Installation Guide

ManualsBrandsCoway ManualsBathBidetmega 400 Electric Bidet Seat for Elongated Toilets in White

Installation

During installation

Firmly fix the fixing nuts so that the product is not loosened from the toilet.

Installation position

The bidet is a product installed inside a bathroom, so make sure to choose a spot where water does not

splash on the product.

After installation

Avoid direct sunlight to prevent damages to the toilet seat.

Cold water pipe

Make sure to connect it to the cold water pipe.

(If connected to the hot water pipe, the filters and hoses can get damaged.)

When installing a remote controller

Install the remote controller next to the bidet.

Before attaching double-sided tapes on the remote controller holder, make sure to remove dust and foreign

substances from the surface.

How to replace remote controller battery

Insert a coin or driver into the groove and turn it CCW to make one turn, then the screws will be loosened

and the battery cover will be removed.

Then, replace the batteries (1.5 V AAA, 3 batteries) and fix the screws again.

Turn the screw CW to seal the hole.

Be careful not to lose the screws by mistake.

NOTE



Consult with a Coway technician for the detailed installation method to ensure optimal performance of the product.

- Service center : 1-800-285-0982

Be Careful!

03 MAINTENANCE

Summary of content (6 pages)

PAGE 1
03 MAINTENANCE Installation Be Careful! During installation Firmly fix the fixing nuts so that the product is not loosened from the toilet. Installation position The bidet is a product installed inside a bathroom, so make sure to choose a spot where water does not splash on the product. After installation Avoid direct sunlight to prevent damages to the toilet seat. Cold water pipe Make sure to connect it to the cold water pipe.
PAGE 2
Remove existing toilet seat emove the existing toilet seat ❶ and R seat cover ❷ by removing the fixing nuts. EN 1 N OTE 2 eep the removed toilet seat in a shaded location to K prevent it from being damaged. 1 Install product NOTE As the bidet should be installed on the toilet, ensure that water is not splashed onto the bidet. 2 1 Turn off the main water supply valve ❶ and separate the existing water tank hose ❷.
PAGE 3
03 MAINTENANCE Installation Install product Toilet tank Conversion bolt (with packing) T-shaped connector (with packing) 2-2 Conversion nut (with packing) Cold water supply line Please connect the T-shaped connector or T-shaped connector with ½” conversion bolt and nut to the water supply pipe first. If the water supply pipe does not fit or the pipe type is rigid, please connect the 7/8” conversion bolt and nut to the 3/8” T-shaped connector as you can see in the image.
PAGE 4
Connect the bidet hose to the side of the bidet. Make sure that the bidet hose is firmly connected. If the main water supply valve is opened when the hose is not connected properly, the bidet hose may become separated and cause water to splash, resulting in injury. EN 5 살균 D ANGER ake care that the bidet hose is not excessively bent by T twisting it. 6 Grounding Pin 7 Open the main water supply valve. Connect the power cord to the electrical outlet.
PAGE 5
03 MAINTENANCE Installation Install remote controller 1 2 Before attaching the bracket, thoroughly wipe the attachment areas with a dry cloth. * If there is water left on it, its adhesion power may be degraded. Depending on the wall type, you can install using the supplied screws and anchor mounts or use the provided double stick tape on the back of the remote wall mount. Make sure the remote mount is fully secured with either method so that it does not fall and damage the remote control.
PAGE 6
Cautions for keeping remote controller * I f you slide the remote controller into the holder from the top to the bottom, it can cause falling or damage of the remote controller. EN Example of correct use Example of incorrect use Caution for falling of the remote controller : When mounting the remote controller, make sure to push it in from the front to the rear. s shown in the figure, push the remote controller into the holder to *A insert it firmly.