ZP19064 ASSEMBLY INSTRUCTIONS BELLA PUPPY AND GARDEN FENCE KIT 2-PACK 2-PACK ASSEMBLY INSTRUCTIONS ZP19064 (41” W X 30” H) 60 MIN Approximate assembly time Want to see a video on how to assemble this product? Scan the QR code WWW.ZIPPITY-OUTDOOR.COM 1 VER.
ZP19064 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT k Check the inside of the larger pieces in your box for other materials packed inside. k When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. k We recommend an area approximately 5’x 8’ for unobstructed assembling. k You should not need to use excessive force when assembling components.
ZP19064 ASSEMBLY INSTRUCTIONS 41 in 1 1/8 in 30 in 26 1/2 in 2 in 12 in WWW.ZIPPITY-OUTDOOR.
ZP19064 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A B E Picket (18) 3/8” x 2¾” x 27” Post Cap (4) D C Post (4) ⅞” x 1½” x 42” F Joiner Clip (4) G Bottom Rail (2) 1½” x 1½” x 40 ⅞” 4 Top Rail (2) 1½” x 1½” x 40 ⅞” ¾" Self-Drilling Stainless Steel Screw (24) WWW.ZIPPITY-OUTDOOR.
ZP19064 ASSEMBLY INSTRUCTIONS STEP 2: ASSEMBLE THE FENCE FRAME STEP 2.1 Lay out (1) Bottom Rail (C) and (1) Top Rail (D). D The top rail has picket holes on both sides. C STEP 2.2 E 1 1. Insert (2) Posts (E) down into the holes in the rails as shown. 2. Continue sliding the posts until the predrilled holes in the posts and the rails align. 3. Drive (8) total ¾” Self-Drilling Stainless Steel Screws (G) into the holes in the rails. 2 Align WWW.ZIPPITY-OUTDOOR.
ZP19064 ASSEMBLY INSTRUCTIONS STEP 3: INSTALL THE PICKETS STEP 3.1 Insert (9) Pickets (B), into the rails until the picket tabs lock into the bottom rail. B Note: It may take some light force to insert the pickets through the routed holes. STEP 4: ASSEMBLE THE SECOND PANEL STEP 4.1 Repeat Steps 2 and 3 to assemble the second fence panel. 6 WWW.ZIPPITY-OUTDOOR.
ZP19064 ASSEMBLY INSTRUCTIONS STEP 5: INSTALL THE FENCE STEP 5.1 Push down on the top of the posts with both hands. Move the panel to its final location, and identify where the posts will be located. Attempt to push the unit into the ground as illustrated. STEP 5.2 1. If your ground is too hard, loosen the top 6” or 7” of the ground with a claw hammer as illustrated. 2. Add water to the loosened soil. 3. Use a block of wood to protect the top of the post, and gently hammer the post into the ground.
ZP19064 ASSEMBLY INSTRUCTIONS STEP 5.4 Optional in hard ground: If your ground is too hard, or you have more than 3 or 4 panels to install, please consider these options: 1. Use a 1¾” diameter auger bit (commonly used for planting tulips) as illustrated ($15-$20 on Amazon.com). 2. Drill a hole about 12” to 16” deep at the desired location, and fill the holes with water as illustrated. 3. Push the fence posts into the holes. 1 2 3 8 WWW.ZIPPITY-OUTDOOR.
ZP19064 ASSEMBLY INSTRUCTIONS STEP 5.5 Optional: If your ground is very hard, you may need to dig a single hole large enough to accommodate one post from each panel. This hole should be approximately 8” in diameter and 16” deep. 8” diameter x 16” deep. STEP 5.6 Level the panel as necessary, backfill excavated dirt, and tamp down. Level WWW.ZIPPITY-OUTDOOR.
ZP19064 ASSEMBLY INSTRUCTIONS STEP 6: CONNECT THE PANELS STEP 6.1 1. Straight Line Application: Fasten the panels together with (2) Joiner Clips (F) using (4) ¾” self-drilling stainless steel screws. 2. Corner Application: Fasten the panels together with (2) Joiner Clips (F) using (4) ¾” self-drilling stainless steel screws. 1 F F 2 10 WWW.ZIPPITY-OUTDOOR.
ASSEMBLY INSTRUCTIONS ZP19064 STEP 7: INSTALL POST CAPS STEP 7.1 Push the Post Caps (A) down over the posts to lock them into place. A WWW.ZIPPITY-OUTDOOR.
ZP19064 ASSEMBLY INSTRUCTIONS 6935 Reames Rd. Ste. K. Charlotte, NC 28216 support@zippity-outdoor.com 704-892-5222 877-234-6196 WWW.ZIPPITY-OUTDOOR.COM 12 WWW.ZIPPITY-OUTDOOR.
