Diamond PD - Power Drive Rolling Door Opener Instruction Manual N1854 Manufacturer’s Part # 79078 (Manual) B&D Doors is a Division of B&D Australia Pty Ltd ABN 25 010 473 971 www.bnd.com.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Diamond PD - Power Drive Rolling Door Opener Safety Rules 03 System Specification 04 About Your B&D Opener 05 Operating Controls 06 Kit Contents 07 Installation & Setup 08 Pre-Installation Requirements 08 Installation 09 Setting Travel Limits 12 Resetting Travel Limits 12 Coding Transmitters 13 Safety Test 15 Accessories 16 Safety Infra-red Beam 16 Electric Key Witch 16 Remote Aerial 17 Terminal Black 17 How
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Safety Rules Please read these important safety rules These safety alert symbols indicate a personal safety or property damage instruction exists. READ THESE INSTRUCTIONS CAREFULLY. This automatic garage door opener is designed and tested to offer safe service provided it is installed and operated in strict accordance with the following safety rules.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Default Settings & Specifications Factory Default Settings Default Step Maximum Courtesy light time 3 min (approx.) - - Obstruction force margin 2 1 11 Auto-close time 30 sec - - Technical Specifications Mains 230-240V AC, 50Hz Standby power 2.2 Watts Rated input power 240 Watts Motor type 24V DC Permanent Magnet Maximum door size 14.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual About Your B&D Opener Thank you for choosing a B&D automatic garage door opener. This automatic garage door opener has been designed and developed in Australia by B&D Doors.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Operating Controls 16 01 02 15 14 LT01-1.00 LT01-1.00 6 03 + - + - 04 13 05 12 11 06 10 07 09 08 17 01. 02. 03. 04. 05. 06. 07. 08. 09. 10. Fuse Terminal block LED light Module LT01 Antenna terminal SERVICE LED indicator (yellow) OPERATE button (blue) LIMIT SET button (black) FORCE MARGIN SET button CODE SET LED indicator (red) MINUS (-) and CODE SET button (red) 11. CLOSE LIMIT LED indicator (red) 12.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Kit Contents $IAMOND 0$ 0OWER $RIVE )NSTRUCTION -ANUAL N1854 0 . XXXX 1. 1. 2. 3. 4. 2. 3. " $ $OORS IS A $IVISION OF " $ !USTRALIA 0TY ,TD !". 4. Powerhead Weight Bar Instruction manual and warning labels Installation and Operating Items, including: a. Qty 2 Keyring remote control transmitters b. Qty 2 Screw M4 x 50 c. Qty 2 3/16x1/2 flat washers d. Qty 2 5/32 shakeproof washer e. Qty 2 Nut M4 hex f.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Pre-Installation Requirements WARNING! Incorrect installation can lead to severe injury - FOLLOW ALL INSTALLATION INSTRUCTIONS. Door Operation Fig.01 The door must be in good operating condition. The maximum effort to move the door up or down, from stationary, should not exceed 200 Newtons (20kg force) at the bottom rail. The recommended force is 70N (7kg) for manual operation. Lift the door to about halfway.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual 9 Installation Step 1 - Preparation a. b. Check the door’s operation: i. The door must travel smoothly and be easy to operate by hand. ii. Operating force on the bottom rail should be approximately 70N (7kgs) force. iii. Adjust any tight or twisted guides/tracks iv. Clean the guides if there is any oil or wax present using a suitable white spirit. The only lubricant suitable for use on door guides is silicon spray.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Installation Step 3 - Pin the Door Curtain Door drum Pinning the door curtain to the door drum maintains security when the opener closes and locks. Pin Points Fig.07 a. b. c. d. Fully close the door. Mark drill holes at both ends of the drum (Fig. 07). Drill holes using 3.2mm (1/8”) drill bit. Open the door slightly for easier access, if necessary. Fit a 10 x 32mm screw and washer to each end.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual 11 Installation WARNING! The opener should not be installed where the door opens over a public footpath or roadway. M6 x 45 Hex Screw Washer 6.4 x 20 x 1.6 Extension Fork Fig.09 Step 5 - Assemble the Internal Gear a. b. Insert the two forks into the ring gear (Fig. 09). Secure with M6x45 hex serration head screw and washer. Step 6 - Mounting the Opener a. b. c. d. e.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual 12 Setting Travel Limits Step 7.1 - Setting Travel Limits NOTE: If Infra-red Safety Beams are to be used they must be installed before setting the travel limits. Fig.12 WARNING! Use caution when operating the manual release with the door open since it may fall rapidly due to weak or broken springs, or an improperly balanced door.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual 13 Coding Transmitters Step 8.1 - Storing the Transmitter Code The opener can only operated from remote control transmitters that have been programmed into its memory. Up to fourteen (14) codes can be stored in the memory. a. b. c. d. e. Ensure that the battery is inserted in the transmitter. Press the CODE SET button and release. The CODE SET LED will illuminate to indicate the opener is in Code Learn mode.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual 14 Coding Transmitters Step 8.4 - Setting the Transmitter to Operate the Auxiliary Output It is possible to operate other devices (e.g. alarm systems) using one of the spare buttons of a multi-channel transmitter coded into the Auxiliary Output feature. Fig.16 Press CODE SET button four times a. b. Select one of the four buttons (not programmed yet ) you wish to use to control the auxiliary output c. Press CODE SET button four times.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual 15 Safety Obstruction Force Test Step 9.1 - Door Closing Test a. b. c. d. e. Ensure that the door is open. Place a 40mm obstacle flat on the floor under the middle of the garage door (Fig. 20). Operate the door in the close direction; the door must reverse on hitting the obstruction. The CLOSE LIMIT LED flashes to indicate an obstruction while closing.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual 16 Adjusting Safety Obstruction Force Adjusting Safety Obstruction Force Fig. 21 The Safety Obstruction Force is calculated automatically and set in the memory on the opener during setup. It is usually not necessary to adjust the Safety Obstruction Force. The only time the force may need to be increased is due to environmental conditions, for example, windy or dusty areas, and areas with extreme temperature changes.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Accessories RECEIVER Safety Infra-red Beam (Part No 062734) TRANSMITTER 12V For ADDITIONAL PR OTE CTION B &D Doors STR ONGLY recommend the fitting of a Safety Infra-red B eam. In most countries Safety Infra-red B eams are mandatory on all garage doors fitted with automatic openers. For a small additional outlay, B &D recommends that Safety Infra-red B eams be installed with the automatic opener ensuring additional safety and peace of mind.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Accessories LT01-1.00 Remote Aerial (Part No 062177) Some sites cause poor radio reception. Particularly problematic areas are those where there is a large amount of metal, like an all steel garage, or an underground car park with large masses of steel reinforced concrete. These issues, and others, can create radio reception issues. + - Poor radio reception will be noticed by a reduction in the operating range of the transmitters. Fig.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual How To Use Your Opener For maximum efficiency of your opener, your garage door must be in good operating condition. Fig.28 The door should be serviced annually by a Authorised Dealer (refer to Warranty conditions on page 27). WARNING! Activate the opener only when the door is in full view, free of obstructions and with the opener properly adjusted. No one should enter or leave the garage while the door is in motion.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual How To Use Your Opener Inbuilt Locking Facility DO NOT lock your door with the locking bars when your opener is engaged. This opener has an inbuilt locking facility. With the opener engaged your door will be locked whether the power is on or off. Manual Door Operation CAUTION! When operating the manual release while the door is open it may fall rapidly due to weak or broken springs, or due to it being improperly balanced. Fig.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual How To Use Your Opener Safety Infra-Red Beam Option A Safety Infra-Red Beam Kit (Part No 062153) may be fitted to this opener. • When this option is fitted, the operation of this device is such that if an object (i.e. car, child, etc.) blocks the Infra-Red beam, then the garage door opener will not close the door automatically.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Optional Accessories There is a range of additional accessories for your added convenience and security. • Safety Infra-red Beams - Part No 062734. Gives additional protection if the door is closing onto your property or person. Simply breaking the beam “stops” the door! Must be fitted if the Auto-Close feature is operational. • Keyring Transmitter - Part No 062731. Ideal for personal use when entry into the house may be via the garage.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Maintenance Maintenance The SERVICE LED will indicate the requirement for a service and/or adjustment. To reset the SERVICE LED when the door is serviced, reprogram the Door Travel Limits and the Door Travel Force – on completion of this programming the SERVICE LED will go out. Whilst your opener does not require any periodic maintenance, the door that it is fitted to does.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual 24 Troubleshooting guide Symptom Possible cause Remedy The opener does not work from the hand remote control transmitter Garage door in poor condition e.g. springs may be broken Check the door for normal operation – see monthly maintenance. Manual door lock engaged Disengage door locks The opener does not have power Plug a device e.g. a lamp, into the power point and check that it is OK.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Spare Parts © Copyright January 2008 B&D Doors Diamond PD Power Drive : Instruction Manual 25
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Warranty 1. Definitions ‘B&D’ means (a) in Australia - B&D Doors of 17 Oasis Court, Clontarf, Queensland, 4019, a division of B&D Australia Pty Ltd (ABN 25 010 473 971), or (b) in New Zealand - B&D Doors NZ Ltd of 70 Allens Road East Tamaki Auckland, which is a subsidiary of B&D Australia Pty Ltd. ‘Purchaser’ means the purchaser of the Opener.
Controll-A-Door ® Diamond PD - Power Drive Instruction Manual Warranty 9. Subject to paragraph 12 hereof; (i) the obligations of B&D under this warranty are limited to those contained herein and such warranties are expressly in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular purpose and notwithstanding any course of dealing between the parties or custom and usage in the trade to the contrary.
QLD Office: 17 Oasis Court, Clontarf 4019. Ph: (07) 3883 0200 NSW Office: 34-36 Marigold St, Revesby 2212. Ph: (02) 9722 5555 VIC/TAS Office: 147-153 Canterbury Road, Kilsyth 3137. Ph: (03) 9237 7766 SA Office: 23 Frederick Road, Royal Park 5014. Ph: (08) 8440 4747 WA Office: 96 Mulgul Drive, Malaga 6062. www.bnd.com.au Ph: (08) 9247 8777 NZ Office: 70 Allens Road, East Tamaki, Auckland. www.bnd.co.
