Ver. 1.
XNET User Manual About this Manual A compatibility and durability test ensures this product’s high performance. This manual is for XNET Network product users only, and it describes operations related to XNET Network products. Please read this manual thoroughly paying attention to cautions and warnings before using the product even if you have used similar products before. Important Notices z The copyright of this manual is owned by CNB Technology Inc.
XNET User Manual Index 1. System Administration .................................................................................................... 4 1.1. Logging On .............................................................................................................................4 1.1.1. Using Internet Explorer ............................................................................................................... 4 1.1.2. ID and Password .................................................
XNET User Manual 1. System Administration 1.1. Logging On You can log on as an administrator using either Internet browser or ‘CMS’ software. (This manual will describe about using Internet browser only.) 1.1.1. Using Internet Explorer Type the IP Address of the XNET product in the address bar and press enter. e.g.) : http://192.168.123.100 If the HTTP port has been changed from the default value, enter the new port as shown below: IP Address of the XNET: Port No. e.g.) : http://192.168.123.100:8080 1.1.
XNET User Manual 1.2. Configuring Camera When you log in as an administrator, XNET’s Basic Setup page will appear as shown in Figure 1-2. Setup pages for different features can be accessed from this page.
XNET User Manual Basic Setup Page can be accessed from Operator group level and up. If you want to access Administrator level page in this user level, you need to log in as Administrator.
XNET User Manual 1.3. Web Viewer (Index.html) When you access an XNET product, Web Viewer page will appear automatically. Viewer area displays the video output from the camera, and menu bar contains taps that lead to each feature setting page.
XNET User Manual DESCRIPTION ITEM Capture Setting - Captures the still image and displays on a pop-up window. [Save to] c:₩xNetCapture - Opens up Basic Setup Page. Setup page for each XNET feature can be opened from this Menu screen. (Please refer to 1.4 for detail) Opens up PTZ page. PTZ - This page can set up digital PTZ of the network camera and control of PTZ movement. (Please refer to 1.8 for detail) Support Model : IGP1030 / INS2000 / IJB2000 Opens up Motion Detection page.
XNET User Manual 1.4. Status Window Status page displays XNET System’s Version and its Ethernet address. Click [▷ Status] button to open the page shown in Figure 1-4. Figure 1-4 Status Page (Internet Explorer 7.
XNET User Manual 1.5. Configuring Users This can give or limit authority to users for controlling Video and other features of XNET system. Click [▷ Users] button to open the page shown in Figure 1-5.
XNET User Manual DESCRIPTION ITEM Displays list of registered users. "root" is the system’s administrator. "root" cannot be added or deleted. Only the password for “root” can be changed. User List This adds a new user. Select “[Add_User]” tap in User List Box. To add a new user, enter User name, Password, and User group then click Add button. Add - Updated User list can be viewed in User List Box. - Up to 10 users can be added.
XNET User Manual 1.6. Setting Date &Time This page will change Date and Time of XNET system. Click [▷ Date & Time] to open the page shown in Figure 1-6. Figure 1-6 Date and Time Page DESCRIPTION ITEM Current Server Time Time Zone Enable Daylight ime New Server Time Time Mode Displays time of XNET system. Selects Time Zone. Enables/ Disables Daylight Saving time. Sets Date and Time of the Server.
XNET User Manual 1.7. Configuring Multi-Viewer Up to 3 cameras connected to XNET’s network can be displayed as sub-cameras simultaneously in Multi-View page. Click [▷ Multi Viewer] to open the page shown in Figure 1-7.
XNET User Manual DESCRIPTION ITEM 1st SubChannel Video Settings 2nd SubChannel Video Settings 3rd SubChannel Video Settings Enable 1st Sub Channel Video Enables viewing of 1st sub Channel Video from the IP address entered. This can only be enabled when IP Address, User Name, and Password is properly entered. 1st IP Address Enter 1st Channel’s IP Address 1st User name Enter 1st Channel’s User name 1st Password Enter 1st Channel’s Password.
XNET User Manual 1.8. Maintaining Server Configurations This page configures system parameters such as system restart, factory default settings, system upgrade, saving configurations, saving images, and other additional features. Click [▷ Maintain Server] to open the page shown in Figure 1-8.
XNET User Manual DESCRIPTION ITEM Maintain Server Restart Restarts the system. It takes about 45 seconds. Restore Resets all parameters except for TCP/IP settings. This restore will be followed by a 45 seconds system reset. Default Resets all parameters to Facory Default setting. This will be followed by a 45 seconds system restart. Reset Log Image/Camera Initialization Deletes all Log Messages. Reset Image Deletes all Alarm Images from the internal Flash Memory.
XNET User Manual 1.9. Generating Log Report Log report contains detailed information about XNET’s image, setup, and error. Click [▷ Log Report] button to open the page shown in Figure 1-9. Figure 1-9 Log Report Page ITEM System Settings Log Report DESCRIPTION System Overview Displays current configurations for XNet option pages. Load List Loads up Log Message file stored in the xNet product. Log Message file can be sorted with date and index.
XNET User Manual 1.10. Configuring Audio Xnet’s Audio features can be configured in this page. Click [▷ Audio] button to open the page shown in Figure 1-10. Figure 1-10 Audio configuration Page DESCRIPTION ITEM Audio Enable Audio Input Enable audio Source Encoding Enables or Disables Audio feature Select audio input source between Microphone and line. Microphone input can be used when users send their voice over XNET system.
XNET User Manual 1.11. Configuring Video XNET’s Video features can be configured in this page. Click [▷ Video] button to open the page shown in Figure 1-11.
XNET User Manual DESCRIPTION ITEM Resolution Main Stream Codec Enable Dual-Codec Frame rate Frame Rate Control MJPEG Appearance RTCP Callback Control Select a resolution of the video image. Selectable resolutions differ by models like the following: IGP1030 : CIF | VGA | XGA | SXGA IDP4000/IVP4000 : CIF | VGA IDP4030/IVP4030 : CIF | VGA | XGA | SXGA INS2000/IJB2000 : CIF | D1 Selects Video Codec.
XNET User Manual 1.12. Configuring RTP/RTSP This is related to XNET’s DDNS server information. Click [▷ RTP/RTSP] to open the page shown in Figure 1-12. Figure 1-12 RTP/RTSP Page DESCRIPTION ITEM RTSP Configuration RTSP Port Multiple-RTSP Port RTP Start Port RTP End Port RTP Configuration Save Reset Maximum number of users to connect - Enter RTSP Port of the Main Stream between 1 and 65535. The default is 554. Enter RTSP Port of the Sub Stream between 1 and 65535. The default is 665.
XNET User Manual 1.13. Configuring Camera Condition This is related to camera features of the XNET products. Click Reset Camera Figure button in System Setup Menu₩Main Server₩ to initialize the Camera during its operation. Click [▷ Camera Condition] button to open the page shown in Figure 1-13.
XNET User Manual ITEM Video Output Format White Balance DESCRIPTION Video Format Selects Video format at Video Out terminal between NTSC and PAL. Enable Video Output Turns the Video Out feature on or off. White Balance Configures Video’s White Balance. White Balance means balancing color temperature by adjusting Red and Blue level.
XNET User Manual 1.14. Configuring the Network(TCP/IP) parameters This configures XNET’s network related parameters. Click [▷ TCP/IP] button to open the page shown in Figure 1-14.
XNET User Manual DESCRIPTION ITEM Enable DHCP Turns DHCP on or off. Check DHCP checkbox to get an IP address automatically from the network using DHCP protocol. Obtained IP address can be viewed by IP Installer. (Note) If the network does not use DHCP server, the product will wait for server’s response for two minutes and restart with its previous IP address. IP address Enter an IP address.
XNET User Manual 1.15. Configuring IP Filtering This configures IP Filters for XNET product. Click [▷ IP Filtering] button to open the page shown in Figure 1-15. Figure 1-15 IP Filtering Page DESCRIPTION ITEM Filter IP Addresses - Displays list of currently established IP Filters. - Adds an IP address to filter out. Enter the IP Address to block and click add button to add it to IP Filtering listbox. The updated list can be viewed in IP Address Listbox. - Up to 20 IP addresses can be added.
XNET User Manual 1.16. Configuring HTTP This configures HTTP port to access XNET’s webpage. Click [▷ HTTP] button to open the page shown in Figure 1-16. Figure 1-16 HTTP Page DESCRIPTION ITEM Enter HTTP Port to access the webpage. Default port is 80, and any other port number has to be entered at the end of the ip address when accessing. (Ex: When using HTTP Port 8080, enter http://192.168.123.100:8080) HTTP HTTP port Save - Applies and saves changes.
XNET User Manual 1.17. Configuring UPnP/DynDNS/Bonjour UPnP is a protocol for IP installer software. You can enable or disable this UPnP, and you can also use a Friendly Name. DynDNS configures XNET’s DDNS server information. Click [▷ UPnP/DynDNS] to open the page shown in Figure 1-17.
XNET User Manual DESCRIPTION ITEM UpnP Setting DynDNS Setting Enable UPnP Friendly Name Enter UPnP’s Friendly Name. Enable DynDNS Enables or disables DynDNS. When enabled, you can automatically obtain a domain from DDNS server by simply registering the XNET product. Enable Anonymous Save Reset Enables or disables DynDNS Anonymous feature. When enabled, DDNS service is used without going through authentication at Autoipset.com DDNS server. Alias Host Name Enter a Host Name for the DynDNS server.
XNET User Manual 1.18. Configuring CMS This configures XNET’s CMS Server information. Click [▷ CMS] to open the page shown in Figure 1-18. Figure 1-18 CMS Page DESCRIPTION ITEM Enter CMS port number for communication with CMS between 1 and 65535. The default is 5000. CMS CMS port Save - Applies and saves changes. Reset - Recalls previously saved configurations.
XNET User Manual 1.19. Configuring Event Type This is related to XNET’s DDNS Server information. Click [▷ Event Types] to view page shown in Figure 1-19.
XNET User Manual DESCRIPTION ITEM Event Enable Enable Event Event Mode Sensor Motion Detection Capture Frame Event Setting Event Schedules Event Output Select Storage Enables or disables event processing. When this is enabled in the SXGA Mode, the transmitted fame rate is reduced by up to 10 fps. When this is enabled in the XGA Mode, the transmitted fame rate is reduced by up to 6 fps. Enables or disables the Alarm sensor.
XNET User Manual 1.20. Configuring Sensor/Alarm This is related to XNET’s DDNS server information. Click [▷ Sensor / Alarm] to open the page shown in Figure 1-20. Figure 1-20 Sensor / Alarm Page DESCRIPTION ITEM Sensor Setting Signal Type Selects the signal type for Alarm Input Port between Normally Close and Normally Open. Alarm Setting Out Interval Configures interval between repeating Alarm Out signals between 1 and 3 seconds. Save - Applies and saves changes.
XNET User Manual 1.21. SMTP Setup This configures mailing out method of Alarm Images once ‘event’ occurred in the XNET system. Click [▷ SMTP] button to open the page shown in Figure 1-21.
XNET User Manual ITEM SMTP Settings DESCRIPTION Enable Internal SMTP Server Turns Internal SMTP Server on or off. When this box is checked, Alarm Image gets mailed out through an internal mail server. Mail Authentication cannot be used in this mode. When this box is unchecked, Alarm Image gets mailed out through an external mail server. Mail Authentication, port, user, password, mail address, etc. needs to be configured.
XNET User Manual 1.22. Configuring FTP This configures how the Alarm Images get sent out using FTP once ‘event’ occurred in the XNET system. Click [▷ FTP] button to open the page shown in Figure 1-22. Figure 1-22 FTP Page ITEM FTP Server DESCRIPTION FTP Name FTP Port Login Information User Name Password Enter the address of the FTP server to send Alarm Images to in the event processing. The client PC at that IP address has to run the FTP server in order to receive the Alarm Images.
XNET User Manual 1.23. Configuring Motion Detection area This defines areas that detect motion, and up to three different areas can be defined in each channel. Click Motion button in Operator mode to open the page shown in Figure 1-23. Figure 1-23 Motion Detection Page DESCRIPTION ITEM Area Displays currently defined Motion Detection area. When an area is selected from the list, its defined area gets displayed and highlighted in viewer window. Up to 3 motion detection area can be defined.
XNET User Manual 1.24. Configuring Multi View Option This configures viewing of up to 4 different camera images simultaneously. Click button in Administrator mode to open the page shown in Figure 1-24. The video from the XNET product gets displayed on top left, and the rest display video signals coming from the IP addresses defined in the Multi-Viewer Setup page.
