P ressure B alance S hower S ystems Installation Guide and Users Manual
Sourced with materials from across the world, ZLINE’s shower systems are easy to operate, reduce water waste, and complement bathroom décor. This exclusive collection blends modern technology with traditional appeal — offering a wide array of finishes. ZLINE showers offer an aerated water flow for resource conservation, helping both the environment and your wallet. The housing material composition consists largely of brass, which is extremely durable and leak proof.
TABLE OF CONTENTS SAFETY INSTRUCTIONS 1 Prior to Installation Safety Tips Care and Maintenance BLISS SHOWER SYSTEM (BLS-SHS) 2 Parts Dimensions Tools Assembly EL DORADO SHOWER SYSTEM (ELD-SHS) 22 Parts Dimensions Tools Assembly SHOWER FAUCET 42 Parts Tools Assembly TROUBLESHOOTING 47
Safety Instructions Prior to Installation Make sure that the cold and hot water lines are turned off. Wrap all threaded connections with Teflon tape. Always wrap in a clockwise direction. Cover your drain to avoid losing parts. Do not disassemble the main system body, as it has been installed and commissioned correctly and precisely before delivery to the factory. To keep the system from jamming, flush the water pipe before installation. Operating conditions: Working pressure at 0.05-1.
Bliss Shower System (BLS-SHS) 1. 2. 3. 4. 5. 6. 7. 8. 2 Flange cover Shower arm Top spray shower Wall valve body Faceplate Sleeve Washer Steering handle 9. Switch handle 10. Cap 11. Sleeve 12. Flange cover 13. Angle valve 14. Shower rail 15. Shower handle 16.
Bliss Shower System (BLS-SHS) 3
Bliss Shower System (BLS-SHS) Tools: Time required: Wrench Screwdriver +/- 120 minutes Drill Legend: 4 Hot Water Cold Water Warning Plumber’s Tape Torch
Bliss Shower System (BLS-SHS) Slide the sleeves onto the pipes and then insert pipes into the wall valve. Tighten the ring around the pipes with the wrench. NOTE: If welding is involved, you must remove the internal valve components prior to the welding. Please note the original position of the cartridge.
Bliss Shower System (BLS-SHS) Weld the copper together or use plumber’s tape to prevent leaks.
Bliss Shower System (BLS-SHS) After welding, purge the water supply system for 30 seconds.
Bliss Shower System (BLS-SHS) Reinstall the valve components into their original positions.
Bliss Shower System (BLS-SHS) Use this diagram to understand the placement of the wall valve.
Bliss Shower System (BLS-SHS) Screw the wall valve body into the system with a screwdriver. Do not overtighten.
Bliss Shower System (BLS-SHS) Screw the sleeve and washer into the wall valve body.
Bliss Shower System (BLS-SHS) Attach the face plate and remove the plastic.
Bliss Shower System (BLS-SHS) Attach the steering handle.
Bliss Shower System (BLS-SHS) Connect the flange cover to the spout in the wall. Secure with plumber’s tape to prevent leaks.
Bliss Shower System (BLS-SHS) Twist the top spray shower into the shower arm.
Bliss Shower System (BLS-SHS) Connect the angle valve to the flange cover and screw together. Secure with plumber’s tape to prevent leaks.
Bliss Shower System (BLS-SHS) Use a pencil to mark the mounting holes on the wall. Use a wrench to put the screws in.
Bliss Shower System (BLS-SHS) Connect the components of the shower rail.
Bliss Shower System (BLS-SHS) Screw the shower rail into the wall.
Bliss Shower System (BLS-SHS) Connect the shower handle to the shower rail. Tighten with a wrench.
Bliss Shower System (BLS-SHS) Review the diagram to understand the hot, cold, and open settings.
El Dorado Shower System (ELD-SHS) 1. 2. 3. 4. 5. 6. 7. 8. 22 Flange cover Shower arm Top spray shower Wall valve body Faceplate Sleeve Washer Steering handle 9. Switch handle 10. Cap 11. Sleeve 12. Flange cover 13. Angle valve 14. Shower rail 15. Shower handle 16.
ۜ El Dorado Shower System (ELD-SHS) ζੋ҉स ࢺ ܜ ۜ ࢺ ܜ ELD-SHS-CH && 1010 PP ,Q PP ,Q PP ,Q PP ,Q PP ,Q PP ,Q 0$; PP ,Q 0,1 PP ,Q PP ,Q PP ,Q PP ,Q ы ༉ৃޚ؟ ҉ ஆ ఐ γޚ ༉ৃޚ؟ ҉ ஆ ఐ ၕ৸ச ܰঅ၄ ͑ ұ $ ᄥ Α ै ಌ ۢ Ӧ ส PP ۢ ᅹ -LDQ *DQJ -XO ഃ ᄍ ၗ 23
El Dorado Shower System (ELD-SHS) Tools: Time required: Wrench Screwdriver +/- 120 minutes Drill Legend: 24 Hot Water Cold Water Warning Plumber’s Tape Torch
El Dorado Shower System (ELD-SHS) Slide the sleeves onto the pipes and then insert pipes into the wall valve. Tighten the ring around the pipes with the wrench.
El Dorado Shower System (ELD-SHS) Weld the copper together or use plumber’s tape to prevent leaks.
El Dorado Shower System (ELD-SHS) After welding, purge the water supply system for 30 seconds.
El Dorado Shower System (ELD-SHS) Reinstall the valve components into their original positions.
El Dorado Shower System (ELD-SHS) Screw the wall valve body into the system with a screwdriver. Do not overtighten.
El Dorado Shower System (ELD-SHS) Place the components in the appropriate location.
El Dorado Shower System (ELD-SHS) Screw the sleeve and washer into the wall valve body.
El Dorado Shower System (ELD-SHS) Attach the face plate and remove the plastic.
El Dorado Shower System (ELD-SHS) Attach the steering handle.
El Dorado Shower System (ELD-SHS) Connect the flange cover to the spout in the wall. Secure with plumber’s tape to prevent leaks.
El Dorado Shower System (ELD-SHS) Twist the top spray shower into the shower arm.
El Dorado Shower System (ELD-SHS) Connect the angle valve to the flange cover and screw together. Secure with plumber’s tape to prevent leaks.
El Dorado Shower System (ELD-SHS) Use a pencil to mark the mounting holes on the wall. Use a wrench to put the screws in.
El Dorado Shower System (ELD-SHS) Connect the components of the shower rail.
El Dorado Shower System (ELD-SHS) Screw the shower rail into the wall.
El Dorado Shower System (ELD-SHS) Connect the shower handle to the shower rail. Tighten with a wrench.
El Dorado Shower System (ELD-SHS) Review the diagram to understand the hot, cold, and open settings.
SHOWER FAUCET 1. 2. 3. 4. 5. 6. 7.
SHOWER FAUCET Tools: Time required: Wrench Screwdriver +/- 60 minutes Hacksaw and tape measure Legend: Hot Water Cold Water Warning Plumber’s Tape Grease 43
SHOWER FAUCET Mark on the wall where you want the Use a screwdriver to screw the faucet faucet to be installed. onto the wall. Attach the hose using plumbing tape and a wrench. 44 Place the components in the appropriate location.
SHOWER FAUCET Screw the sleeve and washer into the wall valve body. Make sure that the components are aligned properly. Tighten the components. Take off the protective shield.
SHOWER FAUCET Attach faucet to base plate. Attach base plate to wall. Attach handle to the fixture. Review the diagram to understand the hot, cold, and open settings.
Troubleshooting Problem Possible Cause Solution There is leakage under the The locking nut has Unscrew the lever on the handle. come loose. handle by hand. Loosen set screw with a hex wrench. Remove the handle and unscrew trim cap by hand. Tighten locking nut with an adjustable wrench. Water will not shut off Cartridge may be Unscrew the level on the completely. defective. handle by hand. Loosen set screw with a hex wrench. Remove the handle and unscrew trim cap by hand.
Kitchen and Bath Three Locations: 350 Parr Circle Reno, NV 89512 916 Delaware Avenue Marysville, OH 43040 427 Rowland Mill Road Bruceton, TN 38317 www.zlinekitchen.com 1-614-777-5004 1.1.
