Owner’s Manual Using the Ducted Gas Central Heating Dual Cycle Refrigerated Air Conditioning Ducted Evaporative Air Conditioning with your multi-appliance Navigator Control Radio Frequency & Low Voltage Please keep this important manual in a safe place. It is the owner’s responsibility to ensure that regular maintenance is carried out on units. Failure to do so will void all guarantees beyond statutory and legal requirements. www.climatetechnologies.com.
Multi-Appliance Navigator Control Contents INTRODUCTION.............................................................................................................................. 4 1. YOUR MULTI-APPLIANCES ......................................................................................................................................... 4 2. GENERAL INFORMATION............................................................................................................................................
Multi-Appliance Navigator Control Contents SAFETY & OWNER RESPONSIBILITY.................................................................................................25 PRECAUTIONS .....................................................................................................................................25 FEATURES............................................................................................................................................25 POWER INTERRUPTION......................
Multi-Appliance Navigator Control Navigating the Controls INTRODUCTION 1. YOUR MULTI-APPLIANCES You have chosen one of the world's most advanced Navigator Control systems. The Navigator Controller is intended for use in controlling BONAIRE Gas Heaters, Evaporative Coolers or Dual Cycle Refrigerated Coolers. At any one time, the Navigator Controller can control multiple units. The Navigator Controller also allows simultaneous control of a combined Gas Heater / Refrigerative Cooler units (Dual Cycle).
Multi-Appliance Navigator Control Navigating the Controls Your Navigator Controller is available in two versions 1. Wall Mounted Control (Wired) 2. Remote Control (Wireless) These operating notes cover both versions. Whether hand held or wall mounted take advantage of the versatility your Navigator Controller offers.
Multi-Appliance Navigator Control Navigating the Controls 3. TYPES OF NAVIGATOR CONTROLLER MODEL Use these pictures to identify which model you have. WALL MOUNTED CONTROL This model is mounted permanently in the cradle on your wall. No batteries are required. Power is supplied via the same cable that takes the controller's signals to your heating and / or cooling appliances.
Multi-Appliance Navigator Control Navigating the Controls 4. FEATURES OF THE NAVIGATOR CONTROLLER 1. TEMPERATURE SENSOR It Measures the room temperature for thermostatic operation (REMOTE SHOWN). 2. LCD DISPLAY Displays operational status of mode, time, day, room temperature, set temperature, temporary temperature, fan speed, batteries and programming. 3. SOFT TOUCH BUTTONS 8 button layout 4. NAVIGATOR CONTROL CRADLE • • Fixed to the wall to permanently mount the LV wall control.
Multi-Appliance Navigator Control Navigating the Controls 5. USING THE 8 BUTTONS The following explains the function of each of the button: ON/OFF • Turns your heating and / or cooling appliances ON and OFF. BUTTONS • Press & hold UP/DOWN button to increase or decrease settings. • Or press & release UP/DOWN buttons to increase or decrease one point at a time. Settings include day, time, temperature, fan speed. • The UP/DOWN buttons are also used to select the different zones or programs available.
Multi-Appliance Navigator Control Navigating the Controls SETUP • The SETUP button is used to configure the Navigator Controller in either the ON or OFF condition. It allows time setting, program and advanced setup. The advanced setup will only be allowed if the Navigator Controller is in the OFF condition. ENTER • Press and release the ENTER button to save settings when in SET TIME, PROGRAM mode and ZONE setting. • Press and release the ENTER button to immediately send instructions. 6.
Multi-Appliance Navigator Control Navigating the Controls appliances will be hidden and not displayed on your Navigator Controller, therefore some menu items shown in this instruction may not appear. 9. SETTING DAY AND TIME On first power up or reset, the time display will flash 12:00 am and shall remain so until the user sets the time or it receives a set time command from another device. The user can set the time with the controller in an ON or OFF state. To set the time, 1.
Multi-Appliance Navigator Control Navigating the Controls 10. SIMPLE MANUAL OPERATION Here's all you have to do to get the system going (If the installer hasn't already done it for you). To operate the Navigator Controller, 1. Turn the Navigator Controller ON by pressing the ON/OFF button. 2. Press the MODE button to select different modes of operation. 3. Press the or buttons to set the temperature. Your unit will now operate in manual mode. NOTE: When the back light is blue, it is in cooling mode.
Multi-Appliance Navigator Control Navigating the Controls 12. CHILD LOCK Your Navigator Controller provides a special child lock function to protect the current operation or program. To activate CHILD LOCK function at any time, 1. Press and hold the HEAT/COOL and MODE buttons. 2. The child lock is enabled and the lock icon will appear on the display. Any key press will be ignored and the error icon will flash. 3. Press and hold the HEAT/COOL and MODE buttons again to disable the child lock. 13.
Multi-Appliance Navigator Control Navigating the Controls 14. RESETTING THE NAVIGATOR CONTROLLER CAUTION! This will reset the controller to it’s factory default settings and so after a reset, the control may need to be set up again to suit your installation requirements (depending on how your system was first set up). To reset the Navigator Controller to the default setting, 1. Press & hold the ON/OFF button for 3 seconds. 2. Then press the UP, DOWN and SETUP buttons in sequence. 3.
Multi-Appliance Navigator Control Ducted Gas Central Heating DUCTED GAS C ENTRAL HEATING Owner’s Operation and Maintenance Instructions Please keep this important manual in a safe place. It is the owner’s responsibility to ensure that regular maintenance is carried out on the Ducted Gas Central Heater. Failure to do so will void all guarantees beyond statutory and legal requirements.
Multi-Appliance Navigator Control Ducted Gas Central Heating Congratulations on purchasing a BONAIRE Ducted Gas Central Heating system, an exciting new product manufactured by Climate Technologies. Wholly designed and manufactured in Australia, BONAIRE Ducted Gas Central Heaters represent an exciting new development in warm air furnace design. It embodies the latest advances in gas heating technology.
Multi-Appliance Navigator Control Ducted Gas Central Heating 15. SAFETY SAFETY & OWNER RESPONSIBILITY The manufacturer and its service providers reserve the right to refuse service unless safety and accessibility to the unit can be guaranteed in accordance with the installation instructions and Australian Standards. The cost of any extra equipment required to provide access to the unit for servicing is the responsibility of the owner.
Multi-Appliance Navigator Control Ducted Gas Central Heating 16. USING YOUR NAVIGATOR CONTROL There are 2 ways to operate your Navigator Controller. You can use MANUAL CONTROL and select the your mode of operation or you can set a PROGRAM for automatic operation. NOTE: If there is only a central heater fitted in the house, the Navigator Controller will default to Heat. Your Navigator Controller is programmed to automatically detect the appliances connected.
Multi-Appliance Navigator Control Ducted Gas Central Heating • When the room temperature reaches the set temperature the central heater will shut down. • When the room temperature has dropped approximately 0.5º below the set temperature the unit will restart. • As your activities vary, you may find you need different temperature settings, e.g. a temperature comfortable for sitting is usually too warm compared to when you’re moving about.
Multi-Appliance Navigator Control Ducted Gas Central Heating BOOST MODE The BOOST mode operates the heater at maximum power level if the room temperature is below the set temperature. The Navigator Controller turns off the unit when the set temperature is reached. The Navigator Controller turns the unit back on when room temperature drops again. To operate BOOST mode, 1. Turn the Navigator Controller ON by pressing the ON/OFF button. 2.
Multi-Appliance Navigator Control Ducted Gas Central Heating 3. Press the ZONE button to toggle a zone open or closed. Repeat to open or close more zones. The arrow will display under the selected zone on the LCD screen that are set to open / on. 4. Press the ENTER button to exit the Zone setup. Now the Heater operates only in your selected zones. PROGRAM MODE To operate the PROGRAM mode, 1. Turn the Navigator Controller ON by pressing the ON/OFF button. 2.
Multi-Appliance Navigator Control Ducted Gas Central Heating 4. You can set 4 program periods in one single day or day group. To select the program periods press the or button and press the ENTER button. (NOTE: Set these program periods according to the time) 5. The HOURS icon will now be flashing. To set the desired hour button and press the ENTER button to press the or proceed. The MINUTES icon will now flash. Using the or button set the minutes. Press the ENTER button to proceed.
Multi-Appliance Navigator Control Ducted Gas Central Heating 17. HEATER MAINTENANCE WARNING: Before commencing any maintenance work on your unit, isolate the power at the supply (Switch Board). NOTE: It is essential that your central heater be maintained in accordance with this manual. Failure to do so will affect the life of the product and reduce the level of efficiency. ELECTRICAL No general maintenance is required to the electrical system.
Multi-Appliance Navigator Control Ducted Gas Central Heating 19. PROBLEM SOLVING WHAT IF CENTRAL HEATER WILL NOT OPERATE! 1. 2. 3. 4. 5. 6. Question Y/N Solution Has the unit been run since installation? Yes Refer to question 4 No Check the unit is turned on at the power point and the gas shut off valve is turned on. If not call the installer to commission the unit.
Multi-Appliance Navigator Control Dual Cycle Refrigerated Air Conditioning DUAL CYCLE REFRI GERATED AIR CONDITIONING Owners Operating and Maintenance Instructions Please keep this important manual in a safe place. It is the owner’s responsibility to ensure that regular maintenance is carried out on this Dual Cycle Ducted Gas Central Heater / Refrigerated Air Conditioner. Failure to do so will void all guarantees beyond statutory and legal requirements.
Multi-Appliance Navigator Control Dual Cycle Refrigerated Air Conditioning 20. GENERAL INFORMATION IMPORTANT NOTICE If an appropriately qualified and licensed person is not used to install the equipment or if it's not installed according to the guidelines, then Climate Technologies will not accept responsibility for any problems, which occur as a result.
Multi-Appliance Navigator Control Dual Cycle Refrigerated Air Conditioning 22. USING YOUR NAVIGATOR CONTROLLER Using your Navigator Controller for manual operation of your Refrigerated Air Conditioner is the same as your gas central heater where you want direct control, without programming.
Multi-Appliance Navigator Control Dual Cycle Refrigerated Air Conditioning 5. The Navigator Controller measures the room temperature using a thermostat inside its case. When the room temperature is warmer than the set temp, the Dual Cycle Refrigerated Cooling unit will cycle on. 6. The Navigator Controller will run the Dual Cycle Refrigerated Cooler until it measures temperature 2° below your Set Temp and turn off the Dual Cycle cooling unit. 7. Press the ON/OFF button to switch the cooler OFF. 8.
Multi-Appliance Navigator Control Ducted Evaporative Air Conditioning DUCTED EVAPORATIVE AIR CONDITIONING Owners Operating and Maintenance Instructions Please keep this important manual in a safe place. It is the owner’s responsibility to ensure that regular maintenance is carried out on this Ducted Evaporative Air Conditioner. Failure to do so will void all guarantees beyond statutory and legal requirements.
Multi-Appliance Navigator Control Ducted Evaporative Air Conditioning 24. INTRODUCTION Your ducted evaporative air conditioner is engineered to meet the rigours of our harsh Australian environment. Operated and maintained in accordance with this manual, it will provide you with years of quiet, cool and environmentally friendly operation. Please take the time to read this manual. The principal of your unit is to introduce fresh air, which is washed through the filter pads to provide cool fresh air.
Multi-Appliance Navigator Control Ducted Evaporative Air Conditioning WATER MANAGEMENT All evaporative air conditioners need some water to go to waste to prevent build-up of mineral deposits in the system. Your unit has been supplied with an Aquamiser as well as a bleed control system to provide maximum options for best water management. The correct setting of the Aquamiser and bleed will ultimately govern the life of the unit.
Multi-Appliance Navigator Control Ducted Evaporative Air Conditioning 26. USING YOUR NAVIGATOR CONTROLLER Your Navigator Controller will operate your ducted evaporative air conditioner in 4 ways Manual, Thermo, Boost and Fan. NOTE: Your Navigator Controller is designed to automatically detect the appliances you have installed. Controller options not required for your appliances will usually not be visible on your Navigator Controller display.
Multi-Appliance Navigator Control Ducted Evaporative Air Conditioning BOOST MODE In BOOST mode the cooler runs both the pump and the fan at maximum output level. To use the BOOST mode, • Press the MODE button until the BOOST icon appears on the display and press the ENTER button to select the Boost mode. All the 8 bars are displayed indicating full fan speed. • Press the MODE button again to change to a different mode. FAN MODE The Navigator Controller provides 8 levels of Fan Only operation.
Multi-Appliance Navigator Control Ducted Evaporative Air Conditioning 28. DUCTED EVAPORATIVE AIR CONDITIONER MAINTENANCE GENERAL All BONAIRE Ducted Evaporative Air Conditioners benefit from some general maintenance to ensure continued cooling efficiency and a long life. Maintenance is carried out at the beginning and end of summer to start up and close down your unit.
Multi-Appliance Navigator Control Ducted Evaporative Air Conditioning MOTOR AND FAN Check that the fan spins freely and that there is no build up on the blades. ELECTRICAL No general maintenance is required to the electrical system. A Qualified Electrician should only carry out electrical connections and maintenance. BLEED OFF The bleed rate should be checked to ensure it is adequate and that there is no build up of mineral deposits in or on your air conditioner.
Multi-Appliance Navigator Control Ducted Evaporative Air Conditioning 29.
Multi-Appliance Navigator Control Controls- Installation / Setup / Commissioning CONTROL SETUP 30. SETTING UP THE NAVIGATOR CONTROLLER - GENERAL BEFORE STARTING Before attempting to use the setup instructions for the controls system, make sure the transceiver (RF units only) or the low voltage cable is connected, batteries have been correctly installed in the Navigator Controller (RF) and the 240 volt power has been turned on to the product.
Multi-Appliance Navigator Control Controls- Installation / Setup / Commissioning 31. COMMISSIONING CHECK LIST GENERAL All equipment ordered by the customer is installed. The unit is level and secure. The mains and control wiring are complete, the circuit breaker and GPO are turned ON. All Controller functions for the appliance operate. All electrical or gas connections are to manufacturers specifications and the relevant electrical or gas standards and codes.
Multi-Appliance Navigator Control Controls- Installation / Setup / Commissioning Fan speed settings are correct. Burner pressure is correct. Mounting pad/platform complies with requirements / codes. Internal unit access platforms & service light fitted and complies with codes. DUAL CYCLE REFRIGERATED AIR CONDITIONING UNIT Unit Foundation correct and Condenser unit is level Leak test performed System vacuumed down Condenser service valves opened.
Multi-Appliance Navigator Control Warranty – Australia ONLY WARRANTY IMPORTANT Please read this warranty information and complete the Dealer/Product information on the following page. KEEP this with your original purchase documents for any claim under warranty. Firstly refer to your owners manual to ensure you have followed the correct operating procedures of your product, and refer to the trouble shooting guide to assist solving any problems you may have. 1.
Multi-Appliance Navigator Control Warranty – Australia ONLY and the owner will be responsible for all labour charges incurred for the part to be fitted by a qualified person. Labour warranty as prescribed in the following table is void in this situation. EXCLUSION TO WARRANTY • Consumable items subject to wear and tear such as filter pads, drive belts and bearings are not covered by this warranty.
Multi-Appliance Navigator Control Warranty – Australia ONLY PERIODS OF WARRANTY – YEARS BY PRODUCT AND APPLICATION: DUCTED GAS HEATING Unit Components RESIDENTIAL Parts Labour COMMERCIAL Parts Labour Heat Exchanger 10 3 2 2 Burner 10 3 2 2 **All other components 3 3 1 1 ** Return air filter/s and zone motors are field supplied and therefore are not covered by the above warranty periods.
Multi-Appliance Navigator Control Warranty – Australia ONLY WARRANTY ON REPLACEMENT PARTS: Parts replaced under warranty are warranted for the balance of the original warranty period. PROOF OF PURCHASE: It is important that the name of the Dealer or Retailer from whom you purchased your product and the name of the installer are recorded on this page. The installer is responsible for the correct installation, start up and demonstrating the operation of this product.
Multi-Appliance Navigator Control Service SERVIC E SERVICE CENTRES: Only qualified service personnel should conduct any service work carried out on your ducted BONAIRE Heating and Cooling system. It is important that periodical service is carried out on your product to ensure your will receive the efficiency benefits the product provides. For Metro Service only ring the numbers below. South Australia 1300 665 087 Email: saservice@climtech.com.
Manufactured by Climate Technologies ABN 13 001 418 042 26 Nylex Avenue Salisbury, SA 5108 Australia www.climatetechnologies.com.
