Use and Care Manual

Break-Through! V70-610 Series
Architectural Coatings PPG Break-Through! Interior/Exterior Water-Borne Acrylic Gloss
PRECAUTIONS
PPG Architectural Finishes, Inc. believes the technical data presented is currently accurate: however, no guarantee of accuracy, comprehensiveness, or performance is given or implied.
Improvements in coatings technology may cause future technical data to vary from what is in this bulletin. For complete, up-to-date technical information, call 1-800-441-9695.
PPG Architectural Finishes, Inc.
One PPG Place
Pittsburgh, PA 15272
www.ppgpaints.com
Technical Services
1-800-441-9695
PPG Architectural Coatings Canada Inc.
1550 rue Ampère, Suite 500
Boucherville (Quebec) J4B 7L4
Architect/Specifier
1-888-PPG-IDEA
WARNING! HARMFUL IF ABSORBED THROUGH SKIN OR IF SWALLOWED. MAY BE HARMFUL IF INHALED. MAY CAUSE RESPIRATO-
RY TRACT, EYE, AND SKIN IRRITATION. Sanding and grinding dusts may be harmful if inhaled. Repeated exposure to high vapor concentrations may cause
irritation of the respiratory system and permanent brain and nervous system damage. Inhalation of vapor/aerosol concentrations above the recommended exposure
limits causes headaches, drowsiness and nausea and may lead to unconsciousness or death. Contains material that can cause target organ damage. Do not
breathe vapor or mist. Do not swallow. Do not get on skin or clothing. Avoid contact with eyes. Avoid prolonged or repeated contact with skin. Wash thoroughly after
handling. Keep container tightly closed and sealed until ready to use. Provide fresh air ventilation during and after application and drying. Avoid the inhalation of
dust, particulates, spray, or mist arising from the application of this preparation. Use personal protective equipment as required. DANGER – RAGS, STEEL WOOL
OR WASTE SOAKED WITH BREAK-THROUGH! INTERIOR/EXTERIOR SATIN WATERBORNE ACRYLIC MAY SPONTANEOUSLY CATCH FIRE IF IMPROPER-
LY DISCARDED. IMMEDIATELY AFTER EACH USE, PLACE RAGS, STEEL WOOL OR WASTE IN A SEALED WATER-FILLED METAL CONTAINER. Note: These
warnings encompass the product series. Prior to use, read and follow product-specific MSDS and label information. FIRST AID: If swallowed, rinse mouth
with water (only if the person is conscious). Call physician immediately. Do not induce vomiting unless directed to do so by medical personnel. If in eyes, rinse with
water for 15 minutes. Check for and remove any contact lenses. In case of contact, immediately flush skin with plenty of water while removing contaminated clothing
and shoes. Get medical attention immediately. If inhaled, remove to fresh air. If experiencing respiratory symptoms, call a POISON CENTER or doctor/physician.
Keep out of the reach of children. For workplace use, an MSDS is available from your retailer or by calling [phone]. EMERGENCY SPILL INFORMATION:
[phone] (U.S.).
V70-610 5/2020
© 2019 PPG Industries, Inc. All Rights Reserved. The PPG Logo and Break-Through! are registered trademarks of PPG Industries Ohio, Inc.
Stir thoroughly before using and occasionally when in use. When using more than one can of the same color, intermix to ensure color uniformity.
USE WITH ADEQUATE VENTILATION. KEEP OUT OF REACH OF CHILDREN. Read all label and Safety Data Sheet (SDS) information prior
to use. SDS are available through our web site or by calling 1-800-441-9695.
Application Equipment: Apply with a high-quality brush, roller, paint pad, or by spray equipment.During application, it is important to maintain
a wet edge due to the quick dry of the product. Rinse brush with warm water periodically during extended brush application. Two coats are rec-
ommended for maximum durability.
Airless Spray: Pressure 1500 to 2000 psi; tip 0.009” to 0.013”. Spray equipment must be handled with due care and in accordance with man-
ufacturer’s recommendation. High-pressure injection of coatings into the skin by airless equipment may cause serious injury.
Brush: Polyester/Nylon Brush
Roller (nap roller cover): 3/16” - 3/8”
Thinning: No thinning required for airless spray application. Reduce 5-10% (up to 12 oz. or 355 mL) with water per U.S. gallon (3.78 L) of paint
for conventional spray, HVLP, and brush applications.
Permissible temperatures during application:
Material: 50 to 90ºF 10 to 32ºC
Ambient: 50 to 90ºF 10 to 32ºC
Substrate: 50 to 90ºF 10 to 32ºC
APPLICATION INFORMATION