Installation Guide

ManualsBrandsDefiant ManualsDeadboltsSingle Cylinder Satin Nickel Square Spin-To-Lock Electronic Deadbolt

WARRANTY

CAUTION:

Please use four alkaline batteries for the best performance.

CARE and MAINTENANCE:

The following instructions should be followed to properly protect and maintain your lockset:

Read the precautions and instructions in this manual before installing and using this lock. Save this manual for future reference.

A. Remove locks, or do not install locks, prior to painting your door.

B. Periodically clean with mild soap and a soft cloth only.

C. Do not use any abrasives or chemical products containing alcohol, benzene, acids, and avoid using sharp or abrasive objects to clean this lockset.

D. Do not allow any water or liquids into the lockset during installation.

A. Do not attempt to disassemble any internal components of the lockset. Doing so will void the limited warranty.

B. Do not drop or hit the lockset. Too much shock may result in permanent damage.

C. Do not use pins or sharp objects to press the keypad.

D. Always create a backup of information you wish to keep (master code, user codes,etc.) Please use the last page of this booklet as a reference.

E. Be sure to complete initial settings before operating lockset.

Safety Information

WARNING:

If the door needs to be drilled, please be familiar with how to use a drill safely and understand all of the door preparation steps before proceeding.

Do not use a drill to assemble this product.

Pre-installation – Tools Required / Hardware Included

Installation

Optional Optional Optional Optional Optional



Cut out TEMPLATE (reverse page) and use to mark the door, drill holes, and chisel out the mortise.

NOTE: Drill from both sides of the door to prevent wood splitting.

Pre-installation (continued) – Door Preparation

(25 mm)

2-1/8"(54 mm)

1-1/2"(38 mm)

Backset

Centerline

Note: For drive-in latch.

Simply insert latch.

Outline

Chisel 5/32" (3 mm) deep

Faceplate

NOTE: If your door is pre-drilled, check the hole sizes to make sure they are the proper size. If they are the proper size, skip to the INSTALLATION section.

Dust box

Strike plate

Prepare the door jamb – use the strike plate as a template to drill the latch and screw holes and chisel out the mortise. The strike plate must fit flush with the surface

of the door jamb.



Door jamb hole dimension

Strike dimentions

b. 1-9/64"(29 mm)

d. 5/32"(4 mm)

e. 2-1/4"(57 mm)

f. 1"(25 mm)

a. 1-3/16"(30 mm)

c. 7/8"(22 mm)

A. Attach the correct faceplate

B. Set the latch backset length

C. Install the latch



INSTALLING THE LATCH

CAUTION: Be sure the latch cam is upright before making any backset adjustment.

Edge of door

Faceplate

Edge of door

Drive-in

collar

Flat head screwdriver

Remove the Battery Cover

INSTALLING THE LOCK ASSEMBLIES



A. Door bore options

LIMITED LIFETIME MECHANICAL AND 1 YEAR ELECTRONIC WARRANTY

The retailer of this product, hereby warrants, subject to the conditions set forth below, that it will either repair or replace, at its option, this product if it

proves to be defective by reason of improper workmanship or materials within the original purchaser's limited time. In order to obtain repairs or

replacement under this limited warranty you must bring this product to the retailer's store in which you bought it.

Original purchaser: This limited warranty is limited to the original purchaser at retail of this product from retailer.

Except to the extent prohibited by applicable law, no other warranties, whether express or implied, including the warranties of merchantability and ﬁtness

for a particular purpose, shall apply to this product. Under no circumstances shall retailer be liable for consequential or incidental damages in connection

with this product. To the extent retailer is prohibited by applicable law from excluding implied warranties, the duration of such implied warranties which

are not excludable shall be the original purchaser's lifetime. Some states do not allow the limitation on how long an implied warranty lasts, so the above

limitation on the duration of implied warranties which are not excludable, if any, may not apply to you. Some states do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation or exclusion of incidental or consequential damages may not apply to you.

Retailer neither assumes not authorizes any representative or other person to assume for it any obligation or liability other than such as is expressly set

forth herein. This limited warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state.

FOR

G32-KPDDB512 Rev. 17/09-02

Retract the latch bolt.

Thread the cable through

the hole and under the latch.

For installation into 1-1/2"(38mm) bore hole,

simply pry the adapter collar off with a

screwdriver.

Adapter collar

The bulged part of the mounting

plate must face towards the door.

B. Install the lock assemblies

Slide the cable

through the notch

in mounting plate.

Assemble the wire

and arrange the

remaining parts of

wire in the door hole.

Insert screws and tighten



(

)



180º



(

)

Backset

Wood block (not included)

Drive-in latch

Tap latch ﬂush

PACKAGE CONTENTS LIST

Exterior Assembly

Power Cable

D Torque Blade

E Exterior Gasket

F Adapter collar

G Mounting Plate

I Battery Cover

H Interior Assembly

J Latch

K Radius Faceplate

L Drive-in Collar (Optional)

M Strike Plate

N Dust Box

Key

HARDWARE CONTENTS

2-5/16" (58 mm) Mounting Bolt Qty. 2

7/16" (11mm) Screw Qty. 2

3/4" (19 mm) Wood Screw Qty. 2

2" (51 mm) Wood screws Qty. 2

2 " (51 mm) Wood screws Qty. 2

Hardware Used

3/4" (19 mm) Latch screws Qty. 2

Hardware Used

Your latch is set for 2-3/8"(60mm) backset. It can be adjusted if needed to 2-3/4"(70mm) (skip this if your door has a 2-3/8"(60mm) backset).

Install three AAA alkaline batteries

https://goo.gl/SpxXwt

SCAN FOR

INSTALLATION

2-1/8"(54 mm)

1-1/2"(38 mm)

Press

Connect the cable

ﬁrmly into connector

port .

Note : The connector side with solder

joints should face outward.

Install battery cover

Install batteries

AAA

CAUTION :

1.Please use three alkaline batteries for better performance.

Be sure to insert them correctly by matching the + and – polarity markings.

Do not mix old batteries and new batteries or standard (carbon-zinc) with alkaline batteries.

2.Please activate the lockset by entering the DEFAULT MASTER CODE (123456) to ﬁnish installation.

3.Install and test lock with door OPENED to avoid being locked out.

Enter the default Master Code (123456) to

activate your lockset and complete installation.

Questions, problems, missing parts? Before returning to the store,

call Deﬁant Customer Service

TOLL FREE HELP LINE 1-877-ONE-LOCK

HOMEDEPOT.COM

08:30 a.m.-05:30 p.m., EST, Monday - Friday

Depth of latch hole

25 mm

(1 ")

For 2-3/8

"(60mm)

backset: 3-7/16

"(87mm)

For 2-3/4

"(70mm)

backset: 3-13/16

"(97mm)

Summary of content (2 pages)

PAGE 1
G32-KPDDB512 Rev. 17/09-02 3 Pre-installation (continued) – Door Preparation NOTE: If your door is pre-drilled, check the hole sizes to make sure they are the proper size. If they are the proper size, skip to the INSTALLATION section. FOR Cut out TEMPLATE (reverse page) and use to mark the door, drill holes, and chisel out the mortise. NOTE: Drill from both sides of the door to prevent wood splitting.
PAGE 2
SCAN FOR PROGRAMMING PROGRAMMING https://goo.gl/SpxXwt 1 HOW TO LOCK / UNLOCK OVERVIEW OF THE LOCKSET Please activate the lockset by entering the DEFAULT MASTER CODE(123456) before the following operation. BUTTON ENTER 1. Red light: Represents an incorrect entry. 2. Yellow light: Flashes when the batteries are low in power or the unit is programming mode. 3. Green light: Represents a correct entry. 4. Press for 2 seconds to enter programming mode. OR To lock KEYPAD 1.