Instruction Manual Black Radiant Heater HEEL-1898 Please read these Instructions carefully before using your new heater
@ Although the patio heater is waterproof, do not use when raining or in wet conditions. ® Never connect the power cable from the electrical supply, when the patio heater is not in use. Care and maintenance + When disconnected from the electrical supply, clean the surface of the patio heater with a damp doth. Never use corrosive or solvent cleaners or immerse in water.
® The panel control: Headdress mode Chezigeswodking mos Blu: 750W Blue: 15000 Blue: timer On/Off Receiver ® The remote control: T50W/1500W Timer 16 Unpack the heater to make sure that all the rems are present and that there are no components left in the box and that the heater head is free from any packing material. Using the detailed drawing follow the steps to assemble your heater. Do not connect the heater to the electrical supply until all the assembly Is complete.
involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and dean the appliance or perform user maintenance. Accessories REF. | Name Qty | REF. | Name Qty 1 | Bracket Part Screws M4*8 2 Anchor bolt . 2 M6*50 4 8 | Screws 2 3 | Screws M6*10 4 9 M6 spanner 1 4 racketeer hexagonal 1 wrench Security screw 5 M6E*10 1 11 | Remote control 1 6 | Bracket Part Chain 2 Operation ® The switch on the heater is used to control the Heater.
29. Don't use this heater in place where causticity or volatile air exists, such as dust, steam, gas, etc. 30. Don't use this heater as a cloth drier or towel drier. 31. Don't use this heater as a sauna heater. 32. Don't use this heater in place of animal propagating and raising. 33. Don’t immerse this heater into water for cleaning. 34. The heater should be plugged in a socket, which is easily visible and reachable. 35.
Installation te Wall ® When mounting the heater to a wall, ensure hinges are on the underside so that the lid tilts down in the open position. ¢ Minimum required distances: a) 19.69in (0.5m) from the side wall. b) 19.69in (0.5m) from the ceiling. c) Installation height above 5.91ft Ceiling 5 bzl Installation to Ceiling ® Minimum required distances: d) 9.84in (0.25m) from the side wall e) Minimization (0.5m) from the ceiling (range: 19.69in (0.5m) -29.53in (0.75m) ) f) Installation height above 6ft {1.
Caution Some parts of this product can become very hot and cause bums. Particular attention has to be given where children and vulnerable people are present. 1. Mount the heater outside or in a large open area and well away from any obstructions such as branches or where the heater is near any objects that can be affected by heat, such as furniture, curtains or other inflammable objects (minimum distance 3.28ft/ 1m). 2. Do not position immediately above or below an electrical socket. 3.
Assembling Process for wall mount Preparation stage: Please remove the four M6*10 Screws on the heater, and use them for Step 2 Step 1: Assemble the bracket. (D), Do not tighten the four M6*10 screws @, reserve 2-3 mm of gap for step 4. Step 2: Hook the carbine at the end of the chains 2 through the holes of the Brackets .The length adjustment range of two Chains@ are between 19.69in (0.5m) to 29.53in (0.75m).
Assembling Process for ceiling mount Preparation stage: Please remove the four M6*10 Screws on the heater, and use them for Step 1. Step 1: Adjust the four sliders which inside the track. The distance between the sliders should be between 14.96in (0.38m) to 31.02in (0.78m). Attach the Brackets with four M6*18 screws, tighten them with L ‘hexagonal wrench @ . 10 Step 2: Install the bracket on the back of the heater. Adjust the four sliders inside the track to the middle of the heater.
Step 4: Put the heater on the wall, slide it into bracket part 1 Step 5: Please tighten the M6*10 security screw®) to avoid accidents MEX 10 Security Resew Complete!
