Installation Guide

ManualsBrandsAmerican Standard ManualsBathTownsend 2-Handle Deck-Mount Roman Tub Faucet with Personal Hand Shower in Polished Nickel

- 1 -

Product names listed herein are trademarks of AS America, Inc.

Thank you for selecting American Standard...

the benchmark of ﬁne quality for over 100 years.

To ensure that your installation proceeds smoothly-please read

these instructions carefully before you begin.

M965723 Rev. 1.1 (7/16)

SPOUT ASSEMBLY

TOWNSEND

DECK MOUNT BATH FILLER

INSTALLATION

INSTRUCTIONS

7353.900

7353.901

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

*Hex Key

Certied to comply with ANSI A112.18.1M

CAUTION

Turn off hot and cold water

supplies before begining.

• Install RING WASHER (1) into spout base recess. Check

that O-RING (2) on end of SPOUT SHANK (3) is in place.

Insert SPOUT SHANK (3) through center hole on mounting

surface.

• Assemble RUBBER WASHER (4) and BRASS WASHER (5)

and LOCKNUT (6) onto SPOUT SHANK (3). Align SPOUT

ASSEMBLY and from underside of ledge secure SPOUT

ASSEMBLY into position with LOCKNUT (6) seated into

RETAINING WASHER (5).

*Supplied with Fittings

434 mm

(17")

280 mm

(11")

253 mm

(10")

116 mm

(5")

215 mm

(8-1/2")

198 mm

(8")

1-1/2

MAX.

(38 mm) MAX.

1-3/16" MAX.

(30 mm) MAX.

1-3/16

(30 mm) D.

(76mm)

(H)

(C)

1-1/8 D.

MAX.

(305 mm)

1-1/16

(27 mm) D.

3/4-14 MALE

N.P.T. INLETS

99 mm

(4")

102 mm

(4")

RECOMMENDED TOOLS ROUGHING-IN DIMENSIONS

SPOUT BASE RECESS

MOUNTING

SURFACE

SPOUT

ASSEMBLY

Hex Wrench

VALVE INSTALLATION

• Place RUBBER RING (1) into DECK ADAPTER (2).

• Install LOCKNUT (3), RUBBER WASHER (4) and

FRICTION WASHER (4B) onto VALVE BODY (5).

From under side of mounting surface, install VALVE

BODY (5) through valve mounting hole. Threads of VALVE

BODY (5) should extent at least 5/16 of a inch above

mounting surface top. Thread DECK ADAPTER (2) onto

VALVE BODY (5) until snug against internal stop.

If necessary, adjust LOCKNUT (3). Tighten LOCKNUT (3)

with WRENCH (6) supplied.

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 7353.900 7353.901 TOWNSEND® DECK MOUNT BATH FILLER Thank you for selecting American Standard... the benchmark of fine quality for over 100 years. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin. RECOMMENDED TOOLS ROUGHING-IN DIMENSIONS 253 mm (10") 198 mm (8") *Hex Key Flat Blade Screwdriver Certified to comply with ANSI A112.18.
PAGE 2
PREPARE TUBE AND TEE ASSEMBLY • Prepare TUBE and TEE ASSEMBLY (1) to fit center to center VALVE (2) location (between 6-1/2" and 12"). If necessary, cut and/or bend TUBING carefully. Make sure tube bend is close to the TEE (1) so that it will not effect the compression joint at the VALVE CONNECTION. ADJ. 6-1/2" TO 12" 4 3 1 MOUNTING SURFACE 5 3 • Remove COUPLING NUT (3) and FERRULE (4) from each VALVE (2) and slide onto TUBING (5). 4 2 NOTE VALVE inlet is 3/4-inch NPT male.
PAGE 3
5 SERVICE • To change direction of handle rotation, proceed as follows: – Turn valve to OFF position. – Thread counter-clock wise HANDLE BASE (1) to remove HANDLE ASSEMBLY (2) from ESCUTCHEON BASE (3). – Use a flat blade screw driver to remove SPRING CLIP (4). – Lift STOP WASHER (5), turn 90˚ and replace. – Replace SPRING CLIP (4). – Reinstall HANDLE ASSEMBLY (2). 2 1 • If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90˚.
PAGE 4
7 MAKE WATER SUPPLY CONNECTIONS • Connect HOT water supply to LEFT INLET UNION (1) and COLD water supply to RIGHT INLET UNION (2). Pipe connections are 3/4" NPT. Use sealant or Teflon tape on pipe connections. Do not solder directly to valve body. 7 8 3 7A TEST INSTALLED FAUCET 4 COLD HOT • With HANDLES (3) in OFF position, turn on water supplies and check all connections for leaks. 3/4" NPT 1 • Remove AERATOR (4). • Operate both HANDLES (3) to flush water lines thoroughly.
PAGE 5
TOWNSEND® DECK MOUNT BATH FILLER MODEL NUMBER 7353.900 7353.