cacor Installation The Life of the Kitchen® Instructions Millennia® Wall Mount Range Hoods Models: DHW301, DHW361, DHW421 APPROVED Part No. 101743 Rev. F and DHW482 FOR USE WITH ALL DACOR® RANGES AND COOKTOPS.
Table of Contents Important Safety Instructions ............ccccccsssssceeceeeeeees Important Information About Safety Instructions......... General Safety Precautions ............ cc ccccecececeeeeeeeees Installation Specifications .........ccccccsccceeeeeessesseeeeenees Performance Specifications ..............ccccccceccccceeeeeeeeees Electrical Specifications ...........cccccccscccceeeeeessessesseeeeenees DIMENSIONS ......... ccc cccccccccccsnececcecnseeececcneeeeecenseeeeeeenaes Planning the Location ..
Important Safety Instructions Important Information About Safety Symbols and Labels Safety Instructions = DANGER The Important Safety Instructions and warnings in Immediate hazards.that WILL result-in severe. personal these instructions are not meant to cover all possible __| injury or death. problems and conditions that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance.
Important Safety Instructions General Safety Precautions To reduce the risk of fire, electric shock, serious injury or death when ty precautions, including the following: using your appliance, follow basic safe- WARNING ¢._ If-the-information in this manual is not followed exactly, a fire or explosion may result causing property. damage, personal injury.or death. «-.Do not install or operate this hood if it has been damaged, dropped, has damaged electrical wires or.is not working properly.
Installation Specifications Performance Specifications Dimensions All Models Tolerances: +1/16” (41.6 mm), -0 unless otherwise stated 600 CFM* Blower 11 3/4” — at (for single blower units) 1200 CFM* (for dual blower units) Blower Speeds | 4 with electronic speed control Lights 12 Vac, 20 Watt halogen Filters Baffle type, dishwasher safe Exhaust 8-inch Total Connected | 120 Vac, 60 Hz. Load (See table below for current draw) Circuit Requirement 120 Vac, 15 Amp.
Installation Specifications Planning and Installing the Duct Work WARNING *-To.prevent-combustion by-products, smoke.or odors from entering the home and to improve efficiency, tape.all duct joints securely. «--Use-only duct work deemed. acceptable by-state, municipal and local codes. «--DO.NOT install an additional in-line or external blower to increase the length of the duct.run..Even small differences between blower-air flow rates can greatly reduce the.air-draw-of the hood.
Installation Instructions WARNING «Observe. all governing codes and ordinances during installation.:Contact your local building department for further information. «A qualified technician must complete the installation of this built-in appliance. The owner.is. responsible to make sure the hood is properly installed. «Do not install the range hood unless the power-supply provided ‘meets. the required Electrical Specifications (see page 3). «To avoid an electric shock hazard and property.
Installation Instructions Installing the Mounting Bracket If mounting the hood to drywall: the hood mount- e ing location on : ot “N six inch vertical line that intersects ee 1 et ie / Hood center ; line . ' the line drawn in step 2. ' : : : : : 1:. Make sure the mounting location is properly reinforced so that it will hold the weight of the hood. eat ~~' : : : ' : Height of mounting bracket
Installation Ha 1. ng ng the Ra nge Hood Instructions 6. Attach the hood junction box to the top of the hood On models with two blowers: Put the exhaust cowling over the blower outlets on the top of the hood. Fasten the cowling in place with 14 machine screws. using two machine screws as shown. e boy 2. Remove the filter(s) to reduce weight and avoid damage. 3. Lift the hood up on both sides and put the mounting hole on the top of the hood over the lip of the mounting bracket.
Installation Instructions Connecting the Duct Work Final Chimney Assembly WARNING Do not-use. screws to attach the duct work to the hood exhaust outlet::Use.duct tape only. Screws may. prevent the damper flaps on the top of the hood from opening. WARNING Be careful not:to pinch the electrical wires while assembling the chimney. 1. Install the duct work between the hood exhaust and the previously installed duct work. Attach the duct to the hood exhaust with duct tape alone.
Installation 4. Carefully put the chimney over the top of the duct work extending out of the top of the hood, taking care not to scratch the surfaces. Make sure the wiring is tucked in behind the chimney. Instructions Installation Checklist WARNING Move the chimney up toward the ceiling. Line up the holes on the side of the chimney, above the vents, with the holes on the side of the chimney mounting bracket. To ensure a safe and proper installation, the following checklist. should be.
Wiring Diagrams © © YELLOW/GREEN 120V Tm , 3 t CN2 CN3 = : : ;Peecccecvon] _CN2 rcs © ™ 2 12 =Zz CN1 ~~ loood ©= CN4 ep 8 CN1 oD Oo o CNS MAIN POWER SWITCH TRANSFORMER _-_—- LUV Qs LIGHT FIXTURES Wl ZOV. FU aT CNS TRANSFORMER 12V VAANAY ILYN YY, LJ a CN1 FS LIGHT FIXTURES EXTERNAL BLOWER CONNECTION §&. oo \\ n t Single Blower Models: DHW301, DHW361, DHW421 cacor.
Wiring Diagrams el SS © 3 \ 120V 60Hz YELLOW/GREEN MAIN POWER SWITCH MOTOR © \\ 2 \t CNB TO BLOWER woToR ial pa t a = CN2 CN3 Peceescesood CN1 NE TL, ong —— = Ne oe M4 i HLL E= CNI eo CN6 CNZ ONS ae | CN9 LIGHT FIXTURES S| TRANSFORMER LIGHT FIXTURES HONOL TRANSFORMER — — TOULNOD LUN CN4 = = 7 = — <= => = => => = => = ff CN1 CN2 Je CN2 -Ty EXTERNAL BLOWER CONNECTION ae CN1 Please note—the layout on the PC Board shown above may vary— however all wires ar
12 cdacor.
cacor The Life of the Kitchen? Dacor e 600 Anton Bivd. Suite 1000 Costa Mesa, CA 92626 « Phone: (800) 793-0093 e Fax: (626) 403-3130 « www.Dacor.
