User manual

— 1 —

OPERATION CHART:MODULE QW-1325

GENERAL GUIDE

Press C to change from mode to mode in the following sequence.

Note : At this time, press C and release it within one second. Holding down C in any mode for about one or two seconds does not change modes.

Timekeeping Mode

Stopwatch Mode

Alarm Mode

Date Mode

Minute hand

Hour hand

Second hand

24

HOUR.

915

321

60

SEC.

1050

2040

60

M I N.

1545

TIMEKEEPING FUNCTION

To set the date

1. Make sure that your watch is in the Date Mode. If

not, use C to enter the Date Mode.

2. Hold down C while in the Date Mode until the month

digits start to flash on the digital display. The month

digits flash because they are

selected

3. Press C to change the selection in the following

sequence.

Day of week

Date

Month

Normal Date Mode

• Once you reach the normal Date Mode, you have to

hold down C again to display the flashing month.

Day of the week

24-hour dial

Date

4. While the month or date digits are selected (flashing), press B to increase the number.

While the day of the week is selected, pressing B advances to the next day. Holding

down B changes the current selection at high speed.

5. After you set the date, press C while in the day of the week selection to return to the

normal Date Mode (the flashing stops).

• The watch does not make any allowance for leap years. Be sure to manually set

February 29 (when one occurs) for the appropriate date.

• If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the normal Date Mode automatically.

Day of the week abbreviations

Day of the week is displayed as follows.

SU : Sunday MO : Monday

TU : Tuesday WE : Wednesday

TH : Thursday FR : Friday

SA : Saturday

Stopwatch function dials

Example : 33 minutes 42 seconds

Example : 10 minutes 15 seconds

24

HOUR.

915

321

60

SEC.

1050

2040

60

M I N.

1545

24

HOUR.

915

321

60

SEC.

1050

2040

60

M I N.

1545

Minute dial

Second dial

To measure elapsed time

1. In any mode, press B to start the stopwatch.

• The hands of the two upper dials move in accord-

ance with the elapsed minutes and seconds, no mat-

ter what mode you are in.

• Once the measuring time reaches 60 minutes, the

timing starts again from 0 minute 0 second.

• The digital display counts 1/100 seconds in the Stop-

watch Mode only. In other modes, it shows other

data.

2. Press B to stop the stopwatch.

3. Hold down B for about one or two seconds. At this

time, the hands of the upper two dials return to the

12 o’clock position.

• You will not be able to start timing with the stop-

watch until the hands reach this starting position.

24

HOUR.

915

321

60

SEC.

1050

2040

60

M I N.

1545

< Stopwatch Mode >

Second dial

Minute dial

1/100 second

• If the hands of the upper dials do not point exactly to the 12 o’clock position after you

hold down B, pull out the crown of the watch and hold down B again. After you get

the hands pointed to 12 o’clock, press the crown to return it to its original position.

To measure cumulative elapsed time

1. Press B to start the stopwatch.

2. Press B to stop the stopwatch.

3. Press B again to resume timing from the time shown on the display.

You can repeat steps 2 and 3 as many times as you like.

4. Hold down B for about one or two seconds. At this time, the hands of the upper two

dials return to the 12 o’clock position.

ALARM FUNCTION

When the Daily Alarm is switched on, the alarm sounds

for 20 seconds at the preset time each day.

When the Hourly Time Signal is switched on, the watch

beeps every hour on the hour. Note that the Daily

Alarm and the Hourly Time Signal operate based on

the digital time setting.

To set the alarm time

1. Make sure that your watch is in the Alarm Mode. If

not, use C to enter the Alarm Mode.

2. Hold down C while in the Alarm Mode until the hour

digits start to flash on the display. The hour digits

flash because they are

selected

24

HOUR.

915

321

60

SEC.

1050

2040

60

M I N.

1545

Hour

Alarm on

indicator

Hourly Time

Signal on indicator

Minutes

3. Press C to change the selection in the following sequence.

Left minutes digit

Hour

Right minutes digit

Normal Alarm Mode Alarm/Hourly Time Signal setting

• Once you reach the normal Alarm Mode, you have to hold down C again to display

the flashing hour.

4. Press B to increase the selected digits. Holding down B changes the number at high

speed.

• The format (12-hour and 24-hour) of the alarm time matches the format you select for

normal timekeeping.

• When setting the alarm time using the 12-hour format, take care to set the time

correctly as morning or afternoon (indicated as “P”).

To set the digital time

1. Make sure that your watch is in the Timekeeping

Mode. If not, use C to enter the Timekeeping Mode.

2. Hold down C while in the Timekeeping Mode until

the seconds digits start to flash on the display. The

seconds flash because they are

selected

3. Press C to change the selection in the following

sequence.

Hour

Seconds

Minutes

Normal Timekeeping 

Mode

12/24-hour 

format

• Once you reach the normal Timekeeping Mode, you

have to hold down C again to display the flashing

seconds.

24

HOUR.

915

321

60

SEC.

1050

2040

60

M I N.

1545

Seconds

PM indicator

Hour

Minutes

4. While the seconds digits are selected (flashing), press B to reset the seconds to “00”.

If you press B while the seconds count is in the range of 30 to 59, the seconds are

reset to “00” and 1 is added to the minutes. If the seconds count is in the range of 00

to 29, the minutes count is unchanged.

5. While any other digits (besides seconds) are selected (flashing), press B to increase

the number. Holding down B changes the current number at high speed. While the

12/24-hour setting is selected, press B to switch between the two formats.

6. Press C while the 12/24-hour setting is selected and return to the normal Timekeeping

Mode (the flashing stops).

• If you do not operate any button for a few minutes while a selection is flashing, the

flashing stops and the watch goes back to the normal Timekeeping Mode automati-

cally.

To set the analog hands

1. In the Timekeeping Mode, hold down C until the seconds digits start to flash.

2. Stop the second hand by pulling the crown out when the second hand is at 12 o’clock

position.

3. Set the hands by turning the crown.

4. The moment the seconds digits reach “

: 00

”, push the crown in.

STOPWATCH FUNCTION

The Stopwatch function lets you measure elapsed time and cumulative elapsed time.

The range of the stopwatch is 59 minutes, 59.99 seconds.

About stopwatch operation

The stopwatch can be operated while the watch is in any mode. The upper two dials on

the face of the watch indicate the elapsed minutes and seconds during the stopwatch

operation. However, the stopwatch does not operate whenever you are inputting data.

24

HOUR.

915

321

60

SEC.

1050

2040

60

M I N.

1545

C CC

Summary of content (2 pages)

PAGE 1
OPERATION CHART:MODULE QW-1325 GENERAL GUIDE Press C to change from mode to mode in the following sequence. Note : At this time, press C and release it within one second. Holding down C in any mode for about one or two seconds does not change modes. Date Mode Minute hand Hour hand A 60 SEC. 50 40 Alarm Mode B 10 20 30 P 60 M I N. 45 Stopwatch Mode Timekeeping Mode 15 C 30 C C 24 21 HOUR. 3 8 18 C 15 12 Second hand 9 C TIMEKEEPING FUNCTION Stopwatch function dials A 50 60 SEC.
PAGE 2
5. While the Daily Alarm/Hourly Time Signal setting is selected, press B to change the status in the following sequence. Both on Both off Daily Alarm only ABOUT THE BACKLIGHT Pressing A in any mode illuminates the display for about two seconds. If you hold down A, the light automatically disappears after two seconds. • The display is not illuminated while the hands are moving to 12 o’clock position during the stopwatch operation. Hourly Time Signal only A 50 60 SEC. 40 10 20 30 60 M I N. 6.