TV3500
SUMMARY Getting Start ---------------------------------------------------------------------3 Description of headset ---------------------------------------------------------3 Description of base -------------------------------------------------------------4 Description of remote control ------------------------------------------------5 How to install Amplicomms TV3500 -----------------------------------------5 Connecting the base ------------------------------------------------------------5 Base set up ----
Getting Start Box contents 1 headset with rubber ear buds size “S“ (small) 1 additional pair of rubber ear buds size “L“ (large) 1 base 1 infrared remote control 1 power adapter for the base 1 optical TOSLINK Digital Audio cable (with plastic protection) 1 analog audio cable (both ends with 3.5 mm jack stereo plug) Multi-language user guides 2 AAA size batteries for remote control English • • • • • • • • • Description of headset 1 Right Left 2 4 3 1. Left / Right earpiece 2. LED indicator 3.
Description of base Base top view 5 6 1 2 3 4 1. Charging cradle 2. Power LED indicator 3. Input LED indicator ( 3 = Microphone, 2 = Analog input, 1 = Optical input/ TOSLINK ) 4. Battery low LED indicator 5. Microphone hole 6. Remote control support Base rear view 11 7 10 7. 8. 9. 10. 8 9 Power supply socket Analog Audio In Socket (3.5 mm) Optical Audio In Socket TOSLINK 3 = Microphone, 2 = Analog input (3.5mm), 1 = Optical input/TOSLINK Aux Switch 11.
Description of remote control + + 1 English 2 3 1. Volume control 2. Headset left/right balance 3. Equalizer ( Sound Clarity mode ) How to install Amplicomms TV3500 Connecting the base 1. Connect the power adapter to the DC input socket located on the base rear panel. 2. Connect the power adapter provided to an electrical outlet. 3. Connect the base to your audio source.
3.a. Using the analog audio cable. Connect one side of the analog cable to the base and the other side to the analog audio output TV/Hifi socket. You may have to purchase adaptor plugs if your TV/Hifi output socket has no 3.5mm audio output (see drawings below). Then on the base, move the switch (AUX) on position 2 = Analog input. Note : Adaptor plugs are not provided 3.b Using the optical audio cable Connect one side of the optical cable to the base and the other side to the TV audio optical output.
Base set up Changing the rubber ear buds 1. For optimum user experience, we have provided 2 sizes of ear buds. Large and Small. If the small size fitted to the headset does not suit you, please try the alternative large size ear bud supplied in the box. 2. For changing the ear buds pick the mounted ear buds at the end and gently pull them out. Then position the alternative ear buds onto the “open ends” and let them snap into the place. Installing batteries in the remote control 1.
Operation Important: Hearing damage due to high volumes! This headset allows you to set higher volumes than conventional headset (up to 125 dB!). This can cause hearing damage for persons with healthy hearing and especially children. • Do not continuously expose yourself to high volumes. 1. Before using the headset, set the volume on the remote control to a low value. 2. Switch ON the audio source (TV/Hifi). 3. If the headset is OFF, the LED will be OFF.
Confirmation Tone There is a “beep” tone as confirmation for every effective key press on TV3500 remote control. Some special tone will be used for below listed case: Using microphone button In active mode, press the button will switch from TV listening mode to transparency mode. The headset indicator will switch from blue to red. The microphone hole is at the front of the headset to pick up the sounds of your surroundings. Make sure that the microphone opening is not covered!.
Troubleshooting No sound - Ensure that the mains adapter is fully pushed into the power outlet and that its cable is properly connected to the DC IN connector on the base. - Ensure that the headset ON. Either red or blue LED is steady on. - The charge level of the headset battery may be too low. Put the headset on the charging cradle for 2 hours. - Ensure that the TV set, Hi-Fi system or audio device is switched ON and the input source selection/connection is correct (AUX switch).
For users wearing a pacemaker It is recommended that, if you have a pacemaker fitted, you check with a medical expert or your health adviser before using this product. Switch the device OFF immediately if you notice or suspect any adverse effects. Power adapter plug Attention: Only use the power adapter plug supplied since other power adapter plugs could damage the base. Ensure access to the power adapter plug is not obstructed by furniture or such.
Technical data Carrier frequency: 1.9GHz Digital Range: Up to 30 meters (open area) Frequency response: 30 Hz – 20 KHz Max volume: 125 dB Distortion: < 1.5% Signal-to-noise ratio: > 70 dB Operating voltage (Base): 5VDC, 550mA Operating voltage (Headset): 3.7 V, 450 mA Lithium Polymer Battery Operation time: With fully charged battery up to 6 hours Charging time: For empty battery approx. 2.5 hours Weight Headset: 61 g Weight Base: 150 g Warranty Please read carefully the user guide included in this box.
If the returned Product is not covered by the warranty, you will receive a quote from repair that will mention the cost of analysis and transportation costs that you will be charged if you want the Product returned to you. Subject to the legal provisions in force, all warranties other than described herein are expressly excluded.
Environment This symbol means that your inoperative appliance must be collected separately and not mixed with the household waste. Help us preserve the environment in which we live! Conformity The logo printed on the products indicates the conformity with all essential requirements ( FCC Part 15B and 15 D).
FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
