 Revision: arg2 .
DIAG8010 Message High-Precision event timer not found. Detailed Description Recommended Response Action Software error, should not normally occur in field. Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG8011 Message Invalid status return from the device.
Server Administrator Trap ID Not Applicable DIAG8012 Message Arguments Invalid parameter passed to the device.; Unknown test ( arg1 ) selected. • arg1 = Decimal Detailed Description Recommended Response Action Software error, should not normally occur in field. Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG8014 Message Arguments ADDF module ( arg1 ) device ( arg2 ) failed with error code arg3 , number arg4 . No EPSA beep code mapped. • arg1 = Name • arg2 = Name • arg3 = Hex • arg4 = hex Detailed Description Recommended Response Action Software error, should not normally occur in field.
Recommended Response Action Software error, should not normally occur in field. Category System Health Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG8016 Message Battery - unable to retrieve battery health. Detailed Description Recommended Response Action Software error, should not normally occur in field.
Detailed Description Recommended Response Action Software error, should not normally occur in field. Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined.
DIAG8019 Message Unable to log to NVRAM. Detailed Description Recommended Response Action Software error, should not normally occur in field. Category System Health Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG8020 Message Arguments Low memory.
Server Administrator Trap ID Not Applicable DIAG8021 Message SMBIOS DIMM configuration did not match. Detailed Description Recommended Response Action Software error, should not normally occur in field. Category System Health Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG8155 Message Arguments Tape Drive arg1 - S/N arg2 , data read does not match data written. • • arg1 = Drive Location arg2 = Serial Number Detailed Description Data written the the tape read back differently, not as expected.
Detailed Description Testing requires scratch tape media. Recommended Response Action Install tape media or skip test. Category Storage Subcategory DIAG = Diagnostic Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIAG8157 Message Arguments arg1 Drive arg2 - S/N arg3 , drive is not a supported drive.
Server Administrator Trap ID Not Applicable DIAG8158 Message Arguments arg1 Drive arg2 - S/N arg3 , incorrect status = arg4 \n arg5 . • arg1 = Backplane|Expander|RD1000 • arg2 = Drive Location • arg3 = Serial Number • arg4 = 80000000000000?? • arg5 = Error Reason Detailed Description A device failed a command and testing cannot complete. Recommended Response Action Retry test. If failure persists and BIOS is up to date, a hardware problem is indicated.
Recommended Response Action "If is (Battery missing or disconnected) then check the battery cable to the PERC controller. If is (Replace battery pack) then replace battery pack. If is (Remaining capacity low) then battery pack may need to be replaced soon." Category Storage Subcategory DIAG = Diagnostic Severity Severity 2 (Warning) LCD Message No LCD message display defined.
DIAG8170 Message Arguments PCIe - Training error PciTag- arg1 VendorID- arg2 DeviceID- arg3 SVid- arg4 SDidarg5 Bus arg6 : Link Degraded, maxLinkWidth = x arg7 , negotiatedLinkWidth = x arg8 , Slot arg9 • arg1 = tag • arg2 = hex • arg3 = hex • arg4 = hex • arg5 = hex • arg6 = decimal • arg7 = decimal • arg8 = decimal • arg9 = slot Detailed Description A PCI device is functioning at a lower performance that it should be.
Detailed Description A PCI adapter was detected as present but it does not respond to PCI Configuration Space access, so is very sick or not inserted sungly in the PCI physical slot connector Recommended Response Action Reseat or replace PCI adapter in the PCI slot indicated Category System Health Subcategory DIAG = Diagnostic Severity Severity 1 (Critical) LCD Message No LCD message display defined.
DIS Event Messages 15 DIS001 Message Auto Discovery feature not licensed. Detailed Description Auto Discovery starts automatically, but was unable to find a valid license. Once you have obtained a valid license and installed it, restart. Recommended Response Action Follow service providers instructions to enable the license. Category Configuration Subcategory DIS = Auto-Discovery Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS003 Message Auto Discovery process started. Detailed Description Auto Discovery process will try to connect to a Provisioning Server over the next 24 hours. Recommended Response Action No response action is required. Category Configuration Subcategory DIS = Auto-Discovery Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS005 Message Arguments Auto Discovery communicated successfully with Provisioning Server arg1 . • arg1 = provisioning server name Detailed Description Message was sent successfully from Auto Discovery to Provisioning Server to request certificate.
Category Configuration Subcategory DIS = Auto-Discovery Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS007 Message Unable to notify Provisioning Server of iDRAC IP address change. Detailed Description Unable to connect to Provisioning Server to notify about new iDRAC IP .
Detailed Description iDRAC IP address change in progress with Provisioning Server. Recommended Response Action No response action is required. Category Configuration Subcategory DIS = Auto-Discovery Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS009 Message Arguments Notification of iDRAC IP address changed to arg1 sent to Provisioning Server.
DIS010 Message Arguments Auto Discovery LCD display message: arg1 • arg1 = progress message Detailed Description The Auto Discovery process has encountered a problem.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS012 Message Auto Discovery client using factory signed client certificate. Detailed Description Factory signed client certificate is being used. Auto Discovery client is using this certificate for the SSL connection with the Provisioning Server. Recommended Response Action No response action is required.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS014 Message Auto Discovery client using customer provided CA certificate to authenticate Provisioning Server. Detailed Description Auto Discovery client is using the customer provided Certificate Authority certificate to authenticate the Provisioning Server for the SSL connection.
Category Configuration Subcategory DIS = Auto-Discovery Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS016 Message Response received from Provisioning Server to the notification of iDRAC IP address change. Detailed Description Provisioning Server responded to iDRAC IP address change. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Configuration Subcategory DIS = Auto-Discovery Severity Severity 3 (Informational) Trap/EventID 10635 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS101 Message The execution of AutoConfig operation is started.
DIS102 Message Unable to start the AutoConfig import operation, because the AutoConfig import file is not available. Detailed Description The AutoConfig configuration import operation could not be started, because the AutoConfig .xml file is not available in the sharename or location specified in the DHCP scope option field where the VendorID=iDRAC.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS104 Message The AutoConfig operation is unable to access the network share folder, because an invalid filename is specified in the DHCP scope option field where the VendorID=iDRAC. Detailed Description The AutoConfig operation is unable to access the network share folder, because an invalid filename is specified in the DHCP scope option field where the VendorID=iDRAC.
Recommended Response Action Enter a valid sharetype in DHCP scope option field where the VendorID=iDRAC using (-s <0 or 1>) where 0 = NFS, 1 = CIFS. Category Configuration Subcategory DIS = Auto-Discovery Severity Severity 3 (Informational) Trap/EventID 10635 LCD Message No LCD message display defined.
DIS107 Message Unable to start the AutoConfig file import operation, because an invalid AutoConfig time-to-wait value is specified in the DHCP scope option field where the VendorID=iDRAC. Detailed Description Unable to start the AutoConfig file import operation, because an invalid AutoConfig time-to-wait value is specified in the DHCP scope option field where the VendorID=iDRAC.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DIS109 Message Unable to start the AutoConfig file import operation, because an invalid End Host Power State value is specified in the DHCP scope option field where the VendorID=iDRAC. Detailed Description The server could not be configured because the End Host Power State value specified in the DHCP scope option field where the VendorID=iDRAC is incorrect.
Subcategory DIS = Auto-Discovery Severity Severity 3 (Informational) Trap/EventID 10635 LCD Message No LCD message display defined.
DKM Event Messages DKM0001 Message Arguments arg1 key added for slot arg2 of user arg3 . • arg1 = Security_Key • arg2 = Slot_num • arg3 = Username Detailed Description %s key added for slot %d of user %d. Recommended Response Action No response action is required. Category Audit Subcategory DKM = Dell Key Mngr Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Detailed Description %s key add failed for slot %d of user %d, due to %s. Recommended Response Action No response action is required. Category Audit Subcategory DKM = Dell Key Mngr Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DKM0003 Message Arguments arg1 key deleted for slot arg2 of user arg3 .
Server Administrator Trap ID Not Applicable DKM0004 Message Arguments DKM Error Code arg1 : arg2 error. • arg1 = Error_code_name • arg2 = Error_code_msg Detailed Description DKM Error Code %d: %s error. Recommended Response Action Check the iDRAC User Guide for additional information. Category Audit Subcategory DKM = Dell Key Mngr Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DKM1001 Message The key management service is operating correctly. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory DKM = Dell Key Mngr Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable DKM1004 Message The key management server received a bad request. Detailed Description None Recommended Response Action Check for network connectivity. Review network, server, and client configuration. Category System Health Subcategory DKM = Dell Key Mngr Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Severity Severity 1 (Critical) LCD Message Key management server error.
ENC Event Messages 17 ENC1 Message Arguments arg1 was inserted. • arg1 = Enclosure Management Module Name Detailed Description An Enclosure Management Module (EMM) has failed is inserted into the enclosure. Recommended Response Action No response action is required. Category Storage Subcategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined.
Category Storage Subcategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2152 Server Administrator Trap ID 85100 ENC100 Message Arguments arg1 is sending inconsistent reponses to the controller.
ENC11 Message Arguments The arg1 service tag was changed. • arg1 = enclosure name Detailed Description An enclosure service tag was changed. In most circumstances, this service tag should only be changed by the service provider. Recommended Response Action Make sure that the service tag was changed under authorized circumstances. Category Storage Subcategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2162 Server Administrator Trap ID 85100 ENC13 Message Arguments Unsupported configuration detected on arg1 . arg2 arg3 • arg1 = Enclosure Name • arg2 = EMM0 1 • arg3 = EMM1 2 Detailed Description An unsupported configuration was detected. The SCSI rate of the Enclosure Management Modules (EMMs) are not the same.
Detailed Description There are too many enclosures attached to the controller port. When the enclosure limit is exceeded, the controller loses contact with all enclosures attached to the port. This is an unsupported configuration. Recommended Response Action Remove the extra enclosures. Refer to the storage hardware documentation for maximum number of enclosures that can be connected.
Server Administrator Trap ID 85100 ENC16 Message Arguments An enclosure blink has ceased on arg1 . • arg1 = Enclosure Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2291 Server Administrator Trap ID 85100 ENC18 Message Arguments Communication with arg1 was lost. • arg1 = enclosure name Detailed Description The controller has lost communication with an Enclosure Management Module (EMM). The cables may be loose or defective. Recommended Response Action Make sure the cables are attached securely.
Detailed Description An Enclosure Management Module (EMM) has failed. The failure may be caused by a loss of power to the EMM. The EMM self-test may also have identified a failure. There may also be a firmware problem or a multi-bit error. Recommended Response Action Reseat the Enclosure Management Module (EMM). See the storage hardware documentation for information on replacing the EMM. Replace the EMM. Contact technical support if the issue persists.
Server Administrator Trap ID 95400 ENC21 Message Arguments arg1 has been removed. • arg1 = Enclosure elements name Detailed Description A device has been removed and the system is no longer functioning in optimal condition. Recommended Response Action Replace the device. Category Storage Subcategory ENC = Storage Enclosr Severity Severity 1 (Critical) Trap/EventID 4337 LCD Message No LCD message display defined.
Subcategory ENC = Storage Enclosr Severity Severity 2 (Warning) Trap/EventID 4338 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2298 Server Administrator Trap ID 85300 ENC23 Message Arguments arg1 - Issue with PHY arg2 . • arg1 = enclosure name • arg2 = PHY data Detailed Description There is a problem with a physical connection or PHY in the enclosure idenfiied in the message. Recommended Response Action Contact your service provider.
Arguments • arg1 = enclosure name Detailed Description The controller is not receiving a consistent response from the enclosure. There could be a firmware problem or an invalid cabling configuration. If the cables are too long, they degrade the signal. Recommended Response Action Power down all enclosures attached to the system and reboot . If the problem persists, upgrade the firmware to the latest supported version. Verify the cable configuration is valid.
Server Administrator Event ID 2301 Server Administrator Trap ID 85400 ENC26 Message Arguments arg1 is not responding. • arg1 = enclosure name Detailed Description The enclosure or an enclosure component is in a Failed or Degraded state. It is not responding to storage management commands or there is a connectivity problem between the controller and enclosure. Recommended Response Action Verify the health of the enclosure and its components. See the hardware documentation to for more information.
Recommended Response Action No response action is required. Category Storage Subcategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2303 Server Administrator Trap ID 85100 ENC28 Message Arguments Enclosure Management Module (EMM) firmware version mismatch detected in arg1 . arg2 arg3 .
Server Administrator Event ID 2311 Server Administrator Trap ID 85300 ENC29 Message Arguments arg1 temperature has returned to normal. • arg1 = Enclosure Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined.
too hot or too cold. Refer to the enclosure documentation for more diagnostic information. Category Storage Subcategory ENC = Storage Enclosr Severity Severity 1 (Critical) Trap/EventID 4337 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2112 Server Administrator Trap ID 85400 ENC30 Message Arguments arg1 firmware download is in-progress. • arg1 = Enclosure Name Detailed Description This alert is provided for informational purposes.
ENC31 Message Arguments Firmware download on arg1 has failed. • arg1 = Enclosure Name Detailed Description The system was unable to download firmware to the enclosure. The controller may have lost communication with the enclosure. There may have been problems with the data transfer or the download media may be corrupt. Recommended Response Action Attempt to download the enclosure firmware again. If problems continue, verify that the controller can communicate with the enclosure.
Trap/EventID 4339 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2368 Server Administrator Trap ID 85100 ENC33 Message Arguments Redundancy on arg1 is normal. • arg1 = Enclosure Name Detailed Description Data redundancy has been restored to an enclosure that previously suffered a loss of redundancy. Recommended Response Action This alert is provided for informational purposes.
Detailed Description The firmware on the EMM modules is not the same version. It is required that both modules have the same version of the firmware. This alert may be caused when you attempt to insert an EMM module that has a different firmware version than an existing module. Recommended Response Action Download the same version of the firmware to both EMM modules.
Server Administrator Event ID 2190 Server Administrator Trap ID 75100 ENC5 Message Arguments Redundancy on arg1 is degraded • arg1 = Enclosure Name Detailed Description One or more of the enclosure components has failed. For example, a fan or power supply may have failed. Although the enclosure is currently operational, the failure of additional components could cause the enclosure to fail. Recommended Response Action Identify and replace the failed component.
Detailed Description The controller is unable to communicate with an enclosure. There are several reasons for communication loss. For example, there may be a bad or loose cable. An unusual amount of I/O may also interrupt communication with the enclosure. In addition, communication loss may be caused by software, hardware, or firmware problems, bad or failed power supplies, and enclosure shutdown. Recommended Response Action Check for problems with the cables.
Initial Default LC Log Server Administrator Event ID 2138 Server Administrator Trap ID 85100 ENC8 Message Arguments The arg1 alarm was disabled. • arg1 = Enclosure Name Detailed Description You have disabled the enclosure alarm. Recommended Response Action No response action is required. Category Storage Subcategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined.
Recommended Response Action No response action is required. Category Storage Subcategory ENC = Storage Enclosr Severity Severity 3 (Informational) Trap/EventID 4339 LCD Message No LCD message display defined.
FAN Event Messages 18 FAN0000 Message Arguments Fan arg1 RPM is less than the lower warning threshold. • arg1 = number Detailed Description The fan is not performing optimally. The fan may be installed improperly or may be failing. Recommended Response Action Remove and re-install the fan at the next scheduled service window. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Category System Health Subcategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 2153 LCD Message Fan RPM is outside of range. Check fan. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN0002 Message Arguments Fan arg1 RPM is greater than the upper warning threshold. • arg1 = number Detailed Description The fan is not performing optimally.
Arguments • arg1 = number Detailed Description The fan is not performing optimally. The fan may be installed improperly or may be failing. Recommended Response Action Remove and re-install the fan. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 2153 LCD Message Fan RPM is outside of range. Check fan.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN0005 Message Arguments Fan arg1 RPM is within range. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory FAN = Fan Event Severity Severity 3 (Informational) Trap/EventID 2155 LCD Message No LCD message display defined.
Category System Health Subcategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 2153 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN0007 Message Arguments Fan arg1 was inserted. • arg1 = number Detailed Description None Recommended Response Action No response action is required.
Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory FAN = Fan Event Severity Severity 3 (Informational) Trap/EventID 2155 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN0009 Message Arguments Fan arg1 is absent.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN0010 Message Arguments Fan arg1 is disabled. • arg1 = number Detailed Description The fan may be required for optimal performance. Recommended Response Action No response action is required. Category System Health Subcategory FAN = Fan Event Severity Severity 2 (Warning) Trap/EventID 2154 LCD Message No LCD message display defined.
Category System Health Subcategory FAN = Fan Event Severity Severity 3 (Informational) Trap/EventID 2155 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN0012 Message Arguments arg1 RPM is less than the lower warning threshold. • arg1 = fan name Detailed Description The device is not performing optimally. The device may be installed improperly.
Arguments • arg1 = fan name Detailed Description The cooling device is not performing optimally. The cooling device may be installed improperly. Recommended Response Action Remove and re-install the cooling device. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 2153 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN0015 Message Arguments arg1 RPM is greater than the upper critical threshold. • arg1 = fan name Detailed Description The cooling device is not performing optimally. The cooling device may be installed improperly. Recommended Response Action Remove and re-install the cooling device. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Category System Health Subcategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 2153 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN0017 Message Arguments arg1 RPM is within normal operating range. • arg1 = fan name Detailed Description The RPM of the fan identified in the message is functioning correctly.
Arguments • arg1 = fan number Detailed Description Enhanced Cooling Mode is not supported by the type of fan identified in the message. Recommended Response Action Replace the fan identified in the message with another fan which supports Enhanced Cooling Mode. Category System Health Subcategory FAN = Fan Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable FAN0020 Message Arguments The arg1 is non-functional. • arg1 = fan name Detailed Description The fan identified in the message has failed or it is not installed correctly. Recommended Response Action Remove and re-install the fan or replace the fan, and open the OMSA Web interface to verify if the fan specified in the message is displayed correctly. If the issue persists, contact your service provider.
LCD Message No LCD message display defined. Initial Default OS Log;None Server Administrator Event ID 5303 Server Administrator Trap ID Not Applicable FAN0022 Message Arguments The arg1 sensor has failed, and the last recorded value by the sensor was arg2 RPM. • arg1 = sensor name • arg2 = fan speed Detailed Description The sensor identified in the message has failed. The sensor may be required for optimal system performance.
Recommended Response Action Do the following: 1) Remove the old fan, install a new fan and power cycle the system to check if the fan is working properly, 2) Replace the system board if the fan sensor has failed. 3) If the issue persists, contact your service provider. Category System Health Subcategory FAN = Fan Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
FAN0025 Message Arguments The arg1 sensor state has changed to a warning state with a value of arg2 RPM. • arg1 = sensor name • arg2 = fan speed Detailed Description The fan identified in the message is not functioning correctly. The fan may be installed incorrectly or may be failing. Recommended Response Action Remove and re-install the fan, or replace the fan. If the issue persists, contact your service provider.
Initial Default SNMP Alert;OS Log;None Server Administrator Event ID 5104 Server Administrator Trap ID 5104 FAN0027 Message Arguments The arg1 sensor has failed with a value of arg2 RPM. • arg1 = sensor name • arg2 = fan speed Detailed Description The sensor identified in the message has failed. The sensor may be required for optimal system performance. Recommended Response Action Check the Embedded System Management (ESM) Log for any sensor related faults.
Recommended Response Action Re-insert the fan into the enclosure. Contact technical support if the issue persists. Category Storage Subcategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 4201 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN1001 Message Arguments arg1 has been inserted.
FAN1002 Message Arguments arg1 has failed. • arg1 = Fan Sensor Name Detailed Description The enclosure detected that a fan has failed and the enclosure is no longer functioning in optimal condition.. Recommended Response Action Contact technical support. Category Storage Subcategory FAN = Fan Event Severity Severity 1 (Critical) Trap/EventID 4201 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN8501 Message Enhanced Cooling Mode is Disabled Detailed Description Disabling Enhanced Cooling Mode allows for reduced power consumption by reducing the maximum speed of the blowers while still providing sufficient blade airflow. Recommended Response Action No response action is required.
Subcategory FAN = Fan Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN8503 Message Chassis was turned off because more than two internal fans stopped functioning properly. Detailed Description The Chassis was turned off because more than two Chassis internal fans stopped functioning properly.
Recommended Response Action No response action required. Category Configuration Subcategory FAN = Fan Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN901 Message The Enhanced Cooling Mode is successfully disabled. Detailed Description The Enhanced Cooling Mode is successfully disabled. Recommended Response Action No response action required.
Detailed Description The Enhanced Cooling Mode cannot be set because required power is not available. Recommended Response Action Add PSUs with higher power capability or remove Chassis components such as I/O Modules orservers until the power requirements have been lowered enough to emable the Enhanced Cooling Mode, and then retry the operation. Category Configuration Subcategory FAN = Fan Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
FAN904 Message Cannot enable the Enhanced Cooling Mode because the Maximum Power Conservation Mode is enabled. Detailed Description The Enhanced Cooling Mode cannot be enabled because the Maximum Power Conservation Mode is enabled. Recommended Response Action Disable the Maximum Power Conservation Mode, and then retry the operation. To disable the mode by using CMC Web interface, click Chassis Overview > Power > Configuration.
Server Administrator Trap ID Not Applicable FAN906 Message Changes are not made to the current settings. Detailed Description Changes are not made to the current settings. Recommended Response Action Make sure that changes are made to the settings and retry the operation. Category Configuration Subcategory FAN = Fan Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FAN908 Message The Enhanced Cooling Mode feature is already disabled. Detailed Description The Enhanced Cooling Mode feature is already disabled. Recommended Response Action No response action required. Category Configuration Subcategory FAN = Fan Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable 480
FC Event Messages 19 FC001 Message The command was successful. Detailed Description The command was successful. Recommended Response Action No response action is required. Category Configuration Subcategory FC = Fiber Channel Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FC002 Message Unable to allocate memory.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FC003 Message Missing required parameter. Detailed Description An invalid number of arguments was provided to the method. Recommended Response Action Enter required input parameters and retry. For more information, see Lifecycle Controller Users Guide or the FC HBA Profile specification.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FC005 Message The number of AttributeName array elements does not match the AttributeValue array element count. Detailed Description The number of AttributeName and AttributeValue array elements are not equal.
Category Configuration Subcategory FC = Fiber Channel Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FC007 Message A configuration job already exists. Unable to create another configuration job on specified target until existing job is completed or is cancelled. Detailed Description Configuration job already created on the specified target.
Recommended Response Action Change the configuration of one or more attributes and retry creating the Configuration job. Category Configuration Subcategory FC = Fiber Channel Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FC009 Message Lifecycle Controller is currently in use.
Detailed Description For 11G systems: System Services must be enabled to perform the requested operation. System Services has been disabled through the iDRAC configuration utility accessed by pressing CTRL+E on boot up or through a remote operation. For 12G systems: Lifecycle Controller must be enabled to perform the requested operation.
Server Administrator Trap ID Not Applicable FC012 Message No pending data to delete. Detailed Description No changes to component attribute data are available between the previous configuration and the current configuration. Recommended Response Action No response action is required. Category Configuration Subcategory FC = Fiber Channel Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FC014 Message Arguments Invalid AttributeValue parameter content for corresponding AttributeName arg1 .
Recommended Response Action No response action is required. Category Configuration Subcategory FC = Fiber Channel Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FC016 Message Arguments Unable to change the attribute value of the disabled attribute arg1 .
FC017 Message Unable to perform the operation due to an internal error in iDRAC. Detailed Description An internal error occurred in iDRAC and the operation cannot continue. An iDRAC reset is required to recover from the error. Recommended Response Action Disconnect the AC power source from the system, reconnect the power source, and retry the operation. Category Configuration Subcategory FC = Fiber Channel Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default SNMP Alert;EMAIL Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable FC103 Message Arguments The FC arg1 port arg2 network connection is successfully started. • arg1 = controller ID • arg2 = port ID Detailed Description The network connection of the FC controller port link identified in the message is successfully started. Recommended Response Action No response action required.
FLDC Event Messages 20 FLDC1001 Message Arguments The journal mirror at path = arg1 is available. • arg1 = World Wide Name Detailed Description The entry in the journal for the device identified in the message with the WWN (World Wide Name) is available. Recommended Response Action No response action is required. Category Storage Subcategory FLDC = Unknown Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory FLDC = Unknown Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2701 Server Administrator Trap ID 160100 FLDC1003 Message Arguments Cache flushing has started for the virtual disk with WWN = arg1 and path = arg2 . • arg1 = World Wide Name • arg2 = device pathname Detailed Description The cache flushing operation has started for the virtual disk identified in the message.
• arg2 = device pathname Detailed Description The cache flushing operation has completed for the virtual disk identified in the message. Recommended Response Action No response action is required. Category Storage Subcategory FLDC = Unknown Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID 90100 FLDC1007 Message Arguments The cache device arg1 with WWN = arg2 and path = arg3 is removed. • arg1 = physical disk Name • arg2 = World Wide Name • arg3 = device pathname Detailed Description The cache device identified in the message is removed from the Fluid Cache configuration. Recommended Response Action No response action is required.
Category Storage Subcategory FLDC = Unknown Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2905 Server Administrator Trap ID 90100 FLDC1009 Message Arguments Caching is being removed for the arg1 with WWN = arg2 and path = arg3 . • arg1 = virtual disk name • arg2 = World Wide Name • arg3 = device pathname Detailed Description Caching is being removed for the virtual disk identified in the message.
Arguments • arg1 = virtual disk name • arg2 = World Wide Name • arg3 = device pathname Detailed Description Caching is enabled on the virtual disk identified in the message. Recommended Response Action No response action is required. Category Storage Subcategory FLDC = Unknown Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID 2910 Server Administrator Trap ID 120100;150100;160100 FLDC1013 Message Arguments The cached LUN with WWN = arg1 and path = arg2 for arg3 has had a failure. • arg1 = World Wide Name • arg2 = device pathname • arg3 = virtual disk name Detailed Description The cached LUN identified in the message has had a failure to successfully perform a read or write operation.
Detailed Description Replication of the cache device identified in the message is complete. Recommended Response Action No response action is required. Category Storage Subcategory FLDC = Unknown Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2912 Server Administrator Trap ID 90100 FLDC1015 Message Arguments Recovery of the cache device arg1 with wwn = arg2 and path = arg3 is complete.
Server Administrator Trap ID 90100 FLDC1016 Message A valid permanent license is installed for Fluid Cache. Detailed Description A valid permanent license is installed for Fluid Cache. Recommended Response Action No response action is required. Category Storage Subcategory FLDC = Unknown Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID 2920 Server Administrator Trap ID 160100 FLDC1018 Message A license has been removed for Fluid Cache. Detailed Description A license has been removed for Fluid Cache. Recommended Response Action No response action is required. Category Storage Subcategory FLDC = Unknown Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID 2924 Server Administrator Trap ID 160100 FLDC1020 Message Arguments The storage device with WWN = arg1 and path = arg2 is in unknown state. • arg1 = wwn name • arg2 = path name Detailed Description The storage device identified in the message is in unknown state. Recommended Response Action Service is required. Contact your service provider.
the journal mirrors, then this event is signaled. It is a warning because the FLDC code will then attempt to choose another SSD to be a journal mirror. Recommended Response Action No response action is required.. Category Storage Subcategory FLDC = Unknown Severity Severity 2 (Warning) LCD Message No LCD message display defined.
FLDC1023 Message Arguments Fluid Cache is running on an evaluation license and the evaluation license expires in arg1 days. • arg1 = days Detailed Description Fluid Cache is currently running on an evaluation license and the evaluation license expires in the number of days identified in message. Recommended Response Action A permanent license for Fluid Cache should be purchased for continued service.
Server Administrator Event ID 2930 Server Administrator Trap ID 120300;150300;160300 FLDC1025 Message Caching was enabled in write-back or write-through mode, it is currently operating in pass-through mode. Detailed Description Caching was enabled in write-back mode or write through mode, but currently it is operating in write-through mode because fluid Cache Pool has no PCIe-SSD device. Recommended Response Action Add another PCIe SSD device to the Fluid Cache Pool to resolve the issue.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2932 Server Administrator Trap ID 120300;150300;160300 FLDC1027 Message Caching is no longer degraded to pass-through mode and is now operating in its configured mode for Fluid Cache. Detailed Description The caching mode has been restored back to the configured mode due to the availability of additional PCIeSSD devices in the Fluid Cache configuration.
Category Storage Subcategory FLDC = Unknown Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2699 Server Administrator Trap ID 160400 FLDC1029 Message There are not enough journal mirrors available for Fluid Cache to operate. Detailed Description The message indicates that there are not enough journal mirrors available for Fluid Cache to operate.
Recommended Response Action Service is required. Contact your service provider. Category Storage Subcategory FLDC = Unknown Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2704 Server Administrator Trap ID 160400 FLDC1031 Message The journal could not be read or written to for Fluid Cache. Detailed Description Unable to access redundant Fluid Cache configuration information.
• arg2 = path name Detailed Description The PCIeSSD cache device identified in the message is no longer functional. Recommended Response Action Replace the non-functional PCIe SSD. Category Storage Subcategory FLDC = Unknown Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID 120400;150400 FLDC1034 Message A valid license is not installed for Fluid Cache. Detailed Description A valid license is not installed for Fluid Cache. Recommended Response Action Install a valid Fluid Cache license. For more information, contact your service provider. Category Storage Subcategory FLDC = Unknown Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2917 Server Administrator Trap ID 160400 FLDC1036 Message Arguments Caching functionality is disabled because Fluid cache is running on an expired evaluation license (Expired days: arg1 ). • arg1 = number of days Detailed Description Caching functionality is disabled because Fluid cache is running on an expired evaluation license.
Recommended Response Action Install a permanent Fluid Cache license. Category Storage Subcategory FLDC = Unknown Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2919 Server Administrator Trap ID 160400 FLDC1038 Message There is not enough memory capacity to run necessary services for Fluid Cache. Detailed Description There is not enough memory capacity to run necessary services for Fluid Cache.
Detailed Description One or more cache devices are missing and the cache is unresponsive. Recommended Response Action Insert the missing cache device. If the cache device was unplugged, reactivate it. Reactivate a cache device by running the following command: "omconfig storage pciessd action=reactivate subsystem=id pciedevice=" Category Storage Subcategory FLDC = Unknown Severity Severity 1 (Critical) LCD Message No LCD message display defined.
FSD Event Messages 21 FSD000 Message Arguments Debug authorized by customer; debugcaps: arg1 , was authorized by: arg2 , at arg3 for the period: arg4 to arg5 . • arg1 = DebugCaps • arg2 = iDRAC User • arg3 = unblock time • arg4 = start time • arg5 = end time Detailed Description The customer has authorized the specified debug capabilities on this iDRAC. (This should occur in response to a request from Dell tech support.
Arguments • arg1 = DebugCaps • arg2 = grant time • arg3 = Dell employee • arg4 = start time • arg5 = end time Detailed Description Dell has authorized the specified debug capabilities. Each debug capability represents a certain action Dell engineers can perform to debug iDRAC.
Recommended Response Action DebugCaps;IDRAC user;Dell employee;unblock time;start time;end time Category Audit Subcategory FSD = Debug Severity Severity 2 (Warning) Trap/EventID 8594 LCD Message No LCD message display defined.
HWC Event Messages 22 HWC0001 Message Unable to complete the operation as there is no response from iDRAC. Detailed Description The error is caused due to iDRAC failure. Recommended Response Action 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord and turn on the system. Category Configuration Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC0003 Message Successfully initialized vFlash SD card. Detailed Description vFlash SD card was successfully initialized. Recommended Response Action No response action is required. Category Configuration Subcategory HWC = Hardware Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC0005 Message Internal error while retrieving update information. Detailed Description Internal error while retrieving firmware version for the currently installed components. For more information about the failure, see Lifecycle Log. Recommended Response Action 1) Turn off the system and disconnect the power cord.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC0007 Message Unable to load vFlash SD card settings. Detailed Description Lifecycle Controller is unable to retrieve vFlash SD card information from iDRAC. Recommended Response Action Reinsert the vFlash SD card and retry the operation.
Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC0009 Message Unable to enable vFlash SD card. Detailed Description The vFlash SD card is missing or not inserted correctly. iDRAC is not able to enable vFlash SD card. Recommended Response Action Reinsert the vFlash SD card and retry the operation.
Category Configuration Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC0011 Message Insufficient space to copy the file to the USB drive. Detailed Description The USB drive does not have sufficient free space to copy the file.
Recommended Response Action Remove write protection on the USB drive before retrying the operation. Category Configuration Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC0013 Message Unable to copy the file to USB drive. Detailed Description The USB drive is disconnected or is not readable.
Detailed Description The import operation failed because the vFlash SD card is missing or disabled. Recommended Response Action Make sure the vFlash SD card is inserted and enabled before retrying the operation. Category Configuration Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC0015 Message iDRAC not responding.
HWC0016 Message iDRAC communication failure. Detailed Description Lifecycle Controller is unable to communicate with iDRAC. Recommended Response Action Retry the operation. If the problem persists, 1) Turn off the system and disconnect the power cord. 2) Wait five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation. Category Configuration Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC1001 Message Arguments The arg1 is absent. • arg1 = name Detailed Description The absent device may be necessary for proper operation. System functionality may be degraded. Recommended Response Action Re-install or reconnect the hardware. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message The is absent.
Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC1003 Message Arguments The arg1 is enabled. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC1005 Message The storage adapter is absent. Detailed Description The storage adapter may be necessary for proper operation. System functionality may be degraded.
HWC1006 Message The storage adapter is disabled. Detailed Description None Recommended Response Action If adapter disabled unexpectedly, re-enable the storage adapter. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC1007 Message The storage adapter is enabled.
Server Administrator Trap ID Not Applicable HWC1008 Message The backplane is present. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC1009 Message The backplane is absent.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC1010 Message The backplane is disabled. Detailed Description None Recommended Response Action If disabled unexpectedly, re-enable backplane. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC1012 Message The USB cable is present. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message The USB cable is absent. Check cable Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC1014 Message Arguments The mezzanine card arg1 is present. • arg1 = number Detailed Description None Recommended Response Action No response action is required.
Detailed Description The mezzanine card may be necessary for proper operation. System functionality may be degraded. Recommended Response Action If removal was unintended, check presence, then re-install or reconnect. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable HWC1101 Message Arguments The arg1 is removed from slot arg2 . • arg1 = name • arg2 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC1201 Message Arguments The sled arg1 is removed from slot arg2 . • arg1 = sled name • arg2 = slot number Detailed Description The sled identified in the message is removed from the slot identified in the message.
HWC2000 Message Arguments The arg1 cable or interconnect is connected. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
LCD Message The cable or interconnect failure. Check connection Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC2002 Message Arguments The storage arg1 cable or interconnect is connected. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action Check presence, then re-install or reconnect. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message Storage cable or interconnect failure. Check connection Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC2004 Message Arguments The system board arg1 cable or interconnect is connected.
HWC2005 Message Arguments The system board arg1 cable or interconnect is not connected, or is improperly connected. • arg1 = name Detailed Description The cable may be necessary for proper operation. System functionality may be degraded. Recommended Response Action Check presence, then re-install or reconnect. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message System board cable or interconnect failure.
LCD Message is not installed correctly. Check connection Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC2007 Message Arguments The arg1 is installed correctly. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
Recommended Response Action Check chassis fabric type in CMC GUI and compare to the type of IOM or mezzanine card. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC2009 Message Arguments Mezzanine card arg1 is installed correctly.
HWC2010 Message The riser board cable or interconnect is connected. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC2012 Message Arguments A fabric mismatch detected on fabric arg1 with server in slot arg2 . • arg1 = name • arg2 = number Detailed Description The fabric type on the server does not match that of the IO module. Recommended Response Action Check chassis fabric type in CMC GUI and compare to the type of IOM or mezzanine card.
Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC2014 Message Arguments A hardware misconfiguration detected on arg1 . • arg1 = name Detailed Description None.
HWC2015 Message Arguments The arg1 is configured correctly. • arg1 = name Detailed Description None. Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC3000 Message Arguments The arg1 is removed.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC3001 Message Arguments The arg1 is inserted. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
Recommended Response Action If removal was unintended, check presence, then re-insert Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC3003 Message Arguments Server arg1 was inserted.
HWC3004 Message Arguments IO module arg1 is removed. • arg1 = number Detailed Description None Recommended Response Action If removal was unintended, check presence, then re-insert Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC3006 Message Arguments Unable to QuickDeploy server in slot arg1 . • arg1 = slot number Detailed Description There are not enough IPv4 addresses reserved for the servers in this chassis. Therefore the newly inserted server could not be configured with the QuickDeploy feature.
Recommended Response Action Update the BMC/iDRAC firmware. If the problem persists, contact support. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message Incompatibility between BMC/iDRAC firmware and CPU. Update firmware Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC4001 Message A hardware incompatibility was corrected between BMC/iDRAC firmware and CPU.
HWC4002 Message A hardware incompatibility detected between BMC/iDRAC firmware and other hardware. Detailed Description A hardware incompatibility was detected between BMC/iDRAC firmware and other hardware. An iDRAC or BMC firmware update is needed. Recommended Response Action Update the BMC/iDRAC firmware. If the problem persists, contact support.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC4010 Message Arguments Hardware successfully updated for mezzanine card arg1 . • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC4012 Message Hardware successfully updated for embedded NIC. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action Check presence, re-install or reconnect, then re-attempt the update. If the problem persists, contact support. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC4014 Message Link Tuning data successfully updated.
Detailed Description CMC has old firmware and does not recognize the new device which has requested link tuning information. After updating the firmware the CMC will recognize the device. Recommended Response Action Update the CMC firmware. If the problem persists, contact support. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable HWC4017 Message Arguments A hardware incompatibility is detected between arg1 arg2 and arg3 arg4 . • arg1 = first component name • arg2 = first component location • arg3 = second component name • arg4 = second component location Detailed Description The system has detected an unsupported hardware component. A hardware incompatibility is detected between the components identifed in the message.
Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC5000 Message Arguments arg1 is online. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
HWC5001 Message Arguments arg1 is offline. • arg1 = name Detailed Description None Recommended Response Action If unexpected, check presence, then re-install or reconnect. Category System Health Subcategory HWC = Hardware Config Severity Severity 2 (Warning) Trap/EventID 2330 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC5003 Message Arguments arg1 is operating correctly. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
Recommended Response Action Update the CMC firmware. If the problem persists, contact support. Category System Health Subcategory HWC = Hardware Config Severity Severity 2 (Warning) Trap/EventID 2330 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC5006 Message Arguments A failure is detected on arg1 .
HWC5008 Message Arguments Console is not available for the arg1 . • arg1 = name Detailed Description None Recommended Response Action Contact technical support. Refer to your product documentation to choose the contact method that is convenient for you. Category System Health Subcategory HWC = Hardware Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC5012 Message Arguments On screen display (OSCAR) is not functional for the arg1 . • arg1 = name Detailed Description None Recommended Response Action Contact technical support. Refer to your product documentation to choose the contact method that is convenient for you. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC5030 Message Arguments IO module arg1 is online. • arg1 = number Detailed Description None Recommended Response Action No response action is required.
Detailed Description The CMC has powered off the IOM. Recommended Response Action Contact technical support. Refer to your product documentation to choose the contact method that is convenient for you. Category System Health Subcategory HWC = Hardware Config Severity Severity 2 (Warning) Trap/EventID 2330 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable HWC5033 Message Arguments IO module arg1 is operating correctly. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
Severity Severity 2 (Warning) Trap/EventID 2330 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC5035 Message Arguments An over-temperature event detected on I/O module arg1 . • arg1 = number Detailed Description The I/O module over heated. Recommended Response Action Do the following: 1) Make sure fans are installed and working correctly.
Detailed Description The IOM module performance may be impact. Recommended Response Action Contact technical support. Refer to your product documentation to choose the contact method that is convenient for you. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable HWC6000 Message Arguments The arg1 controller is offline. • arg1 = name Detailed Description Information and status from the controller is unavailable. Recommended Response Action Remove and reapply input power. If problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC6002 Message Arguments The arg1 controller is stuck in boot mode. • arg1 = name Detailed Description Information and status from the controller is unavailable. Recommended Response Action Remove and reapply input power. If problem persists, contact technical support.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC6004 Message Arguments Cannot communicate with arg1 controller.
Server Administrator Trap ID Not Applicable HWC6005 Message Arguments Communications restored for arg1 controller. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 2331 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC7002 Message Arguments Server arg1 health changed to a warning state from a normal state. • arg1 = number Detailed Description Server health changed to a warning state from a normal state. Recommended Response Action Review System Log or front panel for additional information.
Detailed Description Server health changed to a critical state from either a normal or warning state. Recommended Response Action Review System Log or front panel for additional information. Category System Health Subcategory HWC = Hardware Config Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable HWC7008 Message Arguments Server arg1 health changed to a warning state from more severe state. • arg1 = number Detailed Description Server health changed to a warning state from more severe state. Recommended Response Action Review System Log or front panel for additional information. Category System Health Subcategory HWC = Hardware Config Severity Severity 2 (Warning) Trap/EventID 2330 LCD Message No LCD message display defined.
Severity Severity 1 (Critical) Trap/EventID 2329 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable HWC7012 Message Arguments Server arg1 health changed to a non-recoverable state. • arg1 = number Detailed Description Server health changed to a non-recoverable state. Recommended Response Action Review System Log or front panel for additional information.
• arg2 = details Detailed Description An unknown device plug event occurred at the identified device location. Along with the device location, additional event details are provided if available. Recommended Response Action No response action is required. Category Audit Subcategory HWC = Hardware Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID 5651 HWC8002 Message Arguments The device was removed from the system at this location: arg1 . Additional Details: arg2 . • arg1 = device location • arg2 = details Detailed Description A device was was removed from the system at the location identified in the message. Along with the device location, additional event details are provided if available. Recommended Response Action No response action is required.
Recommended Response Action Reinsert the device or try inserting a different device of the same type and retry the operation. If the issue persists, check the system documentation to make sure the device is supported or contact your service provider. Category Audit Subcategory HWC = Hardware Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable HWC8005 Message Arguments The SD card device has returned to normal state. SD card location: arg1 , SD card device type: arg2 , SD card state: arg3 . • arg1 = location • arg2 = type • arg3 = state Detailed Description The SD card device has returned to a normal state. The SD card type and the current status of the SD card is also displayed. Recommended Response Action No response action is required.
Recommended Response Action Reinsert the SD card or try a different SD card and retry the operation. If the issue persists, do one of the following to resolve the error: 1) If the SD card sensor is installed on the internal SD module, replace the module. 2) If the SD card sensor is embedded on the system board, replace the system board. . For more information, contact your service provider.
Server Administrator Trap ID 5754 HWC8008 Message Arguments The SD card has failed. SD card location: arg1 , SD card device type: arg2 , SD card state: arg3 . • arg1 = location • arg2 = type • arg3 = state Detailed Description An SD card device sensor has detected an irrecoverable error in the SD card. Recommended Response Action Replace the old SD card with a new SD card.
Recommended Response Action Remove and reinsert the identified SD card. Category System Health Subcategory HWC = Hardware Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
IOID Event Messages 23 IOID001 Message The Input/Output Identity (I/O Identity) optimization feature is enabled. Detailed Description After the I/O Identity optimization feature is enabled, the time during boot to configure I/O Identity attributes using the Server Configuration Profile (Configuration XML) import feature will be significantly reduced. Recommended Response Action No response action required.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable IOID003 Message Arguments The Virtual Address Persistence Policy setting for Auxiliary powered devices is changed to arg1 . • arg1 = restart type Detailed Description The Virtual Address Persistence Policy setting for Auxiliary powered devices is changed to the restart type identified in the message.
Recommended Response Action No response action is required. Category Configuration Subcategory IOID = IO Identity Optimization Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable IOID005 Message Arguments Storage Initiator Persistence Policy setting is changed to arg1 .
IOID006 Message Arguments Storage Target Persistence Policy setting is changed to arg1 . • arg1 = restart type Detailed Description The Storage Target Persistence Policy setting is changed to the restart type identified in the message. Recommended Response Action No response action is required. Category Configuration Subcategory IOID = IO Identity Optimization Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default SNMP Alert;EMAIL Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable IOID111 Message Arguments Unable to configure the virtual address of NIC arg1 Port arg2 . • arg1 = controller • arg2 = port Detailed Description The virtual address of the NIC port identified in the message could not be successfully configured because either the network port connection is not enabled or the NIC is not capable of Virtual Addressing.
Detailed Description The initiator properties of the NIC port identified in the message are successfully configured. Recommended Response Action No response action is required. Category Configuration Subcategory IOID = IO Identity Optimization Severity Severity 3 (Informational) Trap/EventID 10771 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable IOID114 Message Arguments The target settings properties of the NIC arg1 Port arg2 are successfully configured. • arg1 = controller • arg2 = port Detailed Description The target setting properties of the NIC port identified in the message are successfully configured. Recommended Response Action No response action is required.
Category Configuration Subcategory IOID = IO Identity Optimization Severity Severity 2 (Warning) Trap/EventID 10770 LCD Message No LCD message display defined. Initial Default SNMP Alert;EMAIL Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable IOID116 Message Applying I/O Identity settings based on current persistence policy settings.
Detailed Description The iDRAC has applied I/O Identity settings on NIC and FC HBA devices. All the device configuration related to virtual addresses, initiator and target settings have been configured successfully according to the current persistence policy settings. Recommended Response Action No response action is required. Category Configuration Subcategory IOID = IO Identity Optimization Severity Severity 3 (Informational) Trap/EventID 10771 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable IOID119 Message FlexAddress is enabled on all NIC and FC HBA devices. Detailed Description The FlexAddress feature is enabled on the system. The iDRAC will assign FlexAddress defined MAC and WWN values to all the ports and/or partitions of bNDCs and mezzanine adapters of the system. Recommended Response Action No response action is required.
IOV Event Messages 24 IOV1007 Message Unable to assign a PCIe slot. Detailed Description The IOV slot management subsystem detected an error which may prevent the physical assignment/unassignment or turning off of a PCIe slot. The errors can be caused by PCIe training timeouts, false hot plug signals,or installation of an unsupported PCIe adapter card. For a list of supported PCIe adapter cards contact your service provider.
Category Configuration Subcategory IOV = IO Virtualization Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable IOV1009 Message Mismatch in Slot or Virtual Adapter FQDD and Server Slot FQDD count. Detailed Description The FQDD pairs identified in the messages do not match in the required method input parameters.
IPA Event Messages IPA0001 Message Invalid NIC IP address parameter specified. Detailed Description Invalid parameters passed to the function. Recommended Response Action Enter the valid IP Address. Category Audit Subcategory IPA = DRAC IP Address Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable IPA0002 Message Invalid IP address specified.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable IPA0003 Message Invalid subnet mask specified. Detailed Description Invalid parameters passed to the function. Recommended Response Action Enter the appropriate subnet mask. Category Audit Subcategory IPA = DRAC IP Address Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable IPA0100 Message Arguments The iDRAC IP Address changed from arg1 to arg2 . • arg1 = old IP Address • arg2 = new IP Address Detailed Description The iDRAC IP Address changed from the earlier IP Address identified in the message to the new IP Address identified in the message.
ISM Event Messages 26 ISM0000 Message The iDRAC Service Module is started on the operating system (OS) of server. Detailed Description The iDRAC Service Module is started on the OS of server. Recommended Response Action No response action is required. Category Audit Subcategory ISM = iDRAC Service Module Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Category Audit Subcategory ISM = iDRAC Service Module Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ISM0002 Message The OS to iDRAC Pass-through is disabled. The iDRAC Service Module is currently enabling the OS to iDRAC Pass-through in the USB NIC mode. Detailed Description The OS to iDRAC Pass-through mode is disabled.
ISM0003 Message The iDRAC Service Module is unable to discover iDRAC from the operating system of the server. Detailed Description The iDRAC Service Module could not successfully discover iDRAC from the server OS. However, the iDRAC Service Module will continue the discovery operation. Make sure that the IPMI drivers are enabled on the server operating system. Recommended Response Action No response action is required.
Server Administrator Trap ID Not Applicable ISM0005 Message The iDRAC Service Module has successfully restarted communication with iDRAC. Detailed Description The iDRAC Service Module has successfully restarted communication with iDRAC. Recommended Response Action No response action is required. Category Audit Subcategory ISM = iDRAC Service Module Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ISM0007 Message The iDRAC Service Module communication with iDRAC has ended. Detailed Description The iDRAC Service Module ended communication with iDRAC over the OS to iDRAC Pass-through channel. This is because either iDRAC is being restarted or the OS to iDRAC Pass-through configuration is being changed.
Recommended Response Action End the OpenManage Server Administrator session. The features will be automatically started by iDRAC Service Module. Category Audit Subcategory ISM = iDRAC Service Module Severity Severity 2 (Warning) LCD Message No LCD message display defined.
ISM0010 Message Arguments The iDRAC Service Module received a request from the arg1 to stop the services of Service Module. • arg1 = requesting source name Detailed Description The iDRAC Service Module received a request from a source identified in the message to stop the Service Module services. For example, a requesting source can be an OS or iDRAC.
Category Audit Subcategory ISM = iDRAC Service Module Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ISM0012 Message The IDRAC Service Module is successfully ended on the server operating system (OS). Detailed Description The IDRAC Service Module is successfully ended on the server OS. Recommended Response Action No response action is required.
Detailed Description The feature identified in the message is enabled by using the one of the iDRAC interfaces. Recommended Response Action No response action is required. Category Audit Subcategory ISM = iDRAC Service Module Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ISM0014 Message Arguments The feature arg1 is disabled.
ISM0015 Message The iDRAC Service Module detected a change in the host name of the server operating system (OS). Detailed Description The iDRAC Service Module detected a change in the host name of the server OS. Recommended Response Action No response action is required. Category Audit Subcategory ISM = iDRAC Service Module Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ISM0017 Message Arguments The BMC watchdog auto-recovery action is changed from arg1 to arg2 . • arg1 = original action • arg2 = new action Detailed Description The BMC watchdog auto-recovery action is changed from the original action identified in the message to the new action identified in the message. Recommended Response Action No response action is required.
Subcategory ISM = iDRAC Service Module Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable ISM0019 Message The OS Collector application did not start successfully on the server operating system (OS) because checksum verification did not succeed for some files.
Recommended Response Action Do the following: 1) Retry the operation. 2) If the issue persists, restart the iDRAC, and then retry the operation. Category Audit Subcategory ISM = iDRAC Service Module Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description The OS Collector application did not start successfully on the server operating system (OS) because the application encountered an error. Recommended Response Action Do the following: 1) Retry the operation. 2) If the issue persists, reinstall the OS Collector on the iDRAC to the most recent version available, and then retry the operation. Category Audit Subcategory ISM = iDRAC Service Module Severity Severity 2 (Warning) LCD Message No LCD message display defined.
JCP Event Messages 27 JCP000 Message New Detailed Description A new job with the job ID specified is created. Recommended Response Action No response action is required. Category Updates Subcategory JCP = Job Control Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable JCP001 Message Task successfully scheduled.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable JCP002 Message Unable to schedule the job. Detailed Description The Lifecycle Controller is not able to schedule a job at this time because of an internal error. Recommended Response Action Wait up to three minutes and retry the operation. If the problem persists, reboot the system and enumerate DCIM_Lifeycle Job to view the list of jobs that are currently scheduled.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable JCP004 Message Time elapsed - Job Failed. Detailed Description The jobs time window expired and the job failed to complete Recommended Response Action Retry the action and increase the time window so that the job can complete.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable JCP006 Message Invalid job attribute. Detailed Description One or more of the specified values for creating a job are invalid or an internal error has occurred when scheduling the job. Recommended Response Action Use the correct value for the job attribute and retry the operation.
Subcategory JCP = Job Control Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable JCP008 Message Job completed with errors. Detailed Description Multiple attributes were set in the operation but some set attribute actions were not successful.
Recommended Response Action If the job was not cancelled manually, then Lifecycle Controller may be in Recovery mode. To verify or change Recovery mode, use F2 Setup to select iDRAC Configuration then Lifecycle Controller Settings. Category Configuration Subcategory JCP = Job Control Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Detailed Description A new job cannot be created until the existing Export job is completed or the job is deleted. There can only be one Export Server Profile job running at a time. Recommended Response Action Do one of the following: 1) Retry the operation after the Export Server Profile job is completed. 2) Delete the scheduled Export job and retry the operation. Category Configuration Subcategory JCP = Job Control Severity Severity 2 (Warning) LCD Message No LCD message display defined.
JCP020 Message Cannot schedule jobs while export or import operations are running. Detailed Description Existing jobs cannot be scheduled while an Export Server Profile or Import Server Profile job is running. Recommended Response Action Retry the job scheduling operation after the export or import operation is completed. Category Configuration Subcategory JCP = Job Control Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable JCP024 Message Lifecycle Controller is in use. This job starts when Lifecycle Controller is available. Detailed Description Lifecycle Controller cannot gain access to internal storage due to use by another application or operation. This job starts when Lifecycle Controller is available. Recommended Response Action Wait for current Lifecycle Controller operation to complete.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable JCP026 Message Update packages are being downloaded. This job resumes when the downloads are completed. Detailed Description Update packages are being downloaded for other jobs initiated on this system. This job resumes when the downloads complete. Recommended Response Action No response action is required.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable JCP028 Message Job status updated. Detailed Description WSMan job status is updated. Recommended Response Action No response action is required Category Configuration Subcategory JCP = Job Control Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory JCP = Job Control Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log;None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable JCP030 Message Unable to schedule jobs while an iDRAC firmware update or configuration job is running. Detailed Description Unable to schedule jobs for execution while an iDRAC firmware update job is running.
Recommended Response Action Retry the operation. If the issue persists, reset the iDRAC by pressing the System ID button for 15 seconds, wait for the iDRAC to finish restarting, and then retry the operation. Category Configuration Subcategory JCP = Job Control Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LC Event Messages 28 LC001 Message Command successful. Detailed Description The command completed successfully. Recommended Response Action No response action is required. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC002 Message General failure.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC003 Message Failed to change the firmware update mode. Detailed Description An error occurred while trying to set the firmware update mode. Recommended Response Action Verify that the firmware version supports this mode. Also confirm that the command and parameters are correct.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC005 Message Invalid firmware update mode. Detailed Description The value provided for the update mode parameter is invalid. Recommended Response Action Verify that the correct firmware update mode was entered. The choices are: 1) Disable (default) 2)Allow version upgrade only 3) Match firmware of replaced part.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC007 Message Invalid Parameter. Detailed Description One of the parameters specified in the method is invalid. Recommended Response Action Verify that the parameters specified are correct. For a list of parameters for this method refer to the Lifecycle Controller User Guide.
Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC009 Message Insufficient method parameters. Detailed Description There were insufficient parameters specified for this command. Recommended Response Action Confirm that the parameters provided are correct.
Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC0100 Message Lifecycle Controller has entered Recovery mode. Detailed Description A persistent error has occurred while carrying out a Lifecycle Controller operation. This situation causes Lifecycle Controller to enter Recovery mode.
Recommended Response Action No response action is required. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC011 Message Certificate import operation failed. Detailed Description There was a general failure in the certificate import process.
Detailed Description Lifecycle Controller is in use by another process. Wait for other process to complete before attempting to run another command. Recommended Response Action Try one of the following: 1) Rerun the command after about 2 minutes. 2) Make sure that Lifecycle Controller Unified Server Configurator or an Update Package is not currently running on the server 3) Reset iDRAC and rerun the command.
LC014 Message Maximum comment length is 255 characters. Detailed Description Maximum comment length is 255 characters. Recommended Response Action Limit the number of characters in the comment to 255 characters. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable LC016 Message Arguments Missing required parameter, arg1 . • arg1 = parameter Detailed Description A required method argument was missing. Recommended Response Action Include all the parameters required for the command. Check Lifecycle Controller Profile documentation and try again. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC018 Message Server certificate successfully modified. iDRAC will now restart and be unavailable during restart. Detailed Description The certificate modification operation was successful. Communication to iDRAC will be lost as iDRAC restarts to use the new server certificate. Recommended Response Action No response action is required.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC020 Message PKCS12 decrypt of the certificate could not complete. Detailed Description The contents of the PKCS12 parameter was not valid because: 1) not a valid PKCS12 file 2) not a valid pfx file 3) did not contain a certificate that matched the private key in the file.
Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC022 Message Lifecycle Controller Log Export was successful. Detailed Description The Lifecycle Controller Log was successfully exported to the destination specified. Recommended Response Action No response action is required.
Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC024 Message Unable to retrieve Lifecycle Controller Log records. Detailed Description Unable to retrieve Lifecycle Controller Log records because of an issue internal to the firmware.
Recommended Response Action Make more space available on the network share and try the operation again. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC026 Message Lifecycle Controller Log Export method is not supported.
Detailed Description The Hardware Inventory XML file export operation was successful. Recommended Response Action No response action is required. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC028 Message Unable to retrieve Hardware Inventory information.
LC029 Message Invalid file path specified. Detailed Description An invalid File Path was specified in the export operation. Recommended Response Action Correct the specified file path and try again. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable LC031 Message Internal error occurred while exporting inventory. Detailed Description An internal error occurred while exporting the Hardware Inventory XML file. Recommended Response Action Reset iDRAC and retry the command. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC033 Message As-Shipped Hardware Inventory export was successful. Detailed Description The Hardware Inventory XML file representing the system configuration as shipped from the factory was successful. Recommended Response Action No response action is required. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC035 Message As-Shipped Hardware Inventory Export method is not supported. Detailed Description This method is not supported in this version of Firmware. Recommended Response Action Update the iDRAC firmware to a version that supports this method.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC037 Message An instance of Lifecycle Controller Log Export is already running. Detailed Description Lifecycle Controller is locked by another instance of Lifecycle Controller Log Export operation. Wait for that operation to complete before attempting to run another command.
Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC039 Message An instance of As-Shipped Inventory export is already in progress. Detailed Description Lifecycle Controller is locked by another instance of the As-Shipped Inventory export process. Allow the process to complete before attempting another export operation.
Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC041 Message Console name configure failed Detailed Description The length of the Console name exceeds the maximum length allowed or the file operation error encountered.
Recommended Response Action Configure the Virtual Address Management to Console mode, and then configure the name of a console. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC043 Message Work note contains non-printable or reserved characters.
Detailed Description The Lifecycle Controller system configuration wipe operation is currently running. The operation deletes user information from system hardware and resets BIOS, iDRAC and Lifecycle Controller to default settings. The current operation and system restart must complete before the operation can be attempted again. Recommended Response Action Wait for the Lifecycle Controller system configuration wipe operation that is currently running to complete before requesting another operation.
LC046 Message An instance of DownloadServerPublicKey is already running. Detailed Description The DownloadServerPublicKey operation is in progress. The operation may take a few minutes to complete before the operation can be attempted again. Recommended Response Action Wait a few minutes before retrying retry the operation. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable LC048 Message Invalid input value for IPChangeNotifyPS. Detailed Description The value provided to set the attribute identified in the message is invalid. Recommended Response Action For more information on the valid values, see Lifecycle Controller-Remote Services documentation. Retry the operation with a valid value for the IPChangeNotifyPS attribute.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC050 Message Invalid value for SystemServicesState. Detailed Description The value provided to set the attribute identified in the message is invalid. Recommended Response Action For more information on the valid values, see Lifecycle Controller-Remote Services documentation. Retry the operation with a valid value for the SystemServicesState attribute.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC052 Message Cannot create multiple Server Profile Import jobs. Detailed Description There can only be one Server Profile Import job at a time. Recommended Response Action Wait for the existing Server Profile Import job to run and complete or cancel it, before retrying the operation.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC054 Message Unable to write to the network share. Detailed Description The network share may be read-only or it may not have sufficient space for the export operation. Recommended Response Action Verify the network share is not read-only and has sufficient space for exporting, then retry the operation.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC056 Message AttributeName and AttributeValue count mismatch. Detailed Description The name value pairs in the input parameter arrays do not match in the input. Recommended Response Action Retry the operation with a valid (AttributeName, AttributeValue) pair.
Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC058 Message Arguments Invalid AttributeValue parameter value for corresponding AttributeName value, arg1 . • arg1 = AttributeName Detailed Description The attribute value specified in the AttributeValue array is not valid for the corresponding specified attribute.
Detailed Description The attribute specified is read only and the value cannot be changed. Recommended Response Action No response action is required. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LC061 Message Lifecycle controller is ready to take provisioning requests Detailed Description Jobs, invoke methods, enumerates can now be performed on Lifecycle controller. Lifecycle controller is ready to take provisioning requests. Recommended Response Action No response action is required. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable LC063 Message Cannot create new jobs until the existing running jobs are completed or deleted. Detailed Description All jobs must be completed before creating a new job. Recommended Response Action Retry after all the existing jobs are completed or deleted. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC065 Message Arguments The iDRAC static IP address information is not fully configured. The missing attribute InstanceID is arg1 . • arg1 = attribute key Detailed Description The static IPv4 information for the iDRAC represented by the related iDRACCard Attributes must be configured correctly.
Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC067 Message Successfully exported SSL Certificate. Detailed Description The Export Certification operation successfully exported the SSL Certificate. Recommended Response Action No response action is required.
Recommended Response Action Apply or cancel any pending attribute changes. Changes can be applied by creating a targeted configuration job, or the changes can be cancelled by invoking the DeletePendingConfiguration method. If a configuration job is in progress, wait until it is completed before retrying the import or export system configuration operation. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description The configuration XML file used for the import operation does not exist on the specified network share. Recommended Response Action Make sure the input configuration XML file for the operation exists on the network share. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LC072 Message An SSL Certificate is successfully generated. Detailed Description An SSL Certificate is successfully generated in response to the requested operation. Recommended Response Action Download the SSL Certificate and get it signed by an authority.. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable LC074 Message The Certificate export operation did not complete successfully. Detailed Description The Certificate export operation did not complete successfully. Recommended Response Action Retry the operation. If the issue persists, restart the iDRAC and retry the operation. Category Configuration Subcategory LC = Lifecycle Contr Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LC076 Message Unable to perform the Custom Signed Certificate (CSC) certificate delete operation. Detailed Description Unable to perform the Custom Signed Certificate (CSC) certificate delete operation. This may be due to IPMI communications issues. Recommended Response Action Retry the operation. If the issue persists, restart the iDRAC and retry the operation.
LCD Message No LCD message display defined.
LIC Event Messages 29 LIC000 Message The License Manager action succeeded. Detailed Description This command was successful. Recommended Response Action No response action is required. Category Audit Subcategory LIC = Licensing Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC001 Message The License Manager command parameter used is invalid.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC002 Message License Manager is unable to allocate the required resources at startup. Detailed Description The error may occur when License Manager: 1) Is unable to allocate system resources. 2) Determines one or more files is incompatible with the current firmware version.
Recommended Response Action Re-issue the command. If the issue persists, contact technical support. Refer to your product documentation to choose the contact method that is convenient for you. Category Audit Subcategory LIC = Licensing Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC004 Message An internal system error has occurred.
LIC005 Message Import failed: The maximum number of licenses are installed. Detailed Description The maximum number of installed licenses has been reached. Recommended Response Action Delete one of the currently installed licenses and retry the import. Category Audit Subcategory LIC = Licensing Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable LIC007 Message Invalid entry: Object does not exist or cannot be found. Detailed Description Each License Manager object has a unique identifier by which it may be accessed. If the user supplied identifier is outside the acceptable range or the object no longer exists in the system, then this error is returned.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC009 Message The license upgrade was unsuccessful. Detailed Description An upgrade license carries specific information about the license it is replacing. If that information does not match, then the license import is aborted. Recommended Response Action Obtain a new license file with the correct upgrade information.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC011 Message A non-evaluation license cannot be replaced with an evaluation license. Detailed Description License Manager does not allow the replacement of a non-evaluation license with an evaluation license.
Recommended Response Action Re-import the license. Category Audit Subcategory LIC = Licensing Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC013 Message These license features are not supported by this firmware version. Detailed Description The license includes features not supported in this firmware release.
Detailed Description An attempt to lock the License Manager database for Lifecycle Controller backup or restore occurred when the License Manager database was already locked. This may occur when two or more users attempt to do a backup or restore operation simultaneously. Recommended Response Action Repeat the Lifecycle Controller backup or restore operation. Category Audit Subcategory LIC = Licensing Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LIC016 Message The feature dependencies of the license are not met. Detailed Description The license includes features that are dependent upon additional licensed features not included in this license. These licensed features are not activated until license(s) with the dependent licensed features are imported to the system. Recommended Response Action Import the license(s) that meet the license features dependencies.
Server Administrator Trap ID Not Applicable LIC018 Message The license is already imported. Detailed Description The license is already imported on the system and does not need to be reimported. Recommended Response Action No response action is required. Category Audit Subcategory LIC = Licensing Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC020 Message Import failed: End User License Agreement (EULA) import upgrade warning. Detailed Description Importing an upgrade license without a base license is not allowed, as it may be a violation of the license EULA agreement. If the base license was deleted, the system allows the user to override the warning by invoking the import override option.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC022 Message License Manager database locked due to ongoing backup and restore operation. Detailed Description License Manager database is locked while a backup and restore operation is in progress. License import/export/delete operations are not allowed but a user can view license information.
Recommended Response Action Purchase a new license to prevent interruption of licensed features. Category Audit Subcategory LIC = Licensing Severity Severity 2 (Warning) Trap/EventID 8514 LCD Message No LCD message display defined. Initial Default SNMP Alert;EMAIL Alert;OS Log;LC Log;Remote System Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC202 Message A system error was detected during License Manager startup.
LIC203 Message Arguments The license arg1 has encountered an error. • arg1 = entitlement ID Detailed Description Signature verification failed due to an error in the saved license file. Recommended Response Action Delete and re-import the license file. Category Audit Subcategory LIC = Licensing Severity Severity 1 (Critical) Trap/EventID 8513 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC205 Message License Manager database lock timeout has been exceeded. Detailed Description The License Manager sets a maximum time period that its database may be locked. If that timeout exceeds, it releases the lock conditions and reports the error. The user must assume that the Lifecycle Controller backup or restore operation failed and should repeat the operation.
Subcategory LIC = Licensing Severity Severity 2 (Warning) Trap/EventID 8514 LCD Message No LCD message display defined. Initial Default SNMP Alert;EMAIL Alert;OS Log;LC Log;Remote System Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC207 Message Arguments License arg1 on device arg2 has expired. • arg1 = entitlement ID • arg2 = device name Detailed Description The license has expired.
Arguments • arg1 = entitlement ID • arg2 = device name Detailed Description A license was successfully imported. Recommended Response Action No response action is required. Category Audit Subcategory LIC = Licensing Severity Severity 3 (Informational) Trap/EventID 8515 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC210 Message Arguments License arg1 deleted from device arg2 successfully. • arg1 = entitlement ID • arg2 = device name Detailed Description A license was successfully deleted. Recommended Response Action No response action is required. Category Audit Subcategory LIC = Licensing Severity Severity 3 (Informational) Trap/EventID 8515 LCD Message No LCD message display defined.
Subcategory LIC = Licensing Severity Severity 3 (Informational) Trap/EventID 8515 LCD Message No LCD message display defined. Initial Default SNMP Alert;OS Log;LC Log;Remote System Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC501 Message A required license is missing or expired.
Recommended Response Action Contact technical support. Refer to your product documentation to choose the contact method that is convenient for you. Category Audit Subcategory LIC = Licensing Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LIC503 Message Arguments Unable to complete the current operation.
LNK Event Messages 30 LNK0001 Message Network share name unavailable. Detailed Description The entered network share name is not valid. Recommended Response Action Enter a valid network share name and retry the operation. For more information, see Lifecycle Controller Users Guide. Category System Health Subcategory LNK = Link Status Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LNK0003 Message Unable to connect to the DNS server. Detailed Description Cannot connect to the DNS server because of network issues or there is no response from the DNS server. Recommended Response Action Verify that the server is connected to the network and retry the operation.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LNK0005 Message Unable to connect to DHCP server. Detailed Description Error occurred while communicating with the DHCP server because the network settings are not configured correctly or the DHCP server could not be contacted.
Subcategory LNK = Link Status Severity Severity 1 (Critical) Trap/EventID 2249 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LNK2701 Message Arguments The arg1 network link is up. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
LOG Event Messages 31 LOG001 Message Missing required InstanceID or JobID parameter. Detailed Description One or more required parameters needed for the method invoked in the operation are missing. Recommended Response Action To provide the correct value for the specified parameter, see Lifecycle ControllerRemote Services documentation. Category Configuration Subcategory LOG = Log event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LOG003 Message ConfigResults not available for log entry specified. Detailed Description The log entry with the specified InstanceID does not have any associated configuration results. Recommended Response Action Verify the ConfigResults availability for the InstanceID through enumeration of the LogEntry class and retry the operation.
Recommended Response Action No response action is required. Category Audit Subcategory LOG = Log event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LOG007 Message Arguments The previous log entry was repeated arg1 times. • arg1 = log entry count Detailed Description This message is generated after a series of sequential duplicate events.
LOG008 Message The complete Lifecycle Log export was successful. Detailed Description The complete Lifecycle Log export was successful. Recommended Response Action No response action is required. Category Audit Subcategory LOG = Log event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable LOG202 Message Recovered from Lifecycle Controller Log comments file corruption. Detailed Description Unable to access part of Lifecycle Controller Log comments file during iDRAC boot. The file was truncated at the point of corruption. Recommended Response Action No response action is required. Category Configuration Subcategory LOG = Log event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LOG204 Message Lifecycle Log archive operation did not complete. Detailed Description The archive operation did not complete. 10% of the events from the cache will be dropped to make space for new events. Recommended Response Action No response action is required. Category Configuration Subcategory LOG = Log event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default OS Log;None Server Administrator Event ID 5550 Server Administrator Trap ID Not Applicable LOG321 Message Arguments The log status is unknown. Log type: arg1 . • arg1 = log type Detailed Description The hardware log may not be up-to-date. The log type information is provided. Recommended Response Action Make sure that iDRAC is functioning correctly.
Recommended Response Action No response action is required. Category System Health Subcategory LOG = Log event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default SNMP Alert;OS Log;None Server Administrator Event ID 5552 Server Administrator Trap ID 5552 LOG323 Message Arguments The log size is near maximum capacity. Log type: arg1 . • arg1 = log type Detailed Description The size of a hardware log in the system is near its maximum capacity.
LOG324 Message Arguments The log size has reached its maximum capacity. Log type: arg1 . • arg1 = log type Detailed Description The size of a hardware log in the system has reached its maximum capacity. The log type information is provided. Recommended Response Action Clear the log to make sure new entries are recorded. Category System Health Subcategory LOG = Log event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID 5555 Server Administrator Trap ID Not Applicable LOG326 Message The Alert Log was cleared. Detailed Description The Alert Log was cleared. Recommended Response Action No response action is required. Category Audit Subcategory LOG = Log event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable LOG328 Message The Server Based Management Mode is enabled. Detailed Description The Server Based Management Mode is enabled. Chassis based PSUs, fans, and sensor information can be displayed from server based system management tools. Recommended Response Action No response action is required.
LCD Message No LCD message display defined.
MEM Event Messages 32 MEM0000 Message Arguments Persistent correctable memory errors detected on a memory device at location(s) arg1 . • arg1 = location Detailed Description The memory is operational. This is an early indicator of a possible future uncorrectable error. Recommended Response Action Re-install the memory component. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Recommended Response Action Re-install the memory component. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID 2265 LCD Message Multi-bit memory error on .
MEM0003 Message Arguments Stuck bit memory error detected on a memory device at location arg1 . • arg1 = location Detailed Description The memory is operational. This is an early indicator of a possible future uncorrectable error. Recommended Response Action Re-install the memory component. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM0005 Message Arguments Persistent correctable memory error limit reached for a memory device at location(s) arg1 . • arg1 = location Detailed Description The memory is operational. This is an early indicator of a possible future uncorrectable error. Recommended Response Action Re-install the memory component.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM0007 Message Arguments Unsupported memory configuration; check memory device at location arg1 .
Server Administrator Trap ID Not Applicable MEM0008 Message Arguments Memory device at location arg1 is spare memory. • arg1 = location Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined.
Severity Severity 2 (Warning) Trap/EventID 2266 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM0010 Message Arguments Memory device at location arg1 is overheating. • arg1 = location Detailed Description System performance is degraded. Recommended Response Action If unexpected, review system logs for power or thermal exceptions.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM0020 Message Arguments Memory device at location arg1 is enabled.
MEM0021 Message Arguments Persistent correctable memory error limit reset for a memory device at location arg1 . • arg1 = location Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM0024 Message Arguments Memory device at location arg1 is no longer spare memory. • arg1 = location Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM0601 Message Arguments Memory device is removed from location arg1 . • arg1 = location Detailed Description None Recommended Response Action No response action is required.
MEM0700 Message Arguments The persistent correctable memory error rate is at normal levels for a memory device at location arg1 . • arg1 = location Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM0702 Message Arguments Correctable memory error rate exceeded for arg1 . • arg1 = location Detailed Description The memory may not be operational. This an early indicator of a possible future uncorrectable error. Recommended Response Action Re-install the memory component. If the problem continues, contact support.
Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1001 Message Arguments Memory device at location arg1 failed to transition to a running state.
MEM1002 Message Arguments Memory device at location arg1 is in test. • arg1 = location Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1004 Message Arguments Memory device at location arg1 is powered off. • arg1 = location Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined.
Recommended Response Action Re-attempt memory removal process Category System Health Subcategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID 2265 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1006 Message Arguments Memory device at location arg1 is online. • arg1 = location Detailed Description None Recommended Response Action No response action is required.
MEM1007 Message Arguments Memory device at location arg1 failed to transition to online. • arg1 = location Detailed Description None Recommended Response Action Re-attempt memory removal process Category System Health Subcategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID 2265 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1009 Message Arguments Memory device at location arg1 failed to transition to offline.
Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1011 Message Arguments Memory device at location arg1 is on-duty.
MEM1012 Message Arguments Memory device at location arg1 is in a degraded state. • arg1 = location Detailed Description None Recommended Response Action Re-install the memory component. If the problem continues, contact support. Category System Health Subcategory MEM = Memory Severity Severity 2 (Warning) Trap/EventID 2266 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1014 Message Arguments Memory device at location arg1 is in a power save state. • arg1 = location Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined.
Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1016 Message Arguments Memory device at location arg1 is not installed correctly.
MEM1017 Message Arguments Memory device at location arg1 is installed correctly. • arg1 = location Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1200 Message Memory RAID is redundant.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1201 Message Arguments Memory RAID redundancy is lost. Check memory device at location(s) arg1 . • arg1 = location Detailed Description None Recommended Response Action Re-install the memory component. If the problem continues, contact support. Category System Health Subcategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID 2265 LCD Message Memory RAID lost on .
Category System Health Subcategory MEM = Memory Severity Severity 2 (Warning) Trap/EventID 2266 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1203 Message Memory is not redundant. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1205 Message Arguments Memory mirror redundancy is lost. Check memory device at location(s) arg1 .
MEM1206 Message Arguments Memory mirror redundancy is degraded. Check memory device at location arg1 . • arg1 = location Detailed Description The memory may not be seated correctly, misconfigured, or has failed. Recommended Response Action Review system logs for memory exceptions. Re-install memory at location Category System Health Subcategory MEM = Memory Severity Severity 2 (Warning) Trap/EventID 2266 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1208 Message Arguments Memory spare redundancy is lost. Check memory device at location arg1 . • arg1 = location Detailed Description The assigned spare is no longer available. Recommended Response Action Review system logs for memory exceptions.
Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) Trap/EventID 2267 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1210 Message Memory is redundant. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action Review system logs for memory exceptions. Re-install memory at location Category System Health Subcategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID 2265 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM1214 Message Memory redundancy is degraded.
MEM6000 Message Memory device monitoring is disabled. Detailed Description The memory module may not be correctly seated, wrongly configured, or has failed. Recommended Response Action Review the Embedded System Management (ESM) Log for memory exceptions. Reinstall the memory modules. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID 5401 Server Administrator Trap ID Not Applicable MEM6002 Message Arguments Memory device status is normal. Memory device location: arg1 . • arg1 = location Detailed Description The memory device identified in the message has returned to a normal state. Recommended Response Action No response action is required. Category System Health Subcategory MEM = Memory Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Recommended Response Action Review the Embedded System Management (ESM) Log for memory exceptions. Reinstall the memory modules at the identified location . Category System Health Subcategory MEM = Memory Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default SNMP Alert;OS Log;None Server Administrator Event ID 5403 Server Administrator Trap ID 5403 MEM6004 Message Arguments Memory device status is critical.
MEM6005 Message Arguments Memory device has failed. Memory device location: arg1 , Possible memory module event cause: arg2 . • arg1 = location • arg2 = cause Detailed Description The memory module failed because of an irrecoverable error. Recommended Response Action Review the Embedded System Management (ESM) Log for memory exceptions. Remove the old memory module and install a new memory module at the identified location .
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM7002 Message A hardware mismatch detected for memory riser. Detailed Description None Recommended Response Action Review product documentation for proper memory riser installation and configuration Category System Health Subcategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID 2265 LCD Message Memory riser mismatch detected.
Severity Severity 1 (Critical) Trap/EventID 2265 LCD Message SBE log disabled on . Reseat memory Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM8001 Message Arguments Persistent correctable memory error logging enabled for a memory device at location arg1 . • arg1 = location Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action Do one of the following: 1) Reseat the memory riser and restart the server. 2) If the issue is not resolved by preceding action, reseat the processor and restart the server. 3) If the issue persists, contact your service provider. Category System Health Subcategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID 2265 LCD Message Memory interconnect degraded. Reseat memory riser.
Arguments • arg1 = QPI link number Detailed Description A correctable error was detected in propagation of signals between processors through the Intel QPI interconnect interconnect identified in the message. Recommended Response Action Do one of the following: 1) Restart the server and check whether the issue persists. 2) If the issue is not resolved by the preceding action, reseat the processors and restart the server. 3) If the issue persists, contact your service provider.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable MEM9004 Message Arguments Intel QPI interconnect arg1 has degraded. • arg1 = QPI link number Detailed Description A link degradation was detected in propagation of signals between processors through the Intel QPI interconnect interconnect identified in the message. The system will continue to operate at reduced performance.
Recommended Response Action Do one of the following: 1) Reseat the memory riser and restart the server. 2) If the issue is not resolved by preceding action, reseat the processor and restart the server. 3) If the issue persists, contact your service provider. Category System Health Subcategory MEM = Memory Severity Severity 1 (Critical) Trap/EventID 2265 LCD Message Intel SMI 2 interconnect degraded. Reseat memory riser.
MEM9007 Message Arguments Intel SMI 2 Memory interconnect arg1 has a non-recoverable issue. • arg1 = link number Detailed Description A non-recoverable link issue was detected in propagation of signals between processor and memory through the Intel SMI 2 memory interconnect identified in the message. Recommended Response Action Do one of the following: 1) Reseat the memory riser and restart the server. 2) If the issue is not resolved by preceding action, reseat the processor and restart the server.
LCD Message Intel DDR interconnect has fatal error. Reseat mem riser.
NIC Event Messages 33 NIC001 Message The command was successful. Detailed Description The command was successful. Recommended Response Action No response action is required. Category Configuration Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC003 Message Missing required parameter Detailed Description An invalid number of arguments was passed to the method. Recommended Response Action Enter all the required command parameters. Check documentation and try again. Category Configuration Subcategory NIC = NIC Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC005 Message Mismatch in AttributeName and AttributeValue count Detailed Description The number of AttributeName and AttributeValue parameters do not match. Recommended Response Action Pass the same number of parameters for AttributeName and AttributeValue.
Subcategory NIC = NIC Config Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC007 Message A configuration job already exists, Cannot create another configuration job on specified target until existing job is completed or is cancelled Detailed Description A configuration job already exists for the specified target.
Recommended Response Action Change the configuration of one or more attributes and then create a configuration job. Category Configuration Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC009 Message Lifecycle Controller is currently in use.
Detailed Description For 11G systems: System Services must be enabled to perform the requested operation. System Services has been disabled through the iDRAC configuration utility accessed by pressing CTRL+E on boot up or through a remote operation. For 12G systems: Lifecycle Controller must be enabled to perform the requested operation.
Server Administrator Trap ID Not Applicable NIC012 Message No pending data to delete. Detailed Description No changes to BIOS attribute data are available between the previous configuration and the current configuration. Recommended Response Action No response action is required. Category Configuration Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC014 Message Arguments Invalid AttributeValue for AttributeName arg1 • arg1 = attribute name Detailed Description AttributeValue may be invalid because of the following causes: 1) Length of new AttributeValue is not within minLength and maxLength 2) Value of new AttributeValue is not within LowerBound and UpperBound 3) Value of new Attributevalue is not one of the possible values.
Recommended Response Action No response action is required. Category Configuration Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC016 Message Arguments AttributeValue cannot be changed for disabled AttributeName arg1 .
NIC017 Message Unable to delete vFlash pending one-time boot configuration Detailed Description Unable to delete vFlash pending one-time boot configuration. Recommended Response Action Remove AC power from system and after restoring AC power, retry the operation. Category Configuration Subcategory NIC = NIC Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable NIC021 Message Cannot authenticate specified BIOS password. Detailed Description The old BIOS password used to change the password is incorrect. Recommended Response Action Enter the correct old password for the BIOS and retry the operation. Category Configuration Subcategory NIC = NIC Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC023 Message Cannot perform the operation due to an unknown error in iDRAC. Detailed Description The operation did not complete successfully because of an unknown error in iDRAC. Recommended Response Action Retry the action. If the issue persists, reset the iDRAC. Category Configuration Subcategory NIC = NIC Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC100 Message Arguments The NIC arg1 Port arg2 network link is down. • arg1 = Controller • arg2 = Port Detailed Description The network link is down. Either the network cable is not connected or the network device is not working. Recommended Response Action Verify that the network port is enabled and if the port has Activity/Speed LEDs, that they are lit.
Detailed Description The transition from network link not started (down) to network link started (up) has been detected on the NIC controller port identified in the message. Recommended Response Action No response action is required. Category System Health Subcategory NIC = NIC Config Severity Severity 3 (Informational) Trap/EventID 2091 LCD Message No LCD message display defined.
NIC501 Message The requested object is not allowed to be configured if Auto Config \nis enabled. Detailed Description Autoconfig assigns values to the network components. Recommended Response Action Disable Autoconfig and then modify the value. Category System Health Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable NIC503 Message The DNS server IP address is not allowed to be configured \nif DNS server DHCP (cfgDNSServersFromDHCP) is enabled. Detailed Description The value of the specified parameter cannot be changed. Recommended Response Action Disable the cfgDNSServersFromDHCP object. Category System Health Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC505 Message The DNS domain name is not allowed to be configured if \ndomain name DHCP (cfgDNSDomainNameFromDHCP) is enabled. Detailed Description The value of the specified parameter cannot be changed. Recommended Response Action Disable the cfgDNSDomainNameFromDHCP object.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC507 Message Unable to determine current NIC state. Detailed Description For the requested operation, enable the NIC to get the NIC details. Recommended Response Action Check if the NIC is disabled. If disabled, enable the NIC. Category System Health Subcategory NIC = NIC Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC509 Message NIC is now ENABLED Detailed Description Success message. Recommended Response Action No response action is required. Category System Health Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC511 Message NIC is already ENABLED Detailed Description Success message. Recommended Response Action No response action is required. Category System Health Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC513 Message DHCP6 is already ENABLED Detailed Description Success message. Recommended Response Action No response action is required.
Category System Health Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable NIC515 Message DHCP6 is now ENABLED Detailed Description Success message. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory NIC = NIC Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
OSD Event Messages 34 OSD062 Message The process of installing an operating system or hypervisor is started and is in progress. Detailed Description The process of installing an operating system or hypervisor is started and is in progress. Recommended Response Action No response action is required. Category Configuration Subcategory OSD = OS Deployment Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD064 Message The process of installing an operating system or hypervisor is abruptly stopped either by the user or the installation infrastructure. Detailed Description The process of installing an operating system or hypervisor is abruptly stopped either by the user or the installation infrastructure.
Subcategory OSD = OS Deployment Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD1 Message The command was successful. Detailed Description The command was successful. Recommended Response Action No response action is required.
Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD11 Message Driver Pack does not have drivers for the selected operating system. Detailed Description Lifecycle Controller does not have any drivers for the selected operating system.
Recommended Response Action 1) Rerun the command. 2) Reset iDRAC and rerun the command. Category Configuration Subcategory OSD = OS Deployment Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD13 Message Cannot mount the USB device needed to copy drivers for the selected operating system.
Detailed Description iDRAC was unable to expose the drivers as a USB device for the OS installation to proceed. Recommended Response Action 1) Rerun the command. 2) Reset iDRAC and rerun the command. Category Configuration Subcategory OSD = OS Deployment Severity Severity 1 (Critical) LCD Message No LCD message display defined.
OSD16 Message Mount network share failed - incorrect IP address or share name. Detailed Description Unable to mount the network share using the parameters specified in the command because either the IP address or share name is incorrect. Recommended Response Action Rerun the command with the correct IP address and share name. Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable OSD18 Message Unable to locate the ISO image on the network share point. Detailed Description Unable to find the ISO file specified in the network share. Make sure that the correct ISO file path was entered into the command and that all other user credentials are correct. Recommended Response Action Rerun the command with the correct ISO file path.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD2 Message General failure. Detailed Description An unknown error occurred. Recommended Response Action 1) Rerun the command. 2) Reset iDRAC and run the command. Category Configuration Subcategory OSD = OS Deployment Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD21 Message Unable to boot to ISO image. Detailed Description Booting to ISO has failed. Either BIOS was unable to boot to the ISO image or the provider did not get a response in 5 minutes from BIOS on successful boot to ISO image. Recommended Response Action 1) Make sure that a POST error did not result in user interaction (Press F1 to continue or F2 to run BIOS setup).
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD23 Message Unable to continue with DetachISOImage - another command is in the process of exposing the ISO Image and booting to it. Detailed Description Cannot continue with DetachISOImage because another command is in the process of exposing the ISO image and booting to it.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD25 Message Unable to detach USB device containing operating system drivers. Detailed Description Detaching the USB device (that contains drivers for the operating system installation) from the host has failed. The device may be detached, or iDRAC may not be operating normally.
Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD27 Message Copying drivers for selected operating system failed. Detailed Description Copying drivers for selected operating system failed. The Driver Pack may be unusable. Recommended Response Action Update the Driver Pack using USC or DUP and then rerun the command.
Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD29 Message Driver Pack configuration file not found in Lifecycle Controller. The Driver Pack might be corrupt. Detailed Description Driver Pack configuration file not found in Lifecycle Controller. Driver Pack may be unusable.
Recommended Response Action 1) After two minutes, rerun the command. 2) Make sure that USC or DUP is not currently running on the server. 3) Reset iDRAC and rerun the command. Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description Copying drivers for the selected operating system to network share failed. The share may be read-only or the Driver Pack present in Lifecycle Controller may be unusable. Recommended Response Action 1) Make sure that the network share has write permission. 2) Update the Driver Pack using USC or DUP and then rerun the command. Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined.
OSD33 Message Installed BIOS version does not support this method. Detailed Description The system has an older version of BIOS that does not support this method. Install the latest version of BIOS to use this method. Recommended Response Action Update the BIOS to version 1.2 or later and then rerun the command. Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable OSD35 Message Lifecycle Controller is not enabled. Detailed Description Lifecycle Controller is disabled on the system, so none of the remote operating system deployment commands will work. Make sure Lifecycle Controller is enabled before running any command. Recommended Response Action Reboot the system and enable System Services by pressing CTRL+E option when prompted to do so in the POST.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD37 Message ISO image size too large. Detailed Description ISO Image size is bigger than the available size in VFlash. Recommended Response Action 1) Use a smaller size ISO Image. 2) Format the VFlash using the iDRAC GUI, RACADM, or iDRAC configuration utility and then retry this command.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD39 Message Unable to find the VFlash. Detailed Description Unable to get VFlash information from internal instrumentation. Recommended Response Action 1) Make sure the Dell VFlash is seated correctly. 2) Make sure a Dell licensed VFlash card is inserted 3) Make sure the Dell VFlash doesnt have any hardware issues by accessing it through the iDRAC GUI.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD40 Message VFlash is not Dell licensed. Detailed Description This is not a Dell-licensed VFlash. Recommended Response Action Insert a Dell VFlash and then retry this command. Category Configuration Subcategory OSD = OS Deployment Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD42 Message Downloading ISO File to VFlash failed. Detailed Description There was an error while copying the ISO image from the network share to the VFlash. Recommended Response Action 1) Make sure the network connection is working.
Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD44 Message Unable to detach ISO image on VFlash. Detailed Description The ISO on VFlash is not currently attached, so the DetachISOFromVFlash command could not be executed.
Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD46 Message VFlash in use. Detailed Description Another process (iDRAC GUI /racadm/iDRAC configuration utility) is currently accessing VFlash. Recommended Response Action Wait until the access to VFlash is relinquished and then retry this command.
Recommended Response Action Make sure that the firewall is disabled, and that the credentials (username, password) are correct. Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD48 Message ISO Images of more than 4GB not supported.
Detailed Description VFlash cannot be accessed because RIPS mode is enabled. Recommended Response Action Disable the RIPS mode from BIOS or from the iDRAC GUI, and then continue executing the method. Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined.
OSD50 Message Lifecycle Controller is in field service mode. Detailed Description Lifecycle Controller is in field service mode and needs to be updated before proceeding further. Recommended Response Action Install the Lifecycle Controller field services package using the iDRAC GUI. Category Configuration Subcategory OSD = OS Deployment Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable OSD52 Message vFlash is disabled. Detailed Description vFlash is disabled. Recommended Response Action Enable the vFlash from the iDRAC GUI or RACADM, and then proceed. Category Configuration Subcategory OSD = OS Deployment Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD54 Message vFlash already has 16 partitions Detailed Description vFlash allows only 16 partitions to be created Recommended Response Action Make sure that there are less than 16 partitions before creating another partition on vFlash. Category Configuration Subcategory OSD = OS Deployment Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD56 Message An ISO is already connected using Remote File Share (RFS). Detailed Description An ISO is already connected using Remote File Share (RFS). The connection might have been initiated from iDRAC GUI, racadm, or Remote Services API.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD58 Message Unable to connect an ISO using Remote File Share (RFS). Detailed Description The connect ISO operation using Remote File Share (RFS) did not complete successfully. Recommended Response Action Verify all the parameters are correct. If the problem persists. then reset iDRAC and retry the operation.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD6 Message Cannot allocate memory. Detailed Description Unable to dynamically allocate memory to perform the task. Recommended Response Action Reset iDRAC and run the command.
Subcategory OSD = OS Deployment Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD61 Message IP Address format is invalid. Detailed Description The IP Address format is invalid and cannot be validated. The specified IP address may not be a valid IPv4 or IPv6 address. Recommended Response Action Verify the IP address format and retry the operation.
Category Configuration Subcategory OSD = OS Deployment Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSD8 Message Setting Boot to PXE through IPMI failed. Detailed Description The BIOS boot order set to PXE using a standard IPMI command has failed. Recommended Response Action 1) Check BIOS PXE settings. 2) Rerun the command.
Recommended Response Action 1) Rerun the command. 2) Reset iDRAC and rerun the command. Category Configuration Subcategory OSD = OS Deployment Severity Severity 1 (Critical) LCD Message No LCD message display defined.
OSE Event Messages 35 OSE0000 Message A critical stop occurred during OS load. Detailed Description The system halted due to an exception during operating system load or operating system initialization. Recommended Response Action Review operating system logs and system video for additional information Category System Health Subcategory OSE = OS Event Severity Severity 1 (Critical) Trap/EventID 2409 LCD Message No LCD message display defined.
Trap/EventID 2409 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSE0002 Message An OS graceful stop occurred. Detailed Description (IPMI sensor type 20h - offset 02h). Recommended Response Action No response action is required. Category System Health Subcategory OSE = OS Event Severity Severity 3 (Informational) Trap/EventID 2411 LCD Message No LCD message display defined.
Category System Health Subcategory OSE = OS Event Severity Severity 3 (Informational) Trap/EventID 2411 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSE0004 Message A soft shut-down initiated by platform event filter. Detailed Description A separate exception or status condition shutdown the operating system. (IPMI sensor type 20h - offset 04h).
Recommended Response Action review operating system logs and system video for additional information Category System Health Subcategory OSE = OS Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSE1000 Message A: boot completed.
Detailed Description None Recommended Response Action review system boot configuration and boot media. Verify the media in a: is bootable. See system video for additional information. Category System Health Subcategory OSE = OS Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSE1002 Message C: boot completed.
OSE1003 Message Failed to boot from C. Detailed Description None Recommended Response Action Review system boot configuration and boot media. Verify the media in C: is bootable. See system video for additional information. Category System Health Subcategory OSE = OS Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable OSE1005 Message PXE boot failed. Detailed Description None Recommended Response Action Review system boot configuration, local PXE configuration, and PXE server configuration Category System Health Subcategory OSE = OS Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSE1007 Message Diagnostic boot failed. Detailed Description None Recommended Response Action Review system boot configuration and boot media. See system video for additional information Category System Health Subcategory OSE = OS Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSE1009 Message Failed to boot from CD-ROM. Detailed Description None Recommended Response Action Review system boot configuration and boot media. Verify the media in the CDROM is bootable. See system video for additional information Category System Health Subcategory OSE = OS Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSE1011 Message Failed to boot from ROM. Detailed Description None Recommended Response Action Check system event logs for additional exception information. Power down the system and attempt to boot again. Category System Health Subcategory OSE = OS Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable OSE1013 Message Failed to boot. Detailed Description None Recommended Response Action Review system boot configuration and boot media.
PCI Event Messages 36 PCI1300 Message A front panel diagnostic interrupt was detected. Detailed Description The front panel diagnostic was pressed, and the system may be halted as a result. The interrupt was user induced. Recommended Response Action Reset the system to continue operation. Category System Health Subcategory PCI = PCI Device Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Category System Health Subcategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID 2417 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI1304 Message An I/O channel check error was detected. Detailed Description None Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device.
• arg2 = device • arg3 = func Detailed Description None Recommended Response Action Reboot the system and update the component drivers. Category System Health Subcategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID 2417 LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI1310 Message Arguments A PCI system error was detected on a component at bus arg1 device arg2 function arg3 . • arg1 = bus • arg2 = device • arg3 = func Detailed Description System performance may be degraded, or system may fail to operate. Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device.
Recommended Response Action No response action is required. Category System Health Subcategory PCI = PCI Device Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI1314 Message Arguments A bus correctable error was detected on a component at bus arg1 device arg2 function arg3 .
Server Administrator Trap ID Not Applicable PCI1316 Message Arguments A bus uncorrectable error was detected on a component at bus arg1 device arg2 function arg3 . • arg1 = bus • arg2 = device • arg3 = func Detailed Description System performance may be degraded, or system may fail to operate. Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device.
Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device. Category System Health Subcategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID 2417 LCD Message Fatal error on bus device function . Power cycle system.
Server Administrator Trap ID Not Applicable PCI1320 Message Arguments A bus fatal error was detected on a component at bus arg1 device arg2 function arg3 . • arg1 = bus • arg2 = device • arg3 = func Detailed Description System performance may be degraded, or system may fail to operate. Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device.
Recommended Response Action Remove and reinsert the component identified in the message, and then monitor the log for a re-occurrance of the issue. If the issue persists, and occurs during server startup, update the component firmware. If the issue persists and occurs during OS runtime, restart the server and update the OS drivers for the component identified in the message.
Server Administrator Trap ID Not Applicable PCI1342 Message Arguments A bus time-out was detected on a component at slot arg1 . • arg1 = number Detailed Description System performance may be degraded. The device has failed to respond to a transaction (master/target abort or completion timeout). Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device.
LCD Message An I/O channel check error detected. Power cycle system. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI1346 Message Arguments A software error was detected on a component at slot arg1 . • arg1 = number Detailed Description None Recommended Response Action Reboot the system and update the component drivers.
Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device. Category System Health Subcategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID 2417 LCD Message PCI parity error on slot . Reseat PCI card Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI1350 Message Arguments A PCI system error was detected on a component at slot arg1 .
PCI1354 Message Arguments A bus correctable error was detected on a component at slot arg1 . • arg1 = number Detailed Description System performance may be degraded. Recommended Response Action Cycle input power, update component drivers, remove and re-install the device at the next scheduled service time. Category System Health Subcategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID 2417 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI1358 Message Arguments A fatal error was detected on a component at slot arg1 . • arg1 = number Detailed Description System performance may be degraded, or system may fail to operate. Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device.
Recommended Response Action Cycle input power, update component drivers, if device is removable, re-install the device. Category System Health Subcategory PCI = PCI Device Severity Severity 1 (Critical) Trap/EventID 2417 LCD Message Bus fatal error on slot . Reseat PCI card Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI1362 Message Arguments Bus performance degraded for a component at slot arg1 .
PCI2000 Message Arguments A fatal IO error detected on a component at bus arg1 device arg2 function arg3 . • arg1 = bus • arg2 = device • arg3 = func Detailed Description System performance may be degraded, or system may fail to operate. Recommended Response Action Cycle input power, update component drivers, remove and re-install the device.
Subcategory PCI = PCI Device Severity Severity 3 (Informational) Trap/EventID 2419 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI2002 Message Arguments A fatal IO error detected on a component at slot arg1 . • arg1 = number Detailed Description System performance may be degraded, or system may fail to operate.
Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PCI = PCI Device Severity Severity 3 (Informational) Trap/EventID 2419 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI3000 Message Device option ROM on embedded NIC failed to support Link Tuning or FlexAddress.
Server Administrator Trap ID Not Applicable PCI3001 Message Device option ROM on embedded NIC was successfully updated. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PCI = PCI Device Severity Severity 3 (Informational) Trap/EventID 2419 LCD Message No LCD message display defined.
Severity Severity 1 (Critical) Trap/EventID 2417 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI3003 Message Arguments Virtual MAC address for component at bus arg1 device arg2 function arg3 was successfully programed. • arg1 = bus • arg2 = device • arg3 = func Detailed Description None Recommended Response Action No response action is required.
PCI3004 Message Arguments Device option ROM on mezzanine card arg1 failed to support Link Tuning or FlexAddress. • arg1 = number Detailed Description Either the BIOS, BMC/iDRAC, or mezzanine card firmware is out of date and does not support FlexAddress. Recommended Response Action Update BIOS, BMC/iDRAC, and mezzanine card firmware. If problem persists please contact customer support.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI3006 Message Failed to get Link Tuning or FlexAddress data from iDRAC. Detailed Description Either the BIOS or BMC/iDRAC firmware is out of date and does not support FlexAddress. Recommended Response Action Update BIOS, and BMC/iDRAC firmware. If problem persists please contact customer support.
Subcategory PCI = PCI Device Severity Severity 3 (Informational) Trap/EventID 2419 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI3008 Message Arguments A non-fatal PCIe error detected on a component at bus arg1 device arg2 function arg3 . • arg1 = bus • arg2 = device • arg3 = func Detailed Description System performance may be degraded.
PCI3009 Message Arguments PCIe is operating normally on a component at bus arg1 device arg2 function arg3 . • arg1 = bus • arg2 = device • arg3 = func Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PCI = PCI Device Severity Severity 3 (Informational) Trap/EventID 2419 LCD Message No LCD message display defined.
Subcategory PCI = PCI Device Severity Severity 2 (Warning) Trap/EventID 2418 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI3011 Message Arguments The component at bus arg1 device arg2 function arg3 recovered from a non-fatal IO error. • arg1 = bus • arg2 = device • arg3 = func Detailed Description None Recommended Response Action No response action is required.
PCI3012 Message The QuickPath Interconnect (QPI) width degraded. Detailed Description System performance may be degraded. The bus is not operating at maximum speed or width. Recommended Response Action Reset the system, if the problem persists reinstall processors. Category System Health Subcategory PCI = PCI Device Severity Severity 2 (Warning) Trap/EventID 2418 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable PCI3014 Message Arguments A non-fatal PCIe error detected on a component at slot arg1 . • arg1 = number Detailed Description System performance may be degraded. Recommended Response Action Cycle input power, update component drivers, remove and re-install the device at the next scheduled service time. Category System Health Subcategory PCI = PCI Device Severity Severity 2 (Warning) Trap/EventID 2418 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 2419 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI3016 Message Device option ROM on mezzanine card failed to support Link Tuning or FlexAddress. Detailed Description Either the BIOS, BMC/iDRAC, or mezzanine card firmware is out of date and does not support FlexAddress.
Recommended Response Action No response action is required. Category System Health Subcategory PCI = PCI Device Severity Severity 3 (Informational) Trap/EventID 2419 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI3018 Message New PCI card(s) have been detected in the system. Fan speeds may have changed to add additional cooling to the cards.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PCI3019 Message Arguments A low-severity issue is detected in the SSD bay arg1 , Slot arg2 . • arg1 = bay id • arg2 = slot id Detailed Description A low-severity issue was detected in the SSD bay identified in the message. Recommended Response Action Remove and reinsert the component identified in the message, and then monitor the log for a re-occurrance of the issue.
Detailed Description A low-severity issue is detected in the component identified in the message. Recommended Response Action Remove and reinsert the component identified in the message, and then monitor the log for a re-occurrance of the issue. If the issue persists, and occurs during server startup, update the component firmware. If the issue persists and occurs during OS runtime, restart the server and update the OS drivers for the component identified in the message.
PDR Event Messages 37 PDR1 Message Arguments arg1 copyback stopped for rebuild. • arg1 = physical disk Detailed Description This message is generated after a copyback stops on a physical disk during a rebuild operation. Recommended Response Action Wait for rebuild to finish, then copyback should resume. Category Storage Subcategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined.
Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2065 Server Administrator Trap ID 90100 PDR100 Message Arguments Dedicated Hot Spare arg1 no longer useful for all arrays. • arg1 = PD Name Detailed Description The controller is not able to communicate with a disk that is assigned as a dedicated hot spare. The disk may have been removed.
PDR1000 Message Arguments Drive arg1 is installed in disk drive bay arg2 . • arg1 = number • arg2 = bay Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 2299 LCD Message No LCD message display defined.
Trap/EventID 2297 LCD Message Fault detected on drive in disk drive bay . Check drive. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1002 Message Arguments A predictive failure detected on drive arg1 in disk drive bay arg2 . • • arg1 = number arg2 = bay Detailed Description The controller received a SMART error from the drive. The drive is operational but needs replacement.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1004 Message Arguments Consistency check is in progress for drive arg1 in disk drive bay arg2 .
PDR1005 Message Arguments Drive arg1 in disk drive bay arg2 is in the critical array. • arg1 = number • arg2 = bay Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 1 (Critical) LCD Message Drive in disk drive bay is in the critical array. Replace drive.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1007 Message Arguments Rebuild is in progress for drive arg1 in disk drive bay arg2 . • arg1 = number • arg2 = bay Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR101 Message Arguments Global Hot Spare arg1 does not cover all arrays.
PDR1016 Message Arguments Drive arg1 is removed from disk drive bay arg2 . • arg1 = number • arg2 = bay Detailed Description The controller detected that the drive was removed. Recommended Response Action Verify drive installation. Remove and reseat the failed drive. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Trap/EventID 2299 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1019 Message Arguments Drive arg1 in disk drive bay arg2 is no longer the hot-spare drive. • arg1 = number • arg2 = bay Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action If desired, restart the Patrol Read operation at a later time. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2444 Server Administrator Trap ID 90100 PDR1020 Message Arguments Consistency check for drive arg1 in disk drive bay arg2 completed.
PDR1021 Message Arguments Drive arg1 in disk drive bay arg2 is no longer in the critical array. • arg1 = number • arg2 = bay Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1023 Message Arguments Rebuild completed for drive arg1 in disk drive bay arg2 . • arg1 = number • arg2 = bay Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Recommended Response Action Verify the disk meets the array requirements. Category System Health Subcategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID 2297 LCD Message Drive mismatch detected for drive in bay . Install correct drive type Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1025 Message Arguments Drive mismatch corrected for drive arg1 in disk drive bay arg2 .
PDR103 Message Arguments Cryptographic Erase operation is successfully completed on arg1 . • arg1 = physical disk name Detailed Description Cryptographic Erase operation is successfully completed on the physical disk drive identified in the message. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID 2441 Server Administrator Trap ID 90400 PDR105 Message Arguments arg1 is assigned as dedicated hot-spare. • arg1 = physical disk Detailed Description The physical disk drive identified in the message is assigned as a dedicated hotspare. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
this situation, assigning a new hot spare to maintain data protection in recommended. Recommended Response Action No response action is required. Assigning a new dedicated hot spare to the virtual disk is recommended. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable PDR108 Message Arguments arg1 is unassigned as global hot spare. • arg1 = physical disk Detailed Description A physical disk that was assigned as a hot spare has been unassigned and is no longer functioning as a hot spare. The physical disk was unassigned by a user or automatically by the storage management software.
Recommended Response Action Restart the rebuild operation. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2074 Server Administrator Trap ID 90100 PDR110 Message Arguments The arg1 reliability has degraded.
PDR1100 Message Arguments Drive arg1 is installed. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 2299 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1101 Message Arguments Fault detected on drive arg1 .
LCD Message Fault detected on drive . Check drive. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1102 Message Arguments A predictive failure detected on drive arg1 . • arg1 = number Detailed Description The controller received a SMART error from the drive. The drive is operational but needs replacement. Recommended Response Action The drive will need replacement at the next service window.
Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1104 Message Arguments Consistency check is in progress for drive arg1 . • arg1 = number Detailed Description None Recommended Response Action No response action is required.
PDR1105 Message Arguments Drive arg1 is in the critical array. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 1 (Critical) LCD Message Drive is in the critical array. Replace drive.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1107 Message Arguments Rebuild is in progress for drive arg1 . • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory PDR = Physical Disk Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR111 Message Arguments The volatile memory backup device on arg1 is no longer functional. • arg1 = PCIe solid state device name Detailed Description The volatile memory backup device on the PCIe solid state device identified in the message is no longer functional.
Detailed Description The controller detected a drive removal Recommended Response Action If unintended, verify drive installation. Remove and reseat the indicated disk. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID 2297 LCD Message Drive is removed.
Server Administrator Trap ID Not Applicable PDR1119 Message Arguments Drive arg1 is no longer the hot-spare drive. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1120 Message Arguments Consistency check for drive arg1 completed. • arg1 = number Detailed Description None Recommended Response Action No response action is required.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR1122 Message Arguments Drive arg1 is no longer in the failed array.
PDR1123 Message Arguments Rebuild completed for drive arg1 . • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR114 Message Arguments The arg1 is approaching read-only mode. • arg1 = PCIe solid state device name Detailed Description The PCIe solid state device identified in the message is between 90% and 100% of reaching read-only mode. Recommended Response Action No response action is required.
Category Storage Subcategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID 4345 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR116 Message Arguments Predictive failure reported for arg1 • arg1 = PCIe solid state device name Detailed Description The PCIe Solid-State Drive is predicted to fail.
PDR117 Message Arguments The arg1 has turned off because the critical temperature threshold is exceeded. • arg1 = PCIe solid state device name Detailed Description The PCIe solid state device identified in the message has turned off because the critical temperature threshold of the device was exceeded. Recommended Response Action Contact your service provider for further instructions.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2080 Server Administrator Trap ID 90400 PDR13 Message Arguments arg1 rebuild has failed. • arg1 = physical disk Detailed Description A physical disk included in the virtual disk has failed or is corrupted. In addition, you may have cancelled the rebuild. Recommended Response Action Replace the failed or corrupt disk, and then start the rebuild operation.
Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2089 Server Administrator Trap ID 90100 PDR15 Message Arguments arg1 rebuild is complete. • arg1 = physical disk Detailed Description This message is generated after a rebuild completes on a physical disk.
PDR16 Message Arguments Predictive failure reported for arg1 . • arg1 = physical disk Detailed Description The physical disk is predicted to fail. Many physical disks contain Self Monitoring Analysis and Reporting Technology (SMART). When enabled, SMART monitors the disk health based on indications such as the number of write operations that were performed on the disk. Recommended Response Action Replace the physical disk.
Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2098 Server Administrator Trap ID 90100 PDR18 Message Arguments Global hot spare unassigned from arg1 . • arg1 = PD Name Detailed Description A physical disk assigned as a hot spare was unassigned and is no longer functioning as a hot spare. The physical disk was unassigned by a user or automatically unassigned by Storage Management.
Arguments • arg1 = PD Name Detailed Description A disk on the specified controller has received a SMART alert (predictive failure) indicating that the disk is likely to fail in the near future. Recommended Response Action Replace the disk that has received the SMART alert. If the physical disk is a member of a non-redundant virtual disk, then back up the data before replacing the disk.
Server Administrator Event ID 2198 Server Administrator Trap ID 90300 PDR20 Message Arguments SMART configuration change for arg1 . • arg1 = PD Name Detailed Description A disk has received a SMART alert (predictive failure) after a configuration change. The disk is likely to fail in the near future. Recommended Response Action Replace the disk that has received the SMART alert. If the physical disk is a member of a non-redundant virtual disk, then back up the data before replacing the disk.
Recommended Response Action Remove SSD devices not supported by the controller, and retry the operation. Category Storage Subcategory PDR = Physical Disk Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2382 Server Administrator Trap ID 90300 PDR207 Message Arguments Unable to assign arg1 as a dedicated hot spare.
PDR208 Message Arguments Instant Secure Erase operation successfully completed on arg1 . • arg1 = physical disk name Detailed Description The secure erase operation successfully completed on the Self-Encrypting Drive (SED) identified in the message. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID 2399 Server Administrator Trap ID 90100 PDR21 Message Arguments SMART warning for arg1 • arg1 = PD Name Detailed Description A disk has received a SMART alert (predictive failure). The disk is likely to fail in the near future. Recommended Response Action Replace the disk that has received the SMART alert. If the physical disk is a member of a non-redundant virtual disk, then back up the data before replacing the disk.
are temporarily powered off because power saving option is enabled. 2) The storage controller was not able to update the Configuration On Disk (COD) records on the drive while they were spundown. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
PDR212 Message Arguments The state of arg1 changed from Ready to Non-RAID. • arg1 = physical disk name Detailed Description The physical disk state has changed from Ready state to Non-RAID state. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID 2426 Server Administrator Trap ID 90100 PDR214 Message Arguments The arg1 is not supported because it is not supplied by an authroized hardware provider. • arg1 = physical disk name Detailed Description The physical disk identified in the message is not compliant with the standards set by the hardware provider and is not supported. Recommended Response Action Replace the physical disk with a supported physical disk that is provided by an authorized hardware provider.
Recommended Response Action Retry the Replace Member Disk operation with a different target physical disk. If the problem persists, check the condition of the target physical disk and replace if necessary, then rety the operation. Category Storage Subcategory PDR = Physical Disk Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID 2109 Server Administrator Trap ID 90300 PDR23 Message Arguments SMART warning degraded for arg1 • arg1 = PD Name Detailed Description A disk is degraded and has received a SMART alert (predictive failure). The disk is likely to fail in the near future. Recommended Response Action Replace the disk that has received the SMART alert. If the physical disk is a member of a non-redundant virtual disk, then back up the data before replacing the disk.
Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2111 Server Administrator Trap ID 90300 PDR25 Message Arguments arg1 dead segments are removed. • arg1 = PD Name Detailed Description Portions of the physical disk that were formerly inaccessible have been recovered.
PDR26 Message Arguments arg1 is online. • arg1 = physical disk Detailed Description A drive has entered the online state. This may be because the system just started or could be because a problem with the drive has been corrected. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2160 Server Administrator Trap ID 90100 PDR28 Message Arguments Dedicated hot spare unassigned from arg1 . • arg1 = PD Name Detailed Description A physical disk that was assigned as a hot spare has been unassigned and is no longer functioning as a hot spare. The physical disk was unassigned by a user or automatically unassigned by Storage Management.
Arguments • arg1 = PD Name Detailed Description See A Rebuild Completes with Errors for more information. Recommended Response Action See A Rebuild Completes with Errors for more information. Category Storage Subcategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID 4345 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2163 Server Administrator Trap ID 90400 PDR3 Message Arguments arg1 is not functioning correctly.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR30 Message Arguments A global hot spare failed. arg1 • arg1 = PD Name Detailed Description The controller cannot to communicate with a disk that is assigned as a global hot spare. The disk either failed or was removed. There may also be a bad or loose cable. Recommended Response Action Verify that the disk is healthy and installed. Check the cables.
Recommended Response Action Verify that the disk is healthy and installed. Check the cables. Refer to the product documentation and see the Cables Attached Correctly section for more information on checking the cables. If necessary, replace the disk and reassign the global hot spare. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
Server Administrator Trap ID 90300 PDR33 Message Arguments A dedicated hot spare has been removed. arg1 • arg1 = PD Name Detailed Description The controller cannot to communicate with a disk that is assigned as a global hot spare. The disk either failed or was removed. There may also be a bad or loose cable. Recommended Response Action Verify that the disk is healthy and installed. Check the cables.
Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2205 Server Administrator Trap ID 90100 PDR35 Message Arguments The only hot spare available is a SATA disk arg1 . • arg1 = PD Name Detailed Description The only physical disk available to be assigned as a hot spare is using SATA technology. The physical disks in the virtual disk are using SAS technology.
PDR36 Message Arguments The only hot spare available is a SAS disk arg1 . • arg1 = PD Name Detailed Description The only physical disk available to be assigned as a hot spare is using SAS technology. The physical disks in the virtual disk are using SATA technology. Because of this difference in technology, the hot spare cannot rebuild data if one of the physical disks in the virtual disk fails.
Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2211 Server Administrator Trap ID 90300 PDR38 Message Arguments A clear operation started on arg1 . • arg1 = physical disk Detailed Description A user has initiated a clear operation on a physical disk. Recommended Response Action No response action is required.
Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2251;2437 Server Administrator Trap ID 90100 PDR4 Message Arguments arg1 returned to a ready state.
Server Administrator Trap ID Not Applicable PDR40 Message Arguments The blink operation has ceased on arg1 . • arg1 = physical disk Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2254 Server Administrator Trap ID 90100 PDR42 Message Arguments arg1 has been started. • arg1 = physical disk Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
Detailed Description This message is generated after a clear operation completes on a physical disk. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2269 Server Administrator Trap ID 90100 PDR44 Message Arguments The clear operation on arg1 failed.
Server Administrator Trap ID 90400 PDR46 Message Arguments Patrol Read found an uncorrectable media error on arg1 . • arg1 = physical disk Detailed Description The Patrol Read task has encountered an error that cannot be corrected. There may be a bad disk block that cannot be remapped. Recommended Response Action Backup your data from the disk. Start disk initialization and wait for it to complete, then restore the data from the backup to the disk.
Category Storage Subcategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID 4345 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2273 Server Administrator Trap ID 90400 PDR48 Message Arguments The arg1 rebuild has resumed. • arg1 = physical disk Detailed Description This message is generated after rebuild resumes on a physical disk. Recommended Response Action No response action is required.
Arguments • arg1 = PD Name Detailed Description The dedicated hot spare is not large enough to protect all virtual disks that reside on the disk group. Recommended Response Action Assign a larger disk as the dedicated hot spare. Category Storage Subcategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2049 Server Administrator Trap ID 90300 PDR50 Message Arguments Insufficient space on the global hot spare arg1 . • arg1 = PD Name Detailed Description The global hot spare is not large enough to protect all virtual disks that reside on the controller. Recommended Response Action Assign a larger disk as the global hot spare.
Detailed Description The controller firmware attempted to do SMART polling on the hot spare but could not complete the SMART polling. The controller may have lost communication with the hot spare. Recommended Response Action Verify the health of the disk assigned as a hot spare. Replace the disk and reassign the hot spare. Make sure the cables are attached securely. See the storage hardware documentation for more information on checking the cables.
Server Administrator Trap ID 90300 PDR53 Message Arguments A redundant path has been restored for arg1 . • arg1 = PD Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2285 Server Administrator Trap ID 90100 PDR55 Message Arguments Insufficient space available on the arg1 to perform a rebuild. • arg1 = physical disk Detailed Description The physical disk inserted is too small for the rebuild to occur.
Detailed Description The bad block table is the table used for remapping bad disk blocks. This table fills as bad disk blocks are remapped. When the table is full, bad disk blocks are no longer remapped, which means that disk errors are no longer corrected. At this point, data loss can occur. The bad block table is now 80 percent full. Recommended Response Action Replace the disk generating this message.
Server Administrator Event ID 2307 Server Administrator Trap ID 90400 PDR58 Message Arguments arg1 is incompatible. • arg1 = PD Name Detailed Description A user attempted to replace a disk with another disk that is using an incompatible technology. For example, replaced one side of a mirror with a SAS disk when the other side of the mirror is using SATA technology. Recommended Response Action Refer to the hardware documentation for information on replacing disks.
Recommended Response Action Monitor the disk for other messages or indications of poor health. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2331 Server Administrator Trap ID 90100 PDR6 Message Arguments arg1 is offline. • arg1 = physical disk Detailed Description A physical disk in the virtual disk is offline.
PDR60 Message Arguments Error occurred on arg1 : arg2 . • arg1 = physical disk • arg2 = error code Detailed Description The reason for the error can vary depending on the situation. The firmware error code is indicated in the message. Recommended Response Action Verify the health of attached devices. Review the Lifecycle log for significant events. Replace faulty hardware, if required. Make sure the cables are attached securely.
Trap/EventID 4345 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2347 Server Administrator Trap ID 90400 PDR62 Message Arguments The rebuild failed due to errors on the target arg1 . • arg1 = physical disk Detailed Description It is not possible to rebuild data that resides on a defective disk. Recommended Response Action Replace the target disk.
Detailed Description A write operation cannot complete because the disk contains bad disk blocks that could not be reassigned. Data loss may have occurred. Data redundancy may be lost. Recommended Response Action Replace the disk. Category Storage Subcategory PDR = Physical Disk Severity Severity 1 (Critical) Trap/EventID 4345 LCD Message No LCD message display defined.
Server Administrator Trap ID 90400 PDR65 Message Arguments arg1 is marked as missing. • arg1 = physical disk Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2352 Server Administrator Trap ID 90100 PDR67 Message An unsupported physical disk drive has been detected. Detailed Description The physical disk does not comply with the standards set by service provider and is not supported. Recommended Response Action Replace the physical disk with a supported physical disk.
Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2366 Server Administrator Trap ID 90100 PDR69 Message Arguments Rebuild not possible on arg1 . • arg1 = physical disk Detailed Description Physical disk inserted is of the incorrect protocol.
PDR7 Message Arguments arg1 has degraded. • arg1 = physical disk Detailed Description A physical disk has reported an error condition and may be degraded. The physical disk may have reported the error condition in response to a check consistency or other operation. Recommended Response Action Replace the degraded physical disk. Identify the disk that is degraded by locating the disk that has a red "X" for its status. Perform a rescan after replacing the disk.
Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2060 Server Administrator Trap ID 120100 PDR71 Message Arguments Copyback completed from arg1 to arg2 . • • arg1 = physical disk arg2 = physical disk Detailed Description The copyback operation completed. Recommended Response Action No response action is required.
Detailed Description This alert is provided for informational purposes Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2087 Server Administrator Trap ID 90100 PDR73 Message Arguments Copyback failed from arg1 to arg2 .
Server Administrator Trap ID Not Applicable PDR74 Message Arguments Copyback cancelled on arg1 . • arg1 = physical disk Detailed Description A user cancelled the copyback operation. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2185 Server Administrator Trap ID 90300 PDR76 Message Copyback not possible as SAS or SATA mixing is not supported. Detailed Description Copyback not possible as SAS or SATA mixing is not supported in the same virtual disk. This alert is provided for informational purposes. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR78 Message Arguments arg1 state changed from Non-RAID to READY. • arg1 = physical disk Detailed Description This alert is provided for informational purposes.
PDR79 Message Arguments A user terminated Copyback from arg1 to arg2 . • arg1 = physical disk • arg2 = physical disk Detailed Description A user aborted an ongoing copyback operation. The operation did not complete. Recommended Response Action Re-issue the command. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2052 Server Administrator Trap ID 90100 PDR81 Message Arguments Microcode update started on arg1 . • arg1 = physical disk Detailed Description The physical disk firmware update operation has started. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR83 Message Arguments arg1 is reprovisioned. • arg1 = PD Name Detailed Description This alert is provided for informational purposes.
PDR84 Message Arguments arg1 Security key has changed. • arg1 = physical disk Detailed Description The Security key on a secure encrypted disk was activated. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR86 Message Arguments Bad block table on arg1 is full. • arg1 = physical disk Detailed Description The number of blocks on the disk that exhibit an error has exceeded the capacity of the drive to remap. Any future writes to bad sectors will be unrecoverable. Recommended Response Action Replace the disk.
Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR88 Message Arguments Power state change failed on arg1 .
Server Administrator Trap ID 90400 PDR9 Message Arguments Initialization has started on arg1 . • arg1 = physical disk Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory PDR = Physical Disk Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined.
Severity Severity 3 (Informational) Trap/EventID 4347 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PDR94 Message Arguments Microcode update on arg1 has timed out. • arg1 = physical disk Detailed Description The attempt to update the physical disk has timed out. This may be due to too much activity on the bus, a bad update package, or a bad disk.
Detailed Description The attempt to update the physical disk has failed. This is due to too much activity on the bus, a bad update package, or a bad disk. Recommended Response Action Retry the update. If the update fails a second time, verify the update package is valid. If the update package is valid, replace the failing disk. Contact technical support if the problem persists.
Server Administrator Trap ID Not Applicable PDR97 Message Arguments arg1 security key required. • arg1 = physical disk Detailed Description The controller detected drives that require security keys for access. Without providing security keys, the drives are unstable. Recommended Response Action Provide the security key required to unlock the secure encrypted drives.
Subcategory PDR = Physical Disk Severity Severity 2 (Warning) Trap/EventID 4346 LCD Message No LCD message display defined.
PFM Event Messages 38 PFM0001 Message Arguments The value of arg1 is greater than the upper critical threshold. • arg1 = sensor name Detailed Description The utilization value of the sensor identified in the message is higher than the upper critical threshold. Recommended Response Action Check the work load of the server and reduce the workload if necessary to bring the system performance into required ranges.
Category System Health Subcategory PFM = System Performance Event Severity Severity 2 (Warning) Trap/EventID 2650 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PFM0003 Message Arguments The value of arg1 is less than the lower warning threshold.
Arguments • arg1 = sensor name Detailed Description The value of the sensor identified in the message is within specified limits. Recommended Response Action No response action is required. Category System Health Subcategory PFM = System Performance Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
POW Event Messages 39 POW000 Message Power on permission error, chassis infrastructure not ready. Detailed Description Host failed to power up bacause chassis infrastructure is not ready. This messages has been replaced by Message ID PWR2250 Recommended Response Action Check status of chassis infrastructure. Category Audit Subcategory POW = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default LC Log;None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable POW002 Message Power on permission error, unknown component installed in Fabric1/Fabric2. Detailed Description Host failed to power up because unsupported components installed in Fabric1/ fabric2.This messages has been replaced by Message ID PWR2252 Recommended Response Action Check for unsupported components installed in Fabric1/Fabric2.
LCD Message No LCD message display defined. Initial Default LC Log;None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable POW004 Message Power on permission error, unacknowledge use of 110V. Detailed Description Host failed to power up because of unacknowledged use of 110V. This messages has been replaced by Message ID PWR2254 Recommended Response Action Check for unacknowledged use of 110V.
Severity Severity 2 (Warning) LCD Message No LCD message display defined.
PR Event Messages 40 PR1 Message Arguments A replacement part was detected for device: arg1 • arg1 = device name Detailed Description The specified device has been replaced. Recommended Response Action No response action is required. Category Configuration Subcategory PR = Part Exchange Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Category Configuration Subcategory PR = Part Exchange Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR11 Message A required license for the Part Replacement feature is not present, replacement action(s) will not be performed. Detailed Description A valid license for this feature is not present.
Recommended Response Action No response action is required. Category Configuration Subcategory PR = Part Exchange Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR13 Message Firmware mismatch detected. Configuration changes not applied.
Arguments • arg1 = device name Detailed Description The device identified in the message could not apply the configuration settings. This may indicate configuration changes since the last system inventory. Recommended Response Action Check the current system configuration and retry the operation. Category Configuration Subcategory PR = Part Exchange Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable PR16 Message Arguments Some of the configuration values could not be applied to device: arg1 • arg1 = device name Detailed Description The device could not apply some of the configuration settings. This may indicate configuration changes since the last system inventory or mutually exclusive settings. Recommended Response Action Check the current system configuration and ensure all settings are correct. If not, retry the operation.
Subcategory PR = Part Exchange Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR18 Message Arguments Firmware version difference detected for device: arg1 • arg1 = device name Detailed Description The Part Replacement feature has detected a firmware difference between the current and previous components.
Recommended Response Action No response action is required. Category Configuration Subcategory PR = Part Exchange Severity Severity 3 (Informational) LCD Message No LCD message display defined.
PR20 Message Job in progress. Detailed Description The specified job is in progress. Recommended Response Action No response action is required. Category Configuration Subcategory PR = Part Exchange Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR21 Message Job failed. Detailed Description The specified job did not complete successfully.
Server Administrator Trap ID Not Applicable PR22 Message Preparing new job. Detailed Description This is the initial job status value when a job is created. This message is no longer in use in Lifecycle Controller 2.0 as the job control functionality handles this operation. Recommended Response Action No response action is required. Category Configuration Subcategory PR = Part Exchange Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR24 Message Job cancelled. Detailed Description The specified job was cancelled. This could be due to user action or system error. This message is no longer in use in Lifecycle Controller 2.0 as the job control functionality handles this operation. Recommended Response Action No response action is required.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR26 Message Missing or corrupt job information. Detailed Description The configuration data associated with the specified job could not be located. Recommended Response Action Retry the operation. If this issue persists, contact technical support. Category Configuration Subcategory PR = Part Exchange Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR28 Message Unable to locate device in current configuration. Detailed Description The device that the job was intended for is no longer detected. This could be due to the device being removed, disabled, or a failure. Recommended Response Action If the device was removed, reinsert the device and retry the operation.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR3 Message Arguments Newer version of firmware found on device: arg1 • arg1 = device name Detailed Description The current component firmware version is higher than the replaced component firmware version. Recommended Response Action No response action is required.
Recommended Response Action Enable the Collect System Inventory on Restart attribute of the Lifecycle Controller and restart the system. After the system has restarted, retry the operation. Category Configuration Subcategory PR = Part Exchange Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR31 Message Job completed with errors.
Detailed Description The configuration changes requested, for the indicated job, have not passed the device specific verification check and will not be applied. Recommended Response Action Check the scripts or company documentation and try again Category Configuration Subcategory PR = Part Exchange Severity Severity 2 (Warning) LCD Message No LCD message display defined.
PR34 Message Arguments arg1 failed after exceeding retry attempt limit. • arg1 = job ID Detailed Description The job was attempted but failed unexpectedly. An AC Power loss, system crash, or other interruption during the job processing can cause this failure. Recommended Response Action Recreate and resubmit the job. Category Configuration Subcategory PR = Part Exchange Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR36 Message Arguments Version change detected for arg1 firmware. Previous version: arg2 , Current version: arg3 • arg1 = device name • arg2 = previous version • arg3 = current version Detailed Description The system has detected a different firmware version than previously recorded for the indicated device. This may be due to a firmware update, rollback, or part replacement.
Recommended Response Action No response action is required. Category Configuration Subcategory PR = Part Exchange Severity Severity 3 (Informational) LCD Message No LCD message display defined.
PR6 Message Arguments Configuration changes successfully applied to device: arg1 • arg1 = device name Detailed Description The configuration values stored for the previous device were applied to the current device. Recommended Response Action No response action is required. Category Configuration Subcategory PR = Part Exchange Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PR8 Message Arguments Device not detected: arg1 • arg1 = device name Detailed Description The indicated device has been removed from the system, is no longer functioning, or has been disabled. Recommended Response Action If the part is present, make sure it is properly installed. Ensure that the device has not been disabled in the system BIOS or other configuration utility.
LCD Message No LCD message display defined.
PST Event Messages 41 PST0000 Message Unrecognized Post Code. Detailed Description System post code was never set. Recommended Response Action Do one of the following: 1) Update the iDRAC firmware. 2) Restart the system and retry the operation. If the issue persists, contact your service provider. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message Unrecognized Post Code.
Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0002 Message CPU Microcode load. Detailed Description System BIOS has started loading the processor microcode. Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message CPU Microcode load.
LCD Message Started chipset initialization. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0004 Message Memory Configuration. Detailed Description System BIOS has started memory configuration. Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message Memory configuration started.
Severity Severity 3 (Informational) LCD Message Shadow BIOS operation started. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0006 Message Multiprocessor Initialization. Detailed Description System BIOS has started initialization multiprocessor support. Recommended Response Action No response action is required.
Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message Started power on self test (POST). Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0008 Message System Management Mode (SMM)initialization. Detailed Description System BIOS has started System Management Mode (SMM) initialization. Recommended Response Action No response action is required.
Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message PCI bus enumeration & video initialization. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0010 Message iDRAC is ready. Detailed Description The iDRAC initialization is completed. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message Extended memory test started. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0012 Message Extended Memory test running \ Detailed Description System extended memory test in progress. Recommended Response Action No response action is required.
Detailed Description System extended memory test in progress. Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message Extended Memory test running / Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0014 Message Extended Memory test completed. Detailed Description System completed extended memory test.
PST0064 Message Display sign-on. Detailed Description System BIOS is displaying power on splash screen. Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message Display sign-on. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0065 Message PCI configuration. Detailed Description System BIOS is configuring PCI devices.
Server Administrator Trap ID Not Applicable PST0080 Message An issue was detected. System at boot F1/F2 prompt. Requires entry to continue. Detailed Description System is at the F1/F2 prompt because the system BIOS detected an issue other than "No bootable devices". Recommended Response Action Check post display screen for details. Press F1 to contine boot, or press F2 to go to setup.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0082 Message In BIOS Setup Menu. Detailed Description System is at the BIOS Setup Menu. Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message In BIOS Setup Menu.
Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0084 Message Automated Task application. Detailed Description System started the Automated Task application. Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message Automated Task application.
LCD Message Performing CSIOR. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0086 Message In Lifecycle Controller. Detailed Description System BIOS has launched the Lifecycle Controller user interface. Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message In Lifecycle Controller.
Severity Severity 3 (Informational) LCD Message Initializing iDRAC Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0088 Message Preparing to Boot. Detailed Description System BIOS is preparing to boot the system. Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message Preparing to Boot.
Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0090 Message A problem was detected related to the previous server boot. Detailed Description A problem was detected related to the previous server boot. The next logged message contains more specific details for the detected issue.
Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0126 Message Giving control to UEFI aware OS. Detailed Description System is currently booting to an UEFI compatible operating system. No more POST codes will be generated in this boot sequence.
Recommended Response Action No response action is required. Category System Health Subcategory PST = BIOS POST Severity Severity 3 (Informational) LCD Message Giving control to OS. Initial Default Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0128 Message No memory is detected. Detailed Description System BIOS was unable to detect memory in the system .
PST0129 Message Memory is detected, but is not configurable. Detailed Description System BIOS detected memory, but was unable to configure the memory for system operation. Compare system memory installation to supported system memory configurations. Reduce the system to minimum memory configuration if acceptable. This exception occurred early in system power on, thus the system may not display video.(BIOS POST Exception Code 81).
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0131 Message System BIOS shadow failed. Detailed Description Memory errors occurred copying BIOS image into system memory. This exception occurred early in system power on, thus the system may not display video. (BIOS POST Exception Code 83) Recommended Response Action Remove input power. Reduce system memory to minimum configuration and apply input power.
Severity Severity 1 (Critical) Trap/EventID 2425 LCD Message CMOS failed. Power cycle system Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0133 Message DMA controller failed. Detailed Description System BIOS detected a failure with the DMA controller during system POST. This exception occurred early in system power on, thus the system may not display video.
Recommended Response Action Remove and reapply input power. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory PST = BIOS POST Severity Severity 1 (Critical) Trap/EventID 2425 LCD Message Interrupt controller failed.
PST0136 Message Programmable interval timer error. Detailed Description System BIOS detected an failure with the programmable interval timer during POST. This exception occurred early in system power on, thus the system may not display video.(BIOS POST Exception code 88) Recommended Response Action Remove and reapply input power. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0138 Message SuperIO failed. Detailed Description System BIOS detected a failure with the SIO. This exception occurred early in system power on, thus the system may not display video. (BIOS POST code exception code 8A) Recommended Response Action Remove and reapply input power. If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Severity Severity 1 (Critical) Trap/EventID 2425 LCD Message Keyboard controller failed. Power cycle system Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0140 Message System management interrupt initialization failed. Detailed Description System BIOS failed to initialize the system management interrupt. This exception occurred early in system power on, thus the system may not display video.
Recommended Response Action Reboot the system. If problem persists, remove input power and reseat processors. Category System Health Subcategory PST = BIOS POST Severity Severity 1 (Critical) Trap/EventID 2425 LCD Message QuickPath Interconnect (QPI) fatal error. Contact support Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0142 Message MRC fatal error. Detailed Description BIOS Memory testing failed.
PST0143 Message Intel Trusted Execution Technology (TXT) fatal error. Detailed Description TXT boot failed. This could be related to memory errors or an error with the system TXT configuration. A socketed TPM module may have been removed. This exception occurred early in system power on, thus the system may not display video. Recommended Response Action Check TPM presence. Remove and reapply input power. If the problem persists, contact technical support.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0192 Message Shut-down test failed. Detailed Description System BIOS shutdown test failed during POST. This exception occurred early in system power on, thus the system may not display video. (BIOS POST exception code C0). Recommended Response Action Check system event log for CMOS battery exceptions. Remove and reapply input power. If the problem persists, contact technical support.
Trap/EventID 2425 LCD Message BIOS POST memory test failed. Check memory devices Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0194 Message Remote access controller configuration failed. Detailed Description System BIOS could not configure the Remote Access controller This exception occurred early in system power on, thus the system may not display video.
Recommended Response Action Review system processor configuration and reduce the system to the minimum configuration. Category System Health Subcategory PST = BIOS POST Severity Severity 1 (Critical) Trap/EventID 2425 LCD Message CPU configuration failed. Check screen message Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0196 Message Incorrect memory configuration.
PST0208 Message System BIOS has halted. Detailed Description System BIOS has halted and is unable to continue. Recommended Response Action Do one of the following: 1) If new hardware has been added, remove the new hardware and restart the server, 2) Turn server off and back on using the power button, or 3) Remove and reapply server input power. If the problem persists, contact your service provider. Refer to the product documentation to choose a convenient contact method.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PST0254 Message General failure after video. Detailed Description System BIOS detected a functional or configuration issue during system POST. Check the system video screen for more information. The system event log may contain additional details. This exception occurred early in system power on, thus the system may not display video. (BIOS POST Exception code FE).
Subcategory PST = BIOS POST Severity Severity 1 (Critical) Trap/EventID 2425 LCD Message POST fatal error detected.
PSU Event Messages 42 PSU0000 Message Arguments Power supply arg1 is present. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID 2187 LCD Message No LCD message display defined.
Category System Health Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message PSU failed. Check PSU Initial Default IPMI Alert;LC Log Server Administrator Event ID 5300 Server Administrator Trap ID Not Applicable PSU0002 Message Arguments A predictive failure detected on power supply arg1 . • arg1 = number Detailed Description System performance and power redundancy may be degraded or lost.
Arguments • arg1 = number Detailed Description The power supply is installed correctly but an input source is not connected or is not functional. Recommended Response Action Verify the input source is attached to the power supply. Verify the input power is within the operating requirements for the power supply. Category System Health Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message Power input for PSU is lost.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0005 Message Arguments The power input for power supply arg1 is outside of the allowable range, but it is attached to the system. • arg1 = number Detailed Description The operating requirements for the power supply may be found in product documentation or on the power supply itself. Recommended Response Action Verify the input power is within the operating requirements for the power supply.
Recommended Response Action Review server product documentation for supported power supplies and power supply configurations. Category System Health Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message Power supply is incorrectly configured. Check PSU.
PSU0017 Message Arguments Power supply arg1 is operating normally. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID 2187 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0022 Message Arguments Power supply arg1 is correctly configured. • arg1 = number Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0031 Message Arguments Cannot communicate with power supply arg1 . • arg1 = number Detailed Description The power supply may operate, however power supply monitoring will be degraded.
PSU0032 Message Arguments The temperature for power supply arg1 is in a warning range. • arg1 = number Detailed Description System performance may be degraded. Recommended Response Action Check the system operating environment, including airflow and inlet temperature. Check system logs for temperature and thermal component failures. Category System Health Subcategory PSU = Power Supply Severity Severity 2 (Warning) Trap/EventID 2186 LCD Message No LCD message display defined.
LCD Message PSU temperature outside of range. Check PSU Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0034 Message Arguments An under voltage fault detected on power supply arg1 . • arg1 = number Detailed Description This failure may be the result of an electrical issue with cables or subsystem components in the system. Recommended Response Action 1) Remove and re-install the power supply.
Detailed Description None Recommended Response Action Check input power, replace or re-install the power supply. If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message Over voltage fault on PSU .
Server Administrator Trap ID Not Applicable PSU0037 Message Arguments Fan failure detected on power supply arg1 . • arg1 = number Detailed Description None Recommended Response Action Check for fan blockage. If not replace the power supply. Category System Health Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message Fan failure detected on PSU . Check PSU.
Severity Severity 3 (Informational) Trap/EventID 2187 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0039 Message Arguments An under current fault detected on power supply arg1 . • arg1 = number Detailed Description Insufficient amount of current to keep power supply operating at a normal levels.
Detailed Description The power supply output voltage is insufficient to keep system operating at a normal levels. Recommended Response Action 1) Remove the power supply input cord and then remove power supply. 2) Reinstall the power supply and then re-install the power supply cord. 3) If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Server Administrator Trap ID Not Applicable PSU0042 Message Arguments An output over current fault detected on power supply arg1 . • arg1 = number Detailed Description none Recommended Response Action 1) Remove the power supply input cord and then remove power supply. 2) Reinstall the power supply and then re-install the power supply cord. 3) If the issue persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message Output under current fault detected on PSU . Check PSU. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0044 Message Arguments Cannot obtain status information from power supply arg1 . • arg1 = number Detailed Description The power supply is operating but the system cannot get status information.
Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID 2187 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0046 Message Arguments Communication has been restored to power supply arg1 .
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0076 Message Arguments A power supply wattage mismatch is detected; power supply arg1 is rated for arg2 watts. • arg1 = number • arg2 = value Detailed Description Power supplies should be of the same input type and power rating. Recommended Response Action Install matched power supplies and review product documentation for proper configuration.
Recommended Response Action Install matched power supplies and review product documentation for proper configuration. Category System Health Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID 5354 Server Administrator Trap ID 5354 PSU0078 Message Arguments Power supply arg1 revision mismatch detected.
PSU0080 Message Arguments Power supply arg1 voltage rating does not match the systems requirements. • arg1 = number Detailed Description The system does not support mixed voltage power supplies. Recommended Response Action Review product documentation, change power supply with correct voltage rating. Category System Health Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 2185 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0091 Message Arguments Power supply unit arg1 rating exceeds the system power distribution limits. • arg1 = PSU number Detailed Description The rating of the power supply unit identified in the message should not exceed system power distribution limits.
Detailed Description The rating of the power supply unit identified in the message does not exceed system power distribution limits. Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID 2187 LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0801 Message Arguments Power Supply arg1 : CRC error detected • arg1 = PSU_Name Detailed Description The Power Supply had a CRC error detected Recommended Response Action Aquire the power supply firmware image and update the power supply indicated in the message.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0803 Message Insufficient power in chassis to power on server. Detailed Description Insufficient power in chassis to power on server. Recommended Response Action Utilize the Chassis Management Controller web interface to check available power and server power requirements.
Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0901 Message Arguments Power unit arg1 is on. • arg1 = number Detailed Description None Recommended Response Action No response action is required.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0904 Message Arguments Could not power down 240VA on power unit arg1 .
PSU0906 Message Arguments An interlock power down error detected on power unit arg1 . • arg1 = number Detailed Description In order to meet service requirements the supply must be shut down. Recommended Response Action Remove input power at the power supply. Category System Health Subcategory PSU = Power Supply Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0908 Message Arguments Power lost on power unit arg1 . • arg1 = number Detailed Description The power supply is installed correctly but an input source is not connected or is not functional. Recommended Response Action Verify the input source is attached to the power supply. Verify the input power is within the operating requirements for the power supply.
Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0910 Message Arguments Soft power control failure detected on power unit arg1 . • arg1 = number Detailed Description The system did not respond correctly to a power down request.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0912 Message Arguments A failure detected on power unit arg1 .
PSU0913 Message Arguments Power unit arg1 is operating normally. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU0914 Message Arguments A predictive failure detected on power unit arg1 .
Server Administrator Event ID 5353 Server Administrator Trap ID 5353 PSU100 Message Arguments Power supply arg1 is offline. • arg1 = power supply unit Detailed Description The power supply unit identified in the message is offline, because of the one of the following reasons: 1) The power supply unit is not correctly seated. 2) The power cable may not be connected properly or diconnected. 3) The power supply unit has failed. 4) There is an input power failure.
Recommended Response Action Reconnect the power cable to the power supply unit if it was disconnected. Restore the input AC power supply. Make sure the power supply is restored to the enclosure from the mains. Category Storage Subcategory PSU = Power Supply Severity Severity 2 (Warning) Trap/EventID 4234 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2312;2313 Server Administrator Trap ID 100300 PSU1001 Message Arguments arg1 has failed.
PSU1002 Message Arguments arg1 was removed • arg1 = PSU Sensor Name Detailed Description The enclosure detected that a power supply unit was removed and is no longer functioning in optimal condition. Recommended Response Action Re-insert the power supply unit into the enclosure. Re-connect the AC power cable and switch on the power supply unit. Contact technical support if the issue persists.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU1004 Message Arguments Power supply cable has been inserted into arg1 . • arg1 = PSU Sensor Name Detailed Description The enclosure detected that AC power supply was restored to the power supply unit. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Storage Subcategory PSU = Power Supply Severity Severity 3 (Informational) Trap/EventID 4235 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU1006 Message Arguments arg1 was inserted. • arg1 = PSU sensor name Detailed Description The enclosure detected that a power supply unit was inserted.
PSU1007 Message Arguments arg1 has failed. • arg1 = PSU Sensor Name Detailed Description A device has been failed and the system is no longer functioning in optimal condition. Recommended Response Action Replace the device. Category Storage Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 4233 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default SNMP Alert;OS Log;None Server Administrator Event ID 5353 Server Administrator Trap ID 5353 PSU1010 Message The DC power supply is switched off. Detailed Description The power supply unit is switched off. Either you have switched off the power supply unit or it is defective. Recommended Response Action Check to see whether the power switch is turned off or on. If it is turned off, turn it on.
Recommended Response Action Do one of the following to resolve the issue: 1) reseat the power supply unit. 2) Reconnect the power cable to the power supply unit. 3) Install a new power supply unit 4) Restore the input power supply. Category System Health Subcategory PSU = Power Supply Severity Severity 2 (Warning) LCD Message No LCD message display defined.
PSU500 Message Unable to get the current server power status. Detailed Description Racadm tool cannot obtain the power status possible reason is that the IPMI call failed. Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable PSU502 Message Server is already powered OFF. Detailed Description The server was already down, when the user gave a power off request. Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU504 Message Server power operation successful Detailed Description Success message. Recommended Response Action No response action is required. Category System Health Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) Trap/EventID 8330 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU8515 Message Unable to set the Enable Dynamic Power Supply Engagement attribute. Detailed Description Unable to set the Enable Dynamic Power Supply Engagement attribute. Recommended Response Action Do the following: 1) Retry the operation.
Recommended Response Action Retry the operation after the PSU enumeration is complete. Category Audit Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PSU8517 Message PSU redundancy policy changed. Detailed Description The operation to change the PSU redundancy policy is complete.
Detailed Description The operation to read the FRU data from the PSU identified in the message did not complete successfully due to internal communication errors. Recommended Response Action Retry the operation. If the condition persists, contact your service provider. Category Audit Subcategory PSU = Power Supply Severity Severity 1 (Critical) Trap/EventID 8329 LCD Message No LCD message display defined.
PSU8520 Message Enhanced Dynamic Power Supply Engagement (DPSE) is fully supported. Detailed Description The Dynamic Power Supply Engagement feature is supported and fully operational. Recommended Response Action No response action is required. Category Audit Subcategory PSU = Power Supply Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable 1049
PSUA Event Messages PSUA0016 Message Arguments Power supply arg1 is absent. • arg1 = number Detailed Description The supply has been removed or has failed. Recommended Response Action Install the power supply if needed. Category System Health Subcategory PSUA = PSU Absent Severity Severity 1 (Critical) Trap/EventID 2465 LCD Message PSU is absent.
PWR Event Messages 44 PWR0100 Message The power button was pressed. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR0101 Message The power button was released.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR0102 Message The sleep button was pressed. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR0104 Message The reset button was pressed. Detailed Description The system will reset. Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR0106 Message Arguments The arg1 is latched. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR0108 Message Arguments The arg1 service was requested. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
PWR0109 Message Arguments The arg1 service has completed. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR1000 Message The system performance restored.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR1001 Message The system performance degraded. Detailed Description To avoid shutdown, system performance has been degraded. Recommended Response Action Review system configuration and power consumption. Category System Health Subcategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID 2274 LCD Message System performance degraded.
Trap/EventID 2274 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR1003 Message The system performance degraded because cooling capacity has changed. Detailed Description To avoid shutdown, system performance has been degraded. Recommended Response Action If unintended, review system configuration changes and thermal policy.
Category System Health Subcategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID 2274 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR1005 Message The system performance degraded because of user-defined power capacity has changed. Detailed Description To avoid exceeding the user defined capacity, system performance has been degraded.
Detailed Description The system may shutdown. Recommended Response Action Review system configuration, upgrade power supplies or reduce system power consumption. Category System Health Subcategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID 2273 LCD Message System power exceeds capacity. System halted.
PWR1008 Message The system performance degraded because power draw exceeds the power threshold. Detailed Description To avoid shutdown, system performance has been degraded. Recommended Response Action Review system configuration, upgrade power supplies or reduce system power consumption. Category System Health Subcategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID 2273 LCD Message System power exceeds threshold. Performance degraded.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR200 Message Enabling the Max Power Conservation Mode (MPCM) feature will disable the Extended Power Performance (EPP) feature. Detailed Description Enabling the Max Power Conservation Mode (MPCM) feature will disable the Extended Power Performance (EPP) feature. MPCM forces servers in to a lowpower and limited-performance mode, and then disables the ability to turn on additional servers.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2001 Message The system hard reset. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2003 Message User requested a PXE boot. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2005 Message The OS run-time software initiated a hard reset. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2007 Message System restarted. Detailed Description None Recommended Response Action No response action is required.
Detailed Description Selecting the Server Based Power Management Mode option sets your power cap to a maximum value, server priorities to a default priority, and then disables the Max Power Conservation Mode. Recommended Response Action No response action required. Category System Health Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
PWR203 Message Unable to set the System Input Power Cap value to less than or equal to 13300 W (45381 BTU/h), because the Extended Power Performance feature is enabled. Detailed Description The System Input Power Cap value cannot be set to less than or equal to 13300 W, because the Extended Power Performance feature is enabled. Recommended Response Action Enter a Power cap value greater than 13300 W, and then retry the operation.
Server Administrator Trap ID Not Applicable PWR205 Message The Server Performance Over Power Redundancy (SPOPR) feature cannot be enabled because the Extended Power Performance is enabled. Detailed Description The Server Performance Over Power Redundancy (SPOPR) feature cannot be enabled because the Extended Power Performance is enabled. Recommended Response Action Disable Extended Power Performance and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR207 Message The Dynamic Power Supply Engagement (DPSE) feature cannot be enabled because the Extended Power Performance mode is enabled. Detailed Description The Dynamic Power Supply Engagement (DPSE) feature cannot be enabled because the Extended Power Performance mode is enabled. Recommended Response Action Disable Extended Power Performance and retry the operation.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR210 Message The redundancy policy cannot be changed to either Power Supply Redundancy or No Redundancy because the Extended Power Performance is enabled. Detailed Description The redundancy policy cannot be changed to either Power Supply Redundancy or No Redundancy because the Extended Power Performance is enabled.
Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR213 Message Cannot enable the Extended Power Performance (EPP) mode because the Max Power Conservation Mode (MPCM) is enabled. Detailed Description Cannot enable the Extended Power Performance (EPP) mode because the Max Power Conservation Mode (MPCM) is enabled.
Recommended Response Action DIsable Dynamic Power Supply Engagement (DPSE) and retry the operation. Category System Health Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR216 Message Unable to enable Extended Power Performance, because Redundancy Policy is set to Grid Redundancy or No Redundancy.
Detailed Description Cannot enable the Extended Power Performance (EPP) the feature because the Fresh Air (FA) mode is enabled. Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
PWR220 Message Arguments The Extended Power Performance (EPP) feature cannot be enabled because slot arg1 is empty. • arg1 = slot number Detailed Description The Extended Power Performance (EPP) feature cannot be enabled because the slot identified in the message is empty. Recommended Response Action Insert an appropriate PSU in the slot identified in the message and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2201 Message The system is sleeping with system hardware and processor context maintained. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2203 Message The system is sleeping with system hardware and processor context lost. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2205 Message The system is in a soft-off state. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2208 Message The system is in a sleep state. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR221 Message The Extended Power Performance (EPP) feature is already disabled. Detailed Description The Extended Power Performance (EPP) feature is already disabled. Recommended Response Action No response action is required.
Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2211 Message The system is in legacy ON state. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR222 Message The Extended Power Performance (EPP) feature is already enabled. Detailed Description The Extended Power Performance (EPP) feature is already enabled.
Detailed Description Cannot perform a 110V AC operation because the Extended Power Performance (EPP) feature is enabled. Recommended Response Action Disable the Extended Power Performance (EPP) feature and retry the operation. Category System Health Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
PWR2251 Message Unable to turn on the server because the chassis cover is open. Detailed Description The server did not turn on because the chassis cover is open. Recommended Response Action Close the chassis cover and retry the operation. Category Audit Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable PWR2253 Message Unable to turn on the server because a PCIe card or Mezzanine card is not installed. Detailed Description The server did not turn on because a PCIe card or Mezzanine card is not installed. Recommended Response Action Install a PCI or Mezzanine card in the appropriate slot and retry the operation. Category Audit Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2255 Message The Chassis Managment Controller (CMC) is configured in Max Power Conservation Mode and is unable to grant power on permission to the server. Detailed Description The Chassis Managment Controller (CMC) is configured in Max Power Conservation Mode and is unable to grant power on permission to the server.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log;None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2257 Message Arguments The target power allocation override is arg1 . The target power allocation (AC) is arg2 Watts. • arg1 = override state • arg2 = target power Detailed Description The target power allocation override has been enabled or disabled as identified in the message.
• arg2 = sleep threshold Detailed Description The Power Supply Unit (PSU) hotspare thresholds were modified to the Wake Threshold and Sleep Threshold identified in the message. Recommended Response Action No response action required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
PWR2261 Message Arguments Current Monitor initialization issue observed, IMON Revision arg1 , CPLD IMON MFR Revision arg2 . • arg1 = current monitor revision number • arg2 = CPLD revision number Detailed Description The iDRAC experienced an issue initializing the Current Monitor. The system motherboard may need replacement. Recommended Response Action Contact your service provider.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2263 Message User ignored Power Supply Oversubscription Warning. Detailed Description User continued after receiving power supplyoversubscription warning (F1/F2). Recommended Response Action No response action required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2401 Message Power management firmware initialization error Detailed Description The iDRAC controller detected that the power management firmware did not initialize properly. The system may operate in a performance degraded state. Recommended Response Action "1) Disconnect system input power, wait one minute, reconnect system input power. 2) Re-flash system BIOS.
Category System Health Subcategory PWR = Power Usage Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR2403 Message iDRAC communication with power management firmware has been restored. Detailed Description The iDRAC controller established communication to the power management firmware. System performance will return to normal.
Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR3000 Message The system is being shut down for thermal protection. Detailed Description To avoid system damage because of insuffecient cooling, the system is being shut down.
Detailed Description The system has detected a new peak power value. Recommended Response Action Make sure that the power usage corresponds to the the current hardware configuration and workload. Category System Health Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable PWR8501 Message Arguments Successfully set Virtual Infrastructure Device power to arg1 WDC • arg1 = power reading Detailed Description Power allocation succeeded for Virtual infrastructure. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8504 Message Chassis power button is pressed, but the button is disabled. Detailed Description The chassis power button press is detected but the button has been disabled. Recommended Response Action The chassis power button is disabled.
Category Audit Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8506 Message Arguments Cumulative power computation (KWH) time is reset on arg1 . • arg1 = time Detailed Description Resetting the power computation reading causes the log to report time at which it is reset.
Detailed Description The system Input Power Cap was changed from the value to the value indicated in the message. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
PWR8509 Message Unable to change the server power priority because Server Based Power Management mode is enabled. Detailed Description Unable to change the server power priority because Server Based Power Management mode is enabled. Recommended Response Action The server power priority can be changed once Server Based Power Management mode is disabled. Using the CMC Web UI, navigate to the Chassis Overview > Power > Configuration page, then uncheck the Enable Server Based Power Management checkbox.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8511 Message Unable to set the CHASSIS_POWER_button_disable chassis power property. Detailed Description Unable to set the CHASSIS_POWER_button_disable chassis power property. Recommended Response Action Retry the operation. If the issue persists, contact your service provider. Category Audit Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8514 Message Unable to perform chassis power action due to insufficient privileges. Detailed Description The user account credentials provided for this chassis power action do not have the correct privilege. Chassis control privilege is required to perform chassis power actions.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8516 Message Unable to perform the chassis power action requested.. Detailed Description Unable to perform the chassis power action requested. Recommended Response Action Check the tracelog for more information. If the issue persists, contact your service provider.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8518 Message Unable to perform the chassis power action because the chassis is already turned on. Detailed Description Unable to perform the chassis power action because the chassis is already turned on. Recommended Response Action No response action is required.
Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8520 Message Initiated the chassis reset operation. Detailed Description The chassis reset operation was initiated. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8522 Message Initiated chassis power cycle operation. Detailed Description The chassis power cycle operation was initiated. Recommended Response Action No response action is required.
Detailed Description The chassis power cycle operation was completed. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8524 Message Redundancy was lost, while Server Performance Over Power Redundancy is enabled.
PWR8525 Message 110VAC Operation acknowledged. Detailed Description 110VAC operation of PSUs is acknowledged. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8526 Message 110VAC Operation unacknowledged.
Server Administrator Trap ID Not Applicable PWR8527 Message Server slot power priorities changed - reallocating power. Detailed Description Server slot power priorities were changed. Power to servers is being reallocated. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8529 Message Max Power Conservation Mode is enabled. Detailed Description The Max Power Conservation Mode is enabled. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8531 Message Server Based Power Management Mode is enabled. Detailed Description Server Based Power Management Mode is enabled. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8533 Message Arguments Power cap changed from arg1 W AC to arg2 W AC. • arg1 = power value • arg2 = power value Detailed Description Power cap setting was changed. Recommended Response Action No response action is required.
Category Audit Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8535 Message Unable to set Server Based Power Management Mode to disable. Detailed Description Unable to set Server Based Power Management Mode to disable. Recommended Response Action Retry the operation. If the issue persists, contact your service provider.
Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8537 Message Server Performance Over Power Redundancy is disabled. Detailed Description Server Performance Over Power Redundancy is disabled.
Detailed Description Power Remote Logging is enabled. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8539 Message Power Remote Logging is disabled. Detailed Description Power Remote Logging is disabled.
PWR8540 Message Arguments Power Remote Logging Interval set to arg1 • arg1 = interval Detailed Description The interval for remote logging of power information is set to the value identified in the message Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable PWR8542 Message Chassis powerup operation completed. Detailed Description Chassis powerup operation completed. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8544 Message Arguments Chassis Management Controller turned off the Server arg1 because of insufficient power at inventory. • arg1 = slot number Detailed Description Insufficient power is available for the server identified in the message to function.
Detailed Description Incorrect power inventory information reported by the iDRAC for the server identified in the message. Recommended Response Action Invalid power inventory information could be due to outdated iDRAC firmware or server BIOS firmware versions. Update the components to their latest versions. Category Audit Subcategory PWR = Power Usage Severity Severity 1 (Critical) LCD Message No LCD message display defined.
PWR8547 Message Chassis is already powered off. Detailed Description The chassis was already turned off, when the power off request was received. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable PWR8549 Message Chassis shutdown did not complete successfully. Detailed Description The requested chassis shutdown operation did not complete successfully. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8551 Message Arguments Successfully set Virtual Infrastructure Device power to arg1 DC Watt. • arg1 = power reading Detailed Description This will be logged when a Virtual Infrastructure Device power allocation is configured. Recommended Response Action No response action is required.
Recommended Response Action Make sure there is enough power supply to distribute power. Using the CMC Web UI, go to Chassis Overview > Power > Power Budget Status. In the Total Input Power Available For Allocation field view the available power. To add more power, insert more PSUs or remove unused components from the chassis. Contact your service provider for information on the power required for the component identified in the message.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8555 Message Arguments Chassis Management Controller unable to turn on arg1 - arg2 at priority arg3 because of insufficient power. Minimum power needed is arg4 AC Watt, but only arg5 AC Watt is available.
Arguments • arg1 = slot number Detailed Description The Server identified in the message was shutdown due to insufficient power. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID 8417 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8558 Message The System Input Power Cap is being enforced with the current Power Supply configuration. Detailed Description A configuration change has occurred such that the current power cap is now supported. Recommended Response Action No response action is required.
Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8560 Message Arguments Unable to turn on I/O Module arg1 due to insufficient chassis power. • arg1 = IOM slot name Detailed Description Unable to turn on the I/O Module identified in the message due to insufficient chassis power.
Detailed Description The Chassis Management Controller is unable to communicate with the Server iDRAC service processor and the server could not be powered on. This situation may occur when iDRAC is rebooting. Recommended Response Action Wait for three minutes and then retry the operation. If the issue persists, remove and reinsert the server and wait for the iDRAC to finish restarting.
Server Administrator Trap ID Not Applicable PWR8563 Message Arguments Unable to turn on Server arg1 due to I/O fabric inconsistency. • arg1 = server number Detailed Description The Server identified in the message did not turn on due to a fabric mismatch between the I/O Module and the Mezzanine card on the Server. Recommended Response Action Make sure that the hardware compatibility between the I/O Module (IOM) and the Mezzanine (Mezz) card is correct.
Subcategory PWR = Power Usage Severity Severity 2 (Warning) Trap/EventID 8418 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8565 Message Arguments Unable to turn off the Server arg1 due to iDRAC communication issue.
PWR8566 Message Arguments Unable to turn off the Server arg1 before the Power Off timer expired. • arg1 = server number Detailed Description Unable to turn off the Server before the Power Off timer has expired. This happens if the Server did not show "power off" status change within 30 seconds after the operation was initiated. This situation may also occur when iDRAC is rebooting. Recommended Response Action The Server may need more time to turn off. Wait for ten seconds and check the power status.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8568 Message Arguments Server arg1 did not gracefully shutdown before the timer expired. • arg1 = slot number Detailed Description The server identified in the message did not gracefully shutdown before the CMC shutdown timer expired.
Recommended Response Action Turn on the server, if necessary, before requesting a power cycle operation. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8570 Message Arguments Unable to communicate to the iDRAC, when trying to power cycle the server arg1 .
PWR8571 Message Arguments Unable to perform the power action requested for the server arg1 because another power action is in progress. • arg1 = server idr Detailed Description Another power action is in progress. The requested power action cannot be carried out until the power action in progress completes Recommended Response Action Wait for the power action in progress to complete and retry the operation. It may take a few minutes for the current power action to complete.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8573 Message Arguments The Chassis Management Controller is unable to communicate to the iDRAC, when trying to turn off the server arg1 . • arg1 = server id Detailed Description The Chassis Management Controller is not able to communicate with the iDRAC on the server identified in the message. Therefore the server could not be turned off. This situation may occur when iDRAC is restarting.
Recommended Response Action Wait for three minutes, and then retry the operation. If the issue persists, remove and reinsert the server and wait for the iDRAC to finish restarting before retying the operation. Category Audit Subcategory PWR = Power Usage Severity Severity 1 (Critical) Trap/EventID 8417 LCD Message No LCD message display defined.
PWR8576 Message Arguments Unable to turn on the Sleeve or Sled arg1 after a virtual reseat operation. • arg1 = slot number Detailed Description The virtual reseat initiated on the Sleeve or Sled identified in the message successfully turned off the component. However, the Sleeve or Sled did not turn on successfully. A virtual reseat is the same as removing and inserting a Sleeve or Sled. Recommended Response Action Retry the virtual reseat operation on the Sleeve or Sled identified in the message.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8578 Message Arguments Chassis Management Controller is unable to turn on the iDRAC on server- arg1 because power required is less than available power. • arg1 = slot number Detailed Description The Chassis Management Controller is unable to turn on the iDRAC because power required is less than available power.
Detailed Description A request to reset the CMC identified in the message is initiated. If a second CMC is present, a failover to the other CMC will occur as a result. Recommended Response Action No response action is required. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
PWR8581 Message Arguments Chassis Management Controller is unable to turn on server- arg1 because another chassis power operation is in progress. • arg1 = slot number Detailed Description A chassis power operation is currently in progress and the server identified in the message could not be turned on. Recommended Response Action Wait until the current chassis power operation is complete and the chassis is On and then retry the operation.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8583 Message Arguments Chassis Management Controller is unable to turn on server- arg1 because unacknowledged 110V PSUs are present. • arg1 = slot number Detailed Description To enable 110V operation, the Allow 110VAC Operation feature must be enabled. If the feature is not enabled, the server turn-on operation will not be processed.
Detailed Description If power redundancy is lost and the server Performance Over Power Redundancy feature is disabled, the server turn-on will not be allowed. Recommended Response Action To enable the server to be turned-on, on the Power Configuration page in the Web UI, enable the server Performance Over Power Redundancy option . Using the RACADM utility, run the following command "racadm config -g cfgChassisPower o cfgChassisPerformanceOverRedundancy 1". Then retry the operation.
PWR8586 Message Arguments Chassis Management Controller is unable to turn on server- arg1 because it is not supported in the VRTX chassis. • arg1 = slot number Detailed Description The Chassis does not support the server identified in the message. Recommended Response Action The server inserted is not supported in the Chassis. Remove the server from the Chassis. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8588 Message Arguments Chassis Management Controller is unable to turn on server- arg1 because a chassis infrastructure firmware update is in progress. • arg1 = slot number Detailed Description The server identified in the message cannot be turned on while a chassis infrastructure firmware update operation is in progress.
Recommended Response Action Insert a PCIe Mezzanine card in slot B1. Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8590 Message Arguments The server- arg1 does not have PCIe Mezzanine card in slot C1. • arg1 = slot number Detailed Description The PCIe Mezzanine card in the slot C1 is absent.
PWR8591 Message Servers are turned off to allocate power to the newly inserted hard disk drives. Detailed Description Before inserting hard disk drives, always make sure the Chassis has enough available power. Otherwise operating servers may be turned off. Recommended Response Action Make sure there is enough power supply to distribute power. Go to, the Chassis Overview > Power > Power Budget Status. In the Total Input Power Available For Allocation field, view the available power.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8593 Message Chassis Management Controller is unable to turn on or turn off the chassis because the chassis infrastructure component firmware update is in progress. Detailed Description The chassis power operation cannot be performed when a chassis infrastructure firmware update is in progress.
Category Audit Subcategory PWR = Power Usage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8595 Message Arguments Chassis Management Controller is unable to turn on server arg1 due to insufficient power for the arg2 .
PWR8596 Message Arguments Chassis Management Controller is unable to turn on server- arg1 because PSU redundancy is lost and the available power is insufficient. • arg1 = slot number Detailed Description The Chassis Management Controller cannot turn on the server identified in the message, because PSU redundancy is lost or PSUs are removed. Sufficient power is not available for the operation. Recommended Response Action Make sure there is enough power supply to distribute power.
Severity Severity 1 (Critical) Trap/EventID 8417 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8598 Message Arguments The Power Supply Unit (PSU) arg1 is turned off because it is not compatible with the other PSUs used in the Chassis.
Detailed Description The Power buttons for all multinode sleds in the chassis are disabled. This operation is only applicable to the multinode sleds available, and does not affect other servers in the chassis. Recommended Response Action The multinode sled power button is disabled. To enable the chassis power button use the CMC RACADM command line interface, CMC Web interface. Using the command line, enter "racadm config -g cfgChassisPower -o cfgChassisSledPowerButtonEnable 1".
Server Administrator Trap ID Not Applicable PWR8654 Message Arguments Chassis Management Controller (CMC) is unable to send power allocation information to the component arg1 - arg2 . • arg1 = component name • arg2 = component id Detailed Description CMC could not successfully send the power allocation information to the component identified in the message, because either iDRAC is stopped after the power allocation was sent by CMC or the communication between CMC and iDRAC has ended.
Detailed Description CMC could not successfully turn on the component identified in the message, because of insufficient power available. Recommended Response Action Make sure there is sufficient power available, and then retry the operation. To view the available power, on the CMC Web interface, click Chassis Overview > Power > Power Budget Status. The available power is displayed in the Total Input Power Available For Allocation field.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8664 Message Arguments The Dynamic Power Supply Engagement feature is arg1 • arg1 = enabled/disabled Detailed Description The power configuration property dynamic power supply engagement feature is disabled or enabled Recommended Response Action No response action is required Category Configuration Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display d
Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8666 Message iKVM power cycle initiated.
Category Audit Subcategory PWR = Power Usage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8668 Message iKVM reset initiated.
Detailed Description The server identified in the message could not be successfully turned on because of incompatibility between the chassis PCIe components and mezzanine card. Recommended Response Action Make sure that the chassis PCIe components and mezzanine card are compatible. For information about compatibility of hardware components, see the Modular System Chassis Hardware Manual.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable PWR8671 Message Arguments The Chassis Management Controller is unable to set the Enhanced Cooling Mode because the requested power arg1 AC Watts exceeds the subsystem power limit arg2 AC Watts for IO Modules, Blowers and Servers.
RAC Event Messages 45 RAC001 Message The command was successful. Detailed Description The command was successful. Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC002 Message General failure.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC003 Message Arguments Missing required parameter arg1 . • arg1 = parameter name Detailed Description One or more required parameters for the method are missing. Recommended Response Action Refer to the profile document and provide the required parameters.
Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC005 Message Mismatch in AttributeName and AttributeValue count. Detailed Description The name value pairs do not match in the input specified in the method invocation parameters.
Recommended Response Action Set an Attribute that is not ReadOnly. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description The attribute boolean value is not valid for the specified attribute. Recommended Response Action Provide valid boolean value for the specified attribute. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC009 Message String exceeds maximum length.
RAC010 Message Invalid character value. Detailed Description The input value for the attribute being set contains characters that are not allowed. Recommended Response Action Retry the operation with valid characters for the specified attribute. Refer to the Lifecycle Controller-Remote Services documentation. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0101 Message The inserted Smart Card is not valid or the Smart Card reader is not supported. Detailed Description The data returned is not in a known format. Recommended Response Action This error may occur because: 1. Smart Card is invalid. Insert a valid Smart Card and try again. 2. Check connection between reader and system. 3. There may be an issue with the Smart Card reader. Try reinstalling the reader driver or use a different reader.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0103 Message This browser does not support Smart Card logon on iDRAC. Use Internet Explorer version 7.0 or later to use this feature. Detailed Description Smart Card login is only supported in newer versions of Internet Explorer. Recommended Response Action See the iDRAC help text or documentation for a list of supported browsers.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0105 Message The Smart Card reader cannot be detected. Check whether the reader is installed correctly. Detailed Description Communication with the Smart Card reader cannot be established, or is lost. Recommended Response Action This error may occur because: 1. Check connection between reader and system. 2. There may be an issue with the Smart Card reader.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0107 Message The inserted Smart Card cannot be recognized. Ensure that the correct Smart Card CSP drivers are installed. Detailed Description Communication with the Smart Card reader is established and a Smart Card is inserted, but there are problems accessing the Smart Card.
Recommended Response Action Review the error message preceeding or following this message. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC011 Message Job already exists, cannot process more set operations. Detailed Description Job has already been scheduled to apply pending iDRAC attribute values.
Detailed Description Data entered is not an integer value in the valid range of numbers. Recommended Response Action Enter a Remote Syslog Port number. Expected range: [1-65535 or 0x1-0xFFFF] Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0115 Message The Destination IP Address value is invalid.
RAC0116 Message Invalid Destination IPv6 Address. Detailed Description The entered IPv6 address does not conform to the addressing standard or the supported IPv6 address range. Recommended Response Action Enter a valid Destination IPv6 Address. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0118 Message Unsupported vFlash SD card detected. Detailed Description The SD card is not a valid vFlash SD card. The use of non-Dell media prevents the use of some extended capabilities and functions. Recommended Response Action Insert a supported vFlash SD card. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0120 Message The selected partition size exceeds the available space. Detailed Description Requested partition size exceeds the available space. Recommended Response Action Enter a partition size smaller than the unused space on the vFlash SD card. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0124 Message Invalid label: Label must be exclusively alphanumeric characters. Detailed Description All characters in the label must be alphanumeric. Recommended Response Action Enter all alphanumeric characters. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0127 Message The specified size must be a non-fractional numeric value. Detailed Description Size must be a whole number. Recommended Response Action Enter a whole number for the size field. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0129 Message An error has occurred while initializing the SD card. Detailed Description No status response was returned after completing the initialization request. Recommended Response Action Try reinitalizing the card again in a few minutes.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0130 Message An error has occurred while creating a partition. Detailed Description A seperate message will provide more detail about this error which was detected while creating the vFlash partition. Recommended Response Action No response action is required.
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0132 Message An error has occurred while formatting a partition. Detailed Description A seperate message will provide more detail about this error which was detected while formatting the vFlash partition.
Recommended Response Action Try downloading the partition again in a few minutes. If the problem persists, reset iDRAC before trying the operation again. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0134 Message This operation is unavailable for non-vFlash SD cards.
Detailed Description A seperate message will provide more detail about this error which was detected while detaching the vFlash partition. Recommended Response Action No response action is required. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC0137 Message An error has occurred while changing the read-write state for the partition. Detailed Description A seperate message will provide more detail about this error which was detected while changing the read-write state of the vFlash partition. Recommended Response Action No response action is required. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC014 Message Invalid Attribute was entered. Detailed Description The attribute name provided is not valid for the current method. Recommended Response Action Provide valid attribute and retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0141 Message Firmware update verification failed: The update status is unknown. Detailed Description Firmware update verification process failed; the firmware update status is unknown. Recommended Response Action Verify if the firmware has been updated by checking the new firmware version number. If it has not been updated try the firmware update again in a few minutes.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0146 Message Firmware rollback has failed. Detailed Description Firmware rollback operation failed. Recommended Response Action Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0148 Message Unable to retrieve the batteries information. The system is powered off. Detailed Description While the system is powered off it is unable to retrieve information about the batteries. Recommended Response Action Turn the system on to view this information.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC015 Message Arguments Not one of the Possible Values for AttributeName arg1 . • arg1 = attribute name Detailed Description The attribute value is not valid for the attribute identified in the message.
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0151 Message Unable to retrieve the removable flash media information. The system is powered off. Detailed Description While the system is powered off it is unable to retrieve information about removable flash media.
Recommended Response Action Turn the system on to view this information. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0153 Message Non-redundant power mode: Check the system hardware manual for implications.
Detailed Description Displayed when a group of redundant power supplies has one or more individual power supplies with bad status. Recommended Response Action Replace the degraded power supply unit. Check the Power Supplies page for more information. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC0156 Message Unable to retrieve the voltage information. The system is powered off. Detailed Description While the system is powered off it is unable to retrieve information about system voltage. Recommended Response Action Turn the system on to view this information. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0159 Message Certificate upload failed: No pending CSR or private key. Detailed Description Certificate upload failed because there is no pending Certificate Signing Request (CSR) or private key. Recommended Response Action Upload failed due to no pending Certificate Signing Request (CSR). Try creating a new CSR and then upload the certificate.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0160 Message Certificate upload failed: Cannot validate the certificate. Detailed Description Certificate upload failed because the certificate could not be validated. Recommended Response Action Certificate may be corrupt. Try creating a new Certificate Signing Request (CSR) and then upload the certificate.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC017 Message Job created to apply the attribute value. Detailed Description The requested job has been created. Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC018 Message Job completed with Errors. Detailed Description All the tasks in the Job were attempted, but some did not complete successfully. Recommended Response Action Examine source of the errors by inspecting the results from the job execution, and after resolving the issues, retry the operation.
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC019 Message Job did not complete successfully. Detailed Description The submitted job did not complete successfully.
Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0206 Message Certificate upload failed: Not a certificate file. Detailed Description Certificate upload failed because this is not a certificate file.
Detailed Description Certificate upload failed possibly due to poor network connection. Recommended Response Action Try the operation again in a few minutes. If the problem persists, issue a new Certificate Signing Request (CSR) and try again. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC0209 Message Certificate upload failed: iDRAC unable to upload at this time. Detailed Description Certificate upload failed because iDRAC unable to upload at this time. Recommended Response Action Try the operation again in a few minutes. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0211 Message Firmware update has failed. Detailed Description Firmware update has failed. This may be due to a corrupt firmware image, poor network connection, or another issue. Recommended Response Action Download a new firmware image and try loading the firmware again. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0213 Message Missing Username. Detailed Description Login page is missing a username. Recommended Response Action Enter a valid username. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0215 Message Login failed: User does not have Login to iDRAC privilege. Detailed Description Login failed because the user does not have Login to iDRAC privilege. Recommended Response Action Login to iDRAC privilege is needed. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0217 Message iDRAC is not responding. Detailed Description Client did not receive a response for the login request. Recommended Response Action Try pinging the iDRAC and then try again. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0219 Message Power command failed. Detailed Description Requested power state change has failed. Recommended Response Action Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0221 Message The Destination E-mail Address is too long. The maximum length is 64 characters. Detailed Description The Destination E-mail Address can contain upto 64 characters. Recommended Response Action Enter an email address that contains upto 64 characters.
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0223 Message Enter an alphanumeric value or a valid symbol for the following (see the online help for more information): Detailed Description The Subject line in the email contains invalid characters. Recommended Response Action Invalid character.
Recommended Response Action Enter a valid email description. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0225 Message Sending the test mail failed. Detailed Description Sending the test mail failed. This will prevent alert messages from being sent to this email address.
Detailed Description Sending the test mail failed. This will prevent alert messages from being sent to this email address. Recommended Response Action Confirm that: 1. A valid SMTP server address is configred in the iDRAC. 2. The remote email server is configured properly to send and receive emails. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC0228 Message SD Card is detected with an unrecognized format. Click Initialize to initialize the card. Detailed Description SD Card needs to be formatted to make it usable. The card must be initialized. Recommended Response Action Click Initialize to initialize the card and make it usable. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0230 Message This operation erases all data in the SD Card. Do you want to continue? Detailed Description This message is displayed when a confirmation is required to initialize the vFlash SD Card. Recommended Response Action Press OK to initialize the SD Card. This will erase all data. If undesired press Cancel. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0235 Message vFlash image upload timed out. Detailed Description When uploading an image to the vFlash partition, the operation is unresponsive, and has timed out. Recommended Response Action Try uploading the vFlash image again. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0237 Message An error occurred while uploading the vFlash image. Detailed Description A seperate message will provide more detail about this error which was detected while uploading the vFlash image. Recommended Response Action Try uploading the vFlash image again.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0239 Message SD Card is write-protected. Detailed Description The contents of a write protected SD Card cannot be modified. Recommended Response Action Make sure the SD Card is not write-protected before attempting to change its contents.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0240 Message vFlash is disabled. Detailed Description vFlash needs to be enabled before attempting this operation. Recommended Response Action Enable vFlash before trying the operation.
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0242 Message The selected partition does not exist. Detailed Description The vFlash partition does not exist. This may be due to another user deleting that partition. Recommended Response Action Refresh the Web GUI page to see the available partitions.
Recommended Response Action There was a conflict with a concurrent session. Refresh the page to see the currently available options. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0244 Message The partition label must be unique.
Detailed Description The vFlash partition is in-use by another process. Therefore, the current operation cannot proceed. Recommended Response Action Try the operation after a few minutes or with another partition. If the problem persists, reset iDRAC and repeat the operation. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC0247 Message The partition is currently attached. Detailed Description This message is displayed when trying to format or download to an attached vFlash partition. Recommended Response Action Detach this partition and try again. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0249 Message One or more partitions are in-use by another process. Detailed Description The vFlash partition is in-use by another process. Therefore, the current operation cannot proceed. Recommended Response Action Try the operation after a few minutes. If the problem persists, reset iDRAC and repeat the operation. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0250 Message One or more partitions are read-only. Detailed Description The vFlash partitions are read-only. Therefore, the current operation cannot proceed. Recommended Response Action Make sure the partitions are writable before attempting to change their contents. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0252 Message One or more partitions are currently detached. Detailed Description The vFlash partitions are detached Therefore, the current operation cannot proceed. Recommended Response Action Attach the partitions and try again. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0254 Message The Gateway Address is invalid. Expected range: [0.0.0.0 or 1.0.0.0 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0256 Message The Preferred DNS Server Address is invalid. Expected range: [0.0.0.0 or 1.0.0.0 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)].
Recommended Response Action Enter a valid Alternate DNS Server Address. Expected range: [0.0.0.0 or 1.0.0.0 223.255.255.255 excluding: 127 (first octet), 0 or 255 (last octet)]. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0259 Message Invalid IPv6 address.
Detailed Description Unable to set DNS Domain Name because "Domain Name From DHCP" is Enabled. Recommended Response Action Disable "Domain Name From DHCP" to set values for DNS Domain Name. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0260 Message Invalid IPv6 prefix length. Expected range: 0-128.
RAC0261 Message Invalid IPv6 gateway address. Detailed Description This error message is displayed to indicate that the IPv6 gateway address does not conform to the required format. Recommended Response Action Enter a valid IPv6 gateway address. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0263 Message The Alternate IPv6 DNS Server Address is invalid. Detailed Description This error message is displayed to indicate that the Alternate IPv6 DNS Server address does not conform to the required format. Recommended Response Action Enter a valid Alternate IPv6 DNS server address. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0266 Message Invalid VLAN ID. Expected range: 1-4094. Detailed Description Specify a valid VLAN ID. Recommended Response Action Enter a valid VLan ID. Expected range: 1-4094. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0268 Message NIC is disabled. Detailed Description The NIC is disabled. This may adversely affect the current operation, and might not allow subsequent GUI interactions to this NIC. Recommended Response Action Enable the NIC before performing the operation. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC027 Message Unable to set values for Speed or Duplex because Auto Negotiation is Enabled. Detailed Description Unable to set static values for Speed or Duplex when the Auto Negotiation attribute is enabled. Recommended Response Action Disable Auto Negotiation in order to set values for Speed or Duplex.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0271 Message Continuing will lock user account. Detailed Description Locking the user account prevents them from gaining access to iDRAC. Recommended Response Action Press OK to lock this user account. This action will prevent future access for this user. If undesired press Cancel.
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0273 Message iDRAC access will be limited to running the Racadm utility on the local server or using the serial interface. Detailed Description If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled.
Recommended Response Action See iDRAC user documentation for more information on using racadm. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0275 Message Click OK to disable the NIC. Click Cancel to keep the setting unchanged.
Detailed Description If the the Enable NIC checkbox is cleared, remote access to iDRAC is disabled. Recommended Response Action Click Apply to save changes. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0277 Message Disabling IPv4 prevents access to iDRAC using an IPv4 address.
RAC0278 Message Disabling IPv6 prevents access to iDRAC using an IPv6 address. Detailed Description This warning message appears when IPv6 is disabled. Recommended Response Action Use IPv4 network to access iDRAC remotely. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC028 Message Unable to Enable "DNS Domain Name From DHCP" or "DNS From DHCP" because DHCP is Disabled. Detailed Description The attributes "DNS Domain Name From DHCP" and "DNS From DHCP" are dependent on the attribute DHCP being Enabled. Currently DHCP is configured as Disabled. Recommended Response Action Set DHCP attribute to Enable to be able to Enable DNS Domain Name From DHCP or DNS From DHCP.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0281 Message The IP Subnet Mask is invalid. Expected range: 0.0.0.0 - 255.255.255.255. Detailed Description This error message is displayed to indicate that the IP Subnet Mask does not conform to the required format. Recommended Response Action Enter a valid IP Subnet Mask. Expected range: 0.0.0.0 - 255.255.255.255.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0283 Message IP Blocking Fail Window is invalid. Expected range: 10-65535. Detailed Description This is the time span (in seconds) within which IP Blocking Fail Count failures must occur to trigger the IP Blocking Penalty Time. The default value is 3600 seconds (1 hour). Recommended Response Action Enter a valid IP Blocking Fail Window. Expected range: 10-65535.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0285 Message User name cannot be empty. Detailed Description The user name cannot be empty when creating a user account. Recommended Response Action Enter a user name. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0288 Message Invalid entry: Entry must be exclusively alphanumeric characters and valid symbols. Detailed Description All characters entered must be alphanumeric or valid symbols. Recommended Response Action Enter all alphanumeric characters and valid symbols.
Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC029 Message Required dependency not found in input. Detailed Description The input is missing required dependencies necessary for the operation.
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0291 Message The user name cannot contain: /, \, @, ., or " (quotation mark). Detailed Description The user name value does not accept these characters. Recommended Response Action Do not enter /, \, @, ., or " (quotation mark) for user name.
Recommended Response Action Load a valid certificate. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0293 Message When certificate validation is enabled, a valid root Certificate Authority (CA) certificate must be uploaded. The CA certificate is used to verify the directory server SSL certificate.
Detailed Description The amount of time iDRAC waits before sending a partial Serial Over LAN (SOL) data packet. This parameter is specified in milliseconds. It is recommended to use 10 milliseconds for optimal performance. Recommended Response Action Enter a valid Character Accumulate Interval value. Expected range: 1-255. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0297 Message Specify a Domain Controller Address must be configured. Detailed Description The Domain Controller Address be specified for Active Directory configuration. Recommended Response Action Enter a valid Domain Controller Address. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC030 Message The Required attribute that this Attribute is dependent on has an incorrect value. Detailed Description The attribute value provided for the Required attribute is invalid. Recommended Response Action Refer to the Lifecycle Controller - Remote Services User Guide and retry the operation with the appropriate value.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0302 Message iDRAC Express does not support this feature. Detailed Description This error message is displayed when iDRAC does not have a valid Enterprise license. Recommended Response Action Upgrade to iDRAC Enterprise for supporting this feature. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0304 Message Firmware update is terminated. Detailed Description Firmware update is terminated. Recommended Response Action No response action is required. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC032 Message Invalid value specified for DNS RAC name. Detailed Description The DNS RAC name specified is not valid. Recommended Response Action Retry operation with valid DNS RAC name.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC034 Message Unable to create a job because the job queue is full. Detailed Description The job queue is full. Recommended Response Action Wait for existing jobs to run to completion or delete some jobs from the job queue.
Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC036 Message Attribute dependency failed. Detailed Description The value of the specified attribute is dependent on the value of another attribute. The current value dependency is invalid.
Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0400 Message iDRAC memory low. Detailed Description iDRAC is running low on memory. Recommended Response Action No response action is required.
Detailed Description Critical error from iDRAC service recovery program. Recommended Response Action No response action is required Category Audit Subcategory RAC = RAC Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log;None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC049 Message Resource allocation failure.
RAC050 Message Invalid country code. Detailed Description The country code is not entered in the correct format or does not exist. Refer to ISO 3166 for the correct country code format. Recommended Response Action Enter country code in the correct format as defined in ISO 3166. For example, United States = US. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0501 Message There are no physical disks to be displayed. Detailed Description Physical disks cannot be displayed. This error may occur if the host system is powered off or the physical disks are removed. This may result in communication loss while retrieving controller data. Recommended Response Action 1. Check if the host system is powered off or shutdown. 2. Check if the physical disks are inserted into the enclosure or attached to the backplane. 3.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0503 Message There are no out-of-band capable controllers to be displayed. Detailed Description Out-of-band controllers cannot be displayed. This error may occur if the host system is powered off, or controllers are removed or disconnected. Recommended Response Action Check if the host system is powered off or shutdown.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0505 Message There are no devices to be displayed. Detailed Description Devices are not displayed. This error may occur because these components are removed or disconnected. Recommended Response Action 1. Check if the host system is ON. 2. Check if the Storage Enclosure is ON. 3. Verify that the adapter cables are properly connected and there are no bent pins.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0507 Message Unable to find the requested resource. Detailed Description The requested information cannot be displayed, because the system did not find any matching resource. This occurs because the system is turned off, resource is not present, or the resource is removed or deleted.
Subcategory RAC = RAC Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0509 Message The server is temporarily unavailable. Try again after sometime Detailed Description The server is currently unable to handle the request due to temporary overloading or server maintenance. Recommended Response Action Wait for few minutes and refresh the page.
Recommended Response Action Remove the unsupported parameter and retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0510 Message There are no events to be displayed. Detailed Description This error occurs if Lifecycle log events have not occurred recently.
Detailed Description Physical disks cannot be displayed. This error may occur if the host system is powered off, physical disks are removed, or incorrect filters are applied. Recommended Response Action 1. Check if the host system is powered off or shutdown. 2. Check if the physical disks are inserted into the enclosure or attached to the backplane. 3. Check if correct filters are applied. 4. Check that the Storage Enclosure is on. 5.
RAC0513 Message There are no virtual disks to be displayed. Detailed Description There are no virtual disks to be displayed. There may be no virtual disks created, the controller(s) may not be in RAID mode, or there may be pending creation or deletion jobs that have not completed. Recommended Response Action Check the following: 1) Check if the server is turned off. If the server is turned off, turn it on and wait until POST completes.
RAID mode, convert them to RAID mode by pressing Ctrl+R while restarting the server, and then select the required controller. Press F2 and select the Convert to RAID capable option, and then complete the operation. 5) If a job is currently running or scheduled on the selected controller, the job must be completed or deleted before attempting a new operation. Status of the scheduled job can be viewed and managed on the Job Queue page on iDRAC. Click Job Queue link to view the status of the scheduled jobs.
RAC053 Message OS to iDRAC pass-through is disabled. Detailed Description One or more attributes being set are dependent on OS to iDRAC pass-through being enabled. Recommended Response Action Enable OS to iDRAC pass-through and retry the previous command. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC055 Message User name cannot be cleared because the user account is enabled in the input configuration XML file. Detailed Description The user name for the user account cannot be cleared because the user account is enabled in the configuration XML file. Recommended Response Action Retry the operation after disabling the user account in the configuration XML file.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0560 Message RAC Software Initialization Error Detailed Description RAC Software Initialization error.
line utility and entering "racadm racreset". 3) After the iDRAC has restarted, if the communications link is still not functioning, restart the CMC and check the Lifecycle Log for this link error after the CMC has restarted. 4) If the issue persists, contact your service provider. Category System Health Subcategory RAC = RAC Event Severity Severity 3 (Informational) Trap/EventID 2531 LCD Message No LCD message display defined.
RAC057 Message Arguments Unable to set Privacy Protocol to an enabled state because the Authentication Protocol attribute is set to None for the user ID: arg1 • arg1 = user ID Detailed Description The Privacy Protocol for the user cannot be enabled because the Authentication protocol is disabled. Recommended Response Action Enable the Authentication Protocol attribute for the identified user ID account, and retry the operation to set the Privacy Protocol to an enabled state.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC059 Message Unable to configure iDRAC time because Network Time Protocol (NTP) is enabled. Detailed Description When the Network Time Protocol (NTP) feature is enabled, the iDRAC will get time from the configured NTP server. Directly configuration of the iDRAC time is disabled when NTP is enabled. Recommended Response Action Disable Network Time Protocol (NTP) and retry the operation.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0600 Message Unable to retrieve the temperature information. Detailed Description Temperature information cannot be displayed. This error may occur if the server is powered off. Recommended Response Action Power on the server.
Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0602 Message Invalid value for alert recurrence. Detailed Description The value for alert recurrence must be within the range 0-365. Recommended Response Action Enter a value between 0-365.
Recommended Response Action Click Job Queue button to view the status of the update jobs. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0604 Message System inventory may not be up-to-date because Collect System Inventory On Restart (CSIOR) is disabled.
RAC0605 Message There are no jobs to be displayed. Detailed Description There are no jobs to be displayed. Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0606 Message The network connection test operation was successful.
Server Administrator Trap ID Not Applicable RAC0607 Message Unable to perform OS to iDRAC Pass-Through with the current system configuration. Detailed Description The integrated NICs in the system do not support OS to iDRAC Pass-Through. Recommended Response Action Make sure the integrated NICs are enabled from BIOS setup and support OS to iDRAC Pass-Through, then retry the operation. To access BIOS setup, press F2 during system startup.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0609 Message Arguments The job arg1 has been successfully added to the job queue. • arg1 = import or export job ID Detailed Description The import or export system configuration operation with the job ID indicated in the message was successfully added to the Job Queue. Recommended Response Action No response action is required. The status of jobs can be viewed on the Job Queue page.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0610 Message The passphrase and confirm passphrase values entered do not match. Detailed Description Different values were entered for passpharse and confirm passpharse field. Recommended Response Action Values entered in passphrase and confirm passphrase fields must be the same.
Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0612 Message Cancelling the firmware update operation will delete all the uploaded firmware files. Do you want to continue? Detailed Description Cancelling the firmware update operation will cancel all firmware updates selected and delete all uploaded firmware files.
Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0614 Message Incorrect password for PKCS#12 file. Detailed Description The specified password was incorrect for the PKCS#12 file. Recommended Response Action Make sure to use the correct password for the PKCS#12 file.
Recommended Response Action Make sure to upload the file in PKCS#12 format. OpenSSL can be used to validate a PKCS#12 file. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0616 Message Error while extracting custom signing certificate and private key from the PKCS#12 file.
Detailed Description An error occurred while generating new iDRAC SSL Certificate or signing it with new custom signing certificate. Recommended Response Action Make sure to upload an PKCS#12 file that contains a valid custom signing certificate and private key, then retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
RAC0619 Message The iDRAC firmware rollback will cause an iDRAC restart and all current user sessions will be closed. Detailed Description The message appears in Firmware Rollback page when the iDRAC firmware rollback action completed successfully. Recommended Response Action Reconnect iDRAC communications sessions after iDRAC is restarted. The iDRAC will be ready for login once the restart is complete.
Server Administrator Trap ID Not Applicable RAC0620 Message Lifecycle Controller is unable to delete the selected jobs. Detailed Description Lifecycle Controller is currently busy performing tasks. The selected jobs cannot be deleted until the following: 1) The Lifecycle Controller tasks are completed. 2) The system completes all the Power-on-Self-test (POST) operations.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0622 Message An invalid certificate file is uploaded. Detailed Description The certificate file is invalid for one of the following reasons: 1) CA Certificate is corrupted, expired, or does not have signing privileges. 2) CA private key does not matchi with CA Certificate being uploaded. Recommended Response Action Make sure the CA certificate and private key are correct and retry the operation.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC064 Message iDRAC was successfully reset. Detailed Description iDRAC was successfully reset. Recommended Response Action No response action is required.
Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0654 Message No operations can be performed on the iDRAC Service Module. Detailed Description Unable to perform operations on the iDRAC Service Module (iSM) because the iSM is not installed on the server operating system.
Detailed Description The Replicate Lifecycle Controller Log in OS Log and Auto System Recovery Action features are disabled in the iDRAC Service Module because the OpenManage Server Administrator is installed on the server operating system. Recommended Response Action None Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC0657 Message The file name field must not be blank. Detailed Description The file name cannot be blank when performing the Backup Server Profile operation. Recommended Response Action Enter an appropriate file name, and then retry the operation. Category Audit Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC067 Message iDRAC reset to factory defaults operation was not successful. Detailed Description iDRAC reset to factory defaults operation was not successful. This may be due to IPMI communications issues. Recommended Response Action Do the following: 1) Retry the operation. 2) If the issue persists, remove AC input power from the server and re-apply AC power to the server and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC069 Message String Less than Min Supported Length Detailed Description String Less than Min Supported Length Recommended Response Action None Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0700 Message Arguments Email page successful to arg1 . • arg1 = email address Detailed Description An email page was successfully sent. Recommended Response Action No response action is required. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0702 Message Requested system powercycle. Detailed Description Requested system powercycle. Recommended Response Action No response action is required. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0704 Message Requested system powerdown. Detailed Description Requested system powerdown. Recommended Response Action No response action is required.
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0706 Message Requested system NMI. Detailed Description Requested system NMI. Recommended Response Action No response action is required.
Recommended Response Action Acquire an iDRAC firmware image of the version desired. Using the latest version available is recommended. Update the iDRAC firmware. Category Updates Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0708 Message Previous reboot was due to a firmware watchdog timeout.
Detailed Description Unknown server inserted into chassis. Recommended Response Action Acquire the latest Chassis Management Controller (CMC) firmware that supports the server indicated and update the CMC to at least that version. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC0710 Message Server link tuning error. Detailed Description Server link tuning error. Recommended Response Action Ensure that the IO Module (IOM) and Mezzanine (Mezz) cards are appropriately matched. Check the M1000e Hardware Manual for correct component compatibility. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0712 Message Server failed to power up due to zero power allocated. Detailed Description Server failed to power up due to zero power allocated. Recommended Response Action Utilize the Chassis Management Controller web interface to check available power and server power requirements. If sufficient power is available, allocate power necessary and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0714 Message Server failed to power up due to noncontinuous power action. Detailed Description Server failed to power up due to noncontinuous power action. Recommended Response Action Utilize the Chassis Management Controller web interface to check available power and server power requirements. If sufficient power is available, allocate power necessary and retry the operation.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0716 Message Unable to unmount remote share. Detailed Description Unable to unmount remote share. Recommended Response Action Retry the operation. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0718 Message Remote File Share service is busy with the previous connection. Detailed Description Remote File Share service is busy with the previous connection. Recommended Response Action Stop the Remote File Share session and retyr the operation.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC072 Message Unable to perform the iDRAC reset to factory defaults operation because the firmware upgrade is in progress. Detailed Description The iDRAC reset to factory defaults operation cannot be completed because a firmware upgrade operation is in progress.
Recommended Response Action Retry the operation. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0721 Message Arguments Remote share mounted successfully arg1 . • arg1 = sharename Detailed Description Remote share mounted successfully. Recommended Response Action No response action is required.
RAC0722 Message Arguments Failed to program the Chassis assigned MAC address for the NIC.Integrated. arg1 . • arg1 = NDC slot number Detailed Description Failed to program the Chassis assigned MAC address for the NIC.Integrated in the specified slot number. Recommended Response Action Reseat the server and retry. Category Audit Subcategory RAC = RAC Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default SNMP Alert;OS Log;LC Log;Remote System Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0724 Message Quick Sync Firmware is successfully updated. Detailed Description Quick Sync Firmware is successfully updated. Recommended Response Action No response action is required. Category Updates Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0726 Message Auto-throttling is disabled for the server. Detailed Description Auto-throttling is disabled for the server based on a request from the Chassis Management Controller (CMC) because the CMC is restarting.. Recommended Response Action No response action is required.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0728 Message The Quick Sync communication is no longer functioning. Detailed Description The Quick Sync communication or the connection to the iDRAC is no longer functioning. Recommended Response Action Do the following: 1) Remove and reseat the bezel.
Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC074 Message Unable to perform the iDRAC reset to factory defaults operation because a vFlash partition creation operation is in progress.
Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0901 Message Invalid syntax. The -t option value must set to 1. Detailed Description The syntax of the specified command is invalid. In this case, the usage of the -t option is invalid.
Recommended Response Action See the help text/documentation for the valid syntax of the subcommand. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0903 Message The -d option cannot be used with any other options. Detailed Description The syntax of the specified command is invalid.
Detailed Description The iDRAC cannot access the remote file location. The credentials or path to the remote file location is incorrect or iDRAC cannot connect to the network address. Recommended Response Action Confirm that the path and credentials to remote file are correct, and check that the iDRAC can connect to the network address. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
RAC0906 Message Operation failed. Detailed Description Unable to perform the requested operation. Recommended Response Action Try again later. If the problem persists, contact technical support. Refer to your product documentation to choose the contact method. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC0908 Message System ID LED blink off. Detailed Description The System ID LED was successfully set to off. Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0910 Message Invalid subcommand syntax: Specify group and object name. Detailed Description The specified command is missing group and object name syntax. Recommended Response Action Specify the correct subcommand group and object name syntax. See the help text or documentation for the valid syntax.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC0912 Message Unable to connect to RAC at specified IP address. Detailed Description The management system could not connect to the iDRAC. Recommended Response Action Verfiy whether the IP address of the remote iDRAC is correct. Verify whether connectivity exists between the management system and the iDRAC.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1001 Message Unable to set the object value for iDRAC IPv6 DNS1 or DNS2. Detailed Description Unable to set the object value for iDRAC IPv6 DNS1 or DNS2, because the object DNSFromDHCP6 is enabled. Recommended Response Action Disable the object DNSFromDHCP6 using "racadm set iDRAC.IPv6.DNSFromDHCP6 <0 | Disabled>", and retry the operation.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1003 Message The smart card certificate revocation list (CRL) cannot be enabled. Detailed Description The smart card certificate revocation list (CRL) cannot be enabled, because the object SmartCardLogonEnable is disabled.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1005 Message Successfully exported hardware inventory. Detailed Description The hardware inventory was successfully exported.
Recommended Response Action Do one of the following and retry the operation: 1) Dowload the correct Update Package from your service provider. 2) Use the Lifecycle Controller repair package to repair Lifecycle Controller. For more information, see Lifecycle Controller Users Guide. 3) Wait until the current update operation is complete. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
RAC1008 Message The Active Directory object DCLookupByUserDomain cannot be disabled. Detailed Description The Active Directory object DCLookupByUserDomain cannot be disabled, because the Active Directory object DCLookupDomainName is not configured. Recommended Response Action Configure the Active Directory object DCLookupDomainName using "racadm set iDRAC.ActiveDirectory.DCLookupDomainName ", and retry the operation.
Server Administrator Trap ID Not Applicable RAC1010 Message Unable to set the power cap value. Detailed Description The power cap cannot be set if the object Power.Cap is disabled. Recommended Response Action Enable Power Cap setting using "racadm set System.Power.Cap.Enable < 1 | Enabled >", and retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1012 Message Unable to change the auto-negotiation state for the current NIC selection mode. Detailed Description Unable to change the auto-negotiation state for the current NIC selection mode, because the iDRAC NIC is in dedicated mode. Recommended Response Action Change the iDRAC NIC mode to shared mode using "racadm set idrac.nic.selection ", and retry the operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1014 Message The SNMPv3 privacy protocol cannot be configured to AES or DES mode if SNMPv3 authentication protocol state is set to "None". Detailed Description The SNMPv3 privacy protocol cannot be configured to AES or DES mode if SNMPv3 authentication protocol state is set to "None".
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1017 Message Successfully modified the object value and the change is in pending state. Detailed Description Any staged operation requires a job and system reboot to apply the object values. Recommended Response Action To apply modified value, create a configuration job and reboot the system.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1019 Message The specified object is not supported for the current system configuration. Detailed Description Some objects have dependencies on other objects that are required to perform a task. The specified object is not available because of such dependencies.
Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1021 Message NIC objects are not available in the current system configuration. Detailed Description NIC objects are not available if NIC devices are not installed in the system, or if some iDRAC services are busy.
Recommended Response Action Make sure that there is at least one object on the specified device or component that has a pending vlaue, and retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1024 Message Successfully scheduled a job.
Detailed Description Some objects have dependencies on other objects that are required to perform a task. However, some of the objects are read-only because of the current system configuration and the values of the dependent objects. Recommended Response Action Verify the object dependency using "racadm help ..", and retry the opearation.
RAC1027 Message Successfully sent the alert for the specified event to the configured destination. Detailed Description A test event was generated and the alert was successfully sent to the destination. Recommended Response Action Verify if the alerts were received by the configured tdestination. Otherwise, reconfigure the destination and retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC1029 Message Unable to delete the specified certificate type. Detailed Description The certificate cannot be deleted if the certificate type specified is not "3". Recommended Response Action Make sure to specify "3" for the certificate type (-t) option, and retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1031 Message Unable to delete the custom signing certificate. Detailed Description The custom signing certificate on iDRAC cannot be deleted because of an internal error. Recommended Response Action Verify if iDRAC has a custom signing certificate. If it has the certificate, retry the operation. If the issue persists, contact your service provider.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1033 Message Unable to retrieve the server component software inventory. Detailed Description The server component software inventory cannot be retrieved because of an internal error. Recommended Response Action Make sure to enable Collect System Inventory On Restart (CSIOR) feature, reboot the server, and retry the operation.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1035 Message There are no pending values to be cleared. Detailed Description The command is unable to clear the pending state for attributes of the specified component because there are no pending values.
Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1037 Message Unable to clear pending attribute(s). Detailed Description Unable to clear pending attribute(s). This may be because the FQDD entered is incorrect. Recommended Response Action Check that the FQDD entered is correct.
Recommended Response Action Make sure that a config job is not scheduled for this component. For more information, view the help command by running the RACADM command "racadm jobqueue help delete". Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description The requested RAID storage operation was successfully accepted and now must be applied by creating a RAID storage configuration job. Recommended Response Action To apply the configuration operation, create a configuration job, and then restart the server. To create the required commit and reboot jobs, run the jobqueue command. For more information about the jobqueue command, enter the RACADM command "racadm help jobqueue".
RAC1042 Message Unable to configure the Automatic Update (autoupdate) feature settings. The required options are either invalid or not provided. Detailed Description One or more required options to configure the Automatic Update (autoupdate) feature are missing. Recommended Response Action For more information, view the help details by running the RACADM command "racadm help autoupdatescheduler".
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1044 Message The Automatic Update (autoupdate) feature is not enabled. Detailed Description The Automatic Update (autoupdate) feature is not enabled Recommended Response Action To enable, run the RACADM command "racadm set lifecyclecontroller.lcattributes.autoupdate 1". Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1046 Message Unable to view the Automatic Update (autoupdate) feature settings because the feature has not been configured. Detailed Description Unable to view the Automatic Update (autoupdate) feature settings because the feature has not been configured.
Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1048 Message Unable to clear the Automatic Update (autoupdate) feature settings because there is currently no configuration. Detailed Description The Automatic Update (autoupdate) feature settings must already exist in order to be cleared.
Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1050 Message Unable to configure the Automatic Backup (autobackup) feature settings. The required options are either invalid or not provided.
Detailed Description The operation did not complete successfully because of an invalid value for the option identified in the message. Recommended Response Action Retry with a correct value for the option identified in the message. For more information, view the help details by running the RACADM command "racadm help systemconfig backup". Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC1053 Message Unable to view the Automatic Backup (autobackup) feature settings because the feature has not been configured. Detailed Description Unable to view the Automatic Backup (autobackup) feature settings because the feature has not been configured. Recommended Response Action Configure the Automatic Backup feature by running the RACADM command "racadm systemconfig backup" with the desired option settings.
Server Administrator Trap ID Not Applicable RAC1055 Message Unable to clear the Automatic Backup (autobackup) feature settings because there is currently no configuration. Detailed Description The Automatic Backup (autobackup) feature settings must already exist in order to be cleared. Recommended Response Action No response action is required Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1057 Message Rollback operation did not complete successfully. The component identifier specified is not valid or does not have a rollback firmware image available. Detailed Description Rollback operation did not complete successfully. The component identifier (FQDD) specified in the operation is not valid or does not have a Rollback firmware image available.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1059 Message Rollback operation could not be performed because another firmware update job is running. Detailed Description The requested firmware rollback operation could not be performed because another firmware update job is running or being scheduled.
Recommended Response Action To enable the CSIOR feature, run the RACADM command "racadm set LifecycleController.LCAttributes.CollectSystemInventoryOnRestart 1". Then restart the server to cause system inventory information to be collected. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description Unable to initiate the requested SystemErase operation. The component identifier specified is not valid. Recommended Response Action Run the RACADM command "racadm help systemerase" to see the list of supported components. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
RAC1064 Message Unable to initiate the SystemErase operation because another instance of SystemErase job is already in progress. Detailed Description Unable to initiate the requested SystemErase operation because another SystemErase job is already in progress. Recommended Response Action To check the job status, run the RACADM command "racadm jobqueue view" and retry the operation after the current SystemErase operation has completed.
Server Administrator Trap ID Not Applicable RAC1067 Message Arguments Unable to set the minimum non critical threshold value of arg1 , because the value entered is lesser than, or equal to the minimum critical threshold value. • arg1 = System Board Inlet Temp Detailed Description The minimum non critical threshold value identified in the message cannot be set, because the value entered is lesser than, or equal to the minimum critical threshold value.
Recommended Response Action Check the maximum non critical threshold level using an appropriate RACADM command. For example, to view the maximum non critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC1070 Message Arguments Unable to set the maximum non critical threshold value of arg1 , because the value entered is greater than, or equal to the maximum critical threshold value. • arg1 = System Board Inlet Temp Detailed Description The maximum non critical threshold value identified in the message cannot be set, because the value entered is greater than or equal to the maximum critical threshold value.
Recommended Response Action Check the minimum non critical threshold level using an appropriate RACADM command. For example, to view the minimum non critical threshold value of a sensor, run the racadm getsensorinfo command at the command line interface, and then retry the operation. For more information about other RACADM commands, run the racadm help command. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC1073 Message Arguments Unable to reset the threshold value of sensor arg1 because the capability to reset this sensor threshold value is not supported. • arg1 = sensor name Detailed Description The threshold value of the sensor identified in the message cannot be successfully set because the capability reset the sensor threshold value is not supported. Recommended Response Action No response action is required.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1110 Message Unable to run the command, because an incorrect Proxy port number was entered. Detailed Description Unable to run the command, because an incorrect Proxy port number was entered. The Proxy port value must be a positive integer. Recommended Response Action Enter only numbers for a Proxy port value.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1112 Message Unable to delete the pending values for the specified device because the iDRAC internal storage is in use by a currently running job. Detailed Description Unable to clear the pending state from the attributes for a RAID object. A job is currently running and iDRAC internal storage is in use.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1114 Message Arguments Configuration XML file preview operation job is initiated. Job ID = arg1 • arg1 = job ID Detailed Description The configuration XML preview operation was successfully initiatied and has generated a job with the job ID identified in the message.
Recommended Response Action Make sure that you have appropriate privileges, and then retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1116 Message Unable to run the command, because the restart flag entered is incorrect.
Detailed Description The operation specified in the command could not be successfully completed. Recommended Response Action Retry the operation after 2 minutes. If the problem persists, contact your service provider. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC1119 Message Unable to generate a comparison report for the specified repository. Detailed Description The command could not be successfully run because of one or more of the following reasons: 1. The command does not have "--verifycatalog" in it. 2. The updates available on the repository are not applicable for the operation that is requested. Recommended Response Action To generate a comparison report, type "--verifycatalog" in the racadm command, and then retry the operation.
Server Administrator Trap ID Not Applicable RAC1121 Message Unable to run the command, because the data entered for connecting to the Proxy server is insufficient. Detailed Description The command could not be successfully run, because one or more values about the proxy server was not entered.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1123 Message Unable to perform the operation because Fibre Channel (FC) attributes are not available in the current server configuration. Detailed Description Fibre Channel (FC) objects are not available if Fibre Channel devices are not installed in the server, or if some iDRAC services are busy. Recommended Response Action Do the following: 1) Power off and remove AC or DC power from the server.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1129 Message Unable to modify the BootOnce object. Detailed Description The BootOnce object could not be modified, because the FirstBootDevice object is set to either F10, F11, or BIOS.
Recommended Response Action Verify whether or not a correct version of BIOS, Lifecycle Controller, and/or iDRAC firmware is installed. For more information on the appropriate firmware version required, refer to the RACADM Command Line Reference Guide. Also check if there is a limitation in terms of platforms such as monolithic or modular, and then retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Detailed Description The firmware could not be successfully updated, because one or all of the following values are incorrect: a. logon ID b. IP address of TFTP or FTP server c. Full path of the firmware file. Recommended Response Action Run the racadm command "racadm help " to get more details about the various options applicable for this command and the values accepted by the command.
RAC1134 Message Unable to export the Lifecycle log data, because the export file size larger than 25MB and cannot be processed locally. Detailed Description Unable to export the Lifecycle log data, because the export file size larger than 25MB and cannot be processed locally. Recommended Response Action Export the Lifiecycle Log to a network file share.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1136 Message Remote unattended diagnostic execution operation initiated. Detailed Description The remote unattended diagnostic execution operation is initiated. Recommended Response Action Using the RACADM command line interface, run the "racadm jobqueue view -i " command to view the status of the operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1138 Message Unable to export the diagnostics results because the results do not exist. Detailed Description Unable to export the remote diagnostics results because the remote diagnostics results have not been generated.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1140 Message File name is not required to export the Technical Support Report (TSR) to a remote share. Detailed Description The file name cannot be specified when the Technical Support Report (TSR) is exported to a remote share. Recommended Response Action Run the command without using the -f option.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1142 Message Unable to start the Remote Diagnostics operation because the Expiration Time entered (difference between Start Time and Expiration Time) is less than five minutes.
Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1144 Message Arguments The Job: arg1 is invalid or is not present in the job queue and a related Lifecycle Log entry is not found.
RAC1145 Message The entered log type is invalid. Detailed Description The value entered for the -t option is invalid. Recommended Response Action Check help text for the list of valid log types and retry the operation by entering a valid log type. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC1147 Message Unable to set the SNMPv3 username entered in the command because the username is not present or enabled on iDRAC. Detailed Description The SNMPv3 user cannot be set because the user with the entered username for the SNMPv3 group is not present or enabled on iDRAC. Recommended Response Action Make sure the specified username is present on iDRAC and enabled, and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1151 Message The export operation is unsuccessful. Detailed Description The export operation did not complete successfully. Recommended Response Action Run the RACADM techsupreport collect command again and then retry the export operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1153 Message The time stamp is not available to display. Detailed Description The time stamp was not recorded for the previous techsupreport collect operation. Recommended Response Action Run the RACADM techsupreport collect command. After the techsupreport collect operation completes, run the RACADM getupdatetime command.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1155 Message Unable to complete the operation because Lifecycle Controller is disabled. Detailed Description The operation was not completed because Lifecycle Controller is disabled. Recommended Response Action Enable the Lifecycle Controller and retry the operation.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1157 Message Unable to find the specified FQDD. Detailed Description The specified FQDD is invalid. Recommended Response Action Verify whether or not the entered FQDD is valid. Run the command racadm gethostnetworkinterfaces for the list of valid FQDDs.
Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1159 Message Unable to get the requested data from iDRAC. Detailed Description The data cannot be retrieved from iDRAC because Lifecycle Controller is disabled or a DUP update is in progress.
Detailed Description Unable to set USB group objects because the user account identified in the message does not have the System Control privilege, which is required for this operation. Recommended Response Action Contact the iDRAC system administrator and get the System Control privilege added to the account identified in the message or use account credentials that have System Control privilege and retry the operation.
RAC1162 Message Unable to initiate the techsupreport collect operation for the Tech Support Report (TSR) because another collect operation is in progress. Detailed Description The requested techsupreport collect operation cannot be initiated because another techsupreport collect operation for the Tech Support Report (TSR) is in progress. Recommended Response Action Wait for the current collect operation to complete before initiating another collect operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1164 Message A remote diagnostics operation is currently running and not completed. Detailed Description A remote diagnostics operation is already under execution and another operation can be started only after the current execution is completed. Recommended Response Action Initiate another diagnostics operation only after the currently running operation is completed.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1166 Message Arguments Successfully initiated Configuration XML file preview operation that was invoked by arg1 . • arg1 = user name Detailed Description The Configuration XML file preview operation was successfully initiated after it was invoked by the user name identfied in the message. Recommended Response Action No response action is required.
Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1169 Message The RACADM "config" command will be deprecated in a future version of iDRAC firmware. Detailed Description The RACADM "config" command will be deprecated in a future version of iDRAC firmware.
Recommended Response Action If a SSL library is not installed, install one and retry the operation. If a SSL library is installed, create a soft-link of the installed SSL library to "libssl.so" using the linux "ln" command and retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description The Certificate Signing Request (CSR) message cannot be generated because all the attributes in the iDRAC.Security group are not configured. Recommended Response Action Make sure that all the attributes in the iDRAC.Security group are configured. To get the list of attributes, run the following command "racadm get iDRAC.Security". Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC1178 Message A USB device is attached to the iDRAC and a configuration XML import operation is in progress. Detailed Description A USB device is attached to the iDRAC and a configuration XML import operation is in progress. Recommended Response Action Wait until the configuration XML import operation has completed before attempting another operation. Verify the status of the configuration XML import operation by running the RACADM command "racadm jobqueue view".
Server Administrator Trap ID Not Applicable RAC1180 Message A USB device is inserted in the front panel USB Management port and is in use by the server operating system. Detailed Description A USB Device inserted in the front panel USB Management port and is in use by the server operating system. The device needs to not be in use in order to change the port mode settings. Recommended Response Action Remove and reinsert the USB device and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1182 Message Unable to retrieve information for the Power group or attribute because the server is not PMBus capable. Detailed Description The server instrumentation can not provide any information related to power because PMBus capability is not present or the PSU(s) with PMBus capability have been removed. Recommended Response Action No response action is required.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1184 Message The getuscvresion RACADM subcommand will be deprecated in a future release. Detailed Description The getuscvresion RACADM subcommand will be deprecated in a future release. Recommended Response Action Instead of getuscversion, run the getversion -f lc subcommand.
Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC1186 Message 1000Mbps speed setting is Read Only and cannot be configured for the iDRAC NIC. Detailed Description Only possible configurations for the DRAC NIC are 10Mbps and 100 Mbps.
Recommended Response Action No response action is required. Category Audit Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC913 Message Unable to login to RAC using the specified address Detailed Description The management system could not login to the iDRAC.
Detailed Description The specified value is not within the valid range. To set the LED state to off, enter 0. To set the LED state to on, enter 1. Recommended Response Action Set the numeric value to 0 (Off) or 1 (On). Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
RAC916 Message Value given exceeds the maximum threshold value. Detailed Description The value given is greater than the maximum threshold value. Recommended Response Action Set values lesser than the maximum threshold value. To view the maximum threshold value, run racadm get System.Power. Cap.MaxThreshold at the command prompt. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC918 Message Unable to get the inlet temperature data. Detailed Description Racadm unable to obtain the inlet temperature data. This happens if there is no data populated in the temperature tables or if the underlying instrumentation does not return valid values. Recommended Response Action Wait for the underlying instrumentation to populate the thermal tables. Retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC920 Message This interface does not support the specified option. Detailed Description From firmware racadm, the inlet temperature history can be exported only to a remote file share. Recommended Response Action Create a remote file share to export the inlet temperature history. Else, use remote/ local racadm to export to the file system accessible by the racadm executable.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC922 Message Specified path is too long. Detailed Description The specified path (specified with the l parameter) for the remote share is too long. This path should be less than 256 characters in length. Recommended Response Action Try the same command with a different remote share location, which is less than 256 characters in length.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC924 Message Inlet temperature history exported successfully. Detailed Description The inlet temperature history was successfully exported to the specified file. Recommended Response Action None. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC926 Message The recurrence interval needs to be an integer from 0 to 365. Detailed Description The value given for the recurrence interval is invalid. It has to be a value from 0 to 365. Recommended Response Action Change the argument of r to a value from 0 to 365 and then run the same command.
Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC928 Message Unable to modify the recurrence value. Detailed Description Racadm unable to set the recurrence value. This occurs if the underlying instrumentation do not set the value. Recommended Response Action Wait for a few minutes and retry the command.
Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC930 Message Unable to export the inlet temperature data. Detailed Description Racadm is currently unable to obtain the inlet temperature data.
Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC937 Message Arguments Successfully initiated configuration XML file import operation that was invoked by the arg1 .
RAC938 Message Arguments Successfully initiated configuration XML file export operation invoked by the arg1 . • arg1 = user name Detailed Description The configuration XML file export operation was successfully initiated after it was invoked by the user specified in the message. Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC940 Message Unable to start the system configuration profile export or import operation. Detailed Description If an existing system profile import or export job is running, then a system configuration profile backup or restore opeartion cannot be started. Recommended Response Action Wait until the existing system profile export or import job is completed or cancel the job before retrying the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC942 Message Successfully initiated the import operation. This operation may take several minutes to complete and may cause multiple system restarts while device firmware and configuration are applied. Detailed Description The system configuration profile import operation is initiated.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC944 Message Unable to create the configuration job. Detailed Description A configuration job cannot be created if Lifecycle Controller is disabled. Recommended Response Action Run "racadm set LifecycleController.LCAttributes.LifecycleControllerState 1" to enable Lifecycle Controller, and retry the operation.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC946 Message Unable to set the NIC to Auto Dedicated NIC mode. Detailed Description The "Auto Dedicated NIC" mode cannot be set for a NIC if the NIC selection mode is set to "Dedicated NIC".
Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC948 Message Unable to send the notification for the specified event to the configured destination. Detailed Description A test event notification for the specified message ID was not sent to the configured destination.
Recommended Response Action View the work notes using the racadm lclog view c worknotes command. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC950 Message Unable to add the work note to the Lifecycle Log.
Detailed Description Up to 256 characters are allowed for a work note. Recommended Response Action Do not exceed 256 characters in the work note, and retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC952 Message There is no free space to add new work notes to the Lifecycle Log.
RAC953 Message Successfully added the comment. Detailed Description The comment was added to the specified entry in the Lifecycle Log. Recommended Response Action View the added comment using the racadm lclog view q -n 1 command. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC955 Message Unable to retrieve the information related to the specified record in the Lifecycle Log. Detailed Description The specified record does not exist in the Lifecycle Log. Recommended Response Action Run the racadm lclog view -i command to get the sequence number of the records logged in the Lifeycle Log, and retry the command with a valid sequence number.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC957 Message An import or export operation is currently in progress. Detailed Description Another import or export operation cannot be started until the current operation is complete. Recommended Response Action Wait until the current import or export operation is complete before starting another operation. Use the racadm jobqueue view command to check the status of the current import or export operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC959 Message Invalid file used for configuration XML file import operation. Detailed Description The content of the configuration XML file used for import is invalid because of incorrect modifications or content. Recommended Response Action Correct the modifications to the configuration XML file to be imported or specify the correct file, and retry the operation.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC961 Message A pending or committed system configuration change exists. Detailed Description Another import operation cannot be started if an import operation that was performed earlier has some pending or commited configuration changes.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC963 Message Unable to retrieve the status of Lifecycle Controller. Detailed Description iDRAC is unable to read Lifecycle Controller status. Lifecycle Controller must be enabled to run the operation. Recommended Response Action Run the racadm get LifeCycleController.LCAttributes.
Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC965 Message The -l option must be specified if -u and -p are used. Detailed Description Any operation involving remote share (CIFS) cannot continue if the location (-l) is not specified.
Recommended Response Action Make sure to specify both user name and password for the remote share, and retry the operation. To view the list of options that can used for the required subcommand, use the racadm help command. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Detailed Description The configuration XML file cannot be imported from a client location when using Firmware RACADM. Recommended Response Action When using Firmware RACADM, make sure to import the configuration XML file from a remote share only. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RAC970 Message Incorrect value specified for the end power state option. Detailed Description The import operation cannot continue if the value specified for the end power state of the system option (-s) is incorrect. The supported values are "On" and "Off". Recommended Response Action Make sure to specify either "On" or "Off" for the end power state (-s) option. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC972 Message Insufficient privileges to run the configuration XML file import or export operations. Detailed Description Configuration XML import and export operations require the specified username to have administrator role privileges. Recommended Response Action Run the same command with a username that has an administrator role privileges.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC974 Message Invalid wait time specified. Detailed Description The value specified for the wait time (w) option is invalid. The valid range is 300 to 3600 seconds. Recommended Response Action Make sure to specify a valid wait time (-w) option and retry the command. The range of supported values are 300 to 3600 seconds.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC976 Message Export configuration XML file operation initiated. Detailed Description The configuration XML file export operation was initiated. Recommended Response Action Use the racadm jobqueue view i command to view the status of the operation.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC978 Message Unsupported Lifecycle Controller firmware version detected. Detailed Description The Lifecycle Controller firmware version on the target system does not support the configuration XML file import or export operations. Recommended Response Action Update to the latest Lifecycle Controller firmware and retry the operation.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC981 Message The type of certificate specified does not require a passphrase. Detailed Description A passphrase is required only for passphrase protected certificate, which is specified using the value of 3 for the -t option.
Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC983 Message Invalid passphrase provided for the Public Key Cryptography Standards version 12 (PKCS12) file. Detailed Description The Public Key Cryptography Standards version 12 (PKCS12) file is passphrase protected, and the passphrase provided is invalid.
Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC985 Message Unable to configure the cfgServerBootOnce object. Detailed Description The object "cfgServerBootOnce" cannot be configured if the object "cfgServerFirstBootDevice" is set to F10, F11, or BIOS value.
Recommended Response Action Use "vflashsd" sub-command instead of "vmkey". For more information about the sub-command, use "racadm help vflashsd" command. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC987 Message Arguments Firmware update job for arg1 is initiated.
RAC988 Message Arguments Unable to initiate the arg1 firmware update. • arg1 = file name Detailed Description A new firmware update job cannot be initiated while an existing firmware update job is still in one of these states: "New", "Downloading", or "Running". Recommended Response Action Wait until the existing firmware update jobs are completed or scheduled before retrying the operation. To monitor the status of the existing jobs, use the "racadm jobqueue view" command.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC990 Message Arguments Unable to apply the arg1 update. • arg1 = file name Detailed Description If Lifecycle Controller is disabled, the firmware update operation cannot continue. Recommended Response Action Enable Lifecycle Controller using the "racadm set lifecyclecontroller.lcattributes.lifecyclecontrollerstate 1" command, and retry the operation.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC992 Message Arguments Invalid job: arg1 . • arg1 = job ID Detailed Description The job ID specified in the message is invalid or was already deleted. Recommended Response Action To monitor the current set of the jobs, use the "racadm jobqueue view" command.
Recommended Response Action No response action is required. Category Configuration Subcategory RAC = RAC Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RAC994 Message Unable to run the "jobqueue delete --all" command. Detailed Description The jobs cannot be deleted if they are in one of these states: "Scheduled" or "Running".
Detailed Description The hardware inventory cannot be retrieved because of an internal error whether or not Collect System Inventory On Restart (CSIOR) is enabled or disabled. Recommended Response Action Make sure to enable Collect System Inventory On Restart (CSIOR) feature, reboot the system, and retry the operation. If CSIOR is already enabled, reboot iDRAC using "racadm racreset" command.
RAC997 Message The object DNSDomainFromDHCP cannot be enabled. Detailed Description The DHCP for Domian Name cannot be enabled if IPv4 and IPv4 DHCP or IPv6 and IPv6 AutoConfig is disabled. Recommended Response Action Make sure that IPv4 and IPv4 DHCP are enabled, or IPv6 and IPv6 AutoConfig are enabled Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RAC999 Message The object DNSFromDHCP6 cannot be enabled. Detailed Description DNSFromDHCP6 cannot be enabled if iDRAC IPv6 AutoConfig is disabled. Recommended Response Action Enable IPv6 AutoConfig using "racadm set iDRAC.IPv6.AutoConfig < 1 | Enabled >" command, and retry the operation. Category Configuration Subcategory RAC = RAC Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
RDU Event Messages 46 RDU0001 Message The fans are redundant. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID 2475 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID 5304 Server Administrator Trap ID 5304 RDU0002 Message Fan redundancy is lost.
Trap/EventID 2473 LCD Message Fan redundancy is lost. Check fans. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RDU0003 Message Fan redundancy is degraded. Detailed Description One of more fans have failed or have been removed or a configuration change occurred which requires additional fans. Recommended Response Action Remove and re-install failed fans or install additional fans.
Category System Health Subcategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID 2475 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RDU0005 Message The fans are not redundant. Insufficient resources to maintain normal operations.
Recommended Response Action No response action is required. Category System Health Subcategory RDU = Redundancy Severity Severity 3 (Informational) Trap/EventID 2475 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID 5304 Server Administrator Trap ID 5304 RDU0012 Message Power supply redundancy is lost.
RDU0013 Message Power supply redundancy is degraded. Detailed Description The current power operational mode is non-redundant because of a power supply exception, a power supply inventory change, or a system power inventory change. The system was previously operating in a power redundant mode. Recommended Response Action Check the event log for power supply failures. Review system configuration and power consumption.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RDU0015 Message The power supplies are not redundant. Insufficient resources to maintain normal operations. Detailed Description The system may power down or operate in a performance degraded state. Recommended Response Action Check the event log for power supply failures. Review system configuration and power consumption and upgrade or install power supplies accordingly.
LCD Message No LCD message display defined. Initial Default OS Log;None Server Administrator Event ID 5302 Server Administrator Trap ID Not Applicable RDU0021 Message Unable to determine the redundancy status of the power supply units. Detailed Description One of the power supply units have failed. Recommended Response Action Replace the failed power supply with a new power supply.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default OS Log;None Server Administrator Event ID 5302 Server Administrator Trap ID Not Applicable RDU0023 Message Unable to determine the redundancy status of the fans. Detailed Description One or more fans are non-functional or may have failed. Recommended Response Action Check that all fans are working properly. Replace any non-fuctional fan with a new fan.
RED Event Messages RED000 Message Unrecognized error code encountered. Detailed Description An unknown error was returned. Recommended Response Action Check the uniform resource identifier (URI) target path and make sure the repository server is available. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) Trap/EventID 6210 LCD Message No LCD message display defined.
Trap/EventID 6211 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED002 Message Package successfully downloaded. Detailed Description Package has been successfully downloaded. The Job Scheduler will schedule it at the time specified. Recommended Response Action Schedule the job if it is not already scheduled.
Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) Trap/EventID 6211 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED004 Message Job failed. Detailed Description The Job failed to execute due to an unknown error. Recommended Response Action Check the uniform resource identifier (URI), target path and make sure the repository server is available.
Recommended Response Action Provide a valid uniform resource identifier (URI) for the share location Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) Trap/EventID 6210 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED006 Message Unable to download Update Package. Detailed Description The Update Package cannot be successfully downloaded.
RED007 Message Unable to verify Update Package signature. Detailed Description The Update Package security signature cannot be verified. Recommended Response Action Re-acquire the Update Package from the service provider. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) Trap/EventID 6210 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RED009 Message Lifecycle Controller is not present. Detailed Description Lifecycle Controller is not present. Recommended Response Action Verify if Lifecycle Controller is installed on the system by pressing F10 on boot up. If the Lifecycle Controller application is not present, use the update package to reinstall it.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED0101 Message Rollback successfull. Detailed Description The firmware was rolled back to the previous version. Recommended Response Action No response action is required. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED012 Message Unable to create Lifecycle Controller update task. Detailed Description Unable to create a Lifecycle Controller update task. The related job status is marked Failed. Recommended Response Action Retry the update operation after one minute.
Subcategory RED = FW Download Severity Severity 2 (Warning) Trap/EventID 6210 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED014 Message Job for this device is already present. Detailed Description A job for this update already exists in the queue and prevents the new job from being scheduled. Recommended Response Action Delete the existing job before scheduling a new update job.
Recommended Response Action The supported protocols include NFS, CIFS, HTTP, FTP, TFTP Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) Trap/EventID 6210 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED016 Message Mount of remote share failed. Detailed Description The remote share location that has the ISO image did not mount correctly.
RED017 Message The DUP specified is not compatible with the target system. Detailed Description The DUP specified is not compatible with the target system. Recommended Response Action Download and use the DUP that matches the system that the installation is targeting. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RED019 Message Reinstall or Rollback cannot be performed since no applicable firmware was found on the Lifecycle Controller. Detailed Description Reinstall or Rollback cannot be performed since no applicable firmware was found on the Lifecycle Controller. Recommended Response Action Directly update to the desired version. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED021 Message The component InstanceID specified is not present on the system. Detailed Description The component InstanceID specified could not be located on the system. Recommended Response Action Ensure the component specified for updates is present in the system.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED023 Message Lifecycle Controller in use. This job will start when Lifecycle Controller is available. Detailed Description The Lifecycle Controller is unable to access internal storage currently in use by another operation. Recommended Response Action Wait for the Lifecycle Controller task to complete.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED025 Message Arguments arg1 firmware updated successfully. Current version: arg2 • arg1 = device name • arg2 = firmware version Detailed Description The firmware for the indicated device updated successfully to the identified firmware version. Recommended Response Action No response action is required.
Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED027 Message Insufficient space to upload the requested file. Detailed Description The temporary storage is full. The uploaded files must be installed to clear space for additional uploads.
Recommended Response Action Select one or more update files to install. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED029 Message A reboot is pending. Detailed Description This task will reboot the system at the scheduled start time. Recommended Response Action No response action is required.
Detailed Description The system reboot is complete. Recommended Response Action No response action is required. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log;None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED031 Message Approaching maximum size limit allowed for storing firmware images.
RED032 Message Reached maximum size limit allowed for storing firmware images. Deleted all rollback firmware images. Detailed Description The rollback firmware images previously stored were deleted to provide space for storing the firmware images for the requested operation. All the rollback firmware images are deleted. Recommended Response Action No response action is required.
Server Administrator Trap ID Not Applicable RED034 Message Firmware update in progress. Detailed Description A firmware update operation is currently in progress. Recommended Response Action Check the firmware update job status. Wait for the current job to complete. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message rollback successful Initial Default LC Log;None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED036 Message Arguments Firmware updates are available : arg1 • arg1 = component name Detailed Description Firmware updates are available for component identified in the message in the specified remote repository and it is recommended to update to the firmware available in the reposit
Recommended Response Action No response action is required. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED038 Message Arguments A recurring task of type arg1 is added.
RED039 Message Arguments Settings for a recurring operation of type arg1 were cleared. • arg1 = operation label Detailed Description Settings for an Automatic Server Profile Backup, Automatic Update, or other recurring operations identified in the message were cleared. The recurring operation identified in the message is deleted. Recommended Response Action No response action is required.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED041 Message Arguments A recurring operation of type arg1 was not created because the required license is not available. • arg1 = operation type Detailed Description The license required to perform the operation identified in the message is expired or is not available.
Recommended Response Action Use a username that has the necessary access rights and retry the operation. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message A recurring task was not created because the required user authority is not present.
RED044 Message Arguments A recurring operation of type arg1 was unable to create a job because the required license is not available now. • arg1 = operation type Detailed Description The license required to perform the operation identified in the message either has expired or was removed and the iDRAC was unable to create the next job in the sequence. Recommended Response Action Install an iDRAC license that supports the following features: Automatic Update or Server Profile Export and Import.
Severity Severity 3 (Informational) LCD Message A recurring task was unable to create a job because the required user authority is no longer present. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED046 Message Arguments A recurring operation of type arg1 was unable to create a job because the task type is now disabled.
Arguments • arg1 = operation type Detailed Description An Automatic Server Profile Backup or Automatic Update operation is already configured. Recommended Response Action Clear the existing configuration settings for the operation identified in the message and retry the operation. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message A recurring task was not created because a task of that type is already present.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED049 Message Arguments The job arg1 is deleted because the recurring operation arg2 is currently not enabled. • arg1 = job ID • arg2 = operation type Detailed Description When an Automatic Backup or Automatic Update recurring operation is disabled or the license for this feature is expired, the next job in the sequence had not started yet and was deleted.
Recommended Response Action Check the network connection and access to the update package from the iDRAC. Verify that the user access credentials and proxy server settings are correct. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined.
RED052 Message Processing of update packages is starting. Detailed Description Processing of update packages is starting. Attempting a manual update will not be possible until current update package processing is completed. Recommended Response Action No response action is required. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RED054 Message Arguments An update job arg1 was created. • arg1 = job ID Detailed Description A job for applying an update package was created. Recommended Response Action No response action is required. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED056 Message An internal error occurred. Unable to complete the specified operation. Detailed Description An internal error occurred because of insufficient memory available on iDRAC. Recommended Response Action Retry the operation. If the issue persists, reset the iDRAC and retry the operation.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED058 Message Arguments A repository update job arg1 was created. • arg1 = job ID Detailed Description A repository update job with the job ID identified in the message was created. Recommended Response Action No response action is required.
Recommended Response Action Retry the operation for the component identified in the message. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED060 Message The specified repository catalog is not supported.
RED061 Message The job is successfully scheduled. Detailed Description The job is successfully scheduled. The job will automatically start at the specified start time. Recommended Response Action No response action is required. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable RED063 Message Arguments The iDRAC firmware updated successfully. Previous version: arg1 , Current version: arg2 • arg1 = available firmware version • arg2 = installed firmware version Detailed Description The iDRAC firmware updated successfully to the firmware version identified in the message. Recommended Response Action No response action is required.
Trap/EventID 6211 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED065 Message The recurring scheduled update from repository job completed and updates were applied. A system restart was not required. Detailed Description The recurring scheduled update from repository job completed and updates were applied. A system restart was not required.
Recommended Response Action A system restart is required to apply the staged updates. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) Trap/EventID 6211 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED067 Message The recurring scheduled update from repository job completed and updates were staged.
RED068 Message Arguments Unable to successfully complete arg1 : arg2 • arg1 = job ID • arg2 = job result message Detailed Description Unable to successfully complete the job identified in the message. Recommended Response Action For more information about the job, view the job queue. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED071 Message Unable to get the Automatic Backup schedule information. Detailed Description Unable to get the Automatic Backup schedule information because the schedule is not configured. Recommended Response Action Configure the Automatic Backup schedule. Category Configuration Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED073 Message Arguments The input value entered for the parameter arg1 is invalid. • arg1 = parameter Detailed Description The operation did not complete successfully because of an invalid value for the parameter identified in the message. Recommended Response Action Verify the value for the parameter identified in the message is valid and retry the operation.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED075 Message An Automatic Backup schedule already exists. Detailed Description The Automatic Backup schedule operation could not be successfully created because the Automatic Backup schedule configuration already exists.
Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED077 Message Unable to get the Automatic Update schedule information. Detailed Description Unable to get the Automatic Update schedule information because the schedule is not configured. Recommended Response Action Configure the Automatic Update schedule.
Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED079 Message Arguments The input value entered for the parameter arg1 is invalid. • arg1 = parameter Detailed Description The operation did not complete successfully because of an invalid value for the parameter identified in the message.
Detailed Description The operation did not complete successfully because the required parameters identified in the message is not present in the method invocation. Recommended Response Action Verify that all required parameters for the method are present and retry the operation. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined.
RED082 Message The requested job cannot be scheduled, because job schedule type such as Automatic Backup or Automatic Update is not enabled. Detailed Description The Automatic Update or Automatic Backup feature is disabled. Recommended Response Action Enable the correct job schedule type, and then retry the operation. For example, to enable the Automatic Update feature, select the Enable Automatic Update option.
Server Administrator Trap ID Not Applicable RED084 Message Unable to update the Chassis firmware because of an issue in the communication between iDRAC and Chassis Management Controller (CMC). Detailed Description The Chassis firmware cannot be updated because of an issue in the communication between iDRAC and CMC. Recommended Response Action Verify the status of CMC by accessing the CMC and making sure it is functioning and responding and then retry the operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED086 Message Unable to update the Chassis firmware, Chassis Management at Server is not set to Monitor and Configure. Detailed Description The Chassis firmware cannot be updated because the Chassis Management at Server (CMAS) attribute is incorrectly set. The CMAS attribute must be set to Monitor and Configure on the CMC in order to update CMC firmware from and iDRAC.
Recommended Response Action Make sure that the Allow CHC Updates Through OS and Lifecycle Controller setting is set to Enabled, and then retry the operation. Using the iDRAC Web UI, select iDRAC > Update, click on the Settings tab, select Enabled for the setting and then click Apply button. Category Updates Subcategory RED = FW Download Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description A Chassis firmware update operation is in progress. Any attempt to update Chassis firmware during this period will be unsuccessful. Recommended Response Action No response action is required. Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RED091 Message Unable to install Lifecycle Controller firmware. Detailed Description Unable to install Lifecycle Controller firmware. Recommended Response Action Reinstall the iDRAC7 firmware (DUP) to repair Lifecycle Controller. For more information, see Lifecycle Controller Users Guide. Category Updates Subcategory RED = FW Download Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED093 Message The requested job cannot be scheduled because Lifecycle Controller is not enabled. Detailed Description Lifecycle Controller is not enabled and must be enabled in order for scheduled jobs to be created. Recommended Response Action Enable Lifecycle Controller and retry the operation.
Category Updates Subcategory RED = FW Download Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RED095 Message rSPI update for Diags failed.
RFL Event Messages 48 RFL2000 Message Arguments Internal Dual SD Module arg1 is present. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory RFL = IDSDM Media Severity Severity 3 (Informational) Trap/EventID 2211 LCD Message No LCD message display defined.
Category System Health Subcategory RFL = IDSDM Media Severity Severity 2 (Warning) Trap/EventID 2210 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID 5303 Server Administrator Trap ID Not Applicable RFL2003 Message Arguments Internal Dual SD Module arg1 is online. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
Arguments • arg1 = name Detailed Description The SD card module is installed but improperly configured or failed to initialize. Recommended Response Action Reinstall the SD module and remove and reinstall SD cards. Category System Health Subcategory RFL = IDSDM Media Severity Severity 1 (Critical) Trap/EventID 2209 LCD Message Internal Dual SD Module failed.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFL2006 Message Arguments Internal Dual SD Module arg1 is write protected. • arg1 = name Detailed Description The module is write-protected. Changes may not be written to the media. Recommended Response Action if unintended, remove the media and disable write protection.
Category System Health Subcategory RFL = IDSDM Media Severity Severity 3 (Informational) Trap/EventID 2211 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFL2008 Message Arguments Internal Dual SD Module arg1 is disabled. • arg1 = name Detailed Description The Internal Dual SD Card redundancy feature was disabled. The SD card identified in the message is disabled.
Arguments • arg1 = name Detailed Description The Internal Dual SD Card redundancy feature was enabled. The SD card identified in the message is enabled. Recommended Response Action No response action is required. Category System Health Subcategory RFL = IDSDM Media Severity Severity 3 (Informational) Trap/EventID 2211 LCD Message No LCD message display defined.
RFLA Event Messages RFLA2001 Message Arguments Internal Dual SD Module arg1 is absent. • arg1 = name Detailed Description The SD card module is not detected or not installed. Recommended Response Action If unintended, reinstall the SD module. Category System Health Subcategory RFLA = IDSDM Absent Severity Severity 1 (Critical) Trap/EventID 2481 LCD Message Internal Dual SD Module is absent. Check SD card.
RFM Event Messages 50 RFM1018 Message Removable Flash Media is absent. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory RFM = FlexAddress SD Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFM1019 Message Removable Flash Media is present.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFM1020 Message Removable Flash Media is IPMI-function ready. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory RFM = FlexAddress SD Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFM1022 Message Removable Flash Media is ready. Detailed Description None Recommended Response Action If unintended, reinstall the flash media. Category System Health Subcategory RFM = FlexAddress SD Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFM1024 Message Removable Flash Media is offline. Detailed Description At boot, the Card Identification (CID) signature of the card is different from the Non-volatile (NV) storage value or the card is the destination of a copy operation that is in-progress.
Subcategory RFM = FlexAddress SD Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFM1026 Message Failure detected on Removable Flash Media. Detailed Description An error is reported during a SD card read or write. Recommended Response Action Re-install the flash media, if the issue persists replace the media.
Category System Health Subcategory RFM = FlexAddress SD Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFM1028 Message Removable Flash Media was activated. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory RFM = FlexAddress SD Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFM1030 Message Removable Flash Media is booting. Detailed Description None Recommended Response Action No response action is required.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory RFM = FlexAddress SD Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFM1032 Message Removable Flash Media is write protected. Detailed Description The card is write-protected by the physical latch on the SD card.
RFM1033 Message Removable Flash Media is writable. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory RFM = FlexAddress SD Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RFM1034 Message Media not present for Removable Flash Media.
Server Administrator Trap ID Not Applicable RFM1035 Message Media is present for Removable Flash Media. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory RFM = FlexAddress SD Severity Severity 3 (Informational) LCD Message No LCD message display defined.
RRDU Event Messages 51 RRDU0001 Message Internal Dual SD Module is redundant. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory RRDU = IDSDM Redundancy Severity Severity 3 (Informational) Trap/EventID 2491 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID 5304 Server Administrator Trap ID 5304 RRDU0002 Message Internal Dual SD Module redundancy is lost.
Trap/EventID 2489 LCD Message Internal Dual SD Module redundancy lost. Check SD cards Initial Default IPMI Alert;LC Log Server Administrator Event ID 5306 Server Administrator Trap ID 5306 RRDU0003 Message Internal Dual SD Module redundancy is degraded. Detailed Description Either one of the SD card or both the SD cards are not functioning properly. Recommended Response Action Replace the failed SD card.
Category System Health Subcategory RRDU = IDSDM Redundancy Severity Severity 3 (Informational) Trap/EventID 2491 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RRDU0005 Message Internal Dual SD Module is not redundant. Insufficient resources to maintain normal operations. Detailed Description The current operating configuration cannot maintain redundancy.
Recommended Response Action No response action is required. Category System Health Subcategory RRDU = IDSDM Redundancy Severity Severity 3 (Informational) Trap/EventID 2491 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RRDU0007 Message Internal Dual SD Module rebuild completed successfully. Detailed Description Internal Dual SD Module rebuild completed successfully.
RRDU0008 Message Internal Dual SD Module rebuild did not complete successfully. Detailed Description Internal Dual SD Module rebuild failed because read/write to one of the SD cards failed. Recommended Response Action Replace the failed SD card and retry rebuild. Category System Health Subcategory RRDU = IDSDM Redundancy Severity Severity 1 (Critical) Trap/EventID 2489 LCD Message Internal Dual SD Module rebuild failed. Replace failed SD card.
Server Administrator Trap ID Not Applicable RRDU0011 Message Unable to determine the redundancy status of the Internal SD Module. Detailed Description This occurs because of one of the following reasons: 1) Either one of the SD card or both the SD cards have failed. 2) The Internal SD Module has failed. Recommended Response Action Replace the failed SD card with a new SD card, or replace the Internal SD Module. For more information, contact your service provider.
RSI Event Messages 52 RSI0001 Message The Lifecycle Controller Remote Services is available. Detailed Description The Lifecycle Controller Remote Services instrumentation is available. Recommended Response Action No response action is required. Category Configuration Subcategory RSI = Remote Service Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable RSI0003 Message The remote service is reloading data Detailed Description The Remote Service database is being updated. Recommended Response Action Retry request later. Category Configuration Subcategory RSI = Remote Service Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined.
SEC Event Messages 53 SEC0000 Message The chassis is open. Detailed Description The chassis is open. System performance may be degraded, and security may be compromised. Recommended Response Action Close the chassis. Check system logs. Category System Health Subcategory SEC = Security Event Severity Severity 1 (Critical) Trap/EventID 2385 LCD Message Intrusion detected.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0002 Message The I/O card area is open. Detailed Description The I/O card area is open. I/O cards may be added or removed. System performance may be degraded. Recommended Response Action Close the I/O card area. Check system logs.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0004 Message The LAN is disconnected. Detailed Description The LAN is disconnected. Network performance may be degraded. Recommended Response Action If unintentional, connect network cable.
Subcategory SEC = Security Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0006 Message The fan area is open. Detailed Description The fan area is open. System performance may be degraded. Recommended Response Action Close the fan area. Check system logs.
Category System Health Subcategory SEC = Security Event Severity Severity 3 (Informational) Trap/EventID 2387 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID 5252 Server Administrator Trap ID 5252 SEC0017 Message The drive bay is closed. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory SEC = Security Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0019 Message The processor area is closed. Detailed Description None Recommended Response Action No response action is required.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEC = Security Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0021 Message The docking is authorized. Detailed Description None Recommended Response Action No response action is required.
SEC0022 Message The fan area is closed. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEC = Security Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0031 Message The chassis is open while the power is on. Detailed Description The chassis is open.
Server Administrator Trap ID Not Applicable SEC0032 Message The chassis is closed while the power is on. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEC = Security Event Severity Severity 3 (Informational) Trap/EventID 2387 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0034 Message The chassis is closed while the power is off. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEC = Security Event Severity Severity 3 (Informational) Trap/EventID 2387 LCD Message No LCD message display defined.
Trap/EventID 2385 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0041 Message BIOS is unable to configure the Intel Trusted Execution Technology (TXT). Detailed Description TXT initialization cannot be completed because system configuration may have changed.
Category System Health Subcategory SEC = Security Event Severity Severity 1 (Critical) Trap/EventID 2385 LCD Message Problem with TXT operation. Reconfigure TPM and TXT in BIOS. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0043 Message BIOS Authenticated Code Module detected an Intel Trusted Execution Technology (TXT) problem during POST.
Detailed Description TXT initialization cannot be completed because system configuration may have changed. Recommended Response Action Check system hardware inventory for TPM presence, clear and reconfigure TPM and TXT in BIOS setup menu. Category System Health Subcategory SEC = Security Event Severity Severity 1 (Critical) Trap/EventID 2385 LCD Message TXT problem at boot. Reconfigure TPM and TXT in BIOS.
SEC0051 Message Unable to determine the redundancy status of the chassis intrusion sensor. Detailed Description The chassis may be open. This condition can lead to degraded system performance because of insufficient cooling and the system security may be compromised. Recommended Response Action Close the chassis. Category System Health Subcategory SEC = Security Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SEC0600 Message A secure mode violation detected. Detailed Description This may apply to a physical or remote access attempt. Recommended Response Action Check system logs for intrusion attempts, and ensure strong password policies. Category System Health Subcategory SEC = Security Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0602 Message User password violation detected. Detailed Description This may apply to a physical or remote access attempt. Recommended Response Action Check system logs for intrusion attempts, and ensure strong password policies. Category System Health Subcategory SEC = Security Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0604 Message A setup password violation detected. Detailed Description This may apply to a physical or remote access attempt. Recommended Response Action Check system logs for intrusion attempts, and ensure strong password policies. Category System Health Subcategory SEC = Security Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0606 Message The network boot password violation detected. Detailed Description This may apply to a physical or remote access attempt. Recommended Response Action Check system logs for intrusion attempts, and ensure strong password policies.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0608 Message A password violation detected. Detailed Description This may apply to a physical or remote access attempt. Recommended Response Action Check system logs for intrusion attempts, and ensure strong password policies.
Subcategory SEC = Security Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0610 Message An Out-of-band password violation detected. Detailed Description This may apply to a remote access attempt. Recommended Response Action Check system logs for intrusion attempts, and ensure strong password policies.
Category System Health Subcategory SEC = Security Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEC0700 Message Warning: Default username and password are currently in use. It is strongly recommended to change the default password before configuring the propery. Else, it causes a severe security risk for iDRAC.
Detailed Description This warning message is displayed when using the default username and password (root and calvin). Using the default password causes a severe security risk for iDRAC. Recommended Response Action To change the password, run the following racadm commands: racadm set iDRAC.Users..Password . Alternatively, to avoid this warning message run the following racadm command: racadm set iDRAC.Tuning.
SEL Event Messages 54 SEL0002 Message Logging is disabled. Detailed Description This message appears when event logging of a specific type is disabled by the user. (IPMI sensor type code 10h - offset 01h) Recommended Response Action If unintended, re-enable logging. Category System Health Subcategory SEL = Sys Event Log Severity Severity 1 (Critical) Trap/EventID 2377 LCD Message No LCD message display defined.
Trap/EventID 2379 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL0004 Message Log cleared. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID 2379 LCD Message No LCD message display defined.
Category System Health Subcategory SEL = Sys Event Log Severity Severity 1 (Critical) Trap/EventID 2377 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL0007 Message All event logging is enabled. Detailed Description None Recommended Response Action No response action is required.
Detailed Description When the event log is full, additional events are not written to the log; or older events will be overwritten and lost. This message may also appear if the user disabled event logging. (IPMI sensor type code 10h - offset 04h) Recommended Response Action Backup and clear log. Category System Health Subcategory SEL = Sys Event Log Severity Severity 1 (Critical) Trap/EventID 2377 LCD Message SEL is full.
SEL0012 Message Could not create or initialize the system event log. Detailed Description if the system event log failed to initialize platform status and failure events are not captured. Some management software will not report platform exceptions. Recommended Response Action Reboot the management controller or iDRAC. Cycle system input power. If problem persists call support.
Server Administrator Trap ID Not Applicable SEL0014 Message Arguments The System Event Log (SEL) was cleared by arg1 from arg2 . • arg1 = username • arg2 = IP address Detailed Description The System Event Log (SEL) was cleared by the username identified in the message from the IP address identified in the message. Recommended Response Action No response action is required.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1202 Message OEM system boot. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Trap/EventID 2377 LCD Message Unknown system hardware failure. Contact support Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1205 Message The unknown system hardware failure was corrected. Detailed Description None Recommended Response Action No response action is required.
Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1207 Message An entry was removed from auxiliary log. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1209 Message The platform event filter action failed. Detailed Description System policies or permissions may prevent the action from executing.
Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1211 Message The time-stamp clock could not be synchronized.
SEL1300 Message No bootable media found. Detailed Description System setup displays the system boot order. The local video screen may also show additional information. (IPMI sensor type code 1eh - offset 00h) Recommended Response Action Check system boot settings. Check mass storage controller configuration settings is applicable. Category System Health Subcategory SEL = Sys Event Log Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SEL1302 Message Non-bootable diskette detected. Detailed Description The disk in the drive is not formatted correctly or does not contain the necessary operating system files(IPMI sensor type code 1eh - offset 01h) Recommended Response Action Replace diskette with bootable disk. Category System Health Subcategory SEL = Sys Event Log Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1304 Message The PXE server not found. Detailed Description PXE is one way to boot a system from the network. (IPMI sensor type code 1eh offset 02h) Recommended Response Action Check network and PXE server configuration. Category System Health Subcategory SEL = Sys Event Log Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1306 Message Invalid boot sector found. Detailed Description The disk in the drive is not formatted correctly or does not contain the necessary operating system files (IPMI sensor type code 1eh - offset 03h) Recommended Response Action Replace diskette with bootable disk.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1308 Message A time-out occurred while waiting for user to select a boot source. Detailed Description The system has failed to boot to an operating system and needs the user to select a boot source. (IPMI sensor type code 1eh - offset 04h) Recommended Response Action Select boot source within the time allowed.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1400 Message The platform generated a page alert. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1404 Message A platform event trap (PET) was generated. Detailed Description None Recommended Response Action No response action is required.
Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1500 Message The chassis management controller (CMC) is redundant. Detailed Description None Recommended Response Action No response action is required.
Recommended Response Action Check CMC network cables and network connections. Check that CMC firmware versions match. Category System Health Subcategory SEL = Sys Event Log Severity Severity 1 (Critical) Trap/EventID 2377 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1502 Message Chassis management controller (CMC) redundancy is degraded.
SEL1503 Message The chassis management controller (CMC) is not redundant. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID 2379 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1506 Message Arguments Lost communications with Chassis Group Member arg1 . • arg1 = number Detailed Description The primary CMC has lost communication with the indicated member CMC. Recommended Response Action Check network cable and network connections.
Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID 2379 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1508 Message Arguments Member arg1 could not join the Chassis Group. • arg1 = number Detailed Description The indicated member may be a member of another chassis group or may be incompatible with membership.
Arguments • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID 2379 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1510 Message Arguments An authentication error detected for Chassis Group Member arg1 .
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL1511 Message Arguments Member arg1 removed from the Chassis Group. • arg1 = number Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) Trap/EventID 2379 LCD Message No LCD message display defined.
Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SEL9901 Message OEM software event. Detailed Description The current software version cannot decode this event.
Detailed Description Software on the system has logged an event that cannot be determined. You may need to review this event using a tool which displays raw data such as Ipmitool with the -vvv option or Racadm with the -E option. Recommended Response Action No response action is required. Category System Health Subcategory SEL = Sys Event Log Severity Severity 3 (Informational) LCD Message No LCD message display defined.
SSD Event Messages 55 SSD1001 Message Arguments Write-cache on arg1 is enabled. • arg1 = PCIe SSD name Detailed Description Write-cache is enabled on the PCIe solid state drive (SSD) identified in the message. Recommended Response Action No response action is required. Category Storage Subcategory SSD = PCIe SSD Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Subcategory SSD = PCIe SSD Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2428 Server Administrator Trap ID 90300 SSD1003 Message Arguments arg1 is ready for removal. • arg1 = PCIe SSD name Detailed Description The PCIe solid state drive (SSD) identified in the message is ready for removal. Recommended Response Action No response action is required.
Detailed Description The log file of the PCIe solid state drive (SSD) identified in the message is successfully exported. Recommended Response Action No response action is required. Category Storage Subcategory SSD = PCIe SSD Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2430 Server Administrator Trap ID 90100 SSD1005 Message Arguments Successfully initialized arg1 .
SSD1006 Message Arguments The arg1 has reached arg2 of warranted device wear-out limit. • arg1 = PCIe solid state device name • arg2 = percent Detailed Description The PCIe solid state device identified in the message is approaching the warranted wear-out limit. Recommended Response Action No response action is required. Category Storage Subcategory SSD = PCIe SSD Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID 2434 Server Administrator Trap ID 90300 SSD1008 Message Arguments The arg1 is approaching read-only mode. • arg1 = PCIe solid state device name Detailed Description The PCIe solid state device identified in the message is between 90% and 100% of reaching read-only mode. Recommended Response Action No response action is required. Category Storage Subcategory SSD = PCIe SSD Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory SSD = PCIe SSD Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2436 Server Administrator Trap ID 90400 SSD1010 Message Arguments The arg1 is in a security locked state. • arg1 = PCIe solid state device name Detailed Description The PCIe solid state device identified in the message is in a locked state, because an existing initialization task was interrupted due to a power failure or disk removal.
STOR Event Messages 56 STOR003 Message Missing parameter. Detailed Description Required parameter is missing. Recommended Response Action Refer to the RAID profile to determine required parameters. Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR004 Message Invalid parameter value.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR006 Message Unable to complete the operation. Detailed Description The operation could not be completed because of an issue with the management controller (either the iDRAC or the Chassis Management Controller (CMC)) that is managing the storage. Recommended Response Action Retry the operation. If the issue persists, contact your service provider.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR009 Message Physical disk FQDD did not identify a valid physical disk for the operation. Detailed Description Physical disk did not identify valid physical disk for the operation. Recommended Response Action Provide compatible physical disk with the operation.
Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR0101 Message No RAID controller is displayed. Detailed Description No RAID controller data to display. The system is powered off, no RAID controller is present in the system, or the RAID controller is not connected to the system.
Category Storage Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR0103 Message No physical disks are displayed. Detailed Description No physical disk data to display.
Recommended Response Action Check if the server has power, physical disks are available, and virtual disks are created. Category Storage Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR0105 Message No enclosures are displayed. Detailed Description No enclosure data to display.
Detailed Description No fan data to display. The system is powered off, no fan enclosures are present in the system, or the fans are not connected to the enclosures. Recommended Response Action Check if the server has power, enclosure fan is available, and fan is connected to the enclosure. Category Storage Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
STOR0108 Message Temperature probes are not connected to enclosures or data about temperature is unavailable. Detailed Description No temperature data to display. The system is powered off, no enclosure temperature probes are present in the system, or the temperature probes are not connected to the enclosures. Recommended Response Action Check if the server has power, enclosure temperature probe is available, and temperature probe is connected to the enclosure.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR011 Message Stripe size not supported on controller. Detailed Description The operation cannot be completed because the stripe size entered is not supported by the controller. Recommended Response Action Enter a valid stripe size and retry the operation. Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR0111 Message Invalid reference key. Detailed Description The specified reference key is invalid. Recommended Response Action Verify that the correct reference key is specified. See the help text or documentation for valid reference keys. Category Storage Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR013 Message One or more storage device(s) are not in a state where the operation can be completed. Detailed Description One or more storage device(s) are in a state that prevents the operation from completing.
Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR016 Message The physical disk specified is not large enough to be a hot spare for this virtual disk. Detailed Description The physical disk drive cannot be assigned as the hot-spare of this virtual disk because the capacity of the physical disk is not sufficient.
Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR018 Message No foreign drives detected. Detailed Description This operation did not detect any foreign drives. This may be because no foreign drives are present or the only foreign drives are in a secured state.
Recommended Response Action Enter a passphrase that meets the passphrase character criteria of the controller, and then retry the operation. Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR020 Message A controller key is already present.
Detailed Description Installing Storage Services and Array Manager on the same system is not a supported configuration. Storage Services is not installed on a system where Array Manager is installed. Recommended Response Action Uninstall either Storage Services or Array Manager and retry the operation. Category Storage Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
STOR0202 Message Arguments The configuration file (Path: arg1 ) that contains firmware and driver information for arg2 is not updated or is incorrectly formatted to complete the comparison. • arg1 = file path • arg2 = controller name Detailed Description Storage Services is unable to determine whether the system has the minimum required versions of the RAID controller firmware and drivers because a configuration file is not readable, corrupted, or has missing data.
Initial Default None Server Administrator Event ID 2167 Server Administrator Trap ID 10300 STOR0204 Message The non-RAID SCSI driver version is older than the minimum required version. Detailed Description The driver version does not meet the minimum requirements and Storage Services cannot perform the required operations until the minimum requirements are met.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2261 Server Administrator Trap ID 75100 STOR0206 Message Smart thermal shutdown feature is enabled. Detailed Description The storage shutdown feature based on high ambient temperature (smart themal shutdown) is enabled. Recommended Response Action No response action is required.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2263 Server Administrator Trap ID 10100 STOR0208 Message Protection policy has changed. Detailed Description A new protection policy is created or an existing protection policy is modified. Recommended Response Action No response action is required.
Category Storage Subcategory STOR = Storage Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2314 Server Administrator Trap ID 10400 STOR021 Message The controller key is not present. Detailed Description The virtual disk cannot be secured because a controller key is not present. Recommended Response Action Set an appropriate controller key and retry the operation.
Detailed Description A SCSI device may have experienced an error that generated sense data after the device recovery. Recommended Response Action No response action is required. Category Storage Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2095 Server Administrator Trap ID 75100;85100;90100 STOR0211 Message Arguments The arg1 has returned to normal state.
STOR0212 Message Arguments The arg1 has failed. • arg1 = device name Detailed Description The device (physical disk or an enclosure) identified in the message has failed. The device (physical disk or an enclosure) failure was detected while performing a rescan. However, physical disk failures are also detected during a check consistency operation. Recommended Response Action Replace the identified device. A failed device is inidicated with a red color "X" status icon.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR023 Message Unable to perform configuration operations because a configuration job for the device already exists. Detailed Description Unable to perform configuration operations because a configuration job for the device already exists. Recommended Response Action Wait for the current job for the device to complete or cancel the current job before attempting more configuration operations on the device.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR025 Message Unable to delete any pending configuration because the configuration job is already scheduled. Detailed Description The pending configuration cannot be deleted because the configuration job is already scheduled.
Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR027 Message Virtual Disk name is not supported. Detailed Description Setting the Virtual disk name is not a valid operation on the specified controller. Recommended Response Action Do not specify the virtual disk name and retry the operation.
Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR029 Message Physical disk not found. Detailed Description The requested operation cannot be completed because the specified physical disk is not found.
Recommended Response Action Provide a valid controller FQDD (Fully Qualified Device Descriptor) and retry the operation. Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR031 Message Lifecycle Controller is not enabled.
STOR032 Message Lifecycle Controller is currently in use. Detailed Description Lifecycle Controller is unable to gain access to internal storage because it is in use by another application or operation. Recommended Response Action Wait for current Lifecycle Controller operation to complete.
Server Administrator Trap ID Not Applicable STOR034 Message Invalid parameter value for RebootJobType. Detailed Description The requested operation cannot be completed because an invalid value is specified for RebootJobType. Recommended Response Action Enter a valid RebootJobType value and retry the operation. For more information about the RebootJobType parameter, see the RAID Profile specification.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR037 Message Arguments Missing required parameter arg1 . • arg1 = parameter name Detailed Description Unable to complete the requested operation because one or more input parameters identified in the message are not specified. Recommended Response Action Enter all the required parameters and retry the operation.
Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR039 Message Mismatch in AttributeName and AttributeValue count. Detailed Description Unable to complete the requested operation because of a mismatch in the number of AttributeName and AttributeValue values specified.
Recommended Response Action Specify a valid AttributeName value for the attribute identified in the message and retry the operation. Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
STOR042 Message Arguments Unsupported value for AttributeName arg1 • arg1 = attribute name Detailed Description Unable to complete the requested operation because the attribute value specified is not supported in the current configuration. Recommended Response Action Specify a value for the attribute identified in the message by using one of the possible values currently available for that attribute.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR044 Message All physical disks specified are not part of the same disk group. Detailed Description One or more physical disks specified to create virtual disk (VD) is not valid because it is not part of the same disk group. Recommended Response Action Enumerate existing virtual disks to find the physical disks of the same disk group.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR046 Message The specified StartingLBA and Size values combination result in an overlapping virtual disk. Detailed Description Unable to complete the create virtual disk operation because the StartingLBA and Size value combination results in an overlapping virtual disk. Recommended Response Action Refer to the users guide to provide the correct StartingLBA and Size combination values.
Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR048 Message Controller is not Dell Key Management capable. Detailed Description Either the controller or the firmware on the controller does not support the Dell Key Management feature. Recommended Response Action No response action is required.
Category Configuration Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR050 Message Controller is in Dell Key Management mode. Detailed Description The controller is in Local Key Management mode. Recommended Response Action No response action is required.
Recommended Response Action Do one of the following and retry the operation: 1) Exit the RAID Configuration wizard. 2) Update the RAID controller firmware to the latest version. 3) Reboot the system and press the key to re-enter Lifecycle Controller, and retry the operation. Category Storage Subcategory STOR = Storage Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Detailed Description Existing RAID configuration was successfully erased. Recommended Response Action No response action is required. Category Storage Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR0504 Message Successfully completed RAID operation. Detailed Description The RAID operation was successful.
STOR0505 Message Unable to delete virtual disks. Detailed Description Unable to delete the existing virtual disks for unknown reasons. Recommended Response Action Exit the RAID Configuration wizard and retry the operation. If the problem persists do the following: 1) Reboot the system. 2) Press the key to re-enter Lifecycle Controller. 3) Retry the operation. Category Storage Subcategory STOR = Storage Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable STOR0507 Message Insufficient physical disk space on selected RAID controller. Detailed Description The RAID controller does not have sufficient number of initialized physical disks or adequate disk space to create the requested virtual disk. Recommended Response Action Connect additional physical disks to the RAID controller, initialize the physical disks, and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR0509 Message No RAID levels are supported. Detailed Description The controller does not have the minimum number of initialized disks to create a virtual disk. Recommended Response Action Connect required number of initialized physical disks to the RAID controller and retry the operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR0510 Message Encryption configuration failed. Detailed Description Unable to apply the RAID controller encryption because RAID controller is not reponding. Recommended Response Action Retry the operation. If the problem persists, reboot the system or update the RAID controller firmware to the latest version and retry the operation.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR0512 Message Unable to apply the encryption key. Detailed Description Unable to apply the encryption key due to an internal error. Recommended Response Action Exit Lifecycle Controller, press the key to re-enter Lifecycle Controller, and retry the operation.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR0514 Message Unable to initialize the selected physical disk drive(s). Detailed Description The physical disk drive(s) cannot be initialized because the selected RAID controller does not support this operation while in non-RAID mode.
Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR053 Message The controller key is not present. The key must be retrieved from the Dell Key Management Server. Detailed Description The system could not obtain a controller key from the Dell Key Management Server.
Category Configuration Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR058 Message This operation is not supported on this device. Detailed Description The operation is not supported on the target device. Recommended Response Action For more information, see Lifecycle Controller-Remote Services documentation.
Recommended Response Action Create a virtual disk and retry the operation. Category Configuration Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR060 Message Configuration operations are not supported on the specified storage controller.
Detailed Description The initializing virtual disk operation is not supported on the target device. Recommended Response Action For more information about supported operations, see the documentation specific for the targeted RAID controller or the Lifecycle Controller Remote Services Quick Start Guide. Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
STOR063 Message Unable to assign the specified virtual disk to multiple Virtual Adapters in single assignment mode. Detailed Description In order to prevent data loss, the system has prevented the assignment of a Virtual Disk to multiple Virtual Adapters because the clustered assignment mode is not enabled. Recommended Response Action Enable clustered assignment mode or unassign the virtual disk from the Virtual Adapter it is currently assigned to and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR065 Message One or more physical disks specified for creating a virtual disk are not T10 Protection Information capable. Detailed Description Unable to create the requested virtual disk because one or more specified physical disk(s) is not T10 Protection Information capable.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR067 Message Controller does not support uneven span RAID10 virtual disks. Detailed Description The operation did not succeed since the selected controller does not support creating uneven span RAID10 virtual disks. Recommended Response Action The selected controller is not capable of creating an uneven span RAID10 virtual disk.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR069 Message Arguments Unable to run the arg1 method, because the number of elements entered for VDPropNameArry and VDPropValueArray is unequal.
Detailed Description The method name identified in the message could not be successfully completed, because the number of elements entered for VDPropNameArry and VDPropValueArray is not equal. Recommended Response Action Enter a valid parameter, and then retry the operation. For more information about a valid parameter, refer to the SimpleRAIDProfile document available at Dell Tech Center http://en.community.dell.com/techcenter/extras/m/white_papers/ 20263535.
STOR0702 Message Arguments The value entered for the arg1 option is invalid • arg1 = option name Detailed Description The value entered for the option name identified in the message is invalid. Recommended Response Action For more information, run the RACADM command "racadm raid help createvd". Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR072 Message iDRAC Service Module (ISM) is either not present or not running on the server OS. Detailed Description The configuration operation could not be performed because it requires iDRAC Service Module (ISM) service to be present and running in the server Operating System.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR074 Message The requested RAID configuration operation is not allowed because the controller is currently in Non-RAID mode. Detailed Description The requested RAID configuration operation will not be allowed because the RAID controller is currently in Non-RAID mode.
retry the operation. 2) Cancel any pending operations on the RAID controller, and then retry the operation. Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR076 Message Enclosure configuration mode (Split/Unified) cannot be changed because there are already pending operations.
Detailed Description A Patrol Read State change operation cannot be performed if the Patrol Read Mode is not set to Manual. Recommended Response Action Change the Patrol Read Mode to Manual before performing a Patrol Read State change operation. Category Configuration Subcategory STOR = Storage Severity Severity 2 (Warning) LCD Message No LCD message display defined.
STOR079 Message The device does not support this operation or is in a state that does not allow this operation. Detailed Description The requested operation cannot be performed because it is either not supported by the device or the device was not in the right state to perform the operation. Recommended Response Action Make sure the device supports the requested operation. If the operation is supported, then make sure the server is turned on and retry the operation.
Server Administrator Trap ID Not Applicable STOR082 Message The operation cannot be stopped or cancelled because the operation is not currently running. Detailed Description The operation cannot be stopped or canceled because the operation is not currently running. Recommended Response Action Make sure the operation is running before attempting to cancel or stop the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR084 Message Unable to create the job because another job is currently running Detailed Description The requested job cannot be run because another job is currently running. Two options for running jobs on multiple storage controllers are: 1) Run the jobs on each controller individually. Wait for each job to complete before starting the configuration and job creation on the next controller.
Category Storage Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR090 Message Unable to create a virtual disk because an invalid value of span count value is entered for the RAID level selected.
Recommended Response Action Wait for the import process to complete before running any configuration operation. Category Storage Subcategory STOR = Storage Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR093 Message Unable to run the configuration operation because the controller is not available for the import process.
STOR094 Message The storage configuration operation is successfully completed and the change is in pending state. Detailed Description The storage configuration operation is successfully completed and the change is in pending state. Recommended Response Action To apply the configuration operation immediately, create a configuration job using the --realTime option. To apply the configuration after restarting the server, create a configuration job using the -r option.
Server Administrator Trap ID Not Applicable STOR096 Message Unable to create a virtual disk because the disk space size value entered for the virtual disk is less than the lower limit value (100 MB). Detailed Description A virtual disk cannot be created because the disk space size value entered for the virtual disk is less than the lower limit value (100 MB). Recommended Response Action Enter a value (the -size option) equal or higher than 100 MB, and then retry the operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR099 Message Arguments Unable to find the FQDD arg1 because an invalid FQDD is entered or an operation is pending on the specified FQDD. • arg1 = component FQDD Detailed Description The FQDD cannot be found because an invalid FQDD is entered or an operation is pending on the FQDD identified in the message.
Recommended Response Action See the storage hardware documentation for information on checking the cables. Check for problems with any enclosures attached to the system. Verify that the controller has a supported version of the driver and firmware. Rebooting the system may resolve this problem. Category Storage Subcategory STOR = Storage Severity Severity 2 (Warning) Trap/EventID 4178 LCD Message No LCD message display defined.
STOR2 Message Arguments SCSI sense data arg1 . • arg1 = args Detailed Description A SCSI device experienced an error, but may have recovered. Recommended Response Action No response action is required. Category Storage Subcategory STOR = Storage Severity Severity 3 (Informational) Trap/EventID 4179 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable STOR4 Message CEM Storage Management encountered internal error. Detailed Description There was a software problem in initializing the CEM storage management components. Storage inventory and monitoring will be affected. Recommended Response Action Reboot the system or iDRAC. If the problem is not resolved, contact technical support.
Recommended Response Action Identify and replace the failed components. To identify the failed component, select the Storage object and click the Health subtab. The controller status displayed on the Health subtab indicates whether a controller has a failed or degraded component. Click the controller that displays a Warning or Failed status. This action displays the controller Health subtab which displays the status of the individual controller components.
Server Administrator Trap ID Not Applicable STOR7 Message The storage management instrumentation is performing an inventory refresh operation. Detailed Description The storage monitoring instrumentation detected a burst of events from underlying storage controllers. To overcome this overload condition, all the outstanding events have been purged and a fresh inventory will be performed automatically. Recommended Response Action No response action is required.
SUP Event Messages 57 SUP001 Message Insufficient parameters provided. Detailed Description Insufficient Parameters provided for the WSMAN command. Recommended Response Action Make sure the parameters are correct and in the right number and format and retry the action. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP003 Message Invalid URI, target or reboot flag. Detailed Description One of the uniform resource input (URI) string, target or reboot flag parameters is missing or exceeds the prescribed length.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP006 Message Update package downloading - Delete failed. Detailed Description The DUP is being downloaded and the update cannot be deleted while the download is in progress Recommended Response Action Wait until the update package is downloaded and retry the action.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP009 Message Driver pack update in progress - Delete failed. Detailed Description Because of the size of the driver pack, the update process removes the older version of the driver pack from the system before installing the newer version. For that reason, the driver pack update cannot be deleted.
Subcategory SUP = FW Update Job Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0101 Message Unable to get firmware update status. Detailed Description Unable to get the update status. Recommended Response Action No response action is required.
Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0103 Message TFTP IP address is not reachable. Detailed Description The specified TFTP server is not reachable. Recommended Response Action Check if the TFTP server is alive.
Recommended Response Action Enter a source path < 64 characters. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0105 Message Invalid firmware image Detailed Description The firmware image provided by the user is not valid. Recommended Response Action Provide a valid firmware image.
Detailed Description There is no firmware image present at the specified path. Recommended Response Action Check if the firmware image is present at the specified path. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0107 Message File path too long.
SUP0108 Message A firmware update operation is already in progress. Detailed Description The firmware update is in progress and another update cannot be done. Recommended Response Action Wait for the update operation to conclude and then re-try. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SUP011 Message Invalid Job ID specified. Detailed Description The specified Job ID was not found in the job queue. Recommended Response Action Verify the job ID and retry the action. Retrieve all open jobs by issuing the GetAllJobs command. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0111 Message Timeout waiting for firmware update process to complete. Detailed Description Firmware Update time-out occurred. Recommended Response Action Re-try the firmware update process. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0113 Message TFTP firmware update is currently disabled. Detailed Description The cfgRhostsFwUpdateTftpEnable object must be set. Recommended Response Action Set the cfgRhostsFwUpdateTftpEnable object in cfgRemoteHosts group using config subcommand. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0115 Message A firmware update is currently in progress. Unable to reset the\nRAC at this time. Detailed Description The rac cannot be reset, while the firmware update is in progress. Recommended Response Action Wait for the firmware update to finish.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0117 Message Firmware rollback initiated successfully. \nThe iDRAC will now reset to complete the firmware rollback operation. Detailed Description Success message. Recommended Response Action No response action is required.
Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0119 Message Firmware rollback failed Detailed Description Success message. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0121 Message Arguments Firmware update in progress [ arg1 percent complete] • arg1 = Extent of completion Detailed Description Success message.
SUP0122 Message Firmware update completed successfully Detailed Description Success message. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0123 Message Firmware update completed successfully. The RAC is in the process of\nresetting.
Server Administrator Trap ID Not Applicable SUP0124 Message Firmware update is not currently in progress Detailed Description Success message. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0126 Message Firmware update in progress. Please wait... Detailed Description Success message. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0128 Message Ready for firmware update Detailed Description Success message. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP013 Message Update in progress - Delete failed. Detailed Description The update process is underway and cannot be deleted. Recommended Response Action Do not try to delete the job when the update process is underway.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0131 Message FTP firmware update has been initiated. This update process may take several minutes to complete. Detailed Description Success message. Recommended Response Action No response action is required.
Subcategory SUP = FW Update Job Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP015 Message Input parameters values should not be NULL. Detailed Description One of the parameters specified received a NULL value that prevented the action from completing. Recommended Response Action Correct the parameter value and retry the command.
Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP017 Message Invalid start time. Detailed Description The specified start time is invalid. Recommended Response Action Start Time should be in the form YYYYMMDDHHMMSS. Or it should be TIME_NOW to specify an immediate update or reboot.
Recommended Response Action Until Time should be in the form YYYYMMDDHHMMSS. Verify the specified until time and retry the action. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP019 Message Lifecycle Controller is not enabled.
SUP020 Message The specified job was deleted Detailed Description The specified job was successfully deleted from the job queue. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SUP022 Message Job store has reached the maximum storage limit. Detailed Description JobStore file has exceeded the size limit. Delete all unneeded JobIDs from the job store. Recommended Response Action New JobId cannot be stored. Manually delete the failed jobs and retry the operation. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP024 Message InstanceID value provided for the update operation is invalid Detailed Description The InstanceID value provided for update operation is invalid. Recommended Response Action Enumerate inventory, copy the InstanceID value and provide that value for the update operation Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP026 Message Arguments The input value entered for the parameter arg1 is invalid. • arg1 = parameter Detailed Description The value entered for the parameter identified in the message is invalid. Recommended Response Action Correct the specified input value and retry the operation.
Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP028 Message The GetRepoBasedUpdateList method did not complete successfully. Detailed Description The GetRepoBasedUpdateList method was not successfully executed because the InstallFromRepo method was not executed first.
Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP030 Message Proxy IP and User Credential pare valid only if the ProxySupport parameter is TRUE.
Detailed Description The catalog file is not in the supported XML format, or the catalog file is corrupted. Recommended Response Action Do one of the following: 1) If the catalog file is customized, recreate the file using Repository Manager, and retry the operation. 2) Update the catalog file from the service providers FTP server and retry the operation. 3) Update the catalog file from the System Update Utility media or from the System Build Update Utility media and retry the operation.
Server Administrator Trap ID Not Applicable SUP0503 Message Unable to retrieve the system ID. Detailed Description Unable to retrieve the system ID from BIOS. Recommended Response Action Retry the operation. If the problem persists, do one of the following: 1) Reboot the system and retry the operation. 2) Update the BIOS firmware to the latest version and retry the operation. If the problem continues to persist contact the service provider.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0505 Message Corrupt catalog file. Detailed Description The catalog file in the selected repository is corrupt. Recommended Response Action Select a repository with a valid catalog file, and retry the operation. Category Updates Subcategory SUP = FW Update Job Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0507 Message Unable to download the Update Packages from the FTP server. Detailed Description The FTP server setting details are incorrect. Recommended Response Action Enter the correct FTP server settings details, and retry the operation. Category Updates Subcategory SUP = FW Update Job Severity Severity 1 (Critical) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0513 Message Unable to access the Update Package. Detailed Description The specified filename path to the Update Package is incorrect. Recommended Response Action Enter the correct file path where the Update Package is located and retry the operation. If the problem persists, reboot the system and retry the operation.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0515 Message Unable to authenticate the Update Package signature. Detailed Description Lifecycle Controller was unable to authenticate the Update Package digital signature. The Update Package will not be applied unless it has a valid digital signature.
Recommended Response Action No response action required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0517 Message Arguments Unable to update the arg1 firmware to version arg2 .
SUP0518 Message Arguments Successfully updated the arg1 firmware to version arg2 . • arg1 = component • arg2 = version Detailed Description The specified firmware for the component was successfully updated. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0520 Message Arguments Unable to update the arg1 firmware to version arg2 . • arg1 = component • arg2 = version Detailed Description The firmware update operation for the component did not complete due to an internal error. Recommended Response Action Retry the operation. If the problem persists, download the latest Update Package from your service provider and retry the operation.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0525 Message Unable to verify the digital signature of the Update Package. Detailed Description Unable to verify the digital signature of the Update Package. Recommended Response Action Download the latest Update Package from your service provider and retry the operation.
Subcategory SUP = FW Update Job Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0527 Message The Update Package is not supported for this system. Detailed Description The Update Package does not have this system in the supported platform list.
Category Updates Subcategory SUP = FW Update Job Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0529 Message Unable to access repository. Detailed Description The selected USB drive is disconnected. Recommended Response Action Make sure the USB drive is connected and retry the operation.
Recommended Response Action Retry the operation with the correct catalog repository path. Category Updates Subcategory SUP = FW Update Job Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0531 Message Unable to install the Update Packages. Detailed Description The repository location is invalid or the repository does not contain the Update Packages.
Detailed Description The repository contains corrupt Update Packages. Recommended Response Action Enter another repository location that contains the desired Update Packages and retry the operation. Category Updates Subcategory SUP = FW Update Job Severity Severity 1 (Critical) LCD Message No LCD message display defined.
SUP0534 Message Unable to locate the catalog file. Detailed Description The catalog file cannot be found in the specified location. Recommended Response Action Specify the correct repository location and retry the operation. Category Updates Subcategory SUP = FW Update Job Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SUP0536 Message Arguments Successfully updated arg1 . • arg1 = component and version Detailed Description Component firmware update was successful. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP0538 Message Arguments Unable to update arg1 . • arg1 = component and version Detailed Description Unable to update firmware due to one the following: 1) Update Package is not supported. 2) Trusted Platform Module feature is enabled in BIOS settings. Recommended Response Action Retry the operation.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP1901 Message Firmware update initializing. Detailed Description Firmware update initializing. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP1903 Message Firmware update verify image headers. Detailed Description Firmware update verify image headers. Recommended Response Action No response action is required.
Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP1905 Message Firmware update programming flash. Detailed Description Firmware update programming flash. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP1907 Message Firmware update failed. Detailed Description Firmware update failed. Recommended Response Action Reacquire the image from the original source and retry the operation.
Detailed Description Firmware update failed checksum. Recommended Response Action Reacquire the image from the original source and retry the operation. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP1909 Message Firmware update failed image download.
SUP1910 Message Firmware update is not pending. Detailed Description Firmware update is not pending. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SUP1911 Message Firmware update initialization complete.
Server Administrator Trap ID Not Applicable SUP1912 Message Firmware update RAC recover successful. Detailed Description Firmware update RAC recover successful. Recommended Response Action No response action is required. Category Updates Subcategory SUP = FW Update Job Severity Severity 3 (Informational) LCD Message No LCD message display defined.
SWC Event Messages 58 SW0725 Message iDRAC7 communication failure. Detailed Description iDRAC7 is busy and does not respond to iDRAC7 configuratorIPMI requests. Recommended Response Action Try AC power cycling the server or upgrade the iDRAC firmware. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0002 Message Unable to set Part Replacement policies. Detailed Description The Part Replacement policy configuration operation encountered an unexpected error while communicating with iDRAC. Recommended Response Action Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0004 Message Unable to add a work note to the Lifecycle Log. Detailed Description The operation to add a work note to the Lifecycle Log encountered an unexpected error while communicating with iDRAC. Recommended Response Action Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0006 Message Unable to display the As Shipped hardware inventory. Detailed Description The view As Shipped hardware inventory operation encountered an unexpected error while communicating with iDRAC. Recommended Response Action Retry the operation.
Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0008 Message Unable to write the As Shipped hardware inventory to the specified destination.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0012 Message Unable to retrieve the front panel security settings. Detailed Description The operation to retrieve the front panel security settings encountered an unexpected error while communicating with iDRAC.
Recommended Response Action Retry the operation. If the problem persists: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds. 3) Reconnect the power cord, turn on the system, and retry the operation. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Detailed Description The operating system driver pack is missing or not accessible. Recommended Response Action Update the system with the latest Lifecycle Controller OS Driver Pack. Obtain the OS Driver Pack from the service provider. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
SWC0017 Message Unable to retrieve the drivers for the selected operating system. Detailed Description An unrecoverable error occurred while retireving the drivers. Recommended Response Action Exit the OS Deployment wizard and retry the operation. If the problem persists, exit Lifecycle Controller and perform an AC power cycle. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC0019 Message The Test Network Connection operation completed with errors. Detailed Description The Test Network Connection ping test timed-out. The network cable is disconnected or the network is not configured correctly. Recommended Response Action Check the network cable connection and network configuration settings, then retry the operation. If the problem persists, reconfigure the network settings and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0024 Message The Test Network Connection ping test timed-out. Detailed Description The Test Network Connection ping test timed-out. The network cable is disconnected or the network is not configured correctly. Recommended Response Action Check the network cable connection and network configuration settings, then retry the operation.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0026 Message Unable to retrieve status of backup Server Profile operation. Detailed Description Status of backup Server Profile operation could not be retrieved because an unrecoverable error occurred while communicating with iDRAC. Recommended Response Action Reset iDRAC and retry the operation.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0028 Message The backup Server Profile operation did not successfully complete. Detailed Description iDRAC is unable to complete the backup Server Profile operation because an unrecoverable error occurred. Recommended Response Action Reset iDRAC and retry the operation.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0030 Message Unable to complete the backup Server Profile backup operation. Detailed Description iDRAC is unable to complete the backup Server Profile operation. Recommended Response Action Reset iDRAC and retry the operation.
Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0032 Message Successfully exported the Server Configuration Profile image file to the USB drive. Detailed Description Exporting the Server Configruation Profile image file to the USB drive was successful. Recommended Response Action No response action is required.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0034 Message Unable to export the file to the network share. Detailed Description Lifecycle Controller is unable to export the file to the network share because it has insufficient free space.
Recommended Response Action Assign a service tag to the system and retry the operation. To assign the service tag, contact your service provider. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0036 Message Unable to launch hardware diagnostics.
Detailed Description Lifecycle Controller is unable to export the file to the network share because the destination folder is not present or inaccessible. Recommended Response Action Make sure that the destination folder is present and accessible, then retry the operation. If the problem persists, check network settings and retry the operation. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
SWC0039 Message Unable to find the backup Server Configuration Profile image. Detailed Description The backup Server Configuration Profile image partition is not present in the vFlash SD card. Recommended Response Action A backup Server Configuration Profile is required to import or export a Server Profile. Perform the backup operation and retry import or export operation.
Server Administrator Trap ID Not Applicable SWC0041 Message Unable to copy the backup Server Configuration Profile. Detailed Description The specified source file location is incorrect. Recommended Response Action Make sure that the specified source file location is correct and retry the operation. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0043 Message Import Server Profile operation completed with errors. Detailed Description The Import Server Profile operation has completed with errors. For more information, see the Lifecycle Log. Recommended Response Action Exit the Import Server Profile wizard and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0045 Message Unable to complete the Import operation. Detailed Description The Import operation did not successfully complete. For more information, see the Lifecycle Log. Recommended Response Action Exit the Import Server Profile wizard and retry the operation. If the problem persists, do the following: 1) Turn off the system and disconnect the power cord. 2) Wait for five seconds.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0047 Message Incorrect backup Server Configuration Profile file passphrase provided. Detailed Description The passphrase specified is not correct. Recommended Response Action Enter the valid passphrase and retry the operation.
Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0049 Message Unable to continue the Import operation. Detailed Description The Import operation cannot continue because backup image file is not present on the vFlash SD card, the image is invalid, or the entered passphrase is incorrect.
Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0051 Message Unable to retrieve iDRAC license information. Detailed Description Unable to retreive license information due to an iDRAC communication error. Recommended Response Action Exit Lifecycle Controller and retry the operation.
Recommended Response Action Exit the OS Deployment wizard and update the system with the latest operating system driver packs available from the service provider and retry the operation. For more information, see the Lifecycle Controller users guide. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Detailed Description There was an internal error while saving the settings. Recommended Response Action Retry the operation. If the problem persists, reboot the system or update the Lifecycle Controller firmware to the latest version and retry the operation. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
SWC0056 Message Unable to export the file to the USB drive. Detailed Description Unable to export the file to the USB drive because it does not have the specified folder, does not have enough free space, or is read-only. Recommended Response Action Make sure that the USB drive contains the folder specified, has enough free space, or is not read-only. If the problem persists, reboot the system and retry the operation.
Server Administrator Trap ID Not Applicable SWC0058 Message Unable to complete the operation. Detailed Description An internal processing error occurred. Recommended Response Action Reboot the system and retry the operation. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0060 Message Unable to complete the operation. Detailed Description One or more vFlash partitions are attached. Recommended Response Action Use iDRAC Web interface to detach the vFlash partitions and retry the operation. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0062 Message Unable to export Lifecycle Log. Detailed Description The destination folder is not present, the destination is full or write-protected. Recommended Response Action Verify the following and retry the operation: 1) Destination folder is present. 2) Destination has enough free space. 3) Destination is not write-protected.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0064 Message Unable to mount the network share. Detailed Description The details provided to access the network share are incorrect. Recommended Response Action Enter the correct network share details, and retry the operation.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0066 Message Unable to connect to the Network Share. Detailed Description Unable to connect to the Network Share due to one of the following: 1) Login credentials entered are incorrect. 2) Network is inaccessible. 3) System IP address conflicts with another system on the network.
Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0068 Message Unable to retrieve the boot mode settings from BIOS. Detailed Description The BIOS boot mode settings could not be retrieved because of an internal issue. Recommended Response Action Exit the OS Deployment wizard and retry the operation.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0070 Message The Tech Support Report is successfully exported to the USB drive. Detailed Description The Tech Support Report is successfully exported to the USB drive. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0072 Message Unable to export the Tech Support Report to destination folder. Detailed Description Tech Support Report cannot be exported to the destination folder.
Detailed Description The Repurpose or Retire system operation cannot be successfully started because the current version of iDRAC firmware does not support the operation. Recommended Response Action Update iDRAC firmware to the latest version and retry the operation. If the issue persists, contact your service provider. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
SWC0075 Message Unable to perform RAID operations because the selected controller is in HBA mode. Detailed Description Unable to perform RAID operations because the selected controller is in HBA mode. Recommended Response Action Do one of the following: 1) Retry the operation using other controllers that support RAID operations and are not in HBA mode. 2) Change the mode of the controller from HBA mode to RAID mode and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0077 Message Unable to initiate the Repurpose or Retire System operation. Detailed Description iDRAC is unable to initiate the Repurpose or Retire System operation because the iDRAC is not responding or another operation is in progress. Recommended Response Action Retry the operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0102 Message The -m option is not supported by the interface being used. Detailed Description The option requested is not available on the interface being used. Recommended Response Action Refer to the help to get the list of options valid for the interface.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0104 Message The -R option is not valid for the specified log. Detailed Description The specified log does not take in the -r option. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0106 Message The -u option is not supported on the current RAC configuration. Detailed Description The specified option is not supported on the RAC. Recommended Response Action No response action is required.
Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0108 Message The service tag is not currently populated. Detailed Description The Service Tag string is empty. Recommended Response Action No response action is required.
Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0110 Message No build information is currently available. Detailed Description The build information is not available for racdump. Recommended Response Action No response action is required.
Recommended Response Action Refer the help for serveraction subcommand, and enter a valid option. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0112 Message Timeout while waiting for server to perform requested power action.
Detailed Description The syntax of the setniccfg command is invalid. Recommended Response Action Refer the help text for setniccfg subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0114 Message The -o option cannot be used with any other options.
SWC0115 Message The -s option cannot be used with any other options. Detailed Description The syntax of the setniccfg command is invalid. Recommended Response Action Refer the help text for setniccfg subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC0117 Message Invalid syntax. Both -f and -t must be specified. Detailed Description Invalid parameters passed to the function. Recommended Response Action Refer the help text for sslcertdownload subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0119 Message Invalid certificate type specified with -t option. Detailed Description The syntax of the sslcertview command is invalid. Recommended Response Action Refer the help text for sslcertview subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0121 Message Invalid syntax. User index (-i) must be specified. Detailed Description The syntax of the sslcertview command is invalid. Recommended Response Action Refer the help text for sslcertview subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0123 Message The -s option is not valid with any other options. Detailed Description The syntax of the sslcsrgen command is invalid. Recommended Response Action Refer the help text for sslcsrgen subcommand.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0125 Message Unable to generate CSR. Detailed Description The CSR file could not be generated. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0127 Message Unable to open file for writing. Detailed Description The file may be write protected and hence could not be edited. Recommended Response Action Check if the file is write protected.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0129 Message Unable to send test email. Please make sure that your email alerts\nhave been configured correctly and connectivity to \nthe SMTP server exists.
Recommended Response Action Set cfgIpmiPetAlertEnable in cfgIpmiPet group using config subcommand for the corresponding index. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0131 Message Trap destination address must be configured.
Detailed Description Either the destination Ip address is not reachable or the required values are not configured. Recommended Response Action Check for the connectivity to the configured Ip address. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
SWC0134 Message The RAC log was cleared successfully Detailed Description Success message. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0135 Message The SEL was cleared successfully Detailed Description Success message.
Server Administrator Trap ID Not Applicable SWC0136 Message Object value modified successfully Detailed Description Success message. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0138 Message Coredump request completed successfully Detailed Description Success message. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0140 Message RAC reset operation initiated successfully. It may take up to a minute \nfor the RAC to come back online again. Detailed Description Success message. Recommended Response Action No response action is required.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0142 Message Certificate successfully uploaded to the RAC. Detailed Description Success message. Recommended Response Action No response action is required. Category System Health Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0144 Message Certificate successfully uploaded to the RAC. The RAC will now reset\nto enable the new certificate and may be offline temporarily. Detailed Description Success message. Recommended Response Action No response action is required.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0146 Message Last ASR screen was cleared successfully Detailed Description Success message. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0148 Message Test email sent successfully Detailed Description Success message. Recommended Response Action No response action is required.
Detailed Description The requested SNMP test trap alert was successfully sent. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0150 Message Object value is valid Detailed Description Success message.
SWC0151 Message RAC configuration saved to file successfully Detailed Description Success message. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC0153 Message RAC configuration file is valid Detailed Description Success message. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0154 Message Generating CSR. Please wait...
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0155 Message CSR generated and downloaded from RAC successfully Detailed Description Success message. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0157 Message User certificate successfully uploaded to the RAC. Detailed Description Success message. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0159 Message Kerberos Keytab successfully uploaded to the RAC. Detailed Description Success message. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0161 Message PK SSH Authentication operation completed successfully. Detailed Description Success message. Recommended Response Action No response action is required.
Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0202 Message Key successfully deleted Detailed Description Help Text. Recommended Response Action No response action is required.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0204 Message Key text successfully uploaded Detailed Description Help Text. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0206 Message View user certificate information Detailed Description Help Text. Recommended Response Action No response action is required.
Detailed Description Help Text. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0208 Message Disconnect Virtual Media connections Detailed Description Help Text. Recommended Response Action No response action is required.
SWC0209 Message Connect or disconnect image server connections Detailed Description Help Text. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0210 Message Display NIC teaming information Detailed Description Help Text.
Server Administrator Trap ID Not Applicable SWC0211 Message Perform vFlash operations Detailed Description Help Text. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0213 Message Disable the Virtual Console from a local Console Detailed Description Help Text. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0215 Message Disable Remote File Started.Please check status using -s option to know Remote File Share is ENABLED or DISABLED. Detailed Description The process to disable the file share has started. Use the -s option to know more about the status. Recommended Response Action If required check the status using the -s option.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0217 Message The -c option requires -u to also be specifed. Detailed Description The syntax of the command is incorrect. Recommended Response Action Refer to the help for remote image command. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0219 Message The -p option requires -c to also be specifed. Detailed Description The syntax of the command is incorrect. Recommended Response Action Refer to the help for remote image command.
Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0221 Message The -l option requires -c to also be specifed. Detailed Description The syntax of the command is incorrect. Recommended Response Action Refer to the help for remote image command.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0223 Message Invalid syntax. The -d option is not valid with -p. Detailed Description The syntax of the command is incorrect. Recommended Response Action Refer to the help for remote image command.
Recommended Response Action Refer to the help for remote image command. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0225 Message Invalid syntax. The -d option is not valid with -l. Detailed Description The syntax of the command is incorrect.
Detailed Description The Remote/Firmware racadm did not find any AD/LDAP certificate at specified path. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0227 Message Partition label exceeds maximum limit of 6 alphanumeric characters.
SWC0228 Message Partition label must be an alphanumeric character string. Detailed Description Invalid values passed to the function. Recommended Response Action Enter a shorter Partition label. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC0230 Message vFlash not enabled. Detailed Description vFlash is not enabled. This may be because the user does not have enough privileges. Recommended Response Action Enable vFlash and re-try. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0232 Message Remote RACADM commands are not supported on this iDRAC. To upgrade your iDRAC version, contact your service provider. Detailed Description Remote RACADM commands are not supported on the current iDRAC. Recommended Response Action If remote RACADM is a necessity, upgrade the iDRAC version.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0234 Message Remote host is not reachable or connection is interrupted. Detailed Description The remote host specified for the ftp update is not reachable. Recommended Response Action Check the connectivity between iDRAC and the remote host used for the ftp update.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0236 Message Key successfully deleted. Detailed Description The specified public key was deleted from iDRAC. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0238 Message Key is too long. Detailed Description The key specified by the public key is too long. Recommended Response Action Request for a valid public key from the system and re-try the command.
Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0240 Message The IPv6 DNS Server IP address is not allowed to be configured if IPv6 DNS Server DHCP (cfgIPv6DNSServersFromDHCP6) is enabled Detailed Description The requested object is auto-assigned if DNS Server DHCP is enabled, and hence cannot be configured.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0242 Message A required license is missing or expired. Obtain an appropriate license and try again, or contact your service provider for additional details. Detailed Description The license is missing or expired.
Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0244 Message Invalid Fully Qualified Device Descriptor (FQDD). Detailed Description The specified Fully Qualified Device Descriptor (FQDDs) system component name is invalid.
Detailed Description Local configuration using RACADM is disabled. This limits local configuration privileges such as resetting object values. Recommended Response Action Within group cfgRacTuning set the property cfgRacTuneLocalConfigDisable to 0. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
SWC0247 Message Invalid subcommand specified. Detailed Description An invalid subcommand was entered. Recommended Response Action Refer the list of subcommands. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0248 Message Invalid command syntax.
Server Administrator Trap ID Not Applicable SWC0249 Message Arguments Invalid syntax. The requestsed subcommand requires -i arg1 to be specified. • arg1 = index Detailed Description The specified parameter needs to be given with its legal value. Recommended Response Action Enter the proper index preceeded by -i. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0251 Message Arguments Invalid index value. Only index values arg1 - arg2 are permitted. • arg1 = number • arg2 = number Detailed Description The value of specified parameter is invalid. Recommended Response Action Enter the index value as specified by the message.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0253 Message Unable to allocate memory needed to perform operation. Detailed Description Unable to allocate memory to perform the operation, see the inserted comment. Recommended Response Action Power Cycle the system and re-enter the command.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0255 Message Unable to open file. Detailed Description Unable to open the specified file. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0257 Message Invalid syntax. Too many options specified. Detailed Description Invalid number of arguments were passed to the command.
Detailed Description Insuffcient resources to execute the command. Recommended Response Action Power Cycle the system and re-enter the command. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0259 Message Invalid group specified.
SWC0260 Message Invalid object specified. Detailed Description The value of specified parameter is invalid. Recommended Response Action Refer the list of objects in the corresponding group. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC0262 Message Unable to perform operation. Please make sure RAC controller and \nappropriate IPMI drivers are installed. Detailed Description The IPMI drivers or the RAC contorller may not be installed. Recommended Response Action Check if the required modules are installed. Category Configuration Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0264 Message Resource currently in use by another process. Please retry again later. Detailed Description The resources required for the execution are in use by another process Recommended Response Action Wait for the process to release the resources and try again. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0266 Message Unable to perform the requested operation. Make sure SD card is inserted. Detailed Description The SD card may not be inserted/inserted properly. Recommended Response Action Ensure that the SD card is inserted in the server. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0268 Message There is no ASR screen currently available to clear Detailed Description The ASR screen is already cleared. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0270 Message Unable to clear the SEL. \nPossible reason may be that Local Configuration using RACADM is disabled. Detailed Description Local Configuration using RACADM may be disabled. Recommended Response Action Check if the Local Configuration using RACADM is disabled and enable it through GUI.
Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0272 Message Invalid syntax. The -g option is only valid with -o, -i, and -c. Detailed Description The syntax for the config command is invalid. Recommended Response Action Refer to the help text for the config subcommand.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0274 Message Invalid syntax. An object value must be specified. Detailed Description The value of specified parameter is invalid. Recommended Response Action Enter the same command with a legal value to the object.
Recommended Response Action Refer to the help text for the config subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0276 Message Invalid syntax. The -p option is only valid with -f. Detailed Description The syntax for the config command is invalid.
Detailed Description The syntax for the config command is invalid. Recommended Response Action Refer to the help text for the config subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0278 Message Invalid group or object specified.
SWC0279 Message The specified group is not indexed and does not support -i. Detailed Description The group is not indexed and does not require an index to be specified. Recommended Response Action Enter the command without the index. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC0281 Message The specified object is READ ONLY and cannot be modified. Detailed Description The value being modified is READ only. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0283 Message The specified object value is not valid. Detailed Description The value given for the object is not valid. Recommended Response Action Enter a valid value for the corresponding object. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0285 Message Object value is invalid. Detailed Description The value given for the object is not valid. Recommended Response Action Enter a valid value for the corresponding object. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0287 Message Invalid entry in configuration file. Detailed Description The value of a parameter in the config file is invalid. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Recommended Response Action Configure the object specified in the message in specified group, before performing a config to file action. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0289 Message Arguments Invalid value in config file. Group: arg1 , Object: arg2 , Value: \" arg3 \", Line [
SWC0290 Message Arguments Failed to configure object. Group: arg1 , Object : arg2 • arg1 = Group Name • arg2 = Object Name Detailed Description Failed to configure the object specified in the error message. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0292 Message Arguments The specified object at index arg1 does not exist. • arg1 = index number Detailed Description The queried object does not exist at the specified index. Recommended Response Action Check for the objects available at the specified index and re-try.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0294 Message Invalid group name specified. Detailed Description The group name specified is incorrect. Recommended Response Action Refer to the list of groups available and choose the correct one. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0296 Message The specified value is not allowed to be configured if the user name \nor password is blank. Detailed Description Either the password field or the username field is empty. Recommended Response Action Enter the command with the username and password.
Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0298 Message The specified object value cannot be configured if local configuration is disabled or smart card logon is enabled. If smart card logon is enabled, serial, SSH, telnet and IPMIoverLAN is disabled by force and cannot be enabled.
Recommended Response Action Specify a valid Email address. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0300 Message There is no coredump currently available. Detailed Description There is no coredump available to display. Recommended Response Action No response action is required.
Detailed Description The IP address provided is not valid. Recommended Response Action Specify a valid IP Address. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0302 Message The -s option is not valid with any other option. Detailed Description The syntax of the fwupdate command is invalid.
SWC0303 Message The -r option is not valid with any other option. Detailed Description The syntax of the fwupdate command is invalid. Recommended Response Action Refer the help text for fwupdate subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC0305 Message The -p option requires -u to also be specifed. Detailed Description The syntax of the fwupdate command is invalid. Recommended Response Action Refer the help text for fwupdate subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0307 Message The -d option requires -p or -g to also be specifed. Detailed Description The syntax of the fwupdate command is invalid. Recommended Response Action Refer the help text for fwupdate subcommand. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0309 Message The -p option is not supported with the interface being used. Detailed Description The platform does not support the specified functionality of fwupdate. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0311 Message Invalid syntax. The -g option is only valid with -i and -o options. Detailed Description The syntax of the getconfig command is invalid. Recommended Response Action Refer the help text for getconfig subcommand.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0313 Message Invalid syntax. The -h option is not valid with any other options. Detailed Description The syntax of the getconfig command is invalid. Recommended Response Action Refer the help text for getconfig subcommand.
Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0315 Message Failed to get object value. Detailed Description The getconfig subcommand failed to get the object value. Recommended Response Action No response action is required.
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0317 Message The number of records to display must be greater than zero. Detailed Description The value for -c must be greater than zero. Recommended Response Action Enter a value greater than zero, for the option -c.
Recommended Response Action Enter a value greater than zero, for the option -s. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0319 Message The -i option is not valid with any other options. Detailed Description The syntax for the getraclog command is invalid.
Detailed Description Racadm tool failed to get the total number of records. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0321 Message Unable to open the log for reading.
SWC0322 Message Starting record specified exceeds number of records available. Detailed Description The starting record value has to be lesser than the number of records available. Recommended Response Action Get the number of records available, and then run the command. If the command is gettracelog, try executing the command again. Category Configuration Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC0324 Message There are no records available to display. Detailed Description There are no records to display. This might be a result of the log being cleared. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0700 Message iDRAC is not ready. The configuration values cannot be accessed. Please retry after a few minutes. Detailed Description iDRAC7 is not ready or is busy and is not responding to iDRAC7 Settings IPMI requests. Recommended Response Action Turn off the system, Remove AC. Wait for 5 seconds. Connect AC. Turn it on.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0702 Message Power capping is disabled. Detailed Description Power capping is disabled and sets recommended limits for the system. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0722 Message Error occurred while resetting to defaults. The reset command was not accepted. Detailed Description iDRAC is processing a previous reset to default command. Recommended Response Action Retry after a few minutes.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC0724 Message Error occurred while Resetting to defaults due to a timeout. Detailed Description Resetting to defaults did not complete within the maximum process alloted time. Recommended Response Action Retry after a few minutes.
Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1905 Message RAC Virtual Console configuration has been changed. Detailed Description RAC Virtual Console configuration has been changed. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1910 Message Arguments User ID arg1 User Name has been changed. • arg1 = username Detailed Description User ID Name has been changed.
SWC1911 Message Arguments User ID arg1 User Password has been changed. • arg1 = username Detailed Description User ID Password has been changed. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1913 Message Network Time Protocol configuration is enabled. Detailed Description Network Time Protocol configuration is enabled. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1915 Message iDRAC time zone has changed. Detailed Description iDRAC time zone has changed. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1917 Message HTTPS redirection is disabled. Detailed Description HTTP to HTTPS redirection is disabled. Any iDRAC connection made over the HTTP port (default port number 80) will no longer be redirected to the secure HTTPS port (default port number 443).
Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1920 Message The Chassis Management at Server Mode is enabled. Detailed Description The Chassis Management at Server Mode is enabled. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Audit Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1922 Message Arguments User arg1 has successfully modified the server configuration by using Quick Sync.
SWC1923 Message Unable to modify the server configuration by using Quick Sync because invalid credentials are entered. Detailed Description The server configuration cannot be modified by using Quick Sync because invalid credentials are entered. Recommended Response Action Make sure that correct user name and password are entered, and then retry the operation. Category Audit Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC1925 Message The iDRAC Quick Sync access feature is set to the Disabled mode. Detailed Description The iDRAC Quick Sync access feature is set to the Disabled mode. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1927 Message The iDRAC Quick Sync access feature is set to the read-only mode. Detailed Description The iDRAC Quick Sync access feature is set to the read-only mode. Recommended Response Action No response action is required. Category Configuration Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1929 Message Arguments The iDRAC Quick Sync inactivity timeout value is set to arg1 . • arg1 = timeout period Detailed Description The iDRAC Quick Sync inactivity timeout value is set to the value identified in the message. Recommended Response Action No response action is required.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC1931 Message The iDRAC Quick Sync inactivity timeout configuration is disabled. Detailed Description The iDRAC Quick Sync inactivity timeout configuration is disabled. The iDRAC Quick Sync feature will remain available after pressing the activate button.
Recommended Response Action Check firmware versions of iDRAC and CMC. Update to latest version. Category System Health Subcategory SWC = Software Config Severity Severity 2 (Warning) Trap/EventID 2338 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC4005 Message Arguments A firmware or software incompatibility was corrected between iDRAC in slot arg1 and CMC.
SWC4006 Message Arguments A firmware or software incompatibility detected between system BIOS in slot arg1 and CMC. • arg1 = number Detailed Description FlexAddress is not implemented in one of the versions of firmware. Please update the firmware. Recommended Response Action Check firmware versions of BIOS and CMC. Update to latest version. Category System Health Subcategory SWC = Software Config Severity Severity 2 (Warning) Trap/EventID 2338 LCD Message No LCD message display defined.
Trap/EventID 2339 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC4008 Message A firmware or software incompatibility detected between CMC 1 and CMC 2. Detailed Description FlexAddress is not implemented in one of the versions of firmware. Please update the firmware. Recommended Response Action Check firmware versions. Update CMC 1 and CMC 2 firmware to match.
Category System Health Subcategory SWC = Software Config Severity Severity 3 (Informational) Trap/EventID 2339 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC4010 Message Arguments arg1 arg2 in Server- arg3 requires a version of Chassis Management Controller (CMC) firmware 5.0 or later for using the NParEP (ARI mode) functions.
SWC4011 Message Arguments A firmware or software incompatibility is automatically corrected between the arg1 arg2 in Server- arg3 and the Chassis Management Controller (CMC). • arg1 = network device name • arg2 = network device location • arg3 = server location Detailed Description A firmware or software incompatibility was automatically corrected between the network device in the Server identified in the message and the Chassis Management Controller (CMC).
Recommended Response Action Update the firmware or software of the components identified in the message. For information about the identified components, see the product documentation available at the service provider support site. Category System Health Subcategory SWC = Software Config Severity Severity 1 (Critical) Trap/EventID 2337 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SWC5000 Message Arguments arg1 upgrade was successful. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory SWC = Software Config Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC5002 Message Arguments arg1 upgrade was successful but encountered minor errors. • arg1 = name Detailed Description None Recommended Response Action Check system logs for minor errors. Category System Health Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Category System Health Subcategory SWC = Software Config Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SWC5004 Message System Controller (SC) has restarted functioning. Detailed Description System Controller (SC) has started functioning again because either a server health issue is resolved or SC has completed a firmware update process.
Recommended Response Action Retry the SC firmware update operation. If the issue persists, try updating by using a different firmware update file. Category Updates Subcategory SWC = Software Config Severity Severity 1 (Critical) LCD Message No LCD message display defined.
SWU Event Messages 59 SWU001 Message The backplane firmware update completed successfully. Detailed Description The expander or storage enclosure processor firmware update completed successfully. Recommended Response Action No response action is required. Category Storage Subcategory SWU = Software Change Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable 1867
SYS Event Messages 60 SYS001 Message The operation was successful. Detailed Description The operation requested successfully completed. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS003 Message Arguments Missing parameters: arg1 . • arg1 = parameter names Detailed Description One or more required parameters needed for the operation are missing. Recommended Response Action Refer to the Lifecycle Controller Remote Services documentation and retry the operation with the required parameters.
Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS005 Message AttributeName array and AttributeValue array element count mismatch. Detailed Description The AttributeName input array and AttributeValue input array do not have the same number of elements.
Recommended Response Action Refer to the Lifecycle Controller Remote Services documentation for the specific attribute behavior. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS007 Message Arguments Input out of range for arg1 .
SYS008 Message Arguments Invalid boolean in value for attribute: arg1 . • arg1 = attribute name Detailed Description The input value for the specified attribute is not a valid boolean value for the attribute. Recommended Response Action Refer to the Lifecycle Controller-Remote Services documentation and provide a valid boolean value for the specified attribute. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS010 Message Arguments Invalid character in value for attribute: arg1 • arg1 = attribute name Detailed Description The input value for the specified attribute is not valid. Recommended Response Action Refer to Lifecycle Controller-Remote Services documentation and provide valid attribute value for the specified attribute.
Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS012 Message User privileges are not sufficient to perform operation. Detailed Description The user credentials provided do not have appropriate privileges to perform the operation requested.
Recommended Response Action For more information, see Lifecycle Controller-Remote Services documentation. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
SYS015 Message Job created successfully. Detailed Description The requested job has been created. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SYS017 Message Job did not complete successfully. Detailed Description The job did not complete successfully. Recommended Response Action Verify the reason for the unsuccessful completion of the job by inspecting the Lifecycle Log entries related to the job. Correct the underlying cause of the unsuccessful completion and retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS019 Message Required dependency input not found. Detailed Description The input is missing a required dependency necessary for the operation. Recommended Response Action Provide the required dependency and retry. For more information, see Lifecycle Controller Remote Services documentation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS021 Message Arguments Unable to set the value for arg1 • arg1 = attribute name Detailed Description The operation did not complete successfully because of incorrect parameters or internal firmware issues. Recommended Response Action Retry the operation. If the issue persists, do one of the following: 1) verify the value being set is correct, 2) reset the iDRAC.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS023 Message No configuration changes pending. Detailed Description There are no pending values to change. Recommended Response Action Ensure there are pending values for the attributes that need to be set and retry the operation.
Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS025 Message Unable to delete pending configuration. Detailed Description There are no pending configurations to be deleted. Recommended Response Action No response action is required.
Recommended Response Action Remove the unsupported parameter and retry the operation. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS030 Message Collecting component configuration information. Detailed Description Collecting the data required for component configuration.
Detailed Description The configuration is being applied to a component. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS032 Message Staged component configuration is complete.
SYS033 Message Staged component configuration completed with errors. Detailed Description The staged component configuration update performed in the UEFI environment on the host system has completed, but there were errors. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SYS035 Message Arguments Some configuration values were not applied to: arg1 • arg1 = device name Detailed Description The component configuration operation was completed, however some of the configuration values were not successfully applied. Recommended Response Action Retrieve and view configuration operation results in the Lifecycle Log. For more information to retrieve the configuration results see the Lifecycle Controller Remote Services Users Guide.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS037 Message Component update initialization failure. Detailed Description Operation validation is unsuccessful. The command, target and operation data are all validated before an update is performed. If any of them are missing or incorrect the operation does not complete successfully.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS039 Message Verification of requested configuration changes failed. Detailed Description The requested configuration changes have not passed the component specific verification checks, and therefore the changes will not be applied.
Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS041 Message Unable to apply some component configuration values. Detailed Description The configuration update is complete, however all of the values were not correctly applied. Recommended Response Action Check the Lifecycle Log for the values that were not set.
Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS043 Message Successfully exported system configuration XML file.
Recommended Response Action Enable Collect System Inventory On Restart (CSIOR) using Lifecycle Controller and restart the system. Make sure that inventory collection is complete before retrying the operation. For more information, see the Lifecycle Controller Users Guide. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description An error occurred while copying the system configuration XML file from the network share. Recommended Response Action If the file is being copied from an NFS share, make sure that it is accessible from iDRAC. If the file is being copied from a CIFS share, make sure that it is accessible from iDRAC using the share credentials provided. Test the network share access using the Test Network Connection method. For more information, see the Lifecycle Controller Users Guide.
SYS048 Message Arguments System configuration XML input file contains invalid characters, arg1 at line arg2 . • arg1 = character • arg2 = line Detailed Description The operation expected a valid XML that is compliant with the system configuration schema. However, the system configuration file does not contain valid XML content. Recommended Response Action View the file in any Web browser to check for invalid characters.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS051 Message The system could not be shut down within the specified time. Detailed Description Sometimes, the operating system on the server may not allow a graceful shutdown or may not complete within the specified graceful shutdown timeout. This error indicates that the system could not be shutdown within the time specified.
Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS053 Message Successfully imported and applied system configuration XML file. Detailed Description Configuration changes specified in the system configuration XML file were successfully applied. Recommended Response Action No response action is required.
Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS055 Message Import of system configuration XML file operation completed with errors. Detailed Description The configuration specified in the system configuration XML file was applied, but there were some errors.
Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS057 Message Exporting system configuration XML file. Detailed Description The current system configuration is being collected and the system configuration XML file is being generated.
Detailed Description Running Lifecycle Controller Automated Task Execution application in Unified Extensible Firmware Interface (UEFI) environment to apply configuration changes. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
SYS060 Message Component configuration completed with errors. Detailed Description Some configuration changes for the component identified by the Fully Qualified Device Descriptor (FQDD) in the configuration job results were not successfully applied. Recommended Response Action Export the Lifecycle Log and identify the configuration changes that did not complete or retrieve the configuration results using the GetConfigResults() method.
Server Administrator Trap ID Not Applicable SYS062 Message Input file for import configuration operation is invalid. The expected XML root element was not found. Detailed Description The input file for the import configuration operation does not contain a valid XML root element. Recommended Response Action Open the input file in any Web browser to check for invalid content before the expected root element.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS064 Message Arguments Input file for import configuration operation is invalid at line arg1 . • arg1 = line Detailed Description The input file for the import configuration operation contains invalid XML data at the line specified. Recommended Response Action Open the input file in any Web browser to check for invalid content before the expected root element.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS066 Message No changes detected for iDRAC, System, or Lifecycle Controller configuration. Detailed Description No iDRAC, System, or Lifecycle Controller configuration changes were applied. The settings specified in the system configuration XML input file match the current configuration for these components.
Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS068 Message Configuration changes that require system reboot were not applied. Detailed Description Some configuration changes that require system reboot were not applied because the values specified in the input XML file are incorrect.
Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS070 Message Configuration changes that require system reboot were not applied. Detailed Description The configuration changes that require system reboot into the UEFI environment on the system did not complete for all components.
Recommended Response Action Make sure the Collect System Inventory On Restart (CSIOR) Lifecycle Controller setting is enabled and reboot the system. Retry the operation after CSIOR has completed. If the problem persists, reset iDRAC by pressing the System ID button for at least 15 seconds and retry the operation after iDRAC has fully restarted. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description The import of system configuration XML file operation completed with errors because the Lifecycle Controller State was disabled in the input XML. Configuration changes requiring a system reboot were not applied. Recommended Response Action Enable the Lifecycle Controller State setting and retry the operation. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
SYS075 Message Unable to perform the import operation because the specified file does not exist on the remote share. Detailed Description Unable to perform the import operation because the specified file does not exist on the remote share. Recommended Response Action Make sure the import configuration file exists on the remote share before retrying the operation. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SYS077 Message Unable to perform the preview operation because the specified file does not exist on the remote share. Detailed Description Unable to perform the preview operation because the specified system configuration XML file does not exist on the remote share. Recommended Response Action Make sure the configuration XML file to be previewed exists on the remote share before retrying the operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS079 Message The Preview operation indicates the input file for system configuration XML is not compliant with the configuration XML schema. Detailed Description The Preview operation indicates the input file for system configuration XML is not compliant with the configuration XML schema.
Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS081 Message Successfully previewed system configuration XML file import operation. Detailed Description Successfully previewed system configuration XML file import operation. Recommended Response Action No response action is required.
Recommended Response Action Identify the configuration changes that cannot be completed successfully by 1) Export the Lifecycle Log review the configuration results in the entries for the preview job or 2) Retrieve the preview operation configuration results using the GetConfigResults() method. Retry those changes that did not complete in a separate import operation. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
SYS084 Message Export of ePSA Diagnostics results did not complete successfully because the iDRAC internal storage containing the results could not be accessed. Detailed Description Export of ePSA Diagnostics results did not complete successfully because the iDRAC internal storage containing the results could not be accessed. Recommended Response Action Do the following: 1) Delete all jobs, 2) Reset iDRAC by pressing the System ID button for at least 15 seconds, and 3) Retry the operation.
Server Administrator Trap ID Not Applicable SYS086 Message Unable to copy the ePSA Diagnostics results file to the network share. Detailed Description Unable to copy the ePSA Diagnostics results file to the specified network share. Recommended Response Action If the results are being exported to an NFS share, make sure that the network share is accessible from iDRAC.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS088 Message Arguments Estimated time for applying configuration changes is arg1 seconds. • arg1 = configuration time Detailed Description Applying the changes defined in the configuration XML file will take approximately the estimated time identified in the message. Recommended Response Action No response action is required.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS090 Message The configuration XML input file contains unsupported DOCTYPE tags. Detailed Description The configuration XML Input file contains XML DOCTYPE tags which may contain injection security threats. The XML DOCTYPE tag is not supported in configuration XML files.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS092 Message The iDRAC is collecting information about the server for a Tech Support Report. Detailed Description The iDRAC is collecting information about the server for a Tech Support Report. Recommended Response Action No response action is required.
Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS094 Message The iDRAC is unable to start the Tech Support Report job, because a report collection job is already running on the server.
Category System Health Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS096 Message Required ePSA Diagnostics binary does not exist. Detailed Description The required ePSA Diagnostics binary does not exist or cannot be found in the iDRAC internal storage.
Recommended Response Action If further configuration changes are required for the system, the Lifecycle Controller State must be enabled prior to attempting the configuration change. To enable the Lifecycle Controller State, run the racadm command "racadm set LifecycleController.LCAttributes.LifecycleControllerState Enabled". Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Detailed Description The diagnostics results could not be exported because either the diagnostics tests were never run on the system or the results could not be found on the internal storage of the iDRAC. Recommended Response Action Run the RunEPSADiagnostics method to make sure that the diagnostics results are available, and then retry the operation. Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
SYS1000 Message System is turning on. Detailed Description System is turning on. Recommended Response Action No response action is required. Category Audit Subcategory SYS = System Info Severity Severity 3 (Informational) Trap/EventID 8579 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS1001 Message System is turning off. Detailed Description System is turning off.
Server Administrator Trap ID Not Applicable SYS1002 Message System is performing a power cycle. Detailed Description System is performing a power cycle. Recommended Response Action No response action is required. Category Audit Subcategory SYS = System Info Severity Severity 3 (Informational) Trap/EventID 8579 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS101 Message Server Administor Data Manager service has started. Detailed Description The Server Administratort Data Manager service has started. Recommended Response Action No response action is required. Category Audit Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default OS Log;None Server Administrator Event ID 5009 Server Administrator Trap ID Not Applicable SYS103 Message Administrator has started. Detailed Description The Server Administrator has started. Recommended Response Action No response action is required. Category Audit Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default OS Log;None Server Administrator Event ID 5000 Server Administrator Trap ID Not Applicable SYS105 Message Arguments Unable to process the event: arg1 Date and time of event: arg2 . • arg1 = event • arg2 = date time Detailed Description The current software version is unable to process this event because of an internal error. Recommended Response Action Contact your service provider.
Category Audit Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default OS Log;None Server Administrator Event ID 5007 Server Administrator Trap ID Not Applicable SYS107 Message A system reboot was initiated by the user. Detailed Description The user initiated a system reboot. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Audit Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default SNMP Alert;OS Log;None Server Administrator Event ID 5007 Server Administrator Trap ID 5007 SYS109 Message A system power cycle was initiated by the user. Detailed Description The user has initiated a system power cycle action. Recommended Response Action No response action is required.
Detailed Description The actions will shut down the operating system and then reboot the system. Recommended Response Action No response action is required. Category Audit Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default SNMP Alert;OS Log;None Server Administrator Event ID 5007 Server Administrator Trap ID 5007 SYS111 Message The actions Shutdown OS First and Power Off System were initiated by the user.
SYS112 Message The actions Shutdown OS First and Power Cycle System were initiated by the user. Detailed Description The actions will shut down the operating system and then power cycle the system. Recommended Response Action No response action is required. Category Audit Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID 5007 SYS114 Message Arguments The IPMI status for the interface: arg1 , Baseboard Management Controller (BMC): arg2 , Sensor Data Records (SDR): arg3 , System Event Log (SEL): arg4 . • arg1 = interface • arg2 = BMC • arg3 = SDR • arg4 = SEL Detailed Description IPMI is supported for identified interface, Baseboard Management Controller (BMC), Sensor Data Records (SDR), and System Event Log (SEL).
Subcategory SYS = System Info Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS116 Message Unable to determine the status of the power cord. Detailed Description The status of the power cord cannot be determined because of one of the following reasons: 1) The power cable may not be connected properly or disconnected.
Recommended Response Action No response action is required. Category System Health Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS118 Message The input power supply is not available.
Detailed Description The OS collector cannot be exposed to the host server because of communication issues between the iDRAC and server OS. Recommended Response Action Do the following: 1) Retry the operation. 2) If the issue persists, restart the iDRAC and server OS. Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SYS121 Message The operation to collect OS and Application Data was cancelled using iDRAC Web UI. Detailed Description The operation to collect OS and Application Data was cancelled using iDRAC Web UI. Recommended Response Action No response action is required. Category System Health Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS123 Message OS Collector: An unexpected issue has been encountered. Detailed Description An unexpected issue has occured. This could be because the application encountered an unexpected exception or was terminated by a user. This issue could also be because the application was running in an unsupported OS. Recommended Response Action Do the following: 1) Retry the operation.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS125 Message OS Collector: Unable to communicate with WMI services. Detailed Description The OS Collector application is unable to communicate with the WMI service.
Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS127 Message OS Collector: Unable to collect OS log data Detailed Description OS log data was not collected. An issue occurred while collecting OS log data because of an unknown exception.
Recommended Response Action Do the following: 1) Retry the operation. 2) If the issue persists, reinstall the latest OS Collector on the iDRAC, and then retry the operation. Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description Unable to create the final zip archive name because the Service Tag and time stamp could not be retrieved from OS interfaces. Recommended Response Action Do the following: 1) On Windows, restart the WMI service and retry the operation, 2) Restart the OS and retry the operation. Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
SYS132 Message OS Collector: Unable to communicate with OS Collector IPMI library. Detailed Description An issue occurred while loading the OS Collector IPMI library. This may be because the OS collector binary images are not valid and need to be re-installed. Recommended Response Action Do the following: 1) Retry the operation. 2) If the issue persists, reinstall the latest OS Collector on the iDRAC, and then retry the operation.
Server Administrator Trap ID Not Applicable SYS134 Message OS Collector: Zip archive size exceeded the limit. Detailed Description The report size is more than the 30MB allowed size which will cause a truncated, partial report to be generated. Recommended Response Action Remove older log entries so that the final zip archive size can be reduced. Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS136 Message An issue was encountered while communicating with iDRAC Service Module (iSM) present on the operating system. Detailed Description An issue was encountered while communicating with iDRAC Service Module (iSM) present on the operating system. Recommended Response Action Do the following: 1) Restart the iDRAC Module Service on the OS and retry the operation.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS138 Message Unable to start the collection of OS and Application Data because the server is turned off. Detailed Description Unable to start the collection of OS and Application Data because the server OS is turned off. Recommended Response Action Turn on the server and wait until the OS finishes booting, and then retry the operation.
Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS140 Message Unable to start the collection of OS and Application Data because the iDRAC Service Module (iSM) is not running in the server OS.
Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS142 Message The OS driver pack is deleted. Detailed Description The OS driver pack is deleted because of a System Erase operation. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS144 Message Starting controller hardware cache data erase operations.
Detailed Description vFlash SD Card data is deleted because of a System Erase operation. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS146 Message Starting secure erase-capable drive erase operations.
SYS147 Message Starting non-secure erase-capable drive erase operations. Detailed Description Starting non-secure erase-capable drives erase operations because of a System Erase operation request. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SYS149 Message The process of resetting iDRAC to default settings is initiated. Detailed Description Initiating iDRAC reset to defaults operation because of a System Erase operation. The iDRAC will restart after firmware default values are restored. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS151 Message Arguments Completed System Erase Job ID: arg1 • arg1 = job ID Detailed Description A System Erase job with the job ID identified in the message is completed. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS153 Message Arguments Deleting hardware cache data for controller: arg1 . • arg1 = device name Detailed Description The non-volatile cache of the controller identified in the message is being erased. Recommended Response Action No response action is required.
Detailed Description Initiating secure erase operation on secure erase-capable drives for the controller identified in the message. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
SYS156 Message Erase operations for System Erase tasks successfully completed. Detailed Description The requested component erase tasks of the System Erase operation is successfully completed. Recommended Response Action No response action is required. Category Configuration Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SYS158 Message Hardware cache erase is unsuccessful. Detailed Description Unable to erase hardware caches during the System Erase operation. Recommended Response Action Retry the System Erase operation with only the hardware cache erase option selected. Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS160 Message The Lifecycle Controller logs are cleared. Detailed Description The Lifecycle Controller log data deleted as part of a System Erase operation. All previously stored information is no longer available. Recommended Response Action No response action is required.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS162 Message Turning on the server to perform System Erase tasks. Detailed Description The server will be turned on to enter UEFI System Services Manager (SSM). The storage-related erase operations selected, if any, will be processed by SSM. Recommended Response Action No response action is required.
Subcategory SYS = System Info Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS164 Message Access to Lifecycle Controller internal storage was not acquired. Detailed Description The System Erase operation attempted to access Lifecycle Controller internal storage that is already being accessed by another function.
Detailed Description One or more Tech Support Report data collection options selected did not complete successfully. Recommended Response Action Look at the Lifecycle Log for exception messages and resolve the issues described. Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
SYS167 Message TTY Log data export did not complete within the allocated time. Detailed Description The TTY Log data export did not complete within the allocated time. Currently the maximum allocated time is 20 minutes. Recommended Response Action Reset the iDRAC and retry the operation. Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable SYS169 Message The iDRAC Service Module installed on the operating system is not up to date and does not support the Technical Support Report feature. Detailed Description The iDRAC Sevice Module installed on the operating system is not up to date and does not support the Technical Support Report.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS171 Message Unable to successfully complete the import operation because not all hash password values have been entered. Detailed Description The import operation cannot be completed successfully because the SHA1v3Key and the MD5V3Key values must both be supplied. Recommended Response Action The SHA1v3Key and the MD5V3Key values must be entered together for an import operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS173 Message Unable to retrieve the TTY Log because another operation is in progress on the RAID controller. Detailed Description The TTY Log cannot be retireved because another operation is in progress on the RAID controller. Recommended Response Action Do the following: 1) View the job queue and make sure all jobs are in a completed state. 2) Retry the operation.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS175 Message No device configuration could be identified for the specified FQDDs. Detailed Description Selective Export / Import could not find any matches for the FQDDs specified. Recommended Response Action Ensure that only valid FQDDs are provided as input to the Target parameter.
Category Configuration Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS177 Message There was an issue retrieving Hardware data. Detailed Description There was an issue retrieving Hardware data from the iDRAC internal storage.
Detailed Description Unable to retrieve TTY log data because no storage controllers are detected in the server. Recommended Response Action Make sure that at least one storage controller is present in the server, and then retry the operation. Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
SYS180 Message Arguments There was an issue encountered when attempted to export TTY Log data for the storage controller arg1 . • arg1 = controller name Detailed Description The TTY log data of the storage controller identified in the message cannot be exported because an issue was encountered while communicating with the controller. Recommended Response Action While exporting the TTY log, make sure that the server is not in BIOS POST, and then retry the operation.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS182 Message Unable to collect OS and Application Data because another Lifecycle Controller operation is currently in progress. Detailed Description Collecting OS and Application Data cannot be completed because Lifecycle Controller is used by another operation. Recommended Response Action Make sure all other Lifecycle Controller operations are finished and retry the operation.
Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS184 Message Unable to compute the checksum because OS Collector files are not readable. Detailed Description The checksum cannot be computed because OS Collector files are not readable.
Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable SYS186 Message Unable to start the collection of TTY log data because the server is turned off. Detailed Description Unable to start the collection of TTY log data because the server OS is turned off.
Recommended Response Action Retry the operation after the server has finished starting and POST has completed. Category System Health Subcategory SYS = System Info Severity Severity 2 (Warning) LCD Message No LCD message display defined.
TMP Event Messages 61 TMP0100 Message Arguments The system board arg1 temperature is less than the lower warning threshold. • arg1 = name Detailed Description Ambient air temperature is too cool. Recommended Response Action Check system operating environment. Category System Health Subcategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined.
Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message System board temperature is outside of range. Check Fans Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0102 Message Arguments The system board arg1 temperature is greater than the upper warning threshold.
Arguments • arg1 = name Detailed Description Ambient air temperature is too warm or one or more fans may have failed. Recommended Response Action Check system operating environment and review event log for fan failures. Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message System board temperature is outside of range.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0105 Message Arguments The system board arg1 temperature is within range. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory TMP = Temperature Severity Severity 3 (Informational) Trap/EventID 2163 LCD Message No LCD message display defined.
Category System Health Subcategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0107 Message The memory module arg1 temperature is less than the lower critical threshold. Arguments • Detailed Description Ambient air temperature is too cool.
Arguments • arg1 = number Detailed Description Ambient air temperature is too warm or one or more fans may have failed. Recommended Response Action Check system operating environment and review event log for fan failures. Category System Health Subcategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0110 Message Arguments The memory module arg1 temperature is outside of range. • arg1 = number Detailed Description Ambient air temperature is too warm or cool. Recommended Response Action Check system operating environment and review event log for fan failures.
Category System Health Subcategory TMP = Temperature Severity Severity 3 (Informational) Trap/EventID 2163 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0112 Message Arguments The arg1 temperature is less than the lower warning threshold. • arg1 = name Detailed Description Ambient air temperature is too cool.
Arguments • arg1 = name Detailed Description Ambient air temperature is too cool. Recommended Response Action Check system operating environment. Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message The temperature is outside of range.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0115 Message Arguments The arg1 temperature is greater than the upper critical threshold. • arg1 = name Detailed Description Ambient air temperature is too warm or one or more fans may have failed. Recommended Response Action Check system operating environment and review event log for fan failures.
Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message The temperature is outside of range. Check Fans Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0117 Message Arguments The arg1 temperature is within range. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
Detailed Description Ambient air temperature is too cool. Recommended Response Action Check system operating environment. Category System Health Subcategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0119 Message The system inlet temperature is less than the lower critical threshold.
TMP0120 Message The system inlet temperature is greater than the upper warning threshold. Detailed Description Ambient air temperature is too warm. Recommended Response Action Check system operating environment. Category System Health Subcategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable TMP0122 Message The system inlet temperature is outside of range. Detailed Description Ambient air temperature is too warm or cool. Recommended Response Action Check system operating environment. Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message Inlet temperature is outside of range .
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0124 Message Disk drive bay temperature is less than the lower warning threshold. Detailed Description Ambient air temperature is too cool. Recommended Response Action Check system operating environment. Category System Health Subcategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 2162 LCD Message No LCD message display defined.
Trap/EventID 2161 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0126 Message Disk drive bay temperature is greater than the upper warning threshold. Detailed Description Ambient air temperature is too warm or one or more fans may have failed. Recommended Response Action Check system operating environment and review event log for fan failures.
Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0128 Message Disk drive bay temperature is outside of range. Detailed Description Ambient air temperature is too warm or cool.
Recommended Response Action No response action is required. Category System Health Subcategory TMP = Temperature Severity Severity 3 (Informational) Trap/EventID 2163 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0130 Message The control panel temperature is less than the lower warning threshold. Detailed Description Ambient air temperature is too cool.
TMP0131 Message The control panel temperature is less than the lower critical threshold. Detailed Description Ambient air temperature is too cool. Recommended Response Action Check system operating environment. Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable TMP0133 Message The control panel temperature is greater than the upper critical threshold. Detailed Description Ambient air temperature is too warm or one or more fans may have failed. Recommended Response Action Check system operating environment and review event log for fan failures. Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0135 Message The control panel temperature is within range. Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory TMP = Temperature Severity Severity 3 (Informational) Trap/EventID 2163 LCD Message No LCD message display defined.
Trap/EventID 2161 LCD Message Insufficient system cooling detected. Check fans Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0137 Message The system cooling is working normally. Detailed Description The system cooling is working normally. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory TMP = Temperature Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0200 Message Arguments CPU arg1 temperature is less than the lower warning threshold. • arg1 = number Detailed Description System performance may be degraded.
TMP0201 Message Arguments CPU arg1 temperature is less than the lower critical threshold. • arg1 = number Detailed Description System performance may be degraded. Recommended Response Action Check system operating environment. Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message CPU temperature is outside of range.
LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0203 Message Arguments CPU arg1 temperature is greater than the upper critical threshold. • arg1 = number Detailed Description System performance may be degraded. Recommended Response Action Check system operating environment, fans, and heatsinks.
Recommended Response Action Check system operating environment, fans, and heatsinks. Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) Trap/EventID 2161 LCD Message CPU temperature is outside of range. Check fans Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP0205 Message Arguments CPU arg1 temperature is within range.
TMP0300 Message The Enhanced Cooling Mode feature is enabled. Detailed Description The Enhanced Colling Mode feature is enabled. Recommended Response Action No response action is required. Category System Health Subcategory TMP = Temperature Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable TMP0302 Message Unable to set Enhanced Cooling Mode because the required power or fan configuration is not available. Detailed Description The Enhanced Colling Mode feature cannot be enabled because the necessary power or fan configuration is not available. Recommended Response Action Do the following: 1) Check the available power and the fan configuration.
Subcategory TMP = Temperature Severity Severity 2 (Warning) Trap/EventID 4210 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2100 Server Administrator Trap ID 105300 TMP1001 Message Arguments arg1 has crossed the minimum warning threshold. • arg1 = tempsensor name Detailed Description The enclosure is too cold. Recommended Response Action Check whether the thermostat setting is too low and whether the room temperature is too cool.
Arguments • arg1 = tempsensor name Detailed Description The enclosure is too hot. A variety of factors can cause the excessive temperature. For example, a fan may have failed, the thermostat may be set too high, or the room temperature may be too hot. Recommended Response Action Check for factors that may cause overheating. For example, verify that the enclosure fan is working. You should also check the thermostat settings and examine whether the enclosure is located near a heat source.
Server Administrator Event ID 2103 Server Administrator Trap ID 105400 TMP1004 Message Arguments arg1 has returned to normal. • arg1 = tempsensor name Detailed Description The enclosure is operating under normal temperature. Recommended Response Action No response action is required. Category Storage Subcategory TMP = Temperature Severity Severity 3 (Informational) Trap/EventID 4211 LCD Message No LCD message display defined.
Category Storage Subcategory TMP = Temperature Severity Severity 3 (Informational) Trap/EventID 4211 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2154 Server Administrator Trap ID 105100 TMP500 Message Arguments The arg1 sensor has failed with value the arg2 degrees Celsius. • arg1 = sensor name • arg2 = temperature Detailed Description A temperature sensor identified in the message has failed.
TMP501 Message Arguments Unable to read the arg1 sensor value. • arg1 = sensor name Detailed Description A temperature sensor identified in the message has failed. This condition can cause system performance issues and degradation in the moitoring capability of the system. Recommended Response Action Verify the Embedded System Management (ESM) Log for any sensor related faults. If there is a failed sensor, replace the system board. For more information, contact your service provider.
LCD Message No LCD message display defined. Initial Default SNMP Alert;OS Log;None Server Administrator Event ID 5052 Server Administrator Trap ID 5052 TMP503 Message Arguments The arg1 sensor state has changed to a warning state with a value of arg2 degrees Celsius. • arg1 = sensor name • arg2 = temperature Detailed Description The temperature sensor identified in the message is faulty, or the temperature exceeds the warning threshold.
• arg2 = temperature Detailed Description The temperature sensor identified in the message is faulty, or the temperature exceeds the critical threshold. This condition can cause system performance issues and degradation in the moitoring capability of the system. Recommended Response Action Review system power policy, check system logs for temperature related failures. Category System Health Subcategory TMP = Temperature Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID 5055 TMP6 Message Arguments The temperature probe minimum warning value was changed on arg1 . • arg1 = Enclosure name Detailed Description You have changed the value for the minimum temperature probe warning threshold. This alert is provided for informational purposes. Recommended Response Action No response action is required.
Severity Severity 1 (Critical) Trap/EventID 4209 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMP8500 Message Arguments I/O Module arg1 temperature exceeded operating range. • arg1 = iom slot name Detailed Description The temperature of the I/O Module identified in the message has increased beyond the operational range. Thermal protection shut down the I/O Module.
Detailed Description System was unable to read planar board or control panel temperature sensors. The fan speed was increased to protect system hardware. Recommended Response Action Remove AC power from the system and reapply AC power. Check to see if the issue is resolved. If the issue persists, contact your service provider. Category Audit Subcategory TMP = Temperature Severity Severity 2 (Warning) LCD Message No LCD message display defined.
TMPS Event Messages 62 TMPS0100 Message Inlet temperature is above warning level for extended duration. Detailed Description Inlet temperature has been above the warning threshold for duration of 8% or more for the operational time during the last one year. Recommended Response Action This condition will occur if the ambient temperature is high. Make sure the ambient temperature of the environment is in normal range.
Trap/EventID 2522 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TMPS0102 Message Inlet temperature is above warning level for extended duration. Detailed Description Inlet temperature has been above the warning threshold for duration of 10% or more for the operational time during the last one year.
Category System Health Subcategory TMPS = Temperature Statistics Severity Severity 1 (Critical) Trap/EventID 2521 LCD Message No LCD message display defined.
TST Event Messages 63 TST100 Message The operation was successful. Detailed Description The operation completed successfully. Recommended Response Action No response action is required. Category Configuration Subcategory TST = Test Alert Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TST101 Message Resource allocation failure.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TST102 Message Email alert destination address not configured. Detailed Description The destination address of the email is not configured. Recommended Response Action Configure the email alert destination address and retry the operation. Category Configuration Subcategory TST = Test Alert Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TST104 Message SNMP traps not configured. Detailed Description The SNMP trap being tested is not properly configured. Recommended Response Action Configure the SNMP trap and retry the operation. If the issue persists, reset iDRAC.
Category Configuration Subcategory TST = Test Alert Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable TST106 Message Email alert destination address not configured. Detailed Description The email alert being tested is not properly configured. Recommended Response Action Configure the email alert and retry the operation. If the failure persists, reset iDRAC.
UEFI Event Messages 64 UEFI0000 Message CPU Exception Type 0x00: Divide by Zero (Software). Detailed Description A CPU type 0x00, divide by zero exception, (type 0x00) occurred in the pre-boot UEFI environment. The software attempted to do a mathematical divide by zero, an illegal operation. Recommended Response Action Recently installed hardware or updated software may cause this exception.Update or remove the hardware or software.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0002 Message CPU Exception Type 0x04: Overflow (Software). Detailed Description A CPU overflow exception (type 0x04) occurred in the pre-boot UEFI environment. Recommended Response Action Recently installed hardware or updated software may cause this exception. Update or remove the hardware or software.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0004 Message CPU Exception Type 0x06: Invalid Opcode (Software). Detailed Description A CPU invalid opcode exception (type 0x06) occurred in the pre-boot UEFI environment. The software attempted to execute invalid code. Recommended Response Action Recently installed hardware or updated software may cause this exception.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0006 Message CPU Exception Type 0x08: Double Fault (Software). Detailed Description A CPU double fault exception (type 0x08) occurred. Recommended Response Action Recently installed hardware or updated software may cause this exception. Update or remove the hardware or software.
Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0008 Message CPU Exception Type 0x0A: Invalid Task Segment State Segment (TSS) (Software). Detailed Description A CPU invalid task segment state (TSS) exception (type 0x0A) occurred in the preboot UEFI environment.
Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0010 Message CPU Exception Type 0x0C: Stack-Segment Fault (Software). Detailed Description A CPU stack-segment fault (type 0x0C) exception occurred in the pre-boot UEFI environment.
Recommended Response Action Recently installed hardware or updated software may cause this exception. Update or remove the hardware or software. Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0012 Message CPU Exception Type 0x0E: Page Fault (Software).
Detailed Description A CPU floating point error (type 0x10) exception occurred in the pre-boot UEFI environment. Recommended Response Action Recently installed hardware or updated software may cause this exception. Update or remove the hardware or software. Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
UEFI0015 Message Lifecycle Controller (LC) firmware was not accessible and is therefore in Recovery mode. Detailed Description The BIOS is unable to access the Lifecycle Controller firmware. No Lifecycle Controller functionality is available while in Recovery Mode. Recommended Response Action Perform the following actions: 1)Reboot the system. 2) Press F2 during boot to enter System Setup. 3) Select iDRAC Settings then Lifecycle Controller. 4) Change Lifecycle Controller back to Enabled.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0017 Message Lifecycle Controller (LC) firmware was not accessible and is therefore in Recovery mode. Detailed Description Unable to locate a file required to run Lifecycle Controller. No Lifecycle Controller functionality is available while in Recovery Mode.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0019 Message Lifecycle Controller (LC) is unable to complete a requested task or function and prevented the boot process from completing on multiple attempts. LC is in Recovery Mode.
Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0023 Message BIOS is unable to send the End of POST message to Management Engine because the Management Engine is not responding.
Recommended Response Action Remove input power from the system, wait for 30 seconds, and re-apply input power. Turn on the system. Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0025 Message Unable to initialize Management Engine firmware.
Detailed Description iDrac is not responding to BIOS commands. The BIOS will reset the system to retry the initialization process. Recommended Response Action Wait for the BIOS to reset the system and reinitialize the iDRAC. If the issue persists, remove input power from the system, wait for 30 seconds, and re-apply input power. Turn on the system. Category System Health Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
UEFI0028 Message iDRAC is not responding after a recovery system reset was performed. Detailed Description The iDRAC is not responding after a recovery system reset was performed. BIOS will continue POST startup with iDRAC in a non functional state. Recommended Response Action Remove input power from the system, wait for 30 seconds, and re-apply input power. Turn on the system.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0030 Message A keyboard device is not connected to the system. Detailed Description A keyboard device is not connected to the system. Recommended Response Action Connect a keyboard device to the system. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0032 Message Unable to initialize the TPM chip because the TPM chip is not functioning. Detailed Description The TPM chip cannot be initialized because the TPM chip is not functioning.
Recommended Response Action To change the system BIOS settings and persistently save the settings, remove the NVRAM_CLR jumper and then go to the System Setup to configure system settings. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description The BIOS passwords are disabled because the PWRD_EN jumper is removed from the system board. Recommended Response Action To enable the BIOS passwords, install the PWRD_EN jumper. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
UEFI0037 Message Unable to communicate with iDRAC because of an issue in the iDRAC Shared Memory Architecture (SMA) Intelligent Platform Management Interface (IPMI). Detailed Description Unable to communicate with iDRAC because of an issue in the iDRAC Shared Memory Architecture (SMA) Intelligent Platform Management Interface (IPMI). Continuing to boot may result in unexpected power loss because of unknown power inventory and unavailability of features such as active power management, thermal management.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0039 Message Unable to communicate with iDRAC because of an issue in the iDRAC Keyboard Controller Style (KCS) Intelligent Platform Management Interface (IPMI). Detailed Description Unable to communicate with iDRAC because of an issue in the iDRAC Keyboard Controller Style (KCS) Intelligent Platform Management Interface (IPMI).
firmware on the system. For information about the issue, see System Event Log (SEL). Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0041 Message Unable to enable the TXT feature because the Virtualization Technology (VT) feature is not enabled on the processor.
Detailed Description Unable to enable the TXT feature because Trusted Platform Module (TPM) configuration is invalid. Recommended Response Action Go to System Setup > System Security page, select the "On with pre-boot measurement" option for TPM Security, and click the "Activate" option under TPM command. Restart the system, go to System Setup > System Security page, and then enable TXT.
UEFI0044 Message Unable to enable the TXT feature because the motherboard chipset does not support TXT. Detailed Description Unable to enable the TXT feature because the processor does not support TXT. Recommended Response Action Contact your service provider. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable UEFI0046 Message An issue in observed in the previous invocation of TXT SINIT Authenticated Code Module (ACM) because the TXT information stored in the TPM chip may be corrupted. Detailed Description An issue in observed in the previous invocation of TXT SINIT Authenticated Code Module (ACM) because the TXT information stored in the TPM chip may be corrupted. Recommended Response Action Do one of the following: 1) Update the BIOS firmware.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0048 Message The Collect System Inventory on Restart (CSIOR) operation is not performed during this restart because Lifecycle Controller is not functioning. Detailed Description The Collect System Inventory on Restart (CSIOR) operaiton is not performed during this restart because Lifecycle Controller firmware could not be accessed or run properly.
Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0050 Message The process of collecting Brand information is started. Detailed Description The rebranding process is started. Recommended Response Action No response action is required.
Category Work Notes Subcategory UEFI = UEFI Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0052 Message Unable to complete the rebranding operation because of the issue(s) displayed earlier. Detailed Description The rebranding process cannot be completed because of the reasons identified on the computer screen.
Recommended Response Action No response action is required. Category Work Notes Subcategory UEFI = UEFI Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0054 Message Debranding process is completed. The system is being restarted. Detailed Description Debranding process is completed. The system is being restarted.
Detailed Description The debranding process cannot be completed because of the reasons identified on the computer screen. Recommended Response Action Check the screen display for details of the failure. Retry the debrand process again, or update the system BIOS and then retry. Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
UEFI0057 Message A Machine-Check Exception (MCE) error has occurred. Detailed Description The MCE is logged during Power-on-Self-Test (POST). MCE could have occured during either the current or the previous POST. Recommended Response Action Check the System Event Log (SEL) to identify Machine-Check Exception (MCE) event source. Resolve the issue identified in the SEL that caused the MCE. For further information, contact your service provider.
Server Administrator Trap ID Not Applicable UEFI0059 Message The Power Supply Units (PSUs) in the system do not match. Detailed Description The Power Supply Units (PSUs) in the system do not match. Recommended Response Action Check the PSU types and make sure they are appropriately matched, and then retry the operation. For more information, see the platform Owners Manual.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0061 Message The request to change attributes is being processed. Detailed Description The request to change one or more attribute(s) is being processed. Recommended Response Action No response action is required. Category Updates Subcategory UEFI = UEFI Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0063 Message Unable to change an attribute because of issues in the Attribute Configuration Interface (ACI) data block. Detailed Description An attribute cannot be successfully configured because of an issue in the ACI data block. Recommended Response Action Check the ACI data block for any invalid configuration dtata and settings, and then retry the operation.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0065 Message One or more attributes are successfully configured. The system will be automatically turned off in 5 seconds. Detailed Description One or more attributes are successfully configured. The system is automatically turned off in 5 seconds. Recommended Response Action No response action is required.
Recommended Response Action Do one of the following: 1) Turn off the input power to the system and turn on again. 2) Update the PCIe device firmware. If the issue persists, contact your service provider. Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
UEFI0068 Message The mezzanine card configuration used is not supported on this Chassis. Detailed Description The mezzanine card configuration used is not supported on this Chassis. Server modules used in different Chassis may require cards with different configuration properties. For more information, contact your service provider. Recommended Response Action Make sure that a supported mezzanine card is used and retry the operation.
Server Administrator Trap ID Not Applicable UEFI0070 Message One or more correctable PCIe errors have occurred. Detailed Description One or more correctable PCIe errors have occurred. Data about the errors are logged into SEL during the POST operation. Recommended Response Action Check the System Event Log (SEL) to identify the PCIe device, and then update its firmware.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0072 Message Arguments Unable to load the firmware from arg1 because of the Secure Boot policy. • arg1 = device name Detailed Description When the Secure Boot feature is enabled, the system BIOS authenticates each UEFI driver against the Secure Boot policy.
Arguments • arg1 = Boot Option name Detailed Description When the Secure Boot feature is enabled, the system BIOS authenticates each boot option against the Secure Boot policy. If a boot option does not meet the policy criteria, the system BIOS does not boot to the boot option and displays this message. The Secure Boot policy consists of authorized and unauthorized X.509 certificates; signed boot images must chain to an authorized certificate.
Recommended Response Action Review the Secure Boot policy settings in System Setup > System BIOS > Security Settings page. If policy changes were expected, no action is necessary. Otherwise, modify the Secure Boot policy settings as needed. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description A Corrected Machine Check error(s) has occured. Recommended Response Action Check the System Event Log (SEL) to identify the Corrected Machine Check (CMC) errors. Resolve the issue identified in the SEL that caused the CMC. Category System Health Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
UEFI0078 Message One or more Machine Check errors occurred in the previous boot. Detailed Description One or more Machine Check errors occurred in the previous boot. Recommended Response Action Check the System Event Log (SEL) to identifiy the source of the Machine Check error and resolve the issues. Category System Health Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable UEFI0080 Message Arguments PCIe link speed is not optimal for arg1 . Expected link speed: Gen arg2 and actual link speed: Gen arg3 . • arg1 = PCIe device • arg2 = generation number • arg3 = generation number Detailed Description The PCIe link speed is not optimal for the identified PCIe device. Recommended Response Action Do one of the following: 1) Turn off the input power to the system and turn on again. 2) Update the PCIe device firmware.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0082 Message The system was reset due to a timeout from the watchdog timer. Detailed Description The system was reset due to a timeout from the watchdog timer. Recommended Response Action Check the System Event Log (SEL) or crash dumps from Operating System to identify the source that caused the watchdog timer reset.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0084 Message One or more PCI Parity errors (PERR) have occurred. Detailed Description One or more PCI Parity errors (PERR) have occurred. Recommended Response Action Check the System Event Log (SEL) to identify the PCI device that caused the PERR. Update the identifed device firmware.
Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0086 Message Arguments Unsupported Small Outline Dual In-line Memory Module (SODIMM) memory is installed on RDIMM memory slot: arg1 .
Detailed Description Unsupported 4Gb technology DIMM module is installed on the memory slot indentified in the message. Recommended Response Action Remove the unsupported DIMM module from the identified memory slot and replace it with a supported module. For more information, see the platform Owners Manual. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
UEFI0089 Message Arguments Incompatible x16 data bus width DIMM is installed on memory slot: arg1 . • arg1 = slot number Detailed Description Incompatible x16 data bus width DIMM is installed on the memory slot indentified in the message. Recommended Response Action Remove the unsupported DIMM module from the identified memory slot and replace it with a supported module. For more information, see the platform Owners Manual.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0091 Message Arguments A Quad-Rank (QR) DIMM is installed on memory slot: arg1 . QR DIMMs should be installed on the first DIMM slot in a channel if there is only one QR DIMM in the channel. QR DIMMs cannot be installed on the third slot of the channel. • arg1 = slot number Detailed Description A Quad-Rank (QR) DIMM is installed on the memory slot indentified in the message.
Recommended Response Action Check the total number of ranks in each channel to make sure it does not exceed the maximum allowed limit. For more information, see the platform Owners Manual. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
UEFI0094 Message Arguments Unsupported Non-ECC memory module is installed on memory slot: arg1 . • arg1 = slot number Detailed Description Unsupported Non-ECC memory module is installed on the memory slot identified in the message. Recommended Response Action Remove all Non-ECC DIMMs and replace them with ECC DIMMs. For more information, see the platform Owners Manual.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0096 Message Unable to enable the Advanced ECC memory operating mode because the current DIMM population or system configuration does not support Advanced ECC mode. Detailed Description The Advanced ECC memory operating mode cannot be enabled because the current DIMM population or system configuration does not support Advanced ECC mode.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0098 Message Arguments The memory Built-In Self-test (BIST) has detected one or more errors on the DIMM installed on memory slot: arg1 . As a result, the corresponding DIMM has been disabled.
Detailed Description The Memory Mirroring feature cannot be enabled because the current DIMM population or hardware configuration does not support the feature. Recommended Response Action Check the DIMM population and hardware configuration to make sure the Memory Mirroring feature can be supported. For more information, see platform Owners Manual. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
UEFI0101 Message Total amount of installed memory has exceeded limit. Detailed Description The total amount of installed memory has exceeded the amount supported by the platform. Recommended Response Action Remove memory modules from the system to reduce the total amount of installed memory. For more information on installed memory limit, see the platform Owners Manual. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable UEFI0103 Message Arguments One or more memory initialization errors have occurred on memory slot: arg1 . • arg1 = slot Detailed Description One or more memory initialization error have occurred on the memory slot identified in the message. Recommended Response Action Replace the faulty memory module identified in the message.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0105 Message Unable to enable the Cluster on Die (COD) feature because of an unsupported memory configuration. Detailed Description The Cluster on Die (COD) feature cannot be enabled because of an unsupported memory configuration.
Recommended Response Action Remove input power to the system, reseat the DIMM module and restart the system. If the correctable error persists, then replace the faulty memory module identified in the message. Category System Health Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
UEFI0108 Message Arguments One or more memory errors have occurred on memory slot: arg1 . • arg1 = slot Detailed Description One or more memory errors have occurred on memory slot identified in the message. The error occured during RecEn initialization. Recommended Response Action Remove input power to the system, reseat the DIMM module and restart the system. If the issues persist, then replace the faulty memory module identified in the message.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0110 Message Arguments One or more memory errors have occurred on memory slot: arg1 . • arg1 = slot Detailed Description One or more memory errors have occurred on memory slot identified in the message. The error occurred during Write DqDqs training. Recommended Response Action Remove input power to the system, reseat the DIMM module and restart the system.
Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0112 Message Arguments One or more memory errors have occurred on memory slot: arg1 . • arg1 = slot Detailed Description One or more memory errors have occurred on memory slot identified in the message. The error occurred during the LRDIMM interface initialization.
Recommended Response Action Check the DIMM population and hardware configuration to make sure the Memory Mirroring feature can be supported. For more information, see the platform Owners Manual. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description The BIOS has recovered the Management Engine after it became unresponsive via the HECI interface. There is no performance degradation and the Management Engine is functioning normally now. Recommended Response Action The Management Engine is functioning normally now. No response action is required. Category System Health Subcategory UEFI = UEFI Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
UEFI0117 Message Card identification signature is not present on Internal Dual Secure Digital Module (IDSDM) SD card 1. Detailed Description Card identification signature is not present on Internal Dual Secure Digital Module (IDSDM) SD card 1. Recommended Response Action Do one of the following: 1) Check the IDSDM or the SD card media. 2) Try reseat or replace the SD card media. If the issue persists, contact your service provider.
Server Administrator Trap ID Not Applicable UEFI0119 Message The Internal Dual Secure Digital Module (IDSDM) RAID redundancy was lost. Detailed Description Internal Dual Secure Digital Module (IDSDM) RAID redundancy was lost. The system BIOS should have prompted the user for the rebuild process. Recommended Response Action No additional response action is required if you have followed the instructions on the screen to start the rebuild process.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0121 Message The primary SD card is missing, not responding, or in write-protected mode. Detailed Description The primary SD card is missing, not responding, or in write-protected mode. Recommended Response Action Do one of the following: 1) Install a SD card media in the primary SD card reader. 2) Reseat or replace the SD card media.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0123 Message The secondary SD card has now become the primary SD card. Detailed Description The secondary SD card has now become the primary SD card. Recommended Response Action Check the screen display or the Lifecycle Log for prior messages. If the switch is expected, then no response action is required.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0125 Message Unable to finish The Internal Dual Secure Digital Module (IDSDM) image rebuild process because of issues. Detailed Description Unable to finish The Internal Dual Secure Digital Module (IDSDM) image rebuild process because of issues.
Subcategory UEFI = UEFI Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0127 Message The secondary SD card is in write-protected mode. Detailed Description The secondary SD card is write-protected mode. Recommended Response Action No response action is required if this is intentional.
Category Configuration Subcategory UEFI = UEFI Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0129 Message The Internal Dual Secure Digital Module (IDSDM) has encountered an unknown issue. Detailed Description The Internal Dual Secure Digital Module (IDSDM) has encountered an unknown issue.
Recommended Response Action Go to the System Setup to set the current time and date. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0131 Message Unable to load one or more option ROMs because of insufficient shadow memory.
Detailed Description Unable to load one or more option ROMs because of insufficient base memory. The base memory is memory below 640K. Recommended Response Action Do one of the following: 1) Remove unused PCIe card(s) to free up option ROM space. 2) Disable unused boot protocol instances (such as PXE, iSCSI, etc.) from applicable PCIe card(s) option ROM configurations. 3) If possible, install and run the Operating System in UEFI boot mode.
UEFI0134 Message Unable to allocate Memory Mapped Input Output (MMIO) resources for one or more PCIe devices because of insufficient MMIO memory. Detailed Description Unable to allocate Memory Mapped Input Output (MMIO) resources for one or more PCIe devices because of insufficient MMIO memory. Recommended Response Action Do one of the following: 1) Remove unused PCIe card(s) to free up MMIO space. 2) Go to System Setup and enable the Memory Mapped I/O above 4GB option.
Server Administrator Trap ID Not Applicable UEFI0136 Message Unable to execute CSIOR (Collect System Inventory on Restart) because the Lifecycle Controller (LC) firmware was not accessible. Detailed Description The CSIOR (Collect System Inventory on Restart) operation cannot be executed because the Lifecycle Controller (LC) firmware was not accessible. This issue is caused by missing LC partitions. Recommended Response Action Do one of the following: 1) Restart the system and retry the operation.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0138 Message Unable to execute CSIOR (Collect System Inventory on Restart) because the Lifecycle Controller (LC) firmware was unable to complete a requested task or function. Detailed Description The CSIOR (Collect System Inventory on Restart) operation cannot be executed because the Lifecycle Controller (LC) firmware is unable to complete a requested task or function.
Category System Health Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0140 Message Unable to enter System Service Mode (SSM) because the Lifecycle Controller (LC) firmware was not accessible.
Detailed Description The System Service Mode (SSM) cannot be entered because the Lifecycle Controller (LC) firmware was not accessible. This situation is caused by missing LC files. Recommended Response Action Do one of the following: 1) Restart the system and retry the operation. 2) Update the iDRAC firmware. If the issue persists, contact your service provider. Category System Health Subcategory UEFI = UEFI Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
UEFI0143 Message Unsupported processor(s) are installed. Detailed Description Unsupported processor(s) are installed. Recommended Response Action Replace the processor(s) with supported ones. For more information about supported processors, contact your service provider. Category Configuration Subcategory UEFI = UEFI Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0145 Message The Trusted Platform Module (TPM) installed on this system is not supported. Detailed Description The Trusted Platform Module (TPM) installed on this system is not supported. Recommended Response Action Do one of the following: 1) Update the BIOS firmware. 2) Replace the TPM with a supported one. If the issue persists, contact your service provider.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable UEFI0147 Message The system hardware or cabling configuration is invalid. Detailed Description The system hardware or cabling configuration is invalid. Recommended Response Action Do the following: 1) Make sure the system cables, risers, and CPU configuration are installed correctly. 2) Reseat each PCIe riser and reconnect the cables. For more information, see the system Owners Manual.
USR Event Messages 65 USR0001 Message Arguments arg1 • arg1 = message Detailed Description No detailed description is required. Recommended Response Action No response action is required. Category Work Notes Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined.
• arg2 = ip_address Detailed Description UserID closing session from IP Address. Recommended Response Action No response action is required. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0008 Message The Default Login Warning feature is disabled.
USR0013 Message Insufficient user privileges to perform operation. Detailed Description The user does not have sufficient privileges to execute the command. Recommended Response Action Login with sufficient privileges. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable USR0015 Message The specified user does not exist. Detailed Description The specified user does not exist. Recommended Response Action Verify the existing users and enter a valid username. Category Audit Subcategory USR = User Tracking Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0017 Message No active sessions currently exist for the specified user. Detailed Description There are no active sessions on the iDRAC for the specified user. Recommended Response Action No response action is required. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0019 Message Specified user name is too long. Detailed Description The specified username exceeds the prescribed limit (255) Recommended Response Action No response action is required. Category Audit Subcategory USR = User Tracking Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0021 Message Unable to close session with the specified ID Detailed Description The session could not be closed. A possible reason is that the session does not exist. Recommended Response Action No response action is required.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0023 Message The current user privilege is not valid. Detailed Description The user privilege is invalid. This may be due to invalid combinations of privileges given to the user. Recommended Response Action Request the administrator to assign appropriate user privileges to the specific user.
Recommended Response Action No response action is required. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0031 Message Arguments Unable to log in for arg1 from arg2 using arg3 .
USR0032 Message Arguments The session for arg1 from arg2 using arg3 is logged off. • arg1 = username • arg2 = IP address • arg3 = interface name Detailed Description The session for the username, IP address, and interface identified in the message is logged off. Recommended Response Action No response action is required. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0034 Message Arguments Login attempt alert for arg1 from arg2 using arg3 , IP will be blocked for arg4 seconds.
USR0150 Message Arguments Opening a remote VNC session from IP address arg1 . • arg1 = IP address Detailed Description The VNC client is connected from the IP address identified in the message to the iDRAC VNC Server. Recommended Response Action No response action is required. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0152 Message Arguments Unable to connect the remote VNC session, beacause an incorrect VNC password was entered from the IP arg1 . • arg1 = IP address Detailed Description Could not successfully connect to the remote VNC session, because an incorrect VNC password was entered from the IP address identified in the message. Recommended Response Action Enter the correct VNC password and retry the operation.
Recommended Response Action To re-establish the remote VNC session, log in again using the VNC client. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0170 Message Arguments The Front Panel USB port is attached to iDRAC Disk.USBFront. arg1 .
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0171 Message Arguments The Front Panel USB port is detached from the iDRAC Disk.USBFront. arg1 . Device Details: Device Class arg2 , Vendor ID arg3 , Product ID arg4 . • arg1 = port number • arg2 = class • arg3 = vendor ID • arg4 = product ID Detailed Description The device identified in the message is connected to the Front Panel USB port and detached from the iDRAC.
Detailed Description The Front Panel USB Management Port Mode setting is changed as identified in the message. Recommended Response Action No response action required Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined.
USR0174 Message The Front Panel USB device is removed from the operating system. Detailed Description The Front Panel USB device is removed from the operating system. Recommended Response Action No response action is required. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0176 Message Arguments The Front Panel USB Port Over Current condition is cleared for the attached device Disk.USBFront. arg1 . • arg1 = port number Detailed Description The Front Panel USB Port Over Current condition is cleared for the port identified in the message.
Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0180 Message The Quick Sync feature is enabled because the activate button on the bezel was pressed. Detailed Description The Quick Sync feature is enabled because the activate button on the bezel was pressed.
Recommended Response Action Press the activate button on the bezel to activiate the iDRAC Quick Sync feature. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0182 Message Server information has been accessed by using the iDRAC Quick Sync feature.
Detailed Description A bezel with the iDRAC Quick Sync feature is detected. Recommended Response Action No response action is required. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR0184 Message A bezel with the iDRAC Quick Sync feature has been disconnected and the feature is not available.
USR0190 Message Arguments Peak value is reset for arg1 sensor. • arg1 = sensor type Detailed Description The peak value of the sensor identified in the message is reset. Recommended Response Action No response action is required. Category Audit Subcategory USR = User Tracking Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable USR101 Message Resource allocation failure Detailed Description Unable to allocate the resource because of the lack of memory or file space in the iDRAC firmware. Recommended Response Action Reset iDRAC and retry the operation. Category Configuration Subcategory USR = User Tracking Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR103 Message Arguments Missing parameters arg1 . • arg1 = parameter names Detailed Description One or more required parameters needed for the operation are missing. Recommended Response Action Refer to the Lifecycle Controller Remote Services documentation and provide the required parameters.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable USR105 Message The account is not configured. Detailed Description The user account used as credentials to access iDRAC is not enabled or configured to perform the operation. Recommended Response Action Retry the operation after creating the user account.
VDR Event Messages 66 VDR1 Message Arguments arg1 failed. • arg1 = VD Name Detailed Description A storage component such as a physical disk or an enclosure has failed. The failed component may have been identified by the controller while performing a task such as a rescan or a check consistency. Recommended Response Action Replace the failed component. You can identify which component has failed by locating the component that has a red "X" for its status.
Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2059 Server Administrator Trap ID 120100 VDR100 Message Arguments arg1 is unavailable because of incompatibilities with the current controller.
Server Administrator Trap ID 120100 VDR101 Message Arguments Hot Spare Protection policy deviation with severity set at Informational level occured for arg1 . • arg1 = virtual disk names Detailed Description The number of hot spares available for the virtual disks identified in the message are not compliant with Hot Spare Protection policy, whose severity is set at Informational level. Recommended Response Action Make appropriate assignments of hotspares to meet the policy.
Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VDR102 Message Arguments Hot Spare Protection policy deviation with severity set at Warning level occured for arg1 .
VDR103 Message Arguments Hot Spare Protection policy deviation with severity set at Critical level occured for arg1 . • arg1 = virtual disk names Detailed Description The number of hot spares available for the virtual disks identified in the message are not compliant with Hot Spare Protection policy, whose severity is set at Critical level. Recommended Response Action Make appropriate assignments of hotspares to meet the policy.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2393 Server Administrator Trap ID 120100 VDR105 Message Arguments The arg1 on power save mode drives is available. • arg1 = virtual disk name Detailed Description Virtual Disk creation using power save mode drives successfully completed and the Virtual Disk identified in the message is ready for use. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2404 Server Administrator Trap ID 120100 VDR107 Message Arguments Successfully resized Controller Enhanced cache ( arg1 ). • arg1 = virtual disk name Detailed Description The Controller Enhanced cache identified in the message was successfully resized.
VDR108 Message Arguments Successfully created Controller Enhanced cache ( arg1 ). • arg1 = virtual disk name Detailed Description The Controller Enhanced cache identified in the message was successfully created. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID 2414 Server Administrator Trap ID 120100 VDR11 Message Arguments arg1 has started initializing. • arg1 = virtual disk Detailed Description This message is generated after initialization of a virtual disk starts. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined.
Recommended Response Action Make sure a hot spare to the Virtual Disk identified in the message is available and back up the data on the virtual disk. Category Storage Subcategory VDR = Virtual Disk Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID 2417 Server Administrator Trap ID 120400 VDR111 Message Arguments Corrected disk storage medium error on arg1 .
VDR112 Message Arguments Deleted the arg1 . • arg1 = virtual disk Detailed Description The controller removed a virtual disk because of a delete virtual disk operation or a reset configuration operation. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID 2063 Server Administrator Trap ID 120100 VDR13 Message Arguments arg1 rebuild has started. • arg1 = VD Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined.
Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2067 Server Administrator Trap ID 120100 VDR15 Message Arguments Initialization of arg1 was cancelled. • arg1 = virtual disk Detailed Description The initialization operation could not be completed.
VDR16 Message Arguments Consistency check of arg1 failed. • arg1 = virtual disk Detailed Description A physical disk included in the virtual disk failed or there is an error in the parity information. A failed physical disk causes errors in parity information. Recommended Response Action Check that all the physical disks of the virtual disk are in a healthy condition. Replace any disks that are not healthy and restart the operation.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2077 Server Administrator Trap ID 120400 VDR18 Message Arguments Initialization of arg1 has failed. • arg1 = virtual disk Detailed Description A physical disk included in the virtual disk has failed or was removed. Recommended Response Action If a physical disk has failed, replace the physical disk. Restart the virtual disk initialization.
Recommended Response Action Recreate the virtual disk and restore data from a backup copy. Category Storage Subcategory VDR = Virtual Disk Severity Severity 1 (Critical) Trap/EventID 4353 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2081 Server Administrator Trap ID 120400 VDR2 Message Arguments arg1 returned to optimal state.
VDR20 Message Arguments arg1 rebuild failed. • arg1 = VD Name Detailed Description A physical disk included in the virtual disk has failed or is corrupt. You may also have cancelled the rebuild. Recommended Response Action Replace the failed or corrupt disk. You can identify a disk that has failed by locating the disk that has a red "X" for its status. Restart the virtual disk rebuild.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2085 Server Administrator Trap ID 120100 VDR22 Message Arguments Formatting the arg1 is completed. • arg1 = VD Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2088 Server Administrator Trap ID 120100 VDR24 Message Arguments Reconfiguration of arg1 has completed. • arg1 = virtual disk Detailed Description The re-configuration operation on the virtual disk completed.
VDR25 Message Arguments arg1 rebuild is completed. • arg1 = VD Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2114 Server Administrator Trap ID 120100 VDR27 Message Arguments The consistency check on a arg1 has been resumed. • arg1 = VD Name Detailed Description The check consistency on a virtual disk has resumed processing after a pause. Recommended Response Action This alert is provided for informational purposes.
Recommended Response Action This alert is provided for informational purposes. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2116 Server Administrator Trap ID 120100 VDR29 Message A mirrored virtual disk has been un-mirrored. Detailed Description A mirrored virtual disk is un-mirrored.
VDR3 Message Arguments Redundancy normal on arg1 . • arg1 = VD Name Detailed Description Data redundancy has been restored to a virtual disk that previously suffered a loss of redundancy. Recommended Response Action This alert is provided for informational purposes. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2118 Server Administrator Trap ID 120100 VDR31 Message Arguments Controller cache is preserved for missing or offline arg1 . • arg1 = VD Name Detailed Description The controller is getting disconnected from its virtual disk, while Input Output (IO) is in-progress. Recommended Response Action Try importing foreign disks, if any.
Detailed Description Background initialization of a virtual disk has started. This is an automated process that writes the parity or mirror data on newly created virtual disks. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined.
Server Administrator Trap ID 120100 VDR34 Message Arguments Background initialization failed for arg1 . • arg1 = virtual disk Detailed Description Background initialization of a virtual disk failed. Recommended Response Action Run a consistency check on the virtual disk. If that fails, check the health of the member drives of the virtual disk and then recreate.
Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2130 Server Administrator Trap ID 120100 VDR36 Message Arguments arg1 initialization is in-progress arg2 . • • arg1 = VD Name arg2 = progresspercent Detailed Description Virtual disk initialization is in-progress. This alert is provided for informational purposes. Recommended Response Action No response action is required.
Detailed Description Disk space that was formerly "dead" or inaccessible to a redundant virtual disk has been restored. This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined.
Server Administrator Trap ID 120100 VDR39 Message Arguments The check consistency has made corrections and completed for arg1 . • arg1 = VD name Detailed Description The virtual disk check consistency has identified issues and made corrections. For example, the check consistency may have encountered a bad disk block and remapped the disk block to restore data consistency. This alert is provided for informational purposes. Recommended Response Action No response action is required.
Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2053 Server Administrator Trap ID 120100 VDR40 Message Arguments The reconfiguration of arg1 has resumed. • arg1 = virtual disk Detailed Description This message is generated after the reconfiguration of a virtual disk resumes. Recommended Response Action No response action is required.
Arguments • arg1 = VD Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2194 Server Administrator Trap ID 120100 VDR42 Message Arguments Dedicated hot spare assigned physical disk arg1 .
Server Administrator Event ID 2195 Server Administrator Trap ID 120100 VDR43 Message Arguments Dedicated hot spare unassigned physical disk arg1 . • arg1 = args Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined.
Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2199 Server Administrator Trap ID 120100 VDR45 Message Arguments arg1 blink has been initiated. • arg1 = VD Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
Arguments • arg1 = VD Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2245 Server Administrator Trap ID 120100 VDR47 Message Arguments A disk media error was corrected on arg1 .
Server Administrator Event ID 2280 Server Administrator Trap ID 120100 VDR48 Message Arguments arg1 has inconsistent data. • arg1 = VD Name Detailed Description This alert is provided for informational purposes. The virtual disk has inconsistent data. This may be caused when a power loss or system shutdown occurs while data is being written to the virtual disk. Recommended Response Action No response action is required.
Recommended Response Action Replace the failed disks and restore from backup. Category Storage Subcategory VDR = Virtual Disk Severity Severity 1 (Critical) Trap/EventID 4353 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2310 Server Administrator Trap ID 120400 VDR5 Message Arguments arg1 was deleted. • arg1 = virtual disk Detailed Description The controller removed a virtual disk.
VDR50 Message Arguments Background Initialization (BGI) completed with uncorrectable errors on arg1 . • arg1 = virtual disk Detailed Description The background initialization task encountered errors that cannot be corrected. The virtual disk contains physical disks that have unusable disk space or disk errors that cannot be corrected. Recommended Response Action Review other messages to identify whether the physical disk that has errors.
Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2341 Server Administrator Trap ID 120100 VDR52 Message Arguments The consistency check found inconsistent parity data on arg1 . • arg1 = virtual disk Detailed Description The data on physical disk members of the virtual disk does not match. Redundancy may be lost. Recommended Response Action Rerun the consistency check task.
Arguments • arg1 = virtual disk Detailed Description The consistency check can no longer report errors in the parity data. Recommended Response Action See the storage hardware documentation for more information on consistency check operation. Contact technical support. Category Storage Subcategory VDR = Virtual Disk Severity Severity 2 (Warning) Trap/EventID 4354 LCD Message No LCD message display defined.
Server Administrator Event ID 2344 Server Administrator Trap ID 120300 VDR55 Message Arguments arg1 initialization has failed. • arg1 = VD Name Detailed Description The controller cannot communicate with attached devices. A disk may be removed or contain errors. Cables may also be loose or defective. Recommended Response Action Verify the health of attached devices. Review the Alert Log for significant events. Make sure the cables are attached securely.
Recommended Response Action Replace the missing or failed physical disk. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VDR57 Message Arguments Background Initialization in arg1 corrected medium error.
VDR58 Message Arguments Bad block medium error is detected at block arg1 on arg2 . • arg1 = args • arg2 = VD Name Detailed Description Virtual disk bad blocks are due to presence of unrecoverable bad blocks on one or more member physical disks. Recommended Response Action Recovering a physical disk bad block depends on the RAID level and state of the virtual disk. If a virtual disk is redundant, the controller can recover a bad block on a physical disk.
Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VDR6 Message Arguments arg1 configuration has changed. • arg1 = VD Name Detailed Description This alert is provided for informational purposes. Recommended Response Action No response action is required.
Detailed Description One or more physical disks included in the virtual disk have failed. If the virtual disk is non-redundant (does not use mirrored or parity data), then the failure of a single physical disk can cause the virtual disk to fail. If the virtual disk is redundant, then more physical disks have failed than you can rebuild using mirrored or parity information. Recommended Response Action Create a new virtual disk and restore from a backup.
Server Administrator Event ID 2057 Server Administrator Trap ID 120300 VDR9 Message Arguments arg1 consistency check has started. • arg1 = virtual disk Detailed Description A consistency check operation on a virtual disk has started. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined.
Category Storage Subcategory VDR = Virtual Disk Severity Severity 1 (Critical) Trap/EventID 4353 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID 2396 Server Administrator Trap ID 120400 VDR92 Message Arguments Consistency check for arg1 has completed with uncorrectable errors. • arg1 = virtual disk Detailed Description This message occurs if there are medium errors in the physical drives.
Arguments • arg1 = VD Name Detailed Description This alert message occurs if there are medium errors in the physical drives. Recommended Response Action No response action is required. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined.
Server Administrator Event ID 2381 Server Administrator Trap ID 75100 VDR95 Message Arguments Unable to log block arg1 .Bad block table on arg2 is full. • arg1 = arg • arg2 = VD Name Detailed Description This alert message occurs if the virtual disk has bad blocks. Recommended Response Action Replace the disk in the Virtual disk, generating this alert and restore from backup. You may have lost data.
Recommended Response Action Replace the disk in the Virtual disk, generating this message. Category Storage Subcategory VDR = Virtual Disk Severity Severity 3 (Informational) Trap/EventID 4355 LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VDR97 Message Arguments Patrol Read corrected a media error on arg1 .
VDR98 Message Arguments arg1 has switched active controllers. Its active path is now through arg2 . • arg1 = virtual disk • arg2 = controller name Detailed Description The virtual disk identified in the message has changed active paths. This can be because of an attempt to optimize the throughput of the system or it could be because of a controller failover. Recommended Response Action No response action is required.
Trap/EventID 4354 LCD Message No LCD message display defined.
VF Event Messages 67 VF001 Message Command successful. Detailed Description The command was successful Recommended Response Action No response action is required. Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF003 Message Arguments Missing required parameter: arg1 • arg1 = parameter name Detailed Description The required input parameter identified in the message is missing. Recommended Response Action Refer the iDRAC and Lifecycle Controller User Guides for the required input parameters for this method.
Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF005 Message Empty partition creation successful Detailed Description A partition with no image was created. Recommended Response Action No response action is required.
Recommended Response Action Do one of the following: 1) Rerun the command after about 2 minutes 2) Reset iDRAC and rerun the command. Category Configuration Subcategory VF = vFlash Media Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF0060 Message Unable to perform the requested operation. Make sure the SD card is inserted and enabled.
Detailed Description A partition with an image was created. Recommended Response Action No response action is required. Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF008 Message Image partition creation did not complete successfully.
VF009 Message Partition formatting successful Detailed Description The specified partition was formatted. Recommended Response Action No response action is required. Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF010 Message Partition formatting did not complete successfully.
Server Administrator Trap ID Not Applicable VF011 Message Wrong password Detailed Description The specified password was not correct. Recommended Response Action Verify the password supplied. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF013 Message SD card locked Detailed Description The SD card is locked by another operation. Recommended Response Action Rerun the command after about 2 minutes Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF015 Message vFlash not enabled Detailed Description Disabling vFlash was not successful because the vFlash feature is not enabled. Recommended Response Action The vFlash is disabled and an attempts to disable it will not be successful. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF017 Message SD card not initialized Detailed Description The SD card is not initialized. Recommended Response Action In order to perform this operation, first initialize the SD Card. Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF019 Message Not enough space on SD card Detailed Description The SD card is full. Recommended Response Action Check all the partitions, delete the ones that are not necessary and try this operation again.
Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF021 Message Exceeded maximum partition size of 4GB Detailed Description The size specified is greater than the maximum allowed for a partition. Recommended Response Action Try a partition size that is smaller than 4GB and the available space on the card.
Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF023 Message Partition label not unique Detailed Description Partition with this label exists. Duplicate labels are not supported. Recommended Response Action Try a different partition label.
Recommended Response Action Wait for the partition to be unlocked and check the partition status to see if it is attached. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Detailed Description This partition index has already been used. Recommended Response Action This partition index has already been used. Try a different index. Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
VF028 Message Partition already detached Detailed Description This partition is detached and attempts to detach it will fail. Recommended Response Action No response action is required. Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable VF030 Message Invalid hash type Detailed Description The specified hash type is not a valid type. Recommended Response Action Provide a valid hash type. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF031 Message Invalid partition label.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF032 Message Invalid partition type. Detailed Description The specified partition type is not a valid type. Recommended Response Action Try a partition type that is supported. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF034 Message Invalid partition access type. Detailed Description The specified partition access type is not a valid type. Recommended Response Action Try a partition access type that is supported. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF036 Message Attach partition successful. Detailed Description The partition was attached. Recommended Response Action No response action is required. Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF038 Message Detach partition successful Detailed Description The partition was detached. Recommended Response Action No response action is required. Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF040 Message Image hash verification was not successful. Detailed Description The downloaded image did not successfully complete the hash verification. Recommended Response Action Try the download again. If this issue persists, check the network connectivity.
Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF042 Message Remote file missing. Detailed Description The remote file could not be found. Recommended Response Action Check the mount area.
Recommended Response Action Try a smaller file. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF044 Message TFTP download operation was not successful. Detailed Description File transfer was not successful. This could be because of network problems or an operational problem with the file server.
Detailed Description File transfer was not successful. This could be because of network problems or an operational problem with the file server. Recommended Response Action Try the download again. If the issue persists, validate that the network share is operational. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined.
VF047 Message Unsupported SD Card. Detailed Description This is not a Dell-licensed VFlash. Recommended Response Action This feature requires a Dell SD card. Category Configuration Subcategory VF = vFlash Media Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF048 Message Initialize media successful.
Server Administrator Trap ID Not Applicable VF049 Message Initialize media operation did not complete successfully. Detailed Description The initializing SD card operation did not complete successfully. Recommended Response Action No response action is required. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VF051 Message Export partition operation did not complete successfully. Detailed Description The copying partition operation did not complete successfully. Recommended Response Action No response action is required. Category Configuration Subcategory VF = vFlash Media Severity Severity 2 (Warning) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable 2201
VFL Event Messages 68 VFL0001 Message The vFlash SD Card operation is successful. Detailed Description The requested operation for the vFlash SD Card completed successfully. Recommended Response Action No response action is required. Category Configuration Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0003 Message Arguments Partition arg1 does not exist. • arg1 = partition number Detailed Description The partition number identified in the message cannot be queried, because identified partition does not exist. Recommended Response Action Use a partition number of an existing partition for the requested operation.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0005 Message No vFlash partitions exist. Detailed Description There are no vFlash partitions available currently for the display. Recommended Response Action No response action is required.
Subcategory VFL = vFlash Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0009 Message vFlash media is currently in use by another operation. Detailed Description Unable to access the vFlash media, because another operation is currently using the vFlash media.
Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0011 Message vFlash media is not disabled. Detailed Description The vFlash media is not disabled. Recommended Response Action Disable the vFlash media by running the command racadm set idrac.vFlashSD.Enable 0.
Recommended Response Action Enable the vFlash media by running the command racadm set idrac.vFlashSD.Enable 1. Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0013 Message The vFlash SD Card is in read-only mode.
Detailed Description The vFlash SD card is not initialized. Either the card is not properly formatted or it may not be supported. Recommended Response Action Format the vFlash SD card by running the command "racadm vflashsd initialize". Make sure that the card is supported by contacting your service provider for a list of supported SD card types. Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
VFL0016 Message vFlash media partition is already in attached state. Detailed Description The requested vFash media partition is already attached to the host operating system. Recommended Response Action No response action is required. Category Configuration Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable VFL0018 Message The requested operation is in progress. Detailed Description The requested operation is currently in progress. Recommended Response Action Wait for the requested operation to complete. Category Configuration Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0020 Message vFlash SD card is not ready. Detailed Description The vFlash SD card is currently in use by another operation. Recommended Response Action Wait for the current vFlash SD card operation to finish, and they retry. Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0703 Message The SD card initialization was successful. Detailed Description None Recommended Response Action No response action is required. Category Configuration Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0705 Message Error occurred and SD card could not be initialized. Detailed Description An error has occurred while initializing the SD card. The SD card is not present or vFlash is not enabled, or the SD card is write-protected.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0710 Message vFlash is not enabled; the SD card could not be initialized. Detailed Description none Recommended Response Action Enable vFlash and try again. Category Configuration Subcategory VFL = vFlash Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Subcategory VFL = vFlash Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0712 Message One or more partitions are busy with another operation; the SD card could not be initialized.
Category Configuration Subcategory VFL = vFlash Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0714 Message SD card is not ready and could not be initialized. Detailed Description none Recommended Response Action Retry after a few minutes.
Recommended Response Action Contact the administrator for the required permissions and try again. Category Configuration Subcategory VFL = vFlash Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL0716 Message SD Card is not a vFlash SD Card; the SD card could not be initialized.
Detailed Description The SD card is in use by another process. Initialization requires exclusive access to the SD card to complete the initialization. Recommended Response Action The SD card is in use by another process. Retry after a few minutes. Category Configuration Subcategory VFL = vFlash Event Severity Severity 1 (Critical) LCD Message No LCD message display defined.
VFL1001 Message Arguments Removable Flash Media arg1 is present. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) Trap/EventID 2507 LCD Message No LCD message display defined.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL1003 Message Arguments Removable Flash Media arg1 is not IPMI-function ready. • arg1 = name Detailed Description The removable flash media is installed but improperly configured or failed to initialize. Recommended Response Action If unintended, reinstall the flash media and module.
Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL1005 Message Arguments Removable Flash Media arg1 is not ready. • arg1 = name Detailed Description The media is being prepared or is under maintenance. If the problem persists, reinstall the card.
Detailed Description At boot, the Card Identification (CID) signature of the card is different from the Non-volatile (NV) storage value or the card is the destination of a copy operation that is in-progress. Recommended Response Action If unintended, reinstall the flash media. Category System Health Subcategory VFL = vFlash Event Severity Severity 2 (Warning) LCD Message No LCD message display defined.
VFL1008 Message Arguments Failure detected on Removable Flash Media arg1 . • arg1 = name Detailed Description An error is reported during a SD card read or write. Recommended Response Action Re-install the flash media, if the issue persists replace the media. Category System Health Subcategory VFL = vFlash Event Severity Severity 1 (Critical) Trap/EventID 2505 LCD Message Removable Flash Media failed.
LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL1010 Message Arguments Removable Flash Media arg1 was activated. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) Trap/EventID 2507 LCD Message No LCD message display defined.
Recommended Response Action No response action is required. Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) Trap/EventID 2507 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL1012 Message Arguments Removable Flash Media arg1 is booting.
VFL1013 Message Arguments Removable Flash Media arg1 has finished booting. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL1015 Message Arguments Removable Flash Media arg1 is writable. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory VFL = vFlash Event Severity Severity 3 (Informational) Trap/EventID 2507 LCD Message No LCD message display defined.
Recommended Response Action If unintended, reinstall the flash media. Category System Health Subcategory VFL = vFlash Event Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VFL1017 Message Arguments Media is present for Removable Flash Media arg1 . • arg1 = name Detailed Description None Recommended Response Action No response action is required.
VFLA Event Messages 69 VFLA1000 Message Arguments Removable Flash Media arg1 is absent. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory VFLA = vFlash Absent Severity Severity 3 (Informational) Trap/EventID 2515 LCD Message No LCD message display defined.
VLT Event Messages 70 VLT0100 Message Arguments Processor module arg1 voltage is less than the lower warning threshold. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Remove the processor module. Inspect processor socket for bent pins.
Recommended Response Action 1) Review system logs for power supply exceptions. 2) Remove the processor module. Inspect processor socket for bent pins. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory VLT = Voltage Severity Severity 1 (Critical) LCD Message Processor module voltage is outside of range.
VLT0103 Message Arguments Processor module arg1 voltage is greater than the upper critical threshold. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Remove the processor module. Inspect processor socket for bent pins. 3) If the problem persists, contact technical support.
Trap/EventID 2169 LCD Message Processor module voltage is outside of range. Contact support Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0105 Message Arguments Processor module arg1 voltage is within range. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions 2) Reduce system to minimum configuration, inspect and re-install system cables. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0202 Message Arguments The system board arg1 voltage is greater than the upper warning threshold. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode.
Recommended Response Action 1) Review system logs for power supply exceptions 2) Reduce system to minimum configuration, inspect and re-install system cables. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory VLT = Voltage Severity Severity 1 (Critical) Trap/EventID 2169 LCD Message The system board voltage is outside of range.
Server Administrator Trap ID Not Applicable VLT0205 Message Arguments The system board arg1 voltage is within range. • arg1 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory VLT = Voltage Severity Severity 3 (Informational) Trap/EventID 2171 LCD Message No LCD message display defined.
Subcategory VLT = Voltage Severity Severity 2 (Warning) Trap/EventID 2170 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0207 Message Arguments The memory module arg1 arg2 voltage is less than the lower critical threshold. • arg1 = number • arg2 = name Detailed Description System hardware detected an over voltage or under voltage condition.
VLT0208 Message Arguments The memory module arg1 arg2 voltage is greater than the upper warning threshold. • arg1 = number • arg2 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the memory module. 3) If the problem persists, contact technical support.
Subcategory VLT = Voltage Severity Severity 1 (Critical) Trap/EventID 2169 LCD Message Memory module voltage is outside of range. Contact support Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0210 Message Arguments The memory module arg1 arg2 voltage is outside of range. • arg1 = number • arg2 = name Detailed Description System hardware detected an over voltage or under voltage condition.
VLT0211 Message Arguments The memory module arg1 arg2 voltage is within range. • arg1 = number • arg2 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory VLT = Voltage Severity Severity 3 (Informational) Trap/EventID 2171 LCD Message No LCD message display defined.
Severity Severity 2 (Warning) Trap/EventID 2170 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0213 Message Arguments The disk drive bay arg1 voltage is less than the lower critical threshold. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition.
Arguments • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat hard disks in the bay. Reconnect all cables attached to the bay. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0216 Message Arguments The disk drive bay arg1 voltage is outside of range. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions.
Recommended Response Action No response action is required. Category System Health Subcategory VLT = Voltage Severity Severity 3 (Informational) Trap/EventID 2171 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0218 Message Arguments The arg1 voltage is less than the lower warning threshold.
Server Administrator Trap ID Not Applicable VLT0219 Message Arguments The arg1 voltage is less than the lower critical threshold. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions 2) Reduce system to minimum configuration, inspect and re-install system cables.
Category System Health Subcategory VLT = Voltage Severity Severity 2 (Warning) Trap/EventID 2170 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0221 Message Arguments The arg1 voltage is greater than the upper critical threshold. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition.
VLT0222 Message Arguments The arg1 voltage is outside of range. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions 2) Reduce system to minimum configuration, inspect and re-install system cables. 3) If the problem persists, contact technical support.
Trap/EventID 2171 LCD Message No LCD message display defined. Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0224 Message Arguments The memory module arg1 voltage is less than the lower warning threshold. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode.
Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the memory module. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Server Administrator Trap ID Not Applicable VLT0227 Message Arguments The memory module arg1 voltage is greater than the upper critical threshold. • arg1 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the memory module.
Subcategory VLT = Voltage Severity Severity 1 (Critical) Trap/EventID 2169 LCD Message Memory module voltage is outside of range. Contact support Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0229 Message Arguments The memory module arg1 voltage is within range. • arg1 = name Detailed Description None Recommended Response Action No response action is required.
Arguments • arg1 = number • arg2 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the mezzanine card. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Initial Default IPMI Alert;LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0232 Message Arguments The mezzanine card arg1 arg2 voltage is greater than the upper warning threshold. • arg1 = number • arg2 = name Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode.
Detailed Description System hardware detected an over voltage or under voltage condition. If multiple voltage exceptions occur consecutively the system may power down in failsafe mode. Recommended Response Action 1) Review system logs for power supply exceptions. 2) Reseat the mezzanine card. 3) If the problem persists, contact technical support. Refer to the product documentation to choose a convenient contact method.
Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VLT0235 Message Arguments The mezzanine card arg1 arg2 voltage is within range. • arg1 = number • arg2 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory VLT = Voltage Severity Severity 3 (Informational) Trap/EventID 2171 LCD Message No LCD message display defined.
Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly. 3) If the issue still persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory VLT = Voltage Severity Severity 2 (Warning) Trap/EventID 2170 LCD Message No LCD message display defined.
Server Administrator Trap ID Not Applicable VLT0302 Message Arguments CPU arg1 arg2 voltage is greater than the upper warning threshold. • arg1 = number • arg2 = name Detailed Description High voltages may be the result of problem with the voltage regulator or a problem with the processor. Elevated voltages may result in damage to the processor or other electronic components inside the system. Recommended Response Action 1) Turn system off and remove input power for one minute.
Recommended Response Action 1) Turn system off and remove input power for one minute. Re-apply input power and turn system on. 2) Make sure the processor is seated correctly. 3) If the issue still persists, contact technical support. Refer to the product documentation to choose a convenient contact method. Category System Health Subcategory VLT = Voltage Severity Severity 1 (Critical) Trap/EventID 2169 LCD Message CPU voltage is outside of range.
Server Administrator Trap ID Not Applicable VLT0305 Message Arguments CPU arg1 arg2 voltage is within range. • arg1 = number • arg2 = name Detailed Description None Recommended Response Action No response action is required. Category System Health Subcategory VLT = Voltage Severity Severity 3 (Informational) Trap/EventID 2171 LCD Message No LCD message display defined.
board. 3) If the sensor identified is a processor voltage sensor, remove the processor module and inspect processor socket, and replace if required. If the issue persists, contact your service provider. Category System Health Subcategory VLT = Voltage Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default OS Log;None Server Administrator Event ID 5150 Server Administrator Trap ID Not Applicable VLT401 Message Arguments Unable to read arg1 sensor value.
Server Administrator Trap ID Not Applicable VLT402 Message Arguments The arg1 sensor has returned to a normal state with a value of arg2 Volts. • arg1 = sensor name • arg2 = voltage Detailed Description The voltage sensor identified in the message has returned to a normal state. Recommended Response Action No response action is required. Category System Health Subcategory VLT = Voltage Severity Severity 3 (Informational) LCD Message No LCD message display defined.
processor module and inspect processor socket, and replace if required. If the issue persists, contact your service provider. Category System Health Subcategory VLT = Voltage Severity Severity 2 (Warning) LCD Message No LCD message display defined. Initial Default SNMP Alert;OS Log;None Server Administrator Event ID 5153 Server Administrator Trap ID 5153 VLT404 Message Arguments The arg1 sensor detected an error with a value of arg2 Volts.
Server Administrator Trap ID 5154 VLT405 Message Arguments The arg1 sensor has failed with a value of arg2 Volts. • arg1 = sensor name • arg2 = voltage Detailed Description A voltage sensor identified in the message may have failed. This condition can cause system performance issues and degradation in the moitoring capability of the system. Recommended Response Action Do one of the following to resolve the issue: 1) Verify the Embedded System Management (ESM) Log for any sensor related faults.
VME Event Messages 71 VME0001 Message Virtual Console session started. Detailed Description Virtual Console session started. Recommended Response Action No response action is required. Category Audit Subcategory VME = Virtual Media Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VME0002 Message Virtual Media session started.
Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VME0003 Message Virtual Console session fails to start. Detailed Description Virtual Console session fails to start. Recommended Response Action Retry the Virtual Console session initiation. Category Audit Subcategory VME = Virtual Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VME0005 Message Virtual Console session exited. Detailed Description Virtual Console session exited. Recommended Response Action No response action is required. Category Audit Subcategory VME = Virtual Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default LC Log Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VME0007 Message Virtual Console session created. Detailed Description Virtual Console session created. Recommended Response Action No response action is required. Category Audit Subcategory VME = Virtual Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory VME = Virtual Media Severity Severity 3 (Informational) LCD Message No LCD message display defined.
VRM Event Messages 72 VRM0009 Message No Virtual Media devices are currently connected. Detailed Description No virtual media was found to disconnect. Recommended Response Action No response action is required. Category System Health Subcategory VRM = Virtual Console Severity Severity 1 (Critical) LCD Message No LCD message display defined.
Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VRM0011 Message The Virtual Media image server is not currently connected. Detailed Description The Virtual Media server is already disconnected. Recommended Response Action No response action is required. Category System Health Subcategory VRM = Virtual Console Severity Severity 3 (Informational) LCD Message No LCD message display defined.
LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VRM0013 Message Virtual Media services is currently attached to the USB interface.\nIt must be detached before the image server can be connected. Detailed Description Simultaneously connecting Virtual Media and USB interface is not possible. Recommended Response Action Detach the USB interface and re-try.
Severity Severity 1 (Critical) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VRM0015 Message Virtual Console is ENABLED Detailed Description Success message. Recommended Response Action No response action is required. Category Configuration Subcategory VRM = Virtual Console Severity Severity 3 (Informational) LCD Message No LCD message display defined.
Subcategory VRM = Virtual Console Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VRM0017 Message Virtual Media disconnect operation successful Detailed Description Success message. Recommended Response Action No response action is required.
Category Configuration Subcategory VRM = Virtual Console Severity Severity 3 (Informational) LCD Message No LCD message display defined. Initial Default None Server Administrator Event ID Not Applicable Server Administrator Trap ID Not Applicable VRM0019 Message Remote Image is now Configured Detailed Description The Remote Image is now configured and ready to use. Recommended Response Action No response action is required.
Recommended Response Action No response action is required. Category System Health Subcategory VRM = Virtual Console Severity Severity 1 (Critical) LCD Message No LCD message display defined.
