S hower S ystems Installation Guide and Users Manual
Sourced with materials from across the world, ZLINE’s shower systems are easy to operate, reduce water waste, and complement bathroom décor. This exclusive collection blends modern technology with traditional appeal — offering a wide array of finishes. ZLINE showers offer an aerated water flow for resource conservation, helping both the environment and your wallet. The housing material composition consists largely of brass, which is extremely durable and leak proof.
TABLE OF CONTENTS SAFETY INSTRUCTIONS 1 Prior to Installation Safety Tips Care and Maintenance SHOWER SYSTEM BODY 2 Parts Tools Assembly SHOWER SYSTEM FAUCET 22 Parts Tools Assembly TROUBLESHOOTING 27
Safety Instructions Prior to Installation Make sure that the cold and hot water lines are turned off. Wrap all threaded connections with Teflon tape. Always wrap in a clockwise direction. Cover your drain to avoid losing parts. Do not disassemble the main system body, as it has been installed and commissioned correctly and precisely before delivery to the factory. To keep the system from jamming, flush the water pipe before installation. Operating conditions: Working pressure at 0.05-1.
Shower System 1. 2. 3. 4. 14. 5. 6. 12. 11. 13. 7. 8. 10. 1. Flange Cover 2. Shower Arm 3. Top Spray Shower 4. Wall Valve Body 5. Faceplate 6. Sleeve 7. Washer 8. Steering Handle 2 15. 9. 9. Switch Handle 10. Cap 11. Sleeve 12. Flange Cover 13. Angle Valve 14. Shower Rail 15. Handle Shower 16. Hose 16.
Shower System Top spray shower Switch handle Shower faucet 3
SHOWER SYSTEM BODY Tools: Time required: Wrench Screwdriver +/- 120 minutes Drill Legend: 4 Hot Water Cold Water Warning Plumber’s Tape Torch
SHOWER SYSTEM BODY Slide the sleeves onto the pipes and then insert pipes into the wall valve. Tighten the ring around the pipes with the wrench.
SHOWER SYSTEM BODY Weld the copper together or use plumber’s tape to prevent leaks.
SHOWER SYSTEM BODY After welding, purge the water supply system for around 30 seconds. After welding, purge the water supply system for 30 seconds.
SHOWER SYSTEM BODY Reinstall the valve components into their original positions. Reinstall the valve components into their original positions.
SHOWER SYSTEM BODY Screw the wall valve body into the system with a screwdriver. Do not overtighten.
SHOWER SYSTEM BODY Place the components in the appropriate location.
SHOWER SYSTEM BODY Screw the sleeve and washer into the wall valve body.
SHOWER SYSTEM BODY Attach the face plate and remove the plastic.
SHOWER SYSTEM BODY Attach the steering handle.
SHOWER SYSTEM BODY Connect the flange cover to the spout in the wall. Secure with plumber’s tape to prevent leaks.
SHOWER SYSTEM BODY Twist the top spray shower into the shower arm.
SHOWER SYSTEM BODY Connect the angle valve to the flange cover and screw together. Secure with plumber’s tape to prevent leaks.
SHOWER SYSTEM BODY Use a pencil to mark the mounting holes on the wall. Use a wrench to put the screws in.
SHOWER SYSTEM BODY Connect the components of the shower rail.
SHOWER SYSTEM BODY Screw the shower rail into the wall.
SHOWER SYSTEM BODY Connect the shower handle to the shower rail. Tighten with a wrench.
SHOWER SYSTEM BODY Review the diagram to understand the hot, cold, and open settings.
SHOWER SYSTEM FAUCET 1. 2. 3. 7. 6. 1. Rough-in 2. Sleeve 3. Faceplate 4. Cap 5. Handle 6. Spout 7. Screw 22 4. 5.
SHOWER SYSTEM FAUCET Tools: Time required: Wrench +/- 60 minutes Screwdriver Hacksaw and tape measure Legend: Hot Water Cold Water Warning Plumber’s Tape Grease 23
SHOWER SYSTEM FAUCET Mark on the wall where you want the Use a screwdriver to screw the faucet faucet to be installed. onto the wall. Attach the hose using plumbing tape and a wrench. 24 Place the components in the appropriate location.
SHOWER SYSTEM FAUCET Screw the sleeve and washer into the wall valve body. Make sure that the components are aligned properly. Tighten the components. Take off the protective shield.
SHOWER SYSTEM FAUCET Attach faucet to base plate. Attach base plate to wall. Attach handle to the fixture. Review the diagram to understand the hot, cold, and open settings.
Troubleshooting Problem Possible Cause Solution There is leakage under the The locking nut has Unscrew the lever on the handle. come loose. handle by hand. Loosen set screw with a hex wrench. Remove the handle and unscrew trim cap by hand. Tighten locking nut with an adjustable wrench. Water will not shut off Cartridge may be Unscrew the level on the completely. defective. handle by hand. Loosen set screw with a hex wrench. Remove the handle and unscrew trim cap by hand.
Kitchen and Bath Three Locations: 350 Parr Circle Reno, NV 89512 916 Delaware Avenue Marysville, OH 43040 319 Rowland Mill Road Bruceton, TN 38317 www.zlinekitchen.
