.0.
SCAN ME REGISTERING YOUR PRODUCT Please register your ZLINE appliance to activate your warranty. Begin the simple registration process by scanning the QR code. ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath of your dreams is never out of reach. Through our unique designs and unparalleled quality, we’re dedicated to providing you an elevated experience in the heart of your home. With an endless selection of features and finishes, our inspiration is your reality.
WARRANTY WARRANTY PROPER VENTING REGULATIONS THIS WARRANTY WILL BE VOID WHEN Please verify with your local, city, and state regulations on the proper venting method • Product damaged through negligence, improper installation, accident, abuse, for your hood. Many agencies have CFM rating specifications for your hood, as well. You may have to purchase additional items on your own to vent the hood in accordance with your local city and state specifications.
DISCLAIMER Carefully inspect all items for damages before accepting delivery. Customer should note any damages on the freight bill or express receipt. Request the name and signature of the carrier’s agent and keep a copy to support your claim. Upon acceptance of items, owner assumes responsibility for its safe arrival. Report damages to the carrier and file a claim immediately. Failure to do so may result in the denial of your claim. The carrier will furnish you with necessary forms for filing a claim.
SAFETY INSTRUCTIONS TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS 1 This is the safety alert symbol. This symbol alerts you to potential hazards WALL RANGE HOOD INSTALLATION 4 WARNING that can hurt you and others. All safety messages will follow the safety alert symbol. WALL CROWN MOLDING INSTALLATION 9 READ ALL INSTRUCTIONS BEFORE INSTALLING AND OPERATING THIS DESIGNER WALL RANGE HOOD INSTALLATION 10 APPLIANCE.
SAFETY INSTRUCTIONS • Ducted fans MUST ALWAYS be vented to the outdoors. At the point where the SAFETY INSTRUCTIONS • All ZLINE range hoods are ETL listed, ensuring all parts were tested for safety duct work ends, add an external damper to prevent air from entering the home and meet industry standards and regulations. NOTE: This ensures all included when the hood is not in use. This also prevents small animals and rain water from plastic ducting pieces were tested for safety and are flame retardant.
WALL HOOD INSTALLATION WALL HOOD INSTALLATION Please unpack your range hood when it is delivered and inspect to ensure all parts are included. 16”-max 31½” 1. 2. 3. Main Hood with All Lights and 4. Baffle Filters Button Banks Pre-Installed 5. Flexible Duct (for 6” or 8”) Adjustable Stainless Steel 6. Packet of Screws and Anchors Chimney Cover 7. Top Mounting Bracket Transition Piece (for 6” or 8”) 8.
WALL HOOD INSTALLATION WALL HOOD INSTALLATION The recommended height to install your hood is 30˝ minimum and 36˝ maximum 5. Install the transition piece securing it with the screws provided. Figure 4 above the cooktop. For Outdoor (304 Series) hood installation, the unit must be 6. Make your electrical and ducting connections. Try and minimize the use of installed at a minimum of 36˝ and a maximum of 42” above the grill. elbows. More elbows and longer runs create higher static pressure.
WALL CROWN MOLDING INSTALLATION WALL HOOD INSTALLATION 8. Install the two part chimneys on top of the hood. Slide the inside section up until If using a crown molding, follow instructions before attaching ducting and chimney the vertical vent slots are visible, attach top portion to mounting bracket with sections. screws. Secure lower chimney portion to the hood with screws provided. Figure 6 9. Install the grease cup by sliding into brackets located at the bottom of the motor. 1.
DESIGNER WALL HOOD INSTALLATION DESIGNER WALL HOOD INSTALLATION Please unpack your range hood when it is delivered and inspect to ensure all parts are PARTS SUPPLIED 1. Main Hood with All Lights and 5. Flexible Duct (for 6” or 8”) Button Banks Pre-Installed 6. Packet of Screws and Anchors 2. Chimney 7. Top Mounting Bracket 3. Transition Piece (for 6” or 8”) 8. Crown Molding Bracket 4. Baffle Filters 9. Crown Molding E Height Max 36” included. 10.
DESIGNER WALL HOOD INSTALLATION The recommended height to install your hood is 30˝ minimum and 36˝ maximum DESIGNER WALL HOOD INSTALLATION 5. Make your electrical and ducting connections. Try and minimize the use of above the cooktop. For Outdoor (304 Series) hood installation, the unit must be elbows. More elbows and longer runs create higher static pressure. The hood installed at a minimum of 36˝ and a maximum of 42” above the grill.
DESIGNER WALL HOOD INSTALLATION 8. WALL CROWNSOUND® INSTALLATION Find the center of the wall where you are installing the hood. Make sure there ELECTRIC POWER RATING is sufficient bracing to hold the weight of the hood. Mark your center line and Frequency: 110V/50 Hz measure out from the center to find your two mounting points. Make sure your Power: 10W mounting points are level when you mark them. It is recommended to install the Watch Now hood directly into wood supports. Figure 7 9.
WALL CROWNSOUND® INSTALLATION 3. ISLAND HOOD INSTALLATION Extend the chimney up to the transformer. Slide the crown molding onto the crown bracket and secure into place. The crown should cover the gap. Ensure Height 26” - max 39” that it installs properly and is level. Figure 3 4. 30”-36” Figure 3 Open the phone’s Bluetooth settings and find “ZLINE Audio.“ When the connection is successful, a chime will sound. Figure 4 16 Figure 4 Bluetooth crown moldings carry a one year parts warranty.
ISLAND HOOD INSTALLATION ISLAND HOOD INSTALLATION Please unpack your range hood when it is delivered and inspect to ensure all parts are The recommended height to install your hood is 30˝ minimum and 36˝ maximum included. above the cooktop. For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of 36˝ and a maximum of 42” above the grill. PARTS SUPPLIED 1. Main Hood with All Lights and 6. Packet of Screws and Anchors Button Banks Pre-Installed 7.
DESIGNER ISLAND HOOD INSTALLATION ISLAND HOOD INSTALLATION 1. Slide chimney pieces over the angle iron on the hood. Pull the electrical plug to the top of the chimney sections. Figure 4 2. Lift the hood to attach the angle iron to the ceiling bracket. Use screws provided to attach. 3. Make your electrical and ducting connections. Use rigid ducting wherever Max 36” possible. Try and minimize the use of elbows. More elbows and longer runs create higher static pressure.
DESIGNER ISLAND HOOD INSTALLATION DESIGNER ISLAND HOOD INSTALLATION Please unpack your range hood when it is delivered and inspect to ensure all parts are The recommended height to install your hood is 30˝ minimum and 36˝ maximum included. above the cooktop. For Outdoor (304 Series) hood installation, the unit must be installed at a minimum of 36˝ and a maximum of 42” above the grill. PARTS SUPPLIED 1. Main Hood with All Lights and 6. Packet of Screws and Anchors Button Banks Pre-Installed 7.
DESIGNER ISLAND HOOD INSTALLATION 6. 7. ISLAND CROWNSOUND® INSTALLATION Slide chimney pieces over the angle iron on the hood. Pull the electrical plug to ELECTRIC POWER RATING the top of the chimney sections. Figure 4 Frequency: 110V/50 Hz Lift the hood to attach the angle iron to the ceiling bracket. Use screws provided Power: 10W to attach. 8. Watch Now Make your electrical and ducting connections. Use rigid duct wherever possible.
ISLAND CROWNSOUND® INSTALLATION 3. UNDER CABINET INSTALLATION Extend the chimney up to the transformer. Slide the crown molding onto the crown bracket and secure into place. The crown should cover the gap. Ensure 30”-36” Height that it installs properly and is level. Figure 3 4. Figure 3 Open the phone’s Bluetooth settings and find “ZLINE Audio.“ When the connection is successful, a chime will sound.
UNDER CABINET INSTALLATION UNDER CABINET INSTALLATION Undercabinet UndercabinetRecirculating RecirculatingKit Kit PREPARATION RECIRCULATING KIT • Decide the location of the venting pipe from the hood to the outside. 1. • Check hood for clearance. Step 1: 1:Open package, locate all neccessary hardware. Included Step Open package, locate all neccessary hardware. Included should be Open package, locate all necessary hardware. Included shouldshould be 4 be screws 4 screws withwith 4 washers.
UNDER CABINET INSTALLATION INSERT INSTALLATION If you need to convert your under cabinet range hood to rear ducting, use the following instructions. Please note that converting the undercab to rear ducting is a modification of the standard hood and part of the installation process. It is recommended that the hood is inspected before this procedure. Only certain undercab models allow for rear ducting. Contact us at 1-614-7775004 for more information on compatible models. 1.
REMOTE BLOWER INSTALLATION INSERT INSTALLATION When installing a range hood insert, it is recommended to install the unit at a When installing your new remote blower type range hood, follow the instructions for minimum of 30˝ from the cooktop. For outdoor range hood inserts it is recommended the type of hood you are installing. Remote blowers are available with wall, island, to install the unit at a minimum of 36˝ and a maximum of 42” from the grill top. under cabinet, and insert range hoods.
Button Control Panel Operational Manual REMOTE BLOWER INSTALLATION ! OPERATION ! ! Unit Connection Cord The Remote Blower is designed for our Remote Range Hoods. This unit is installed remotely in the interior of your home. This provides venting, but with reduced noise. T85 Remote Blower—Single Motor (This Blower must be used with Remote Blower Hood) Airflow: 400 (CFM) Remote Blower Installation Dimensions: 26.14 x 14.
CHANGING PARTS CHANGING PARTS HOW TO CHANGE OUT THE BUTTON PANEL HOW TO REPLACE THE CIRCUIT BOARD 1. Remove baffle/aluminum filters. 1. Turn the power off at the breaker and unplug the Range Hood. 2. Locate back of button panel. 2. Remove all screws from the top of the circuit board cover. 3. Remove screws from each side of the button panel. 3. Take a picture of the wiring layout (this will help you put the circuit board back 4. Disconnect button panel from cord connecting to circuit board.
CHANGING PARTS CHANGING PARTS REPLACING THE LIGHT BULBS IN YOUR RANGE HOOD PROFESSIONAL SERIES BAFFLE FILTER CHANGE 1. Remove baffles. Covering Models 696, 697, 697i (Island), KECOM, KECOMi (Island), 695, 698, 2. Squeeze the old LED light casting out until it falls out of the socket. and 721 Inserts 3. Disconnect the plug wires from the light wire. Professional series hoods are equipped with 2 removable dishwasher safe baffle 4. Reconnect the LED plug into the light wire.
CHANGING PARTS CHANGING PARTS BAFFLE FILTER CHANGE/REPLACE CAPACITOR: The baffle filter is equipped with a knob. To remove from the hood, pull back toward 1. Remove screws from the circuit board cover. the wall and down. 2. Remove screws from compactor. 3. Remove both wired connections from the capacitor. 4. Connect new capacitor with wire connectors. 5. Replace screws in cover. 6. Repeat operation if dual motor. Release NOTE: Some units have more than one motor.
CHANGING PARTS CHANGING PARTS REPLACE OR CHANGE CHARCOAL FILTERS: HOW TO CLEAN, INSTALL, OR REPLACE THE GREASE CUP: It is recommended to direct vent the hood whenever possible. A removable grease cup is provided to catch any excess grease at the bottom of the If your situation does not allow for a direct vent install, carbon filters are available to motor. Remove it every 2 to 3 months, wash it, then re-install it. recirculate the air through your hood.
CHANGING PARTS CHANGING PARTS REPLACE OR CHANGE TRANSFORMER: 1. Remove the screws from the transformer. 2. Remove the two connections to the lights. 3. Remove the two wired connections from the circuit board (you must remove the SINGLE MOTOR ELECTRICAL DIAGRAM circuit board cover). 4. Install the new connections from your new transformer (be certain the correct wires are connected). 5. Reinstall the cover for the circuit board with screws. 6. Replace all screws in the transformer. 7.
TROUBLESHOOTING CHANGING PARTS DUAL MOTOR ELECTRICAL DIAGRAM Where are ZLINE products manufactured? All ZLINE products are manufactured in ZLINE facilities overseas, including: Germany, Italy, and China. Are ZLINE range hoods considered type 1 or type 2? Type 1 - Range hoods that are used with appliances that produce grease and smoke. Are ZLINE products meant for residential or commercial use? Residential use.
TROUBLESHOOTING TROUBLESHOOTING How loud is the range hood? What type of motor is in the range hoods? A sone is measure of loudness, the higher the sone rating, the louder the sound of the Our hoods have a squirrel cage motor. hood. The sound of one sone is comparable to that of a quiet refrigerator. Keep in mind that other factors such as the size of the blowers can affect the loudness of the Is the width of my range hoods description, the actual size? range hood.
TROUBLESHOOTING TROUBLESHOOTING My hood is operating, but the air is moving slower than normal. My range hood will not operate. Check the filter for buildup and clean or replace it if needed. If the difficulty still 1. persists, check for obstructions in the ductwork. A common obstruction is buildup in the roof or wall cap, such as: bird nests or other debris. Check that there is power to the range hood. The most common issue is that the circuit breaker is off or the fuse has blown. 2.
TROUBLESHOOTING TROUBLESHOOTING My range hood is not pulling.
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C C B D D A A B A B C D 432-30 19 116 " 20 1116 " 29 3 4 " 8" 432-36 19 116 " 26 1116 " 35 3 4 " 8" 432-42 19 116 " 32 1116 " 41 3 4 " 8" 432-48 19 116 " 38 1116 " 47 3 4 " 8" Model Numbers A B C D 433-30 19 116 " 20 1116 " 29 3 4 " 8" 433-36 19 116 " 26 1116 " 35 3 4 " 8" 433-42 19 116 " 32 1116 " 41 3 4 " 8" 433-48 19 116 " 38 1116 " 47 3 4 " 8" 432 Model Numbers 433 54 55
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B C D B A B C D 435-30 19 116 " 20 1116 " 29 3 4 " 8" 435-36 19 116 " 26 1116 " 35 3 4 " 8" 436-30 19 116 " 20 1116 " 29 3 4 " 8" 436-36 19 116 " 26 1116 " 35 3 4 " 8" Model Numbers A B C D 455-30 17 1116 " 9 1116 " 13 5 16 " 6" 455-36 17 1116 " 9 1116 " 13 5 16 " 8" 455-42 17 1116 " 9 1116 " 13 5 16 " 8" 455-48 17 1116 " 9 1116 " 13 5 16 " 8" 436 Model Numbers A A D 455 56 57
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B B D D A A C A B C D 476-30 17 1116 " 9 1116 " 13 5 16 " 6" 476-36 17 1116 " 9 1116 " 13 5 16 " 8" 476-42 17 1116 " 9 1116 " 13 5 16 " 8" 476-48 17 1116 " 9 1116 " 13 5 16 " 8" Model Numbers A B C D 477-30 17 1116 " 9 1116 " 13 5 16 " 6" 477-36 17 1116 " 9 1116 " 13 5 16 " 8" 477-42 17 1116 " 9 1116 " 13 5 16 " 8" 477-48 17 1116 " 9 1116 " 13 5 16 " 8" 476 Model Numbers 477 58 59
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B D C B A A D A B C D 488-30 19 116 " 20 1116 " 29 3 4 " 8" 488-36 19 116 " 26 1116 " 35 3 4 " 8" 488-42 19 116 " 32 1116 " 41 3 4 " 8" 488-48 19 116 " 38 1116 " 47 3 4 " 8" Model Numbers A B C D 587-R-30 15 3 16 " 9 9 16 " 11 1116 " 8" 587-R-36 15 3 16 " 9 9 16 " 11 1116 " 8" 587-R-42 15 3 16 " 9 9 16 " 11 1116 " 8" 587-R-48 15 3 16 " 9 9 16 " 11 1116 " 8" 488 Model Numbers 587-R 60 61
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C C B D D A A B A B C D 587-30 15 3 16 " 9 9 16 " 11 1116 " 6" 587-36 15 3 16 " 9 9 16 " 11 1116 " 6" 587-42 15 3 16 " 9 9 16 " 11 1116 " 6" 587-48 15 3 16 " 9 9 16 " 11 1116 " 6" Model Numbers A B C D 597-R-30 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R-36 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R-42 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R-48 15 3 16 " 9 9 16 " 11 1116 " 8" 597-R-54 15 3 16 " 9 9 16 " 11 1116
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B C D B A A D A B C D 597-30 15 3 16 " 9 9 16 " 11 1116 " 6" 597-36 15 3 16 " 9 9 16 " 11 1116 " 6" 597-42 15 3 16 " 9 9 16 " 11 1116 " 6" 597-48 15 3 16 " 9 9 16 " 11 1116 " 6" 597-54 15 3 16 " 9 9 16 " 11 1116 " 6" 597-60 15 3 16 " 9 9 16 " 11 1116 " 6" Model Numbers A B C D 655-R-30 17 1116 " 9 1116 " 13 5 16 " 8" 655-R-36 17 1116 " 9 1116 " 13 5 16 " 8" 597 Model Numbers
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS B D D A C B A C A B C D Model Numbers A B C D 655-30 17 1116 " 9 1116 " 13 5 16 " 6" 667-30 17 1116 " 9 1116 " 13 5 16 " 6" 655-36 17 1116 " 9 1116 " 13 5 16 " 8" 667-36 17 1116 " 9 1116 " 13 5 16 " 8" 655-42 17 1116 " 9 1116 " 13 5 16 " 8" 667-42 17 1116 " 9 1116 " 13 5 16 " 8" 655-48 17 1116 " 9 1116 " 13 5 16 " 8" 667-48 17 1116 " 9 1116 " 13 5 16 " 8" 667-54 17 1116 " 9 1116 " 13 5 16 " 8" 667
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B B D D Model Numbers A B 685-30 19 116 " 20 1116 " 29 3 4" 8" 685-36 19 116 " 26 1116 " 35 3 4" 8" 685-42 19 116 " 32 1116 " 41 3 4 " 8" 685-48 19 116 " 38 1116 " 47 3 8" C D Model Numbers A B C D 686-30 19 116 " 20 1116 " 29 3 4 " 8" 686-36 19 116 " 26 1116 " 35 3 4 " 8" 686-42 19 116 " 32 1116 " 41 3 4 " 8" 686-48 19 116 " 38 1116 " 47 3 4 " 8" 685 4" A A C 686 68 69
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B C D B Model Numbers A 687-R-36 19 5 687-R-42 19 5 687-R-48 19 5 C D 16 " 14 14 " 17 7 8" 8" 16 " 14 14 " 17 7 8" 8" 16 " 14 14 " 17 7 8" 8" 16 " 14 14 " 17 7 8" 8" Model Numbers A B C D 687-30 19 5 16 " 14 14 " 17 7 8 " 8" 687-36 19 5 16 " 14 14 " 17 7 8 " 8" 687-42 19 5 16 " 14 14 " 17 7 8 " 8" 687-48 19 5 16 " 14 14 " 17 7 8 " 8" 687-R 687-R-30 19 5 B A A D 687 70 71
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C C B B D A A D A B C D 696-36 14 18 " 7 1116 " 11 14 " 6" 696-R-36 14 18 " 7 1116 " 11 14 " 8" Model Numbers A B C D 697-R-30 17 1116 " 9 1116 " 13 5 16 " 8" 697-R-36 17 1116 " 9 1116 " 13 5 16 " 8" 697-R-42 17 1116 " 9 1116 " 13 5 16 " 8" 697-R-48 17 1116 " 9 1116 " 13 5 16 " 8" 696 & 696-R Model Numbers 697-R 72 73
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B D C B A A D Model Numbers A B C D 697-30 17 1116 " 9 1116 " 13 5 16 " 6" 697-36 17 1116 " 9 1116 " 13 5 16 " 697-42 17 1116 " 9 1116 " 697-48 17 1116 " 697-54 697-60 Model Numbers B C D 8632-30 27 7 8 " 9 12 " 11 13 16 " 6" 8" 8632-36 27 7 8 " 9 12 " 11 13 16 " 8" 13 5 16 " 8" 8632-42 27 7 8 " 15 1116 " 18 " 8" 9 1116 " 13 5 16 " 8" 8632-48 27 7 8 " 15 1116 " 18 " 8" 17 1116 " 9 1116 " 13 5 16 " 8
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C C B B D A A D Model Numbers Model Numbers A B C D 8656-30 17 1116 " 9 1116 " 13 5 16 " 6" 8" 8656-36 17 1116 " 9 1116 " 13 5 16 " 8" 13 5 16 " 8" 8656-42 17 1116 " 9 1116 " 13 5 16 " 8" 13 5 16 " 8" 8656-48 17 1116 " 9 1116 " 13 5 16 " 8" B C D 8654-30 17 116 " 9 58 " 13 5 16 " 6" 8654-36 17 116 " 9 58 " 13 5 16 " 8654-42 17 116 " 9 58 " 8654-48 17 116 " 9 58 " 8654 A 8656
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B D C B A A D A B C D 9597-30 15 3 16 " 9 9 16 " 11 1116 " 6" 9597-36 15 3 16 " 9 9 16 " 11 1116 " 6" Model Numbers A B C D 9667-30 17 1116 " 9 1116 " 13 5 16 " 6" 9667-36 17 1116 " 9 1116 " 13 5 16 " 8" 9597 Model Numbers 9667 78 79
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B D C B A A D A B C D 9697-30 17 1116 " 9 1116 " 13 5 16 " 6" 9697-36 17 1116 " 9 1116 " 13 5 16 " 8" Model Numbers A B C D ART2-30 15 3 16 " 9 7 16 " 11 1116 " 6" ART2-36 15 3 16 " 9 7 16 " 11 1116 " 6" 9697 Model Numbers ART2 80 81
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B D C B A A D A B C D BS655N-30 17 1116 " 9 1116 " 13 5 16 " 6" BS655N-36 17 1116 " 9 1116 " 13 5 16 " 8" BS655N-42 17 1116 " 9 1116 " 13 5 16 " 8" BS655N-48 17 1116 " 9 1116 " 13 5 16 " 8" Model Numbers A B C D BSKBN-24 11 3 4 " 7 116 " 9 18 " 6" BSKBN-30 11 3 4 " 7 116 " 9 18 " 6" BSKBN-36 11 3 4 " 7 116 " 9 18 " 6" BSKBN-42 11 3 4 " 7 116 " 9 18 " 6" BSKBN-48 11 3 4 " 7 116 " 9 18 " 6" BS655N Mo
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C C B B D A A D A B C D Model Numbers A B C D BSKEN-30 12 3 4 " 9 9 16 " 11 5 8 " 6" KB-24 11 3 4 " 7 116 " 9 18 " 6" BSKEN-36 12 3 4 " 9 9 16 " 11 5 8 " 6" KB-30 11 3 4 " 7 116 " 9 18 " 6" BSKEN-42 12 3 4 " 9 9 16 " 11 5 8 " 6" KB-36 11 3 4 " 7 116 " 9 18 " 6" BSKEN-48 12 3 4 " 9 9 16 " 11 5 8 " 6" KB-42 11 3 4 " 7 116 " 9 18 " 6" KB-48 11 3 4 " 7 116 " 9 18 " 6" BSKEN Model Numbers KB 84 85
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C C B D A A B D A B C D KB2-30 13 3 8 " 7 116 " 9 18 " 6" KB2-36 13 3 8 " 7 116 " 9 18 " 6" KB2-42 13 3 8 " 7 116 " 9 18 " 6" KB2-48 13 3 8 " 7 116 " 9 18 " 6" Model Numbers A B C D KE-30 12 3 4 " 9 9 16 " 11 5 8 " 6" KE-36 12 3 4 " 9 9 16 " 11 5 8 " 6" KE-42 12 3 4 " 9 9 16 " 11 5 8 " 6" KE-48 12 3 4 " 9 9 16 " 11 5 8 " 6" KB2 Model Numbers KE 86 87
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C B C D B A A D A B C D Model Numbers A B C D KF-36 12 " 7 116 " 9 18 " 6" KL2-30 11 7 16 " 7 116 " 9 18 " 6" KF1-30 13 5 8 " 8 12 " 10 12 " 6" KL2-36 11 7 16 " 7 116 " 9 18 " 6" KF1-36 13 5 8 " 8 12 " 10 12 " 6" KL2-42 11 7 16 " 7 116 " 9 18 " 6" KF2-30 159 16 " 8 12 " 10 12 " 6" KL2-48 11 7 16 " 7 116 " 9 18 " 6" KF2-36 159 16 " 8 12 " 10 12 " 6" KF, KF1, & KF2 Model Numbers KL2 88 89
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C C B B D A A D A B C D KL3-30 12 3 4 " 7 116 " 9 18 " 6" KL3-36 12 3 4 " 7 116 " 9 18 " 6" KL3-42 12 3 4 " 7 116 " 9 18 " 6" KL3-48 12 3 4 " 7 116 " 9 18 " 6" Model Numbers A B C D KN-30 12 3 4 " 9 9 16 " 11 5 8 " 6" KN-36 13 7 16 " 9 9 16 " 11 5 8 " 6" KL3 Model Numbers KN 90 91
MOUNTING SPECIFICATIONS MOUNTING SPECIFICATIONS C C B D A A B D A B C D Model Numbers A B C D KN6-30 12 7 8 " 9 9 16 " 11 5 8 " 6" KZ-30 12 7 16 " 9 9 16 " 11 5 8 " 6" KN6-36 13 9 16 " 9 9 16 " 11 5 8 " 6" KZ-36 13 5 16 " 9 9 16 " 11 5 8 " 6" KN6 Model Numbers KZ 92 93
CMBI-655i 1314 " 93 8 " 41116 " 41116 " 8116 " 45 16 " 9116 " 33 4 " 1818 " 45 16 " CMBI-8 9116 " 8116 " 45 16 " 45 16 " CMBI-655i 33 4 " 45 16 " 85 8 " 107 8 " 8116 " 45 16 " 45 16 " 41116 " 1014 " 85 8 " 95 16 " 415 16 " 33 4 " 45 16 " 1014 " 85 8 " 93 8 " 45 16 " 43 8 " 415 16 " 41116 " 45 16 " 415 16 " 97 8 " 119 16 " CMBI-6 CMBI-655i 94 45 16 " CMBI-6 & CMBI-8 33 4 " 45 16 " 43 8 " 415 16 " MOUNTING SPECIFICATIONS 117 16 " 1314 " 93 8 " 41116 " 203 16 " CMB
Installation Guide and User Manual 1.2.1 www.zlinekitchen.
