Installation Guide

ManualsBrandsallen + roth ManualsBathroom & Wall LightingCora 4-Light Nickel Modern/Contemporary Vanity Light

ITEM #1362611

MODEL #VBL17-4BNK

4-LIGHT VANITY BAR

PH19216

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-866-439-9800, 8 a.m. - 6 p.m., EST, Monday - Thursday,

8 a.m. - 5 p.m., EST, Friday.

Purchase Date

ATTACH YOUR RECEIPT HERE

welcoming • sophisticated • inspiring

allen + roth

is a registered trademark

Français p. 10

Español p. 19

For Damp

Location

Summary of content (9 pages)

PAGE 1
welcoming • sophisticated • inspiring For Damp Location allen + roth® is a registered trademark of LF, LLC. All Rights Reserved. ITEM #1362611 4-LIGHT VANITY BAR MODEL #VBL17-4BNK Français p. 10 Español p. 19 ATTACH YOUR RECEIPT HERE Purchase Date Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-866-439-9800, 8 a.m. - 6 p.m., EST, Monday - Thursday, 8 a.m. - 5 p.m., EST, Friday.
PAGE 2
TABLE OF CONTENTS Package Contents ................................................................................................................. 2 Hardware Contents ............................................................................................................... 3 Safety Information ................................................................................................................. 3 Preparation ..................................................................................
PAGE 3
HARDWARE CONTENTS (shown actual size) AA BB Wire Connector Qty. 3 Machine Screw Qty. 2 SAFETY INFORMATION READ AND SAVE THESE INSTRUCTIONS. DANGER • For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to fire, electrical shock or other injuries that could be hazardous or even fatal.
PAGE 4
SAFETY INFORMATION WARNING • DO NOT suspend any fixture by the house wires. A fixture must always be mounted directly to an outlet box or to a mounting plate which is first attached to the outlet box. Wire connectors will not support the weight of a fixture. Suspending a fixture by the house wires and wire connectors will result in the fixture falling, with the possibility of personal injury and the danger of electrical shock or fire.
PAGE 5
PREPARATION Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
PAGE 6
ASSEMBLY INSTRUCTIONS 3. Remove mounting plate (B) from fixture (A) by removing mounting plate screws (C) from the edges of the fixture (A). 3 C A Save mounting plate screws (C) for later use. B C C 4. Attach mounting plate (B) to outlet box (not included) using existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult a licensed electrician before proceeding.
PAGE 7
ASSEMBLY INSTRUCTIONS 5. Unwrap BARE fixture wire from BLACK and WHITE fixture wires. Prepare wires by stripping 3/4 in. of insulation from wire ends using wire strippers (not included). Connect WHITE wire from fixture (A) to WHITE wire from outlet box using existing wire connector or wire connector (AA). Connect BLACK wire from fixture (A) to BLACK wire from outlet box using existing wire connector or wire connector (AA).
PAGE 8
ASSEMBLY INSTRUCTIONS 7. Attach fixture (A) to mounting plate (B) using the mounting plate screws (C) previously removed (Step 3, Page 6). 7 NOTE: Before tightening mounting plate screws (C) completely, use level (not included) to check fixture (A) -- adjust if necessary. C A NOTE: Fixture (A) can be installed with the sockets facing either up or down. B C 8. C 8 Restore power and test fixture (A). If lights do not function, please refer to TROUBLESHOOTING.
PAGE 9
TROUBLESHOOTING WARNING: Before beginning work, shut off the power supply to avoid electrical shock. PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Light does not come on initially or no longer comes on. 1. Power is OFF. 2. Faulty connection. 3. LED component is not working properly. 1. Make sure power supply is ON. 2. Check wiring and all connections. 3. Contact Customer Service. Fuse blows out or circuit breaker trips. 1. Crossed wires. 2. Power wire is grounding out. 1. Check wiring. 2.