.0.1 RANGE HOODS Installation Guide and User Manual Luxury should never be left desired - it’s meant to be attainable.
Registering Your Product Please register your ZLINE appliance to activate your warranty. Begin the simple registration process by scanning the QR code. By registering your appliance, you will have access to: • Technical Support • Warranty Service • Tracking your support inquiries ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing the highest end luxury designs and professional features into everyone's homes.
Often the center attraction of a kitchen, ZLINE range hoods can add surprising value to your property, by providing both an impressive, aesthetic look to your home, excellent ventilation, and additional kitchen lighting. ZLINE range hoods blend superior performance with elegant design. ZLINE motors are incredibly powerful, yet quiet compared to the competitors. This is achieved through the highly durable steel-on-steel construction and unique centrifugal design.
WARRANTY PROPER VENTING REGULATIONS Please verify with your local, city, and state regulations on the proper venting method for your hood. Many agencies have CFM rating specifications for your hood, as well. You may have to purchase additional items on your own to vent the hood in accordance with your local city and state specifications. Our ZLINE dual motor range hoods come with an 8” metal transition piece without a backdraft damper and a piece of 4’ metal ducting.
WARRANTY THIS WARRANTY WILL BE VOID WHEN Product damaged through negligence, improper installation, accident, abuse, misuse, and natural disaster, insufficient or excessive electrical supply. Abnormal mechanical or environmental conditions or any unauthorized disassembly repair, modifications or failure to follow the installation instructions or when product is used commercially or other than its intended purpose or damaged because of improper connection with equipment of other manufacturers.
DISCLAIMER Carefully inspect all items for damages before accepting delivery. Customer should note any damages on the freight bill or express receipt. Request the name and signature of the carrier’s agent and keep a copy to support your claim. Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the carrier and file a claim immediately. Failure to do so may result in the denial of your claim. The carrier will furnish you with necessary forms for filing a claim.
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS 1 WALL RANGE HOOD INSTALLATION 4 WALL CROWN MOLDING INSTALLATION 9 DESIGNER WALL RANGE HOOD INSTALLATION 10 WALL CROWNSOUND® INSTALLATION 15 ISLAND RANGE HOOD INSTALLATION 17 DESIGNER ISLAND RANGE HOOD INSTALLATION 21 ISLAND CROWNSOUND® INSTALLATION 25 UNDER CABINET INSTALLATION 27 RANGE HOOD INSERT INSTALLATION 31 REMOTE BLOWER INSTALLATION 33 BUTTON/CONTROL PANEL OPERATION 35 HOW TO CHANGE PARTS 36 TROUBLES
SAFETY INSTRUCTIONS This is the safety alert symbol. This symbol alerts you to potential hazards WARNING that can hurt you and others. All safety messages will follow the safety alert symbol. READ ALL INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS APPLIANCE. • The installation instructions in this manual are intended for qualified installers, service technicians, or persons with similar qualified background.
SAFETY INSTRUCTIONS • Ducted fans MUST ALWAYS be vented to the outdoors. At the point where the duct work ends, add an external damper to prevent air from entering the home when the hood is not in use. This also prevents small animals and rain water from entering the duct work. • When cutting or drilling into a wall or ceiling, be careful not to damage electrical wiring or other hidden utilities. • Your safety and the safety of others is very important.
SAFETY INSTRUCTIONS • All ZLINE range hoods are ETL and UL listed, ensuring all parts were tested for safety and meet industry standards and regulations. NOTE: This ensures all included plastic ducting pieces were tested for safety and are flame retardant. • Always turn the range hood ON when cooking at high heat or when cooking flaming foods. Use high settings on the cooking range only when necessary. Never leave surface units unattended at high settings.
Wall Hood Installation 36” 30”-36” Height 16”-max 31½” WALL HOOD INSTALLATION 4 Installation Tutorial Video
WALL HOOD INSTALLATION Please unpack your range hood when it is delivered and inspect to ensure all parts are included. 1. 2. 3. Main Hood with All Lights and 4. Baffle Filters Button Banks Pre-Installed 5. Flexible Duct (for 6” or 8”) Adjustable Stainless Steel 6. Packet of Screws and Anchors Chimney Cover 7. Top Mounting Bracket Transition Piece (for 6” or 8”) 8.
WALL HOOD INSTALLATION The recommended height to install your hood is 30˝ minimum and 36˝ maximum above the cooktop. For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of 36˝ and a maximum of 42” above the grill. 1. Find the center of the wall where you are installing the hood. Make sure there is sufficient bracing to hold the weight of the hood. Mark your center line and measure out from the center to find your two mounting points.
WALL HOOD INSTALLATION 5. Install the transition piece securing it with the screws provided. Figure 4 6. Make your electrical and ducting connections. Try and minimize the use of elbows. More elbows and longer runs create higher static pressure. The hood comes with a grounded three prong plug that can be plugged into a 20 amp circuit. The cord is 36” long. Figure 5 7. Connect the ducting to the transition piece using foil-backed tape to hold it into place. Attach the ducting to the range hood.
WALL HOOD INSTALLATION 8. Install the two part chimneys on top of the hood. Slide the inside section up until the vertical vent slots are visible, attach top portion to mounting bracket with screws. Secure lower chimney portion to the hood with screws provided. Figure 6 9. Install the grease cup by sliding into brackets located at the bottom of the motor. Install baffle channel and baffle filters. Not all models include baffle channels. Figure 7 1. Screw 3. Screw 2.
WALL CROWN MOLDING INSTALLATION If using a crown molding, follow instructions before attaching ducting and chimney sections. 1. Attach crown molding bracket to ceiling using hardware provided. 2. Attach ducting and electrical connections. 3. Attach chimney sections to the range hood, then connect to crown molding bracket. 4. Slide crown molding onto crown bracket and secure into place.
Designer Wall Hood Installation 36” 30”-36” Height Max 36” DESIGNER WALL HOOD INSTALLATION 10 Scan Me Installation Tutorial Video
DESIGNER WALL HOOD INSTALLATION Please unpack your range hood when it is delivered and inspect to ensure all parts are included. PARTS SUPPLIED 1. Main Hood with All Lights and 5. Flexible Duct (for 6” or 8”) Button Banks Pre-Installed 6. Packet of Screws and Anchors 2. Chimney 7. Top Mounting Bracket 3. Transition Piece (for 6” or 8”) 8. Crown Molding Bracket 4. Baffle Filters 9. Crown Molding E 10.
DESIGNER WALL HOOD INSTALLATION The recommended height to install your hood is 30˝ minimum and 36˝ maximum above the cooktop. For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of 36˝ and a maximum of 42” above the grill. 1. Find the center of the wall where you are installing the hood. Make sure there is sufficient bracing, such as wooden beams, to hold the weight of the hood. Mark your center line and measure out from the center to find your two mounting points.
DESIGNER WALL HOOD INSTALLATION 5. Make your electrical and ducting connections. Try and minimize the use of elbows. More elbows and longer runs create higher static pressure. The hood comes with a grounded three prong plug that can be plugged into a 20amp. circuit. The cord is 36” long. Figure 5 6. Install the transition piece securing it with screws provided. 7. Connect the ducting to the transition piece using foil-backed tape to hold it into place. Attach the ducting to the range hood.
DESIGNER WALL HOOD INSTALLATION 8. Find the center of the wall where you are installing the hood. Make sure there is sufficient bracing to hold the weight of the hood. Mark your center line and measure out from the center to find your two mounting points. Make sure your mounting points are level when you mark them. It is recommended to install the hood directly into wood supports. Figure 7 9. Mark the mounting points and install the two mounting screws provided leaving the heads out ¼˝ to mount the hood.
WALL CROWNSOUND® INSTALLATION ELECTRIC POWER RATING Frequency: 110V/50 Hz Power: 10W Watch Now Installation Tutorial Video 1. Attach crown molding bracket to ceiling using hardware provided. Figure 1 Figure 1 Attach ducting and electrical connections. Plug the speakers into an outlet behind the chimney. When the connection is successful, a chime will sound. Figure 2 Figure 2 Wall CrownSound® Installation 2.
WALL CROWNSOUND® INSTALLATION 3. Extend the chimney up to the transformer. Slide the crown molding onto the crown bracket and secure into place. The crown should cover the gap. Ensure that it installs properly and is level. Figure 3 Figure 3 4. Open the phone’s Bluetooth settings and find “ZLINE Audio.“ When the connection is successful, a chime will sound. Figure 4 Wall CrownSound® Installation Input 16 Figure 4 Bluetooth crown moldings carry a one year parts warranty.
36” 30”-36” Height 26” - max 39” ISLAND HOOD INSTALLATION Installation Tutorial Video Island Hood Installation Scan Me 17
ISLAND HOOD INSTALLATION Please unpack your range hood when it is delivered and inspect to ensure all parts are included. PARTS SUPPLIED 1. Main Hood with All Lights and 6. Packet of Screws and Anchors Button Banks Pre-Installed 7. Top Mounting Bracket 2. Chimney 8. Crown Molding Bracket 3. Transition Piece (for 6” or 8”) 9. Crown Molding 4. Baffle Filters 10. Grease Cup 5.
ISLAND HOOD INSTALLATION The recommended height to install your hood is 30˝ minimum and 36˝ maximum above the cooktop. For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of 36˝ and a maximum of 42” above the grill. 1. Locate the center above the stove where the hood is to be installed. Ensure that the bracket will be secured to solid wood backing. Attach mounting bracket to the ceiling. 2. Attach the transition piece and ducting to top of the hood. Figure 1 and 2 3.
ISLAND HOOD INSTALLATION 1. Slide chimney pieces over the angle iron on the hood. Pull the electrical plug to the top of the chimney sections. Figure 4 2. Lift the hood to attach the angle iron to the ceiling bracket. Use screws provided to attach. 3. Make your electrical and ducting connections. Use rigid ducting wherever possible. Try and minimize the use of elbows. More elbows and longer runs create higher static pressure. No more than two to three elbows are recommended.
Scan Me Installation Tutorial Video Designer Island Hood Installation 36” 30”-36” Height Max 36” DESIGNER ISLAND HOOD INSTALLATION 21
DESIGNER ISLAND HOOD INSTALLATION Please unpack your range hood when it is delivered and inspect to ensure all parts are included. PARTS SUPPLIED 1. Main Hood with All Lights and 6. Packet of Screws and Anchors Button Banks Pre-Installed 7. Top Mounting Bracket 2. Chimney 8. Crown Molding Bracket 3. Transition Piece (for 6” or 8”) 9. Crown Molding 4. Baffle Filters 10. Grease Cup 5.
DESIGNER ISLAND HOOD INSTALLATION The recommended height to install your hood is 30˝ minimum and 36˝ maximum above the cooktop. For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of 36˝ and a maximum of 42” above the grill. 1. Locate the center above the stove where the hood is to be installed. Ensure that the bracket will be secured to solid wood backing. Attach mounting bracket to the ceiling. Figure 1 2. Attach the transition piece and ducting to top of the hood.
DESIGNER ISLAND HOOD INSTALLATION 6. Slide chimney pieces over the angle iron on the hood. Pull the electrical plug to the top of the chimney sections. Figure 4 7. Lift the hood to attach the angle iron to the ceiling bracket. Use screws provided to attach. 8. Make your electrical and ducting connections. Use rigid duct wherever possible. Try and minimize the use of elbows. More elbows and longer runs create higher static pressure.
ISLAND CROWNSOUND® INSTALLATION ELECTRIC POWER RATING Frequency: 110V/50 Hz Power: 10W Watch Now Installation Tutorial Video 1. Attach crown molding bracket to ceiling using hardware provided. Figure 1 Screw: A/C/D Screw:A/C/D Screw: E Screw:E Figure 1 2. Screw:A/C/D Attach ducting and electrical connections. Plug the speakers into an outlet behind the chimney. When the connection is successful, a Screw:E chime will sound.
ISLAND CROWNSOUND® INSTALLATION 3. Extend the chimney up to the transformer. Slide the crown molding onto the crown bracket and secure into place. The crown should cover the gap. Ensure that it installs properly and is level. Figure 3 4. Figure 3 Open the phone’s Bluetooth settings and find “ZLINE Audio.“ When the connection is successful, a chime will sound.
30” 30”-36” Height UNDER CABINET INSTALLATION Installation Tutorial Video Under Cabinet Installation Scan Me 27
UNDER CABINET INSTALLATION Undercabinet UndercabinetRecirculating RecirculatingKit Kit RECIRCULATING KIT Step 1: 1:Open package, locate all neccessary hardware. Included Step Open package, locate all neccessary hardware. Included should be Open package, locate all necessary hardware. Included shouldshould be 4 be screws 1. 4 screws withwith 4 washers. 4 screws 4 washers. with 4 washers. Step 2: 2:LineLine up the recirculating kit with the the toptop of the range hood.
UNDER CABINET INSTALLATION PREPARATION • Decide the location of the venting pipe from the hood to the outside. • Check hood for clearance. • A straight, short vent run will allow the hood to perform more efficiently. • Try to avoid as many transitions, elbows, and long runs as possible. This may reduce the performance of the hood. • For installing under the cabinet with recessed bottom, attach 4-inch wide wood filler strips (not provided) on each side.
UNDER CABINET INSTALLATION If you need to convert your under cabinet range hood to rear ducting, use the following instructions. Please note that converting the undercab to rear ducting is a modification of the standard hood and part of the installation process. It is recommended that the hood is inspected before this procedure. Only certain undercab models allow for rear ducting. Contact us at 1-614-7775004 for more information on compatible models. 1.
36” 30”-36” INSERT INSTALLATION Insert Installation Installation Tutorial Video 31
INSERT INSTALLATION When installing a range hood insert, it is recommended to install the unit at a minimum of 30˝ from the cooktop. For outdoor range hood inserts it is recommended to install the unit at a minimum of 36˝ and a maximum of 42” from the grill top. 1. Unpack contents of the hood. Attach transition piece and ducting to the top of the range hood insert. Figure 1 2. Using L brackets and screws provided, attach L brackets to each side of the insert. 3.
REMOTE BLOWER INSTALLATION When installing your new remote blower type range hood, follow the instructions for the type of hood you are installing. Remote blowers are available with wall, island, under cabinet, and insert range hoods. Make certain to connect the electrical cord to the hood and plug the blower motor in to test the unit. 1. Run duct work into the area that you will install the remote from your range hood. 2. Fasten ducting to the range hood using a hose clamp and silver/duct tape. 3.
REMOTE BLOWER INSTALLATION Unit Connection Cord The Remote Blower is designed for our Remote Range Hoods. This unit is installed remotely in the interior of your home. This provides venting, but with reduced noise. T85 Remote Blower—Single Motor (This Blower must be used with Remote Blower Hood) Airflow: 400 (CFM) Noise Level: 1.2 / 2.6 / 4.2 / 6.5 (Sones) Remote Blower Installation Dimensions: 26.14 x 14.
Button Control Panel Operational Manual ! OPERATION ! ! Power Power-Off Delay Low Speed Medium 1 Speed Light High Speed Medium 2 Speed Blower Speed Indicator Button functions Power: Turn ON/OFF the range hood and activate power-off delay timer. Light: Turn ON/OFF (Some models will have bright, dim, and OFF settings.) Blower Speed Indicator: Shows current blower (motor) speed (1-4). 1- Low Speed: Light frying/boiling. 2 - Medium Speed: Frying/wok cooking/heavy boiling.
CHANGING PARTS HOW TO CHANGE OUT THE BUTTON PANEL 1. Remove baffle/aluminum filters. 2. Locate back of button panel. 3. Remove screws from each side of the button panel. 4. Disconnect button panel from cord connecting to circuit board. NOTE: Never work on or clean the range hood while power is ON. Always unplug the unit or switch the electrical breaker to the off position.
CHANGING PARTS HOW TO REPLACE THE CIRCUIT BOARD 1. Turn the power off at the breaker and unplug the Range Hood. 2. Remove all screws from the top of the circuit board cover. 3. Take a picture of the wiring layout (this will help you put the circuit board back together properly). 4. Remove the wiring connected to the circuit board. 5. Remove the screws from the circuit board. 6. Replace the wiring and screws to reassemble the new circuit board per the diagram below.
CHANGING PARTS REPLACING THE LIGHT BULBS IN YOUR RANGE HOOD 1. Remove baffles. 2. Squeeze the old LED light casting out until it falls out of the socket. 3. Disconnect the plug wires from the light wire. 4. Reconnect the LED plug into the light wire. 5. Press light assembly into the socket. NOTE: Never work on or clean the range hood while power is ON. Always unplug the unit or switch the electrical breaker to the off position.
CHANGING PARTS PROFESSIONAL SERIES BAFFLE FILTER CHANGE Covering Models 696, 697, 697i (Island), KECOM, KECOMi (Island), 695, 698, and 721 Inserts Professional series hoods are equipped with 2 removable dishwasher safe baffle channels (one for series 695 and 698 inserts) that the baffle filters rest in. To install the channels, place inside the hood, right under the front and back edges of the hood. The channel is kept in place by installation pieces on the sides and back of the baffle channel.
CHANGING PARTS BAFFLE FILTER The baffle filter is equipped with a knob. To remove from the hood, pull back toward the wall and down.
CHANGING PARTS CHANGE/REPLACE CAPACITOR: 1. Remove screws from the circuit board cover. 2. Remove screws from compactor. 3. Remove both wired connections from the capacitor. 4. Connect new capacitor with wire connectors. 5. Replace screws in cover. 6. Repeat operation if dual motor. NOTE: Some units have more than one motor. If you have a unit with dual motors, there will be two capacitors. NOTE: Never work on or clean the range hood while power is ON.
CHANGING PARTS REPLACE OR CHANGE CHARCOAL FILTERS: It is recommended to direct vent the hood whenever possible. If your situation does not allow for a direct vent install, carbon filters are available to recirculate the air through your hood. Filter Support Screws 1. Remove the stainless steel or aluminum filters from the bottom of the hood. 2. Locate the existing raised support screws on each side of the internal motor(s). 3.
CHANGING PARTS HOW TO CLEAN, INSTALL, OR REPLACE THE GREASE CUP: A removable grease cup is provided to catch any excess grease at the bottom of the motor. Remove it every 2 to 3 months, wash it, then re-install it. NOTE: Never work on or clean the range hood while power is ON. Always unplug the unit or switch the electrical breaker to the off position.
CHANGING PARTS REPLACE OR CHANGE TRANSFORMER: 1. Remove the screws from the transformer. 2. Remove the two connections to the lights. 3. Remove the two wired connections from the circuit board (you must remove the circuit board cover). 4. Install the new connections from your new transformer (be certain the correct wires are connected). 5. Reinstall the cover for the circuit board with screws. 6. Replace all screws in the transformer. 7. Reconnect the lights to the transformer.
CHANGING PARTS SINGLE MOTOR ELECTRICAL DIAGRAM Single Motor Electrical Diagram 45
CHANGING PARTS Double Motor Electrical Diagram DUAL MOTOR ELECTRICAL DIAGRAM 46
TROUBLESHOOTING Where are ZLINE products manufactured? All ZLINE products are manufactured in ZLINE facilities overseas, including: Germany, Italy, and China. Are ZLINE range hoods considered type 1 or type 2? Type 1 - Range hoods that are used with appliances that produce grease and smoke. Are ZLINE products meant for residential or commercial use? Residential use. Why is my range hood white? This is a protective layer that is placed on all of our range hoods to prevent shipping damage.
TROUBLESHOOTING How loud is the range hood? A sone is measure of loudness, the higher the sone rating, the louder the sound of the hood. The sound of one sone is comparable to that of a quiet refrigerator. Keep in mind that other factors such as the size of the blowers can affect the loudness of the range hood. The higher the CFM, the louder the sone rating will be.
TROUBLESHOOTING What type of motor is in the range hoods? Our hoods have a squirrel cage motor. Is the width of my range hoods description, the actual size? No, the actual size of the range hood will be slightly less than the generic description of the range hood. For instance: a 30˝ range hood will most likely be 29-1/2˝. Refer to your particular model for the exact width.
TROUBLESHOOTING My hood is operating, but the air is moving slower than normal. Check the filter for buildup and clean or replace it if needed. If the difficulty still persists, check for obstructions in the ductwork. A common obstruction is buildup in the roof or wall cap, such as: bird nests or other debris. What is make-up air? When the range hood ventilates the air out of the room, the air vented must be replaced, this is called make-up air. We do not currently provide a make-up air unit.
TROUBLESHOOTING My range hood will not operate. 1. Check that there is power to the range hood. The most common issue is that the circuit breaker is off or the fuse has blown. 2. Make sure the speed has been selected at the range hood controls. 3. Turn off the power to the range hood and check that all wires are properly connected. Refer to your specific model’s installation instructions for proper wiring. My hood is making a rattling noise. This is probably attributed to one of the following: 1.
TROUBLESHOOTING My range hood is not pulling.
TROUBLESHOOTING Noisy Motor • Were the fan speeds checked fan speeds prior to installation? • Is the ducting clear? • Check to make sure motor is attached to housing • Is the 6” back draft damper on transition piece functioning properly (760 CFM hood?) Does it open when the hood is engaged? • If it is stuck, it will sound like motor noise but it’s really the damper • Was a damper installed on the roof or side vent? • Check that the damper is fully functioning by engaging the hood and checking if it opens
MOUNTING SPECIFICATIONS C B 54 Model Numbers A B C D 432-30 19 116 " 20 1116 " 29 3 4 " 8" 432-36 19 116 " 26 1116 " 35 3 4 " 8" 432-42 19 116 " 32 1116 " 41 3 4 " 8" 432-48 19 116 " 38 1116 " 47 3 4 " 8" 432 432 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 433-30 19 116 " 20 1116 " 29 3 4 " 8" 433-36 19 116 " 26 1116 " 35 3 4 " 8" 433-42 19 116 " 32 1116 " 41 3 4 " 8" 433-48 19 116 " 38 1116 " 47 3 4 " 8" 433 433 A D 55
MOUNTING SPECIFICATIONS C B 56 Model Numbers A B C D 435-30 19 116 " 20 1116 " 29 3 4 " 8" 435-36 19 116 " 26 1116 " 35 3 4 " 8" 436-30 19 116 " 20 1116 " 29 3 4 " 8" 436-36 19 116 " 26 1116 " 35 3 4 " 8" 435 436 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 455-30 17 1116 " 9 1116 " 13 5 16 " 6" 455-36 17 1116 " 9 1116 " 13 5 16 " 8" 455-42 17 1116 " 9 1116 " 13 5 16 " 8" 455-48 17 1116 " 9 1116 " 13 5 16 " 8" 455 455 A D 57
MOUNTING SPECIFICATIONS C B 58 Model Numbers A B C D 476-30 17 1116 " 9 1116 " 13 5 16 " 6" 476-36 17 1116 " 9 1116 " 13 5 16 " 8" 476-42 17 1116 " 9 1116 " 13 5 16 " 8" 476-48 17 1116 " 9 1116 " 13 5 16 " 8" 476 476 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 477-30 17 1116 " 9 1116 " 13 5 16 " 6" 477-36 17 1116 " 9 1116 " 13 5 16 " 8" 477-42 17 1116 " 9 1116 " 13 5 16 " 8" 477-48 17 1116 " 9 1116 " 13 5 16 " 8" 477 477 A D 59
MOUNTING SPECIFICATIONS C B 60 Model Numbers A B C D 488-30 19 116 " 20 1116 " 29 3 4 " 8" 488-36 19 116 " 26 1116 " 35 3 4 " 8" 488-42 19 116 " 32 1116 " 41 3 4 " 8" 488-48 19 116 " 38 1116 " 47 3 4 " 8" 488 488 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 587-R-30 15 3 16 " 9 9 16 " 11 1116 " 8" 587-R-36 15 3 16 " 9 9 16 " 11 1116 " 8" 587-R-42 15 3 16 " 9 9 16 " 11 1116 " 8" 587-R-48 15 3 16 " 9 9 16 " 11 1116 " 8" 587-R 587-R A D 61
MOUNTING SPECIFICATIONS C B 62 Model Numbers A B C D 587-30 15 3 16 " 9 9 16 " 11 1116 " 6" 587-36 15 3 16 " 9 9 16 " 11 1116 " 6" 587-42 15 3 16 " 9 9 16 " 11 1116 " 6" 587-48 15 3 16 " 9 9 16 " 11 1116 " 6" 587 587 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 597-R-30 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R-36 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R-42 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R-48 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R-54 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R-60 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R 597-R A D 63
MOUNTING SPECIFICATIONS C B 64 Model Numbers A B C D 597-30 15 3 16 " 9 9 16 " 11 1116 " 6" 597-36 15 3 16 " 9 9 16 " 11 1116 " 6" 597-42 15 3 16 " 9 9 16 " 11 1116 " 6" 597-48 15 3 16 " 9 9 16 " 11 1116 " 6" 597-54 15 3 16 " 9 9 16 " 11 1116 " 6" 597-60 15 3 16 " 9 9 16 " 11 1116 " 6" 597 597 A D
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B Model Numbers A B C D 655-R-30 17 1116 " 9 1116 " 13 5 16 " 8" 655-R-36 17 1116 " 9 1116 " 13 5 16 " 8" 655-R 655-R A D 65
MOUNTING SPECIFICATIONS C B 66 Model Numbers A B C D 655-30 17 1116 " 9 1116 " 13 5 16 " 6" 655-36 17 1116 " 9 1116 " 13 5 16 " 8" 655-42 17 1116 " 9 1116 " 13 5 16 " 8" 655-48 17 1116 " 9 1116 " 13 5 16 " 8" 655 655 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 667-30 17 1116 " 9 1116 " 13 5 16 " 6" 667-36 17 1116 " 9 1116 " 13 5 16 " 8" 667-42 17 1116 " 9 1116 " 13 5 16 " 8" 667-48 17 1116 " 9 1116 " 13 5 16 " 8" 667-54 17 1116 " 9 1116 " 13 5 16 " 8" 667-60 17 1116 " 9 1116 " 13 5 16 " 8" 667 667 A D 67
MOUNTING SPECIFICATIONS C B 68 Model Numbers A B C D 685-30 19 116 " 20 1116 " 29 3 4 " 8" 685-36 19 116 " 26 1116 " 35 3 4 " 8" 685-42 19 116 " 32 1116 " 41 3 4 " 8" 685-48 19 116 " 38 1116 " 47 3 4 " 8" 685 685 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 686-30 19 116 " 20 1116 " 29 3 4 " 8" 686-36 19 116 " 26 1116 " 35 3 4 " 8" 686-42 19 116 " 32 1116 " 41 3 4 " 8" 686-48 19 116 " 38 1116 " 47 3 4 " 8" 686 686 A D 69
MOUNTING SPECIFICATIONS C B 70 Model Numbers A B C D 687-R-30 19 5 16 " 14 14 " 17 7 8 " 8" 687-R-36 19 5 16 " 14 14 " 17 7 8 " 8" 687-R-42 19 5 16 " 14 14 " 17 7 8 " 8" 687-R-48 19 5 16 " 14 14 " 17 7 8 " 8" 687-R 687-R A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 687-30 19 5 16 " 14 14 " 17 7 8 " 8" 687-36 19 5 16 " 14 14 " 17 7 8 " 8" 687-42 19 5 16 " 14 14 " 17 7 8 " 8" 687-48 19 5 16 " 14 14 " 17 7 8 " 8" 687 687 A D 71
MOUNTING SPECIFICATIONS C B 72 Model Numbers A B C D 696-36 14 18 " 7 1116 " 11 14 " 6" 696-R-36 14 18 " 7 1116 " 11 14 " 8" 696 & 696-R 696 & 696-R A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 697-R-30 17 1116 " 9 1116 " 13 5 16 " 8" 697-R-36 17 1116 " 9 1116 " 13 5 16 " 8" 697-R-42 17 1116 " 9 1116 " 13 5 16 " 8" 697-R-48 17 1116 " 9 1116 " 13 5 16 " 8" 697-R 697-R A D 73
MOUNTING SPECIFICATIONS C B 74 Model Numbers A B C D 697-30 17 1116 " 9 1116 " 13 5 16 " 6" 697-36 17 1116 " 9 1116 " 13 5 16 " 8" 697-42 17 1116 " 9 1116 " 13 5 16 " 8" 697-48 17 1116 " 9 1116 " 13 5 16 " 8" 697-54 17 1116 " 9 1116 " 13 5 16 " 8" 697-60 17 1116 " 9 1116 " 13 5 16 " 8" 697 697 A D
MOUNTING SPECIFICATIONS C B A D A B C D 8632-30 27 7 8 " 9 12 " 11 13 16 " 6" 8632-36 27 7 8 " 9 12 " 11 13 16 " 8" 8632-42 27 7 8 " 15 1116 " 18 " 8" 8632-48 27 7 8 " 15 1116 " 18 " 8" 8632 8632 Model Numbers 75
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B A D 76 A B C D 8654-30 17 116 " 9 58 " 13 5 16 " 6" 8654-36 17 116 " 9 58 " 13 5 16 " 8" 8654-42 17 116 " 9 58 " 13 5 16 " 8" 8654-48 17 116 " 9 58 " 13 5 16 " 8" 8654 8654 Model Numbers
MOUNTING SPECIFICATIONS C B A D A B C D 8656-30 17 1116 " 9 1116 " 13 5 16 " 6" 8656-36 17 1116 " 9 1116 " 13 5 16 " 8" 8656-42 17 1116 " 9 1116 " 13 5 16 " 8" 8656-48 17 1116 " 9 1116 " 13 5 16 " 8" 8656 8656 Model Numbers 77
MOUNTING SPECIFICATIONS C B 78 Model Numbers A B C D 9597-30 15 3 16 " 9 9 16 " 11 1116 " 6" 9597-36 15 3 16 " 9 9 16 " 11 1116 " 6" 9597 9597 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D 9667-30 17 1116 " 9 1116 " 13 5 16 " 6" 9667-36 17 1116 " 9 1116 " 13 5 16 " 8" 9667 9667 A D 79
MOUNTING SPECIFICATIONS C B 80 Model Numbers A B C D 9697-30 17 1116 " 9 1116 " 13 5 16 " 6" 9697-36 17 1116 " 9 1116 " 13 5 16 " 8" 9697 9697 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D ART2-30 15 3 16 " 9 7 16 " 11 1116 " 6" ART2-36 15 3 16 " 9 7 16 " 11 1116 " 6" ART2 ART2 A D 81
MOUNTING SPECIFICATIONS C B 82 Model Numbers A B C D BS655N-30 17 1116 " 9 1116 " 13 5 16 " 6" BS655N-36 17 1116 " 9 1116 " 13 5 16 " 8" BS655N-42 17 1116 " 9 1116 " 13 5 16 " 8" BS655N-48 17 1116 " 9 1116 " 13 5 16 " 8" BS655N BS655N A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D BSKBN-24 11 3 4 " 7 116 " 9 18 " 6" BSKBN-30 11 3 4 " 7 116 " 9 18 " 6" BSKBN-36 11 3 4 " 7 116 " 9 18 " 6" BSKBN-42 11 3 4 " 7 116 " 9 18 " 6" BSKBN-48 11 3 4 " 7 116 " 9 18 " 6" BSKBN BSKBN A D 83
MOUNTING SPECIFICATIONS C B 84 Model Numbers A B C D BSKEN-30 12 3 4 " 9 9 16 " 11 5 8 " 6" BSKEN-36 12 3 4 " 9 9 16 " 11 5 8 " 6" BSKEN-42 12 3 4 " 9 9 16 " 11 5 8 " 6" BSKEN-48 12 3 4 " 9 9 16 " 11 5 8 " 6" BSKEN BSKEN A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D KB-24 11 3 4 " 7 116 " 9 18 " 6" KB-30 11 3 4 " 7 116 " 9 18 " 6" KB-36 11 3 4 " 7 116 " 9 18 " 6" KB-42 11 3 4 " 7 116 " 9 18 " 6" KB-48 11 3 4 " 7 116 " 9 18 " 6" KB KB A D 85
MOUNTING SPECIFICATIONS C B 86 Model Numbers A B C D KB2-30 13 3 8 " 7 116 " 9 18 " 6" KB2-36 13 3 8 " 7 116 " 9 18 " 6" KB2-42 13 3 8 " 7 116 " 9 18 " 6" KB2-48 13 3 8 " 7 116 " 9 18 " 6" KB2 KB2 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D KE-30 12 3 4 " 9 9 16 " 11 5 8 " 6" KE-36 12 3 4 " 9 9 16 " 11 5 8 " 6" KE-42 12 3 4 " 9 9 16 " 11 5 8 " 6" KE-48 12 3 4 " 9 9 16 " 11 5 8 " 6" KE KE A D 87
MOUNTING SPECIFICATIONS C B KF, KF1, & KF2 A D 88 Model Numbers A B C D KF-36 12 " 7 116 " 9 18 " 6" KF1-30 13 5 8 " 8 12 " 10 12 " 6" KF1-36 13 5 8 " 8 12 " 10 12 " 6" KF2-30 159 16 " 8 12 " 10 12 " 6" KF2-36 159 16 " 8 12 " 10 12 " 6"
MOUNTING SPECIFICATIONS C B Model Numbers A B C D KL2-30 11 7 16 " 7 116 " 9 18 " 6" KL2-36 11 7 16 " 7 116 " 9 18 " 6" KL2-42 11 7 16 " 7 116 " 9 18 " 6" KL2-48 11 7 16 " 7 116 " 9 18 " 6" KL2 KL2 A D 89
MOUNTING SPECIFICATIONS C B 90 Model Numbers A B C D KL3-30 12 3 4 " 7 116 " 9 18 " 6" KL3-36 12 3 4 " 7 116 " 9 18 " 6" KL3-42 12 3 4 " 7 116 " 9 18 " 6" KL3-48 12 3 4 " 7 116 " 9 18 " 6" KL3 KL3 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D KN-30 12 3 4 " 9 9 16 " 11 5 8 " 6" KN-36 13 7 16 " 9 9 16 " 11 5 8 " 6" KN KN A D 91
MOUNTING SPECIFICATIONS C B 92 Model Numbers A B C D KN6-30 12 7 8 " 9 9 16 " 11 5 8 " 6" KN6-36 13 9 16 " 9 9 16 " 11 5 8 " 6" KN6 KN6 A D
MOUNTING SPECIFICATIONS C B Model Numbers A B C D KZ-30 12 7 16 " 9 9 16 " 11 5 8 " 6" KZ-36 13 5 16 " 9 9 16 " 11 5 8 " 6" KZ KZ A D 93
43 8 " 95 16 " 415 16 " 415 16 " CMBI-655i 33 4 " 45 16 " 8116 " 1014 " 85 8 " 45 16 " 45 16 " 41116 " CMBI-8 9116 " 41116 " 45 16 " 415 16 " 97 8 " 119 16 " CMBI-6 1314 " 93 8 " 41116 " CMBI-6 & CMBI-8 94 45 16 " CMBI-6 & CMBI-8 MOUNTING SPECIFICATIONS 117 16 " 93 8 " 41116 " 203 16 " 1818 " 9116 " 33 4 " 45 16 " 1
45 16 " 33 4 " 8116 " 45 16 " 45 16 " 1014 " 85 8 " 8116 " 45 16 " 45 16 " CMBI-655i 33 4 " 45 16 " 85 8 " 107 8 " 1314 " 93 8 " 41116 " CMBI-6 41116 " 41116 " 117 16 " 93 8 " 41116 " CMBI-655i 95 43 8 " 415 16 " 9 11
Installation Guide and User Manual 1.1.0 www.zlinekitchen.
