www.cnbtec.com XPEED Indoor Series Ver 1.
XPEED Indoor Series WWW.CNBTEC.COM This lightning flash with arrowhead symbol is intended to alert The user to the presence of un-insulated “dangerous voltage” Within the product’s enclosure that may be of sufficient magnitude To constitute a risk of electric shock to persons. This exclamation point symbol is intended to alert the user to The presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
XPEED Indoor Series ~ WWW.CNBTEC.COM Table of Contents 1. Introduction Features 4 Product & Accessories 5 Parts Name & Functions 6 2. Installation Dip Switch Setup Installation Using the Wall Mount 8 10 Installation Using the Pendant Mount 11 Wire Connections 14 3. Operation Check Points before Operation 16 Preset and Pattern Function Pre-Check 16 Starting OSD Menu 16 Reserved Preset 16 Preset 17 Swing 17 Pattern 17 Group 18 Other Functions 18 4.
XPEED Indoor Series WWW.CNBTEC.COM 1. Introduction ~ Features Camera Specifications • Image Pick-up Device: 1/4" Interline Transfer CCD • Zoom Magnification: 26x Optical Zoom, 12x Digital Zoom (Max. 312x Zoom) → Model S1465N(P)X 27x Optical Zoom, 10x Digital Zoom (Max. 270x Zoom) → Model SBN-22Z27F /SBN-23Z27F 36x Optical Zoom, 12x Digital Zoom (Max.
XPEED Indoor Series Also idealistic mechanical design protects camera from water and dust. (IP 66) • It is easy to install and maintain camera with terminal for cable connection in brackets. 1. Introduction ⊙ Product & Accessories ■ Basic Components ■ Other Components (available to be ordered separately) 5 WWW.CNBTEC.
XPEED Indoor Series WWW.CNBTEC.COM 1. Introduction ⊙ Parts Name & Functions ① Bubble If the bubble is damaged or soiled by scratching or foreign matters, the damaged/dirty part will be visible on the screen. Therefore, do not undo the protective cover until the installation is complete. ② Mounting Base The mounting base is to used to install the camera onto the ceiling or camera brackets.
XPEED Indoor Series 1. Introduction ⊙ Disassembling the Mounting Base ⊙ Assembling the Mounting Base 7 WWW.CNBTEC.
XPEED Indoor Series 2. WWW.CNBTEC.COM Installation 9 Before installing the camera, you should set the DIP switches to configure the camera ID, communication protocol. Do not use the system upgrade terminal. ~ DIP Switch Setup ■ Camera ID Setup • ID number of camera is set using binary number. The example is shown below.
XPEED Indoor Series WWW.CNBTEC.COM • If you want to control using DVR or P/T controller, their protocol must be identical to camera. Otherwise, you cannot control the camera. • It you changed camera protocol by changing DIP S/W, the change will be effective after you reboot the camera. • Factory default of protocol is “Pelco-D, 2400bps”. ■ Input Sensor Active Type • When a sensor input is used, its functional type should be set. There are two types; Normal Open type and Normal Close type.
XPEED Indoor Series 2. ⊙ WWW.CNBTEC.
XPEED Indoor Series 2. Installation ⊙ Installation Using the Pendant Mount 11 WWW.CNBTEC.
XPEED Indoor Series WWW.CNBTEC.COM 2.
XPEED Indoor Series 2. Installation ⊙ Installation using the Wall Mount 13 WWW.CNBTEC.
XPEED Indoor Series 2. WWW.CNBTEC.COM Installation ⊙ Wire Connections ■ Power Connection • The standard power for the system is 24VAC / 2A. Please, check the voltage and current capacity of rated power carefully. ■ Video Connection • Connect With BNC coaxial cable. ■ RS-485 Communication • For PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same time, RS-485 communication lines of them is connected in parallel as shown below.
XPEED Indoor Series 2. WWW.CNBTEC.COM Installation ■ Sensor Input/Relay Output • Sensor input connection Before connecting sensors, check driving voltage and output signal type of the sensor. Since output signal types of the sensors are divided into Open Collector and Voltage Output type in general, the cabling must be done properly after considering these types. Also, the sensor type, i.e. “Normal Open” or “Normal Close” in DIP switch in main body of camera must be set properly.
XPEED Indoor Series WWW.CNBTEC.COM 3. Operation ⊙ Check Points before Operation • Before power is applied, please check the cables carefully. • The camera ID of the controller must be identical to that of the target camera. The camera ID can be checked by reading DIP switches of the camera. • If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.
XPEED Indoor Series WWW.CNBTEC.COM 3. Operation ⊙ Preset • Function Max. 127 positions can be stored as Preset position. The Preset number can be assigned from 1 to 128, but 95 is reserved for starting OSD menu. Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently for each preset. Label should be blank and Relay Outputs should be set to OFF as default. “Camera Adjust” should be set “GLOBAL” as default. All characteristics can be set up in OSD menu.
XPEED Indoor Series WWW.CNBTEC.COM 3. Operation ⊙ Group • Function The group function allows running sequence of Presets, Pattern and/or Swings. Max. 8 group can be stored. Each group can have max. 20 action entities which can be preset, pattern or swing. Preset speed can be set up and the repeat number of pattern & Swing can be set up in Group setup. Dwell time between actions can be set up also. • Setting Group Use OSD Menu to create a Group. • Run Group 1) [Group No.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ OSD Display of Main Screen • P/T/Z Information Current Pan/Tilt angle in degree, zoom magnification and a compass direction. • Camera ID Current Camera ID (Address). • Action Title • Preset Label • Alarm Information Followings are possible Action Titles and their meaning.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ General Rules of key Operation for Menu • The menu items surrounded with < > always has its sub menu. • For all menu level, to go into sub menu, press NEAR key. • To go to up-one-level menu, press FAR key. • To move from items to item in the menu, use joystick in the Up/Down or Left/Right. • To change a value of an item, use Up/Down of the joystick in the controller. • Press NEAR key to save values and Press FAR key to cancel values.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ Privacy Zone Mask Setup Select area in image to mask. • MASK NO [1~8] Select Mask number. If the selected mask has already data, camera moves as it was set. Otherwise, “UNDEFINED” will be displayed under “MASK NO”. • DISPLAY [ON/OFF] Sets if camera makes mask shows or not on images. • CLEAR MASK [CANCEL/OK] Deletes data in the selected mask NO. ■ Privacy Zone Area Setup Move camera to the area to mask.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ Camera Setup ( Model SBN-22Z27F /SBN-23Z27F) Setup the general functions of 27x optical zoom camera module. • FOCUS MODE [AUTO/MANUAL/SEMIAUTO] Sets camera focus mode. • MAX ZOOM [x1 ~ x270] Sets the maximum zoom magnification. • FLICKERLESS [ON/OFF] When an NTSC camera if used under 50Hz and PAL under 60Hz flickering may appear on the screen. When this happens, turn FLICKERLESS setting ON.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ■ AUTO EXPOSURE SETUP • BACKLIGHT [OFF/C1/C2/L1/L2/U1/U2/D1/D2/R1/R2] Sets Backlight Compensation. The reference position and the level of BLC are selectable. Refer to the table below. Note1) • DAY/NIGHT [AUTO/DAY/NIGHT] • SLOW SHUTTER [OFF/2~128 Field] Activates SLOW SHUTTER function when luminance of image(signal) is too dark. It is possible to set up the maximum number of fields piled up one on another by SLOW SHUTTER function.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ Camera Setup ( Models S1465N(P)X, S1965N(P)X) Setup the general functions of 26x / 36x optical zoom modules. • FOCUS MODE [AUTO/MANUAL/SEMIAUTO] Sets camera focus mode. • DIGITAL ZOOM [ON/OFF] Sets digital zoom on or off. • FLICKERLESS [ON/OFF] When an NTSC camera is used under 50Hz or PAL under 60Hz, flickering may appear on the screen. When this happens, turn Flickerlees setting ON.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ■ AUTO EXPOSURE SETUP • BACKLIGHT [ON/OFF/WDR/A-WDR] Sets Backlight Compensation. A-WDR function is switching WDR automatically. ( A-WDR: only S1465N(P)X, S1965N(P)X models) • DAY/NIGHT [AUTO/DAY/NIGHT] • AE MODE [AUTO/SHUTTER/IRIS/GAIN/BRIGHT/MANUAL] Selects automatic exposure mode. Each mode appears with adjustable values. When Flickerless mode is ON, AE mode is automatically in SHUTTER SPEED mode. • IRIS LEVEL [CLOSE/F1.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ~ Camera Setup (SBB-22(3)Z36F model) • . Setup the general functions of 36x optical zoom modules • FOCUS MODE • MAX ZOOM • LINE LOCK [AUTO/MANUAL/SEMIAUTO] Sets camera focus mode. [x1 ~ x432] Sets the maximum zoom magnification. [ON/OFF] If Line lock sync is ON, video signal is synchronized with AC power. Video can be fluctuated after setting is changed. • COLOR [ON/OFF] Switching color mode to black-white mode.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ■ AUTO EXPOSURE SETUP • BACKLIGHT [OFF/BLC/WDR/ECL] - BLC : Back light compensation - WDR: Wide Dynamic Range Processing - ECL : Eclipses. This masks off the brightest spot. • DAY/NIGHT [AUTO/DAY/NIGHT] - AUTO : Automatic Day/Night switching. In AUTO Mode, a light level for switching can be selected. The higher sensitivity level causes the switching at lower light level.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ Motion Setup Setup the general functions of Pan/Tilt motions. • MOTION LOCK [ON/OFF] If Motion Lock is set to ON, it is impossible to set up and delete Preset Swing, Pattern and Group. It is possible only to run those functions. To set up and delete those functions, enter into OSD menu. • PWR UP ACTION [ON/OFF] Refer to “Other Functions” section. • AUTO FLIP [ON/OFF] Refer to “Other Functions” section.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ■ ALARM ACTION SETUP Sets the preset to move to when the alarm is input. • ALARM N ACT [NOT USED/PRESET 1~128] Assign counteraction Preset position to each Alarm input ⊙ Preset Setup • PRESET NO. [1~128] If a selected preset is already defined, camera moves to pre-defined position and preset characteristics such as Label and Relay Outputs show on monitor. If a selected preset is not defined, “UNDEFINED” shows on monitor.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ■ EDIT PRESET SCENE ① Using Joystick, move camera to desired position. ② By pressing NEAR key, save current PTZ data. ③ Press FAR key to cancel. ■ EDIT PRESET LABEL ① Edits label to show on monitor when camera arrives at presets. In Edit label menu, a reverse rectangular is cursor. As soon as finishing selecting alphabet, cursor moves to the next digit. ② Using Left/Right/Up/Down of joystick, move to an appropriate character from the Character set.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ Swing Setup • SWING NO. [1~8] Selects Swing number to edit. If a selected Swing has not defined, “NOT USED” is displayed in 1st Position and 2nd Position. • 1ST POS. 2ND POS. [PRESET 1~128] Set up the 2 position for Swing function. If a selected preset is not defined, “UNDEFINED” will be displayed as shown below.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ Pattern setup • PATTERN NO. [1~4] Selects Pattern number to edit. If a selected pattern number is not defined, “UNDEFINED” will be displayed under selected pattern number. • CLR PATTERN [CANCEL/OK] Deletes data in current pattern. • EDIT PATTERN Starts editing pattern. ■ EDIT PATTERN ① By using Joystick, move to start position with appropriate zoom. To start pattern recording, press NEAR key. To exit this menu, press FAR key.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ Group Setup • GROUP NO. [1~8] Selects a group number. If the selected number is not set, “UNDEFINED” will be displayed selected Group number. • CLEAR GROUP [CANCEL/OK] Clears the current setting of a group. • EDIT GROUP Starts editing Group. ■ EDIT GROUP ① Press NEAR key in “NO” list to start Group setup. ② Note that MAX. 20 Functions are allowed in a Group. Move cursor up/down and press NEAR key to set up. ③ Set up Action, Dwell time and Option.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ④ Set up items such as Action, ###, Dwell and OPT ⑤ After finishing setting up a Action, press NEAR key to one-upper-Level Menu(Step②). Move cursor Up/Down to select Action Number and repeat Step ②~ Step ④ to edit selected Group. ⑥ After Finishing setting up all Action, press FAR key to exit. Then cursor should be moved to “SAVE”. Press NEAR key to save data.
XPEED Indoor Series WWW.CNBTEC.COM 4. OSD Menu ⊙ System Initialize • CLEAR ALL DATA Deletes all configuration data such as display, camera, motion setup and so on. • CLR DISPLAY SET Initializes Display Configuration. • CLR CAMERA SET Initializes camera Configuration. • CLR MOTION SET Initializes Motion Configuration. • CLR EDIT DATA Deletes Preset Data, Swing Data, Pattern Data and Group Data. • REBOOT CAMERA Reboots Zoom Camera module. • REBOOT SYSTEM Reboots Speed Dome Camera.
XPEED Indoor Series WWW.CNBTEC.COM 5. Specifications ~ 26x EX-view Models S1465NX / S1465PX Video Signal Camera NTSC PAL Image Pick-up Device 1/4” EX-view HAD CCD Effective Pixels 768(H) x 494(V) 380K 752(H) x 582(V) 440K Horizontal Resolution 470 TV Lines 460 TV Lines S/N Ratio More than 50 dB Zoom 26x Optical Zoom, 12x Digital Zoom Focal Length f=3.5(W) - 91(T) mm Aperture Range F1.6(W) - F3.8(T) Minimum Illumination 1.0Lux (Color) / 0.07Lux (Color, DSS) / 0.
XPEED Indoor Series WWW.CNBTEC.COM 5. Specifications ~ 27x Models SBN-22Z27F /SBN-23Z27F Video Signal NTSC PAL Image Pick-up Device 1/4” IT CCD Effective Pixels 811(H) x 508(V) 410K 795(H) x 596(V) 470K Horizontal Resolution 768(H) x 494(V) 380K 752(H) x 582(V) 440K Resolution 580 TV Lines (BW 600 TV Lines), Sharpness Max. S/N Ratio 50 dB (AGC Off) Zoom 27x Optical Zoom, 10x Digital Zoom Focal Length f=3.6(W) - 97.2(T) mm Aperture Range F1.6(W) - F3.7(T) Minimum Illumination 0.
XPEED Indoor Series WWW.CNBTEC.COM 5. Specifications ⊙ 36x EX-view Models S1965NX/S1965PX Video Signal Camera NTSC PAL Image Pick-up Device 1/4” EX-view HAD CCD Effective Pixels 768(H) x 494(V) 380K Horizontal Resolution 550 TV Lines S/N Ratio 50 dB (Weight ON) Zoom 36x Optical Zoom, 12x Digital Zoom Focal Length f=3.4(W) - 122.4(T) mm Aperture Range F1.6(W) - F4.5(T) ■ Types by installation 752(H) x 582(V) 440K 1.4 Lux 1/60 sec(NT), 1/50 sec(PAL) Minimum Illumination 0.
XPEED Indoor Series WWW.CNBTEC.COM 5. Specifications ~ 36x Models SBB-22Z36F / SBB-23Z36F Video Signal Camera NTSC PAL Image Pick-up Device 1/4” High Sensitivity CCD Horizontal Resolution 768(H) x 494(V) 380K Resolution 540 TV Lines[B/W 600 TV Lines] S/N Ratio 52dB Min[AGC OFF] Zoom 36x Optical Zoom, 12x Digital Zoom Focal Length // Aperture Range f=3.43(W) - 122.4(T) mm //F1.6(W) - F4.5(T) Minimum Illumination Day : 0.1 Lux /Night 0.
XPEED Indoor Series WWW.CNBTEC.COM 5.
XPEED Indoor Series WWW.CNBTEC.COM 5.
XPEED Indoor Series WWW.CNBTEC.
