FlexiDomeDN IP NWD-495V03-10 | NWD-495V03-20 en Operating Instructions
FlexiDomeDN IP | en 3 Table of Contents 1 Introduction 15 1.1 Type number overview 16 1.2 Unpacking 16 1.3 System requirements 17 1.4 Overview of functions 17 1.4.1 Wide dynamic range 18 1.4.2 Day/Night function 18 1.4.3 Power-over-Ethernet 18 1.4.4 Receiver 18 1.4.5 Video encoding 18 1.4.6 Tri Streaming 19 1.4.7 Recording 19 1.4.8 Multicast 19 1.4.9 Encryption 19 1.4.10 Configuration 19 1.4.11 Tampering recognition and motion detectors 19 1.4.
FlexiDomeDN IP en | 4.3.1 Install menu 27 4.3.2 Defaults 28 4.4 Closing the unit 28 5 Network connection 29 5.1 System requirements 29 5.2 Establishing the connection 29 5.3 Secured network 31 6 Operation via the browser 32 6.1 Livepage 32 6.1.1 Processor load 32 6.1.2 Image selection 33 6.1.3 System log / Event log 33 6.1.4 Saving snapshots 33 6.1.5 Recording video sequences 33 6.1.6 Running recording program 34 6.2 Recordings page 35 6.2.
FlexiDomeDN IP 7.5.1 | en ALC 5 53 7.5.2 Shutter/AGC 54 7.5.3 Day/Night 55 7.5.4 Enhance 56 7.5.5 Color 57 7.5.6 Back Light Compensation (BLC) 58 7.5.7 Installer options 59 7.6 Recording 59 7.6.1 Type 60 7.6.2 Storage information 60 7.7 iSCSI settings 61 7.7.1 iSCSI IP address 61 7.7.2 iSCSI LUN map 62 7.7.3 Target IP address 62 7.7.4 Target node 62 7.7.5 Target LUN 62 7.7.6 Target password 62 7.7.7 Initiator name 63 7.7.8 Initiator extension 63 7.
FlexiDomeDN IP en | 7.12.5 Tamper detection 80 7.13 Alarm e-mail 82 7.13.1 Send alarm e-mail 82 7.13.2 Mail server IP address 82 7.13.3 Layout 83 7.13.4 Destination address 83 7.13.5 Sender name 83 7.13.6 Send e-mail for testing 83 7.14 Service Settings 84 7.14.1 Network 84 7.14.2 Multicasting 87 7.14.3 Encryption 89 7.14.4 Version information 90 7.14.5 Livepage configuration 91 7.14.6 Licenses 93 7.14.7 Maintenance 94 7.
FlexiDomeDN IP | en 7 11 Troubleshooting 101 12 Specifications 103 12.1 Dimensions (mm/inch) 105 12.2 Accessories 105 12.2.1 Power transformers 105 13 Glossary 106 Bosch Security Systems Operating Instructions V 1.0 | 2006.
FlexiDomeDN IP en | Important safety instructions Read, follow, and retain all of the following safety instructions. Heed all warnings on the unit and in the operating instructions before operating the unit. 1. Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist flufffree cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol cleaners. 2.
FlexiDomeDN IP | en 9 230 VAC, 50 Hz, the input and output power cord must comply with the latest versions of IEC Publication 227 or IEC Publication 245. For outdoor use the power cord must comply to NEC400-4 (CEC Rule 4-010) and marked with OUTDOOR, W, or W-A. 8. Power sources - Operate the unit only from the type of power source indicated on the label. Before proceeding, be sure to disconnect the power from the cable to be installed into the unit.
FlexiDomeDN IP 10 en | – unit exhibits a distinct change in performance; – unit does not operate normally when the user correctly follows the operating instructions. 11. Replacement parts - Be sure the service technician uses replacement parts specified by the manufacturer, or that have the same characteristics as the original parts. Unauthorized substitutions may cause fire, electrical shock, or other hazards. 12.
FlexiDomeDN IP | en 11 DANGER! High risk: This symbol indicates an imminently hazardous situation such as "Dangerous Voltage" inside the product. If not avoided, this will result in an electrical shock, serious bodily injury, or death. ! WARNING! Medium risk: Indicates a potentially hazardous situation. If not avoided, this could result in serious bodily injury or death. CAUTION! Medium risk: ! i Indicates a potentially hazardous situation. If not avoided, this may result in minor or moderate injury.
FlexiDomeDN IP 12 en | CAUTION! – Camera Grounding - For mounting the camera in potentially damp environments, ensure to ground the system using the ground connection of the power supply connector (see section: Connecting external power supply). – U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.
FlexiDomeDN IP | en 13 FCC & ICES Information (U.S.A. and Canadian Models Only) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FlexiDomeDN IP 14 en | Disposal Your Bosch product was developed and manufactured with high-quality material and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. Separate collecting systems are usually in place for disused electronic and electrical products.
FlexiDomeDN IP 1 Introduction | en 15 Introduction The FlexiDomeDN IP camera is a small, discreet, high-security surveillance dome containing a high-performance 1/3-inch CCD color camera with integral varifocal lens. The integrated unit is mounted to a wall or ceiling. The sturdy construction and high impact resistant polycarbon dome protect the camera module from damage. The smart camera incorporates 15-bit digital signal processing for outstanding picture performance under all lighting conditions.
FlexiDomeDN IP 16 en | Introduction 1.1 Type number overview Type number NWD-495V03-10P NWD-495V03-20P Lens Varifocal 3 to 9 mm F1.4 Varifocal 3 to 9 mm F1.4 Standard PAL Supply voltage NTSC 24 VAC, 50 Hz or +12 VDC 24 VAC, 60 Hz or +12 VDC (use class 2 power supply) or (use class 2 power supply) or PoE (IEEE 802.3af) PoE (IEEE 802.3af) Table 1.1 FlexiDomeDN IP type numbers 1.2 Unpacking Unpack carefully and handle the equipment with care.
FlexiDomeDN IP 1.3 Introduction | en 17 System requirements – Computer with Windows 2000/XP operating system, network access and Microsoft Internet Explorer web browser version 6.0 or later or – Computer with Windows 2000/XP operating system, network access and reception software, for example VIDOS, BMVS or DIBOS 8.
FlexiDomeDN IP 18 en | Introduction Video images from a single camera can be simultaneously received on several receivers. 1.4.1 Wide dynamic range A unique combination of 15-bit digital video processing that enhances sensitivity and XF-Dynamic which extends the dynamic range, provides a sharper, more detailed image with outstanding accuracy in color reproduction.
FlexiDomeDN IP 1.4.6 Introduction | en 19 Tri Streaming Tri Streaming allows the incoming data stream to be encoded simultaneously according to three different, individually customized profiles. This creates two MPEG4 streams per camera that can serve different purposes, for example, one for local recording and one optimized for transmission over the LAN, and an additional JPEG stream for use with a PDA. 1.4.
FlexiDomeDN IP 20 en | Introduction 1.4.12 Snapshots Individual video frames (snapshots) can be called up as JPEG images, stored on the hard drive or displayed in a separate browser window. 1.4.13 Backup The browser application Livepage has an icon for saving the video images provided by the unit as a file on your computer's hard drive. Clicking this icon stores the video sequences and they can be replayed with the Player from Bosch Security Systems included with the package. 1.4.
FlexiDomeDN IP 2 Disassembly | en 21 Disassembly The camera/housing unit consists of the following parts: Mounting plate Camera module and mounting base Inner liner Trim ring and dome Fig. 2.1 Exploded view CAUTION! ! ! Installation should only be performed by qualified service personnel in accordance with the National Electrical Code or applicable local codes. CAUTION! The camera module is a sensitive device and must be handled carefully. Do not drop when disassembling the unit.
FlexiDomeDN IP 22 en | Mounting the unit 3 Mounting the unit The unit may be surface mounted in two different ways depending on whether the connection is via the top or the side. Refer to the dimensions drawing to find the exact position of the screw holes and the entry hole for the wires. Mounting plate Solid surface (three pre-drilled 8mm holes) Wires Three screws (supplied Conduit with camera) Suspension wire Integrated camera unit and base Three screws (M5, supplied) Fig. 3.
FlexiDomeDN IP 3.1 Mounting the unit | en 23 Attach the mounting plate 1. Use the mounting plate as a drilling temple to drill three holes in the mounting surface. 2. Use the supplied plugs and screws to attach the mounting plate to the surface. 3. With a rear connection, leave the cap in place. With a side connection: a. remove the cap covering the side entrance; b. attach a 22 mm / ½ inch (PG16) gland conduit to the mounting plate. 3.
FlexiDomeDN IP 24 en | Mounting the unit 3.2.1 Power connection 1. 2. Use a class 2 power supply 24 VAC or +12 VDC. Use AWG16 to 22 stranded wire or AWG16 to 26 solid wire; cut back 10 mm (0.4 inch) of insulation. 3. Run the power wires through the closed rubber grommet of the connection box cover. 4. Attach the power wires to the supplied plug (polarity is not important) as follows: Pin 1 5.
FlexiDomeDN IP Camera set-up | en 25 4 Camera set-up 4.1 Camera positioning You can connect a monitor to the miniature 2.5mm jack socket on the printed circuit board to help set up the camera. This socket provides a composite video signal (with sync). An optional cable (code number S1460) is available for making this connection. Focus Focal length Navigation switches Thumbwheels Monitor jack Fig. 4.
FlexiDomeDN IP 26 en | Camera set-up – To obtain a horizontal horizon (for tilted ceilings or sidewall mounting), rotate the base of the lens as necessary to align the picture shown on the monitor. Do not rotate more than 340°. CAUTION! The CCD image sensors are highly sensitive and ! require special care for proper performance and extended lifetime. Do not expose them to direct sunlight or bright spotlights in operating and non-operating conditions.
FlexiDomeDN IP – Camera set-up | en 27 Press the menu/select (center) key to access the menus or to move to the – Up key Menu/select key next or previous menu. Right key Press the menu/select Down key key for approximately 1.5 seconds to open the Left key Installer menu. – Use the up or down keys to scroll through a menu. – Use the left or right keys to move through options or to set parameters.
FlexiDomeDN IP 28 en | Camera set-up i 4.3.2 NOTICE! The new IP address, subnet mask and gateway address are set after you leave the menu. The camera reboots internally and the new values are set after a few seconds. Defaults To restore all parameters (including IP address) to the factory defaults, press and hold the Up navigation key for at least 10 seconds and then confirm. Allow a few seconds for the camera to optimize the picture after a mode reset. i 4.
FlexiDomeDN IP 5 Network connection | en 29 Network connection A computer with Microsoft Internet Explorer can be used to receive live images from the camera, control cameras and replay sequences stored on the local hard drive. The camera is configured over the network using the browser or via the Configuration Manager (supplied with the product). The configuration options using the menu system of the camera itself are limited to setting up the lens and network. i 5.
FlexiDomeDN IP 30 en | Network connection Password protection in camera If the camera is password-protected, a message to enter the password appears. i NOTICE! A camera offers you the option of limiting access across various authorization levels. 1. Enter the user name and the associated password in the appropriate fields. 2. Click OK. If the password is correct, the desired page is displayed. After a short time when the connection is established, the Livepage with the video image appears.
FlexiDomeDN IP 5.3 Network connection | en 31 Secured network If a Radius server is used for network access control (802.1x authentication), the camera must be configured first. To configure the camera for a Radius network, connect it directly to a PC via a crossed network cable and configure the two parameters, identity and password. Only after these have been configured can you communicate with the camera via the network. Bosch Security Systems Operating Instructions V 1.0 | 2006.
FlexiDomeDN IP 32 en | Operation via the browser 6 Operation via the browser 6.1 Livepage After the connection is established, the Livepage is initially displayed. It shows the live video image on the right of the browser window. Depending on the configuration, various text overlays may be visible on the live video image. Other information may also be shown next to the live video image on the Livepage. The display depends on the settings on the Livepage configuration page. 6.1.
FlexiDomeDN IP 6.1.2 Operation via the browser | en 33 Image selection You can view the image on a full screen. – Click one of the MPEG-4 Stream 1, MPEG-4 Stream 2 or MJPEG tabs below the video image to switch between the different displays for the camera image. 6.1.3 System log / Event log The System log field contains information about the operating status of the camera and the connection. These messages can be saved automatically in a file.
FlexiDomeDN IP 34 en | Operation via the browser – Saving begins immediately. The red dot on the icon flashes to indicate that a recording is in progress. 2. Click the symbol for recording video sequences again. Saving is terminated. Installing Player You can play back saved video sequences using the Player from Bosch Security Systems, which can be found on the software CD supplied.
FlexiDomeDN IP 6.2 Operation via the browser | en 35 Recordings page You can access the Recordings page for playing back recorded video sequences from the Livepage as well as from the Settings menu. The Recordings link is only visible if a storage medium has been selected (see “Recording” on page 59). – Click Recordings in the navigation bar in the upper section of the window. The playback page appears. . 6.2.
FlexiDomeDN IP 36 en | Operation via the browser 6.2.2 Controlling playback You will see a time bar below the video image for quick orientation. If a particular sequence has been selected for playback by means of click, the selected sequence is highlighted. The associated time interval is displayed in the bar in blue. A green arrow above the bar indicates the position of the image currently being played back within the sequence.
FlexiDomeDN IP Operation via the browser | en 37 Jump to start of active video sequence or to previous sequence in the list Jump to end of active video sequence or to next sequence in the list You can use the slide control to control playback speed and fast forward/rewind: positioning in the middle indicates playback at recording speed, left indicates rewind, and right fast forward. The fast forward or rewind speed changes, depending on how far you move the slide control toward the runner icons.
en | Operation via the browser i FlexiDomeDN IP NOTICE! Bookmarks are only valid while you are in the Recordings page; they are not saved with the sequences. As soon as you leave the page all bookmarks are deleted. V 1.0 | 2006.
FlexiDomeDN IP Configuration via the browser | en 39 7 Configuration via the browser 7.1 Settings When a connection is established, the Livepage is initially displayed. Click Settings in the application title bar to configure the camera and the application interface. A new page containing the configuration menu is opened. All settings are stored in the camera memory, and they are preserved even if the power is interrupted.
FlexiDomeDN IP 40 en | Configuration via the browser You can view the current settings by opening one of the configuration pages. 1. Click one of the menu options on the left of the window. The associated sub-menu is opened. 2. Click one of the links in the sub-menu. The corresponding page is opened. The settings are changed by entering new values or by selecting a pre-defined value in a list field.
FlexiDomeDN IP Configuration via the browser | en 41 Click the Settings link at the top of the window to close the window without saving the changes made. 7.2 General Settings Various basic data for the camera can be set or selected here. 7.2.1 Camera identification Camera name The camera can be assigned a name to assist in identifying it. The name simplifies the management of multiple devices in more extensive systems, for example using the VIDOS or BVMS software.
en | Configuration via the browser 7.2.2 FlexiDomeDN IP Password protection A camera is generally protected by a password to prevent unauthorized access to the unit. You can use various authorization levels (User name:) to limit access. NOTICE! Proper password protection is only guaranteed if all i higher authorization levels are also protected with a password. For example, if a live password is assigned, a service and a user password should also be set.
FlexiDomeDN IP i 7.2.3 Configuration via the browser | en 43 NOTICE! The new password is then saved by clicking the Set button. You should therefore click the Set button immediately after entering and confirming the password, even if you also want to assign a password to another user name. Language selection Website language Select the language for the user interface here. 7.2.4 Date and time Date format Choose the desired date format here (Europe: DD.MM.YYYY; USA: MM.DD.YYYY; Japan: YYYY/MM/ DD).
en | Configuration via the browser 7.2.5 FlexiDomeDN IP Time server The camera supports several network time server protocols and can synchronize its internal clocks with various types of time servers. The device calls up the time signal automatically once every minute. Unit time zone Select the time zone in which the system is located. Daylight saving time The internal clock can automatically switch between normal and daylight saving time (DST).
FlexiDomeDN IP 9. Configuration via the browser | en 45 When you are finished, click OK to save and activate the table. Time server IP address Enter the IP address of a time server. Time server type Choose the protocol used by the selected time server. It is recommended that you choose the SNTP server protocol. This protocol provides higher accuracy and is required for certain applications, as well as for future additions. Choose Time server, if the server uses RFC 868 as protocol. 7.
FlexiDomeDN IP 46 en | Configuration via the browser Alarm mode stamping Choose On if a text message should be overlaid in the event of an alarm. It can be displayed at a position of your choice using the Custom option. Or it can be set to Off if no overlay of this information is to be shown. 1. Select the desired position from the lists. – If you have selected the Custom option, additional fields are displayed to specify the exact position (Position (XY):). 2.
FlexiDomeDN IP Configuration via the browser | en 47 structures). To do this, the camera simultaneously generates two data streams (Dual Streaming), for which you can select different compression settings, for example one setting for transmissions to the Internet and one for LAN connections. Pre-programmed profiles are available, which each give priority to different perspectives.
FlexiDomeDN IP 48 en | Configuration via the browser ally updated above the previews. i 1. Click a tab to select the associated stream. 2. Select the desired setting from the list. NOTICE! Stream 2 is always transmitted for alarm connections and automatic connections. Take this into account when assigning the profile. Preview for Select which video data stream should be displayed in the previews.
FlexiDomeDN IP i Configuration via the browser | en 49 NOTICE! The parameters as a group constitute a profile and are dependent on one another. If you enter a setting outside the allowed range for a parameter, the nearest valid value is substituted when the settings are saved. Profile name You can enter a new name for the profile here. The name is then displayed in the list of available profiles in the Active encoder profile: field.
en | Configuration via the browser FlexiDomeDN IP Default Click Default to return the profile to the factory default values. Details Click Details to display further settings for image quality and communication parameters. These settings require familiarity with MPEG and video encoding standards. Incorrect settings could result in useless video images. Max. data rate This maximum data rate is not exceeded under any circumstances.
FlexiDomeDN IP Configuration via the browser | en 51 rate. A value of 31 results in a very high refresh rate and lower image quality. I-frame distance This parameter determines the number of inter-coded frames between two I-frames. 7.4.3 JPEG posting You can save individual JPEG images on an FTP server at certain intervals. You can then retrieve these images at a later date to reconstruct alarm events if required.
en | Configuration via the browser FlexiDomeDN IP was stored on February 16, 2006 at 12.45 p.m. and 30 seconds. JPEG posting interval Enter the interval in seconds at which the images will be sent to an FTP server. Enter zero if you do not want any images to be sent. FTP server IP address Enter the IP address of the FTP server on which you wish to save the JPEG images. FTP server login Enter your login name for the FTP server.
FlexiDomeDN IP 7.5 Configuration via the browser | en 53 Camera settings i 7.5.1 NOTICE! If the camera is in monochrome mode, all color related menu items are disabled and cannot be accessed. ALC Video level Adjust the video output level (-15 to 0 to +15). Peak Average Adjust the balance between peak and average video control (-15 to 0 to +15). At -15 the camera controls the average video level, at +15 the camera controls the peak video level.
FlexiDomeDN IP 54 en | Configuration via the browser 7.5.2 Shutter/AGC Shutter – AES (auto-shutter) - the camera automatically sets the optimum shutter speed for manual iris lenses. The camera tries to maintain the selected shutter speed (1/60 [1/50], 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/5000, 1/ 10K) as long as the light level of the scene permits. – FL - flickerless mode avoids interference from light sources (recommended for use with video iris or DC iris lenses only).
FlexiDomeDN IP Configuration via the browser | en 55 the maximum value the gain can have during AGC operation (0, 1, ... 26). In FIXED mode the gain is set at a predefined not scene dependent value. Select the gain setting (0, 1, ... 26). 7.5.3 Day/Night The Flexidome IP Day/Night camera is equipped with a motorized IR filter. The IR filter can be removed in low-light or IR illuminated applications.
en | Configuration via the browser – FlexiDomeDN IP Enhanced: the camera optimizes contrast in applications with high IR illumination levels. – Normal: the camera optimizes contrast in mono applications with visible light illumination. 7.5.4 Enhance Auto Black Autoblack ON automatically increases the visibility of details. Black Level Adjusts the black level between 0 and approximately 110mV. Zero position of slider corresponds to the factory default black level.
FlexiDomeDN IP 7.5.5 Configuration via the browser | en 57 Color White Balance – ATW: Auto tracking white balance allows the camera to constantly adjust for optimal color reproduction. – AWB HOLD: Puts the ATW on hold and saves the color settings. – In MANUAL mode the Red, Green and Blue gain can be manually set to a desired position. WB Speed Adjust the speed of the white balance control loop. Red Gain ATW mode and AWB hold mode: adjusts the Red gain to optimize the white point.
en | Configuration via the browser 7.5.6 FlexiDomeDN IP Back Light Compensation (BLC) When ON, the video level is optimized for the selected area of the image. Parts outside this area may be underexposed or overexposed (this is normal). To set-up an area for BLC, click Area Selection. Selecting an area When you click Area Selection a pop-up window appears with a still picture of the received video. Use your mouse to select an area in the picture.
FlexiDomeDN IP 7.5.7 Configuration via the browser | en 59 Installer options Select the synchronization method for the camera: Internal for free running camera operation; Line Lock to lock to the power supply frequency. You can disable the buttons on the camera to prevent unauthorized change of the camera settings. – Click Restore all defaults to restore the factory defaults. – A confirmation screen appears. Allow 5 seconds for the camera to optimize the picture after a mode reset. 7.
FlexiDomeDN IP 60 en | Configuration via the browser 7.6.1 Type Select the desired storage medium to subsequently configure the recording parameters. i NOTICE! If you select VRM, the Video Recording Manager manages all recording and you are not able to make any further configurations via the web browser. CAUTION! ! 7.6.2 If you switch the storage medium from iSCSI server to RAM recording, the settings on the page iSCSI settings are lost and can only be restored by reconfiguring them.
FlexiDomeDN IP 7.7 Configuration via the browser | en 61 iSCSI settings If you select type iSCSI server as the storage medium, you then need to set up a connection to the desired iSCSI storage device and set the configuration parameters. i 7.7.1 NOTICE! The storage device selected must adhere to the iSCSI specification, be available on the network and be completely set up. Amongst other things, it must have an IP address and be divided into logical drives (LUN). iSCSI IP address 1. 2.
FlexiDomeDN IP 62 en | Configuration via the browser 7.7.2 iSCSI LUN map The LUN map displays the logical drives configured for the iSCSI storage device. The current user is displayed for each drive. 1. Double-click a free drive (LUN). The associated information is called up and automatically displayed in the fields below the map. 2. If the logical drive is password protected, you must first enter the password in the Target password field and click the Set button.
FlexiDomeDN IP 7.7.7 Configuration via the browser | en 63 Initiator name The initiator name is automatically displayed after a connection has been established. 7.7.8 Initiator extension Enter the initiator extension. For the sake of clarity, you can enter a name or the existing extension with a comment, for example "– Camera 2". 7.7.9 Decoupling the drive used Each drive can only be associated with one user.
en | Configuration via the browser 7.8 FlexiDomeDN IP Partitioning A partition can be set up for recordings of the camera in a similar manner to the partitioning often found on computer hard drives. Parameters such as size, quality and type of video recording or compression standard used can be specified for the partition. Modifying these parameters leads to reorganization, during which stored data is lost.
FlexiDomeDN IP Configuration via the browser | en 65 . 2. Read the information text in the upper section of the window. 3. Click in the text fields to enter values or use the other controls that are available, such as buttons, checkboxes or list fields. 4. Click Next>> in the lower section of the window to continue with the next step. 5. Click <
en | Configuration via the browser 2. FlexiDomeDN IP Click Finish to complete the configuration. All settings are now transferred to the unit and subsequently become effective. 7.8.2 Partition status 1. Click Partition status. – A window opens showing information on the highlighted partition. This window provides information about the current configuration of the partition. No changes can be made here. 2. 7.8.3 Click OK to close the window.
FlexiDomeDN IP 1. Configuration via the browser | en 67 Click Edit partition. – A new window with the entries for the selected partition is opened. You can modify the configuration in the Partition properties window. 2. Enter the necessary changes. 3. Click Set to save the modifications. 4. After closing the window, click Set in the main window to transfer the changes to the unit and to save them. Type of recording Select the required recording type.
FlexiDomeDN IP 68 en | Configuration via the browser The unit uses a special recording mode during alarm recording for optimal usage of storage capacity. As soon as a time gap for alarm recording begins, a recording is continuously made on one segment, which is the size of a complete alarm sequence (pre- and post-alarm time). This segment in the partition functions in a similar manner to a ring buffer and is overwritten until an alarm is actually triggered.
FlexiDomeDN IP 7.8.4 Configuration via the browser | en 69 Deleting partitions You can delete a partition at any time. CAUTION! Deleting a partition leads to the entire hard drive ! being reorganized and loss of all sequences stored on the drive. Consequently, you should check the recordings before deleting any partition and back up important sequences on the computer's hard drive. 1. Click Delete partition button to delete the highlighted partition.
en | Configuration via the browser FlexiDomeDN IP 1. Click one of the tabs to edit the corresponding profile. 2. Click Default to return all settings to their defaults. 3. Click Copy settings if you want to copy the currently visible settings to another profile. A dialog appears and you can select the target profile for the copied settings. 4. Click Set in each profile tab that you want saved. Standard profile Select the encoder profile to use for continual recording.
FlexiDomeDN IP Configuration via the browser | en 71 Alarm track recording This parameter is only active, if the alarm tracks have been configured. – Click the checkbox to activate alarm track recording. The pre-alarm time gap is displayed automatically. Post-alarm time Select the post-alarm time gap from the list box. Post-alarm profile Select the encoder profile to use for recording during the postalarm time. The Standard profile option sets this to the same as the standard profile.
FlexiDomeDN IP 72 en | Configuration via the browser 7.10 Recording scheduler Set all parameters for recording. Recording can be performed continuously or when an alarm occurs. . In the recording scheduler you can assign weekdays and times to the recording profiles you have created that define when alarms trigger recording. You can assign as many time periods (in 15-minute intervals) for any day of the week. When you move the mouse cursor over the table, the time is displayed.
FlexiDomeDN IP 5. 6. Configuration via the browser | en 73 Click Clear all to deselect all of the intervals. When you are finished, click Set to save the settings in the device. Holidays You can define holidays, which will override the settings for the normal weekly schedule. This allows you to apply the settings for Sundays to other days of the week. 1. Click the Holidays tab. Days that have already been defined are shown in the table. 2. Click Add. This opens a new window. 3.
en | Configuration via the browser 2. FlexiDomeDN IP Click Stop to deactivate the recording schedule. Recordings that are currently running are interrupted and the configuration can be modified. 7.10.2 Recording status The graphic indicates the recording activity in this partition. You will see an animated graphic while recording is taking place. 7.11 Alarm Settings 7.11.1 Alarm connections You can select the response of the camera when an alarm occurs.
FlexiDomeDN IP Configuration via the browser | en 75 Number of destination IP address Here you assign the numbering for the IP addresses to be contacted in the event of an alarm. The unit contacts the remote locations one after the other in the numbered sequence until a connection has been established. Destination IP address For each number, enter the corresponding IP address for the desired remote location. Destination password If the remote location is password protected, enter the password here.
en | Configuration via the browser FlexiDomeDN IP connection. The appropriate certificates must also have been uploaded (see “SSL certificate upload” on page 96). You can configure and activate encryption for media data (video, audio, metadata) on the Encryption page (see “Encryption” on page 89). Auto-connect Select On if an active connection should be re-established automatically to one of the previously specified IP addresses after each restart, connection breakdown or network failure.
FlexiDomeDN IP 7.12 Configuration via the browser | en 77 VCA The camera contains an integrated Video Content Analysis (VCA), which can detect and analyze changes in the signal. Such changes can be due to movements in the camera's field of view. You can configure the video content analysis for the camera. If necessary, click Default to return all settings to their default values. 7.12.1 Analysis Select the option On to activate the video content analysis.
FlexiDomeDN IP 78 en | Configuration via the browser i 7.12.2 NOTICE! On the Livepage configuration page, you can enable additional information overlays for the live video image too (see “Livepage configuration” on page 91). Analysis type Select the required analysis algorithm. By default, only Motion+ is available – this offers a motion detector and essential recognition of tampering. The current alarm status is displayed for information purposes. i 7.12.
FlexiDomeDN IP 7.12.4 Configuration via the browser | en 79 Sensitivity Sensitivity is available for the Motion+ analysis type. The basic sensitivity of the motion detector can be adjusted for the environmental conditions to which the camera is subject. The sensor reacts to variations in the brightness of the video image. The darker the observation area, the higher the value that must be selected. Min.
FlexiDomeDN IP 80 en | Configuration via the browser 4. If necessary, click Select all to select the entire video frame for monitoring. 5. Right-click any fields you wish to deactivate. 6. Click OK to save the configuration. 7. Click the close button (X) in the window title bar to close the window without saving the changes. 7.12.5 Tamper detection You can detect the tampering of cameras and video cables by means of various options.
FlexiDomeDN IP Configuration via the browser | en 81 the scene provides a basis for recognition. Scene too dark Activate this function if tampering associated with covering the objective (for instance, by spraying paint on it) should trigger an alarm. The average brightness of the scene provides a basis for recognition.
FlexiDomeDN IP 82 en | Configuration via the browser 1. Click Select area to configure the sensor fields. A new window will open. 2. If necessary, click Clear all first to clear the current selection (fields marked red). 3. Left-click the fields to be activated. Activated fields are marked red. 4. If necessary, click Select all to select the entire video frame for monitoring. 5. Right-click any fields you wish to deactivate. 6. Click OK to save the configuration. 7.
FlexiDomeDN IP Configuration via the browser | en 83 sent to the mail server via the address you entered. Otherwise leave the box blank (0.0.0.0). 7.13.3 Layout You can select the data format of the alarm message. – Standard (with JPEG): e-mail with JPEG image file attachment. – SMS: e-mail in SMS format to an e-mail-to-SMS gateway (for example to send an alarm by cellphone) without an image attachment.
FlexiDomeDN IP 84 en | Configuration via the browser 7.14 Service Settings 7.14.1 Network The settings on this page are used to integrate the unit into an existing network. NOTICE! i Changes to the IP address, subnet mask or gateway address are transferred to the unit by clicking Set. However, they do not become active until the device is restarted. – Click Set after entering a new IP address. – To do this, enter the old IP address followed by / reset (for instance 192.168.0.
FlexiDomeDN IP Configuration via the browser | en 85 restarted it can only be accessed at the new IP address. IP address Enter the desired IP address for the camera in this field. The IP address must be valid for the network. Subnet mask Enter the appropriate subnet mask for the set IP address here. Gateway address If you want the unit to establish a connection to a remote location in a different subnet, enter the IP address of the gateway here. Otherwise, this field can remain empty (0.0.0.0).
FlexiDomeDN IP 86 en | Configuration via the browser If you want to limit connections to SSL encryption, you must set the Off option in the HTTP browser port, the RCP+ port, and Telnet support. This deactivates all unencrypted connections allowing connections on the HTTPS port only. i NOTICE! You can configure and activate encryption for media data (video, audio, metadata) on the Encryption page (see “Encryption” on page 89).
FlexiDomeDN IP Configuration via the browser | en 87 nents and can send SNMP messages (traps) to IP addresses. It supports SNMP MIB II in the unified code. If you wish to send SNMP traps, enter the IP addresses of one or two required target devices here. To choose which traps are sent: 1. Click Select. A dialog box appears. 2. Click the check boxes of the appropriate traps. 3. Click OK to close the window and send all of the checked traps.
FlexiDomeDN IP 88 en | Configuration via the browser to receive the video signal from an encoder simultaneously. This is either done by duplicating the data stream in the unit and then distributing it to multiple receivers (multi-unicast) or by distributing an individual data stream in the network itself to multiple receivers in a defined group (multicast). You can enter a dedicated multicast address and port for each stream. You can switch between the streams by clicking the associated tabs.
FlexiDomeDN IP Configuration via the browser | en 89 Port If there are simultaneous data streams at the same multicast address, you must assign different ports to each data stream. Enter the port address for the relevant stream here. Streaming Click in the checkbox to activate multicast streaming mode for the relevant stream. An activated stream is marked with a check. Multicast packet TTL A value can be entered to specify how long the multicast data packets are active on the network.
en | Configuration via the browser FlexiDomeDN IP 5. Click Generate keys to generate new keys for marked 6. Click Edit to enter a key for a marked entry manually. streams. Automatic key exchange: Mark this checkbox to activate an automatic key exchange between two devices (or the camera and a software decoder) across an encrypted connection. 7.14.4 Version information This window is for information only and cannot be modified. Keep this information at hand when seeking technical support.
FlexiDomeDN IP 7.14.5 Configuration via the browser | en 91 Livepage configuration In this window, you can adapt the appearance of the Livepage to meet your requirements. Options are provided here to display various information and operating elements in addition to the video image. Moreover, individual background graphics can be used for the main window and the upper area of the window (banners). NOTICE! Either GIF or JPEG images can be used.
FlexiDomeDN IP 92 en | Configuration via the browser Logo URL Enter the path to a suitable background graphic in this field. The image can be stored on a local computer, a local network or at an Internet address. – Click Search if necessary to find a suitable image on the local network. Device logo URL Enter the path for a suitable image for the upper part of the window (banner) here. The image can be stored on a local computer, a local network or at an Internet address.
FlexiDomeDN IP Configuration via the browser | en 93 Show system log The system messages are displayed with the date and time in a field next to the video image and provide information about the establishment and termination of connections etc. Save event log Select this option to save event messages in a text file on the local computer. This file can be viewed, edited and printed with any text editor or the standard Office software.
FlexiDomeDN IP 94 en | Configuration via the browser i 7.14.7 NOTICE! The activation key cannot be deactivated again and is not transferable to other units. Maintenance CAUTION! Before starting the firmware update, make sure that ! you have selected the correct upload file! Uploading the wrong files can result in the unit no longer being addressable, requiring it to be replaced.
FlexiDomeDN IP Configuration via the browser | en 95 NOTICE! A firmware update resets all camera parameters to i their factory default values. If you wish to retain the old values first save the configuration by performing a configuration download. After the firmware update you can reload your parameter values by performing a configuration upload. To update the firmware: 1. First, save the update file to the hard disk. 2. Enter the full path for the update file in the field or click Browse...
FlexiDomeDN IP 96 en | Configuration via the browser Configuration upload 1. Enter the full path of the file to upload or click Browse... to select the desired file. 2. Make certain that the file to be loaded comes from the 3. Click Upload to begin transmission to the unit. The same device type as the unit you want to reconfigure. progress bar allows you to monitor the transfer. Once the upload is complete, the new configuration is activated.
FlexiDomeDN IP 8 Connections between video servers | en 97 Connections between video servers A camera can be used as a transmitter and a compatible MPEG4 hardware decoder with a connected monitor as a receiver using an Ethernet network connection. This way it is possible to cover large distances with little effort for installation or cabling. 8.0.1 Installation Cameras are designed to connect with other VIP devices automatically with the corresponding configuration.
en | Connections between video servers 8.0.4 FlexiDomeDN IP Connecting with a Web browser Various requirements must be met in order to operate using a Web program. i NOTICE! Transmitter and receiver must be located in the same subnet to establish a hardware connection with a Web browser. 1. Use the Web browser to connect to the receiver. Its home page is displayed. Under Video sources on the page Connections, select the camera.
FlexiDomeDN IP 9 Operation with decoder software | en 99 Operation with decoder software VIDOS The camera video server and VIDOS software combine to provide a high-performance system solution. VIDOS is software for operating, controlling and administering CCTV installations (such as surveillance systems) at remote locations. It runs under Microsoft Windows operating systems. Its main job is decoding video, audio and control data from a remote transmitter.
FlexiDomeDN IP 100 en | Maintenance 10 Maintenance 10.1 Testing the network connection The ping command can be used to check the connection between two IP addresses. This allows you to test whether a device is active in the network. 1. Open the DOS command prompt. 2. Type ping followed by the IP address of the device. If the device is found, the response appears as " Reply from ... ", followed by the number of bytes sent and the transmission time in milliseconds.
FlexiDomeDN IP 11 Troubleshooting | en 101 Troubleshooting If you cannot resolve a fault, please contact your supplier or system integrator or go direct to Bosch Security Systems Customer Service. The version numbers of the internal processors can be viewed on a special page. Please note this information before contacting Customer Service. 1. In the address bar of your browser, after the unit IP address enter /version (for example 192.168.0.80/version). 2.
FlexiDomeDN IP 102 en | Troubleshooting Malfunction Possible causes Solution The unit does not Alarm source is not Select possible alarm sources on report an alarm. selected. the Alarm sources configuration page. No alarm response specified. Specify the desired alarm response on the Alarm connec- tions configuration page, if necessary change the IP address. The unit is not opera- Power failure during protional after firmware Have the unit checked by Cus- gramming by the update file.
FlexiDomeDN IP 12 Specifications | en 103 Specifications Type number NWD-495V03-10 NWD-495V03-20 Standard PAL NTSC Active pixels 752 x 582 768 x 494 Lens focal length 2.6 to 6 mm 2.6 to 6 mm F-stop F1.4 F1.4 All versions Rated supply voltage 24 VAC or +12 VDC or Power-over-Ethernet (IEEE 802.3af) 12 to 28 VAC, 45 to 60 Hz (850 mA) +11 to +36 VDC (750 mA) Sensitivity color < 0.32 lux (0.031 fc) NightMode < 0.11 lux (0.
FlexiDomeDN IP 104 en | Specifications All versions Image resolutions 704 × 576/480 pixels (D1/4CIF) (PAL/NTSC) 464 × 576/480 pixels (2/3 D1) 704 × 288/240 pixels (2CIF) 352 × 576/480 pixels (1/2 D1) 352 × 288/240 pixels (CIF) 176 × 144/120 pixels (QCIF) Total delay 120 ms (PAL/NTSC, MPEG-4, no network delay) Image refresh rate 1 ... 50/60 fields/s adjustable (PAL/NTSC) field/image-based coding Network protocols TCP, UDP, IP, HTTP(S), IGMP v2/v3, ICMP, ARP, RTP, Telnet, DHCP, SNMP V2, 802.1x V 1.
FlexiDomeDN IP 12.1 Specifications | en 105 Dimensions (mm/inch) 40.37 1.59 47.6 1.87 22.35 0.88 25.22 0.99 42.03 1.65 121 4.76 158 6.2 12.2 0.9 5.6 142.5 23.5 22.5 0.9 Accessories Contact your Bosch representative for the latest available accessories. Bosch Security Systems Operating Instructions V 1.0 | 2006.
FlexiDomeDN IP 106 en | Glossary 13 Glossary Brief explanations of some of the terms and abbreviations found in this user guide are given below. 10/100 Base-T IEEE 802.3 specification for 10 or 100 MBit/s Ethernet 802.1x The IEEE standard, 802.1x, provides a general method of access control and authorization for IEEE 802-based networks.
FlexiDomeDN IP Glossary | en 107 IP See Internet Protocol IP address A 4-byte number uniquely defining each device on the Internet. It is usually written in dotted decimal notation with full stops separating the bytes, for example "209.130.2.193".
FlexiDomeDN IP 108 en | Glossary RS232/RS422/RS485 Standards for serial data transmission RTP Realtime Transport Protocol; A transmission protocol for SNTP Simple Network Time Protocol is a simplified version of NTP real-time video and audio (see NTP). SSL Secure Sockets Layer is an encryption protocol for data transmission in IP-based networks.
Bosch Security Systems Robert-Koch-Straße 100 D-85521 Ottobrunn Germany www.boschsecuritysystems.
