Installation Guide

For a complete list of applicable patent(s) or pending patent(s), visit www.zircon.com/trademarks-patents/
1580 Dell Avenue
|
Campbell, CA 95008
|
[e-mail]
T: 1.408.963.4550
|
F: 1.408.963.4597
|
zircon.com
Stud Finder
Dimensions 7.1 in. x 3.2 in. x 1.8 in. (181 mm x 81 mm x 45 mm )
Weight
6.4 oz. (180g) (no battery)
Battery Type
9V alkaline battery required, not included
Position Accuracy
Up to a depth of ¾ in. (19 mm) typically, within
1
⁄8 in. (3 mm)
Depth
Target Control
™
mode: up to ¾ in. (19 mm)
StudScan mode: up to ¾ in. (19 mm)
WireWarning
®
Position
Accuracy
Typically, 120-230V at 50-60Hz within 6 in.
(150 mm) of hot unshielded wire in drywall
WireWarning
®
Depth Up to 2 in. (50 mm) deep
Operating Temperature 40° to 120°F (4° to 49°C)
Storage Temperature 20° to 140°F (-7° to 60°C)
Humidity 5-95% RH (non-condensing)
Water Resistance Splash and water resistant, not waterproof
*NOTE: USE ONLY IN ACCORDANCE WITH SUPERSCAN
TM
M1 INSTRUCTIONS.
See tool’s instructions for more information. Sensing depth and accuracy can vary due to
moisture, content of materials, wall texture, paint, etc. Indoor use only.
© 2020. ACT, ColorTrip, LoLevel, SpotLite, SuperScan, Target Control, TC, WireWarning, and Zircon are all trademarks or registered trademarks of Zircon Corporation • GF-4248 Rev A 11/20
Specifications
WireWarning
®
Detection
LoLevel
™
/Signal Strength
Indicator
Stud Center Finding
SuperScan
™
M1
|
Advanced Stud Finder
Target Control
™
Technology
Featuring new, revolutionary Target Control
™
(TC
™
) Level 1 Technology. The Zircon
®
SuperScan
™
M1 advanced
stud finder is tuned to find clean, wood studs while filtering out metallic false positive objects, such as
plumbing, conduit, straps, brackets, or ducts, hidden behind surfaces. The LoLevel
™
Indicator signals to the
presence of dangerous, deep, and less dense false positive targets, reducing the chance of accidentally drilling
into objects such as plastic pipes.
The SuperScan
™
M1 offers two distinct detection modes - TC
™
and StudScan. The ColorTrip
®
Display
conveniently details information. The screen will illuminate blue in TC
™
mode and indicate the center, edges,
and direction of wood studs while also enabling the user to identify ‘safe-to-drill’ zones by utilizing the new
‘Trust but Verify’ technique. When TC
™
mode is off, the tool will perform in StudScan mode indicating the
center, edges, and direction of both wood and metal studs. The Target Spotlight illuminates on screen and the
SpotLite
®
Pointer shines on the surface being scanned when the center of a stud is found.
• NEW! – Target Control
™
(TC
™
) Mode locates the center, edges, and direction of wood studs, and not
metal, up to ¾ in. (19 mm) deep. Identifies ‘safe-to-drill’ zones between adjacent drywall screws,
nails, or protector plates
• StudScan Mode locates center, edges, and direction of wood and metal studs up to ¾ in. (19 mm) deep
• WireWarning
®
Detection continuously alerts to the presence of live, unshielded AC wires up to
2 in. (50 mm) deep
• LoLevel
™
Indicator displays low (weak) signal objects, such as plastic water pipes, while in TC
™
mode
• Signal Strength Indicator helps distinguish between shallow and deep targets while in StudScan mode
• ACT
™
(Auto Correcting Technology) automatically cor rects common errors, such as when scanning begins
over a stud
• Target Spotlight illuminates on screen when stud center is detected
• ColorTrip
®
Display illuminates blue in TC
™
mode
• SpotLite
®
Pointer shines an arrow-shaped light on the scanned surface to indicate the center of a stud
• “V” marker groove enables accurate marking of stud location
• Low Battery Indicator for optimum performance (9V battery required, not included)