Normandy - Tall 3+3 Mirror Robe Assembly Instructions - Please keep for future reference 355/6324 338/3267 357/5563 Dimensions Width - 149.5cm Depth - 50cm Height - 199.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 108kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you have damaged or missing components, call the Customer Helpline: 08456 400800 quoting the reference numbers below Please check you have all the panels listed below 11 Large Shelf (D2052A) (965 x 467mm) 12 Back Rail (D2053A) (965 x 120mm) 8 Left Side (D2048C) (1978 x 471mm) 14 Plinth (D2054A) (1461 x 80mm) 9 Right Side (D2049C) (1978 x 471mm) 10 Divider (DF1870) (1883 x 469mm) 13 Small Shelf (D2060A) (479 x 467mm) x2 15 Horizontal (DF1871) (468 x 468mm) 17 Mirror Door (DF
Components - Fittings If you have damaged or missing components, call the Customer Helpline: 08456 400800 quoting the reference numbers below Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
If you have damaged or missing components, call the Customer Helpline: 08456 400800 quoting the reference Assembly Instructions numbers below Step 1 B Prepare the 3 drawer fronts B B Screw 2 metal dowels B into each of the drawer fronts 1 . 1 x3 Note: Tighten the metal dowels up fully against the panels. Step 2 Prepare the drawer sides C Insert a small locking nut C into the hole shown on the left drawer side 2 and the right drawer side 3 .
Assembly Instructions Step 4 Fit the drawer base Slide the drawer base 5 down the grooves in the drawer sides 2 and 3 and down into the groove in the drawer front 1 . 5 x3 3 2 1 Step 5 Fit the drawer back Fit the drawer back 4 between the drawer sides 2 and 3 . Make sure that the drawer base 5 fits into the groove in the drawer back 4 . Hold the drawer back 4 in position and tap the knock-in pegs L through the holes in the drawer sides 2 and 3 .
Assembly Instructions Step 8 Prepare the divider Finished front edge H U a: Place a runner U on the divider 10 . Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw H . a: 10 H b: Slide the runner back the other way and fit the 2nd screw H into the corresponding hole in the divider 10 . U H H U Finished front edge U Fit 3 hinge plates R onto the divider 10 , making sure that the slot is facing towards the finished front edge.
Assembly Instructions Step 9 D Prepare the horizontal A D D Insert 4 large locking nuts D into the horizontal 15 . D 15 Tap 2 wooden dowels A into the horizontal 15 . A Finished front edge Step 10 B Fit the horizontal to the divider D Push the horizontal 15 onto the divider 10 . 10 Use a screwdriver to tighten the 2 large locking nuts D fitted to the horizontal 15 . Finished front edge 15 Note: Turn the large locking nuts D as far as they will go - more than 1/2 a turn.
Assembly Instructions Step 12 Fit the small divider to the horizontal Push the small divider 16 onto the horizontal 15 . 15 Use a screwdriver to tighten the 2 large locking nuts D fitted to the horizontal 15 . 16 D Step 13 A D Prepare the base Insert 4 large locking nuts D into the base 7 . p in la ch ip Tap 2 wooden dowels A into the base 7 .
Assembly Instructions Step 15 R Prepare the left side D Screw 5 metal dowels B into the left side 8 . Fit 4 hinge plates R onto the left side 8 , making sure that the slot is facing towards the finished front edge. R Finished front edge B A D R B R B R B B 8 Insert 2 large locking nuts D into the left side .8 . Tap a wooden dowel A into the left side 8 . Step 16 D Prepare the right side D R Screw 4 metal dowels B into the right side 9 .
Assembly Instructions Step 17 Fit the right side to the base Push the right side 9 onto the base 7 . 9 Use a screwdriver to tighten the 2 large locking nuts D fitted to the base 7 . Step 18 Prepare the 2 plinths D A x2 in la p Insert 2 large locking nuts D into each of the plinths 14 . e ac D A Finished top edge D in la p o b ip ch Insert 2 large locking nuts D into the back rail .12 . rf A Step 19 Prepare the back rail su 14 Tap 2 wooden dowels A into each of the plinths .14 .
Assembly Instructions Step 20 Fit the back rail and the plinths Push the back rail 12 onto the divider 10 . 9 10 Finished top edge in la p d ar o b ip ch Use a screwdriver to tighten the large locking nut D fitted to the back rail 12 . a rf su ce 12 in la p a rf su 14 d ar o b ip ch Push each plinth 14 onto the right side 9 . ce in la p b ip ch a rf su 14 d ar o Use a screwdriver to tighten the large locking nut D fitted to each plinth 14 .
Assembly Instructions Step 22 B B Prepare the top B Screw 6 metal dowels B into the top 6 . B B B 6 Rounded front edge Step 23 Fit the top and plastic nails Push the top 6 onto the assembly. Use a screwdriver to tighten the 6 large locking nuts D fitted to the left side 8 , right side 9 and divider 10 . 6 9 10 O 8 14 O O 14 O Tap 2 plastic nails O into the bottom edge of each of the sides 8 and .9 . O O Tap 1 plastic nail O into the bottom edge of each plinth .14 .
Assembly Instructions Step 24 Fit back panels a: The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y a: Square up the unit by making sure that measurement x:x equals y:y. Place the small back 21 and large back 22 , coloured surface facing down, onto the unit as shown. Make sure that the 2 backs are pushed up tight against each other and that they meet in the centre of the divider’s back edge.
Assembly Instructions Step 25 x4 a: Fit the hanging rails You can fit the 2 long hanging rails 19 and 2 short hanging rails 20 using any of the positions shown opposite. x8 a: G 19 M M Note: The short rail at position 4 is used for shoe storage. Insert 2 rail holders M for each of the 4 rails and then secure them with screws G . Push the hanging rails 19 and 20 down into the rail holders M .
Assembly Instructions Step 26 Small shelf Position 1 Fit the shelves Insert 4 shelf studs N at position 1 or 2 for the large shelf 11 and the small shelf 13 . Lower the large shelf 11 and the small shelf 13 down onto the shelf studs N . Large shelf Position 1 N x4 Small shelf Position 2 N x4 Large shelf Position 2 N x4 13 N x4 11 Step 27 G Prepare the mirror door and the 2 plain doors Push fit 3 hinges T into the mirror door 17 . G Push fit 4 hinges T into each of the plain doors .18 .
Assembly Instructions Step 28 a: R onto the front part of the hinge plate R . The recess at the bottom of screw B goes into the slot in the hinge plate. b: Keep the hinge B c: T d: R R T T B T FLAT against the hinge plate R as you slide it across as far as it will go. Tighten screw A. c: The hinge T A Note: The easiest way to attach each door 17 and .18 is to fit the top hinge first, then align and fit the other hinges.
Assembly Instructions Step 29 Adjust the doors if needed a: a: Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown. b: A A b: Height adjustment. Loosen screws A on hinge plates and move door up or down as required. Retighten screw A. c: B c: Forward and Back adjustment.
Assembly Instructions Step 30 Wall fixing (not supplied) Fit the overbalance protector To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by use of the overbalance protector kit .Q fitted to the unit or, an alternative fixing method of your choice. Wall fixings are not supplied as they will need to suit the wall type. Washer Washer Screw (not supplied) Screw Q Strap Q N Note: Take care when drilling the wall that you do not drill into any pipes, wires etc.
Assembly Instructions Step 31 Assembly is complete Warning: The unit is heavy. Lift with care. IMPORTANT INFORMATION ABOUT THIS PRODUCT This product complies with the requirements of BS 7449:1991 and has been manufactured by DECORATIVE PANELS FURNITURE LTD, TEESSIDE INDUSTRIAL ESTATE, THORNABY-ON-TEES, CLEVELAND, TS17 9LT. The product code for this unit and the item code(s) for the glass components are listed in the Assembly Instructions along with a description of the type of glass used.
