Operation Manual

78
IMPORTANT: The devices cannot operate without
loading. Each time before staring the device, ll it up
with product.
Put the corns into the pan (VIII), set up the handle of the
body (III) on the thicker grinding, set up the machine engine.
The grinded product will start pouring out through the hole.
Regulate the quern regulator (II), depending of the demanded
grinding level or using seeds, with the handle of the body for
obtain the product with the adequate granulation level.
By turning it clockwise you will get the ne grind product.
By turning it counter-clockwise – the thick grind product.
The nest (minimal) grinding level is achieved by setting it
up with the handle on the line 1, and the hugest (maximal)
by setting it up with the handle on the STOP line. See the
graphic on the body (III) and quern regulator (II).
Too strong twisting or turning of the handle out of STOP
line during the work time can cause the device failure.
CAUTION: It` s recommended to set the quern
regulator during the grinder work time between the
line 1 and STOP line.
IMPORTANT: It`s FORBIDDEN to use the REVERSE
function in the machine when the grinder is installed.
CAUTION: Remember about the accurate washing the
grinder before grinding of the different products. It will
permit to avoid the mutual penetration of odors.
CAUTION: For the soft corns as oat or linseed it`s
necessary to select the coast-grained set up.
ATTENTION! Do not look into the grinding chamber
during operation, as the beans which pop out
sometimes, can hurt you (i.e. your eye).
Cleaning and maintenance
The grinder does not requires the cleaning after each
operation (if it`s grinded one kind of product), cause the
worm prevents falling the seeds residues into grinder. Dry
the steel quern (4, 5) using a soft cloth after cleaning to
prevent corrosion. In case of long-term storage, conserve
the quern by greasing them (you can use edible oil). Do
not immerse the quern into boiling water. The part of plastic
(don`t containing the graphic) can be washed in the dish-
washer (max. of 60°C).
After operation (Fig. 11)
Switch off and unplug the appliance.
●
Remove the pusher and take out the tray from the mincer
●
body, the shredder body or the juicer body (in case of the
citrus juicer separately remove the squeezer and screen).
Press the lock button
●
(1), turn (2) the mincing unit, the
shredder body (or the citrus juicer bowl) to the right and
remove it.
In case of the citrus juicer take out the clutch from the
●
motor.
The manufacturer does not accept any liability for any damages
resulting from unintended use or inappropriate handling.
The manufacturer reserves his rights for modifying the product any
time in order to adjust it to law regulations, norms, directives, or due
to construction, trade aesthetic or other reasons, without notifying it
in advance.
Dismantle the elements of the mincing unit, the body with
●
the sausage ller nozzle, the juicer body or the shredder.
Store the clean and dry screens in the compartment. In
●
order to do so:
Open the compartment on the back of the housing. ●
Press the compartment lock on both sides and pull ●
(as shown earlier).
(3) ● Store up to two screens and close the compartment
and the back lid (4).
(5)
●
Put away the cord, pushing it gently through the
opening.
(6)
●
Place the plug in the compartment.
Cleaning and maintenance
Wipe the motor with a damp cloth with dishwashing
●
liquid.
Wash plastic elements in warm soapy water or in the
●
dishwasher according to the denotations.
Wash metal elements in hot soapy water.
●
Dry all elements thoroughly.
●
Grease the screens and cutter with cooking oil to protect
●
from rusting.
Assemble dry elements of the mincer body or the
●
shredder.
Ecology – Environment protection
Each user can protect the natural environment.
It is neither difcult nor expensive.
In order to do it: put the cardboard packing into
recycling paper container; put the polyethylene
(PE) bags into container for plastic.
When worn out, dispose the appliance to particular disposal
centre, because of the dangerous elements of this appliance,
which can be hazardous for natural environment.
Do not dispose into the domestic waste disposal!!!