Product Label

ManualsBrandsZAR ManualsInterior Wood Stains1 qt. Semi-Transparent 120 Premium Teak Oil-Based Multi-Surface Interior Wood Stain

SURFACE PREPARATION: Substrates should be clean and

free from dirt, wax, and grease.

1. Fill holes and cracks with ZAR

Wood Patch.

2. Sand smooth with 120-150 grit sandpaper.

3. Remove sanding dust and wipe clean with a tack cloth

or cloth dampened with paint thinner or mineral spirits.

Allow to dry.

APPLICATION ON BARE WOOD: Stir thoroughly before

and during application. Using a lint-free cloth (like a

t-shirt) or brush apply ZAR

Stain evenly in the direction

of the grain and wipe off excess in the same direction.

For a darker tone, re-stain when the ﬁrst coat is dry. For a

lighter tone, wipe the surface with a cloth dampened with

mineral spirits or paint thinner before the stain has dried.

DRYING: Allow 3 hours drying time before applying ZAR

Water Base or Oil Base Poly.

CLEAN UP: Application tools and excess stain can be

cleaned up with paint thinner or mineral spirits.

COVERAGE: Approximately 800 (74 m

) sq. ft. per

quart. Note: Actual coverage will vary depending upon

application method, surface texture, and porosity.

THINNING: DO NOT THIN.

APPLICATION ON PAINTED AND PRE-FINISHED

CABINETS: DO NOT SAND PAINTED SURFACE. Surfaces

must be clean and free from dirt, wax, and grease. Painted

surfaces must be thoroughly dry. Apply ZAR

Stain with

a clean, lint-free cloth (like a t-shirt) or brush. Apply to

desired areas to achieve a glazed two-tone effect. Wipe

off excess or dry brush the stain depending on the desired

look. For pre-ﬁnished cabinets, sand the surface lightly

with 320 grit sandpaper. Remove sanding dust and wipe

clean with a tack cloth or cloth dampened with paint

thinner or mineral spirits. Allow to dry. Apply stain with a

clean, lint-free cloth (like a t-shirt) in the direction of the

grain. Dry brush the stain to feather out corners and lap

marks. Let the stain dry 48 hours and apply ZAR

Water

Base or Oil Base Poly for the ultimate protection.

APPLICATION ON FIBERGLASS, METAL, AND COMPOSITE

SURFACES: DO NOT SAND BARE EMBOSSED SURFACE.

Apply using a clean, lint-free cloth (like a t-shirt) in a circular

motion (like you apply shoe polish), working the stain into

the embossed grain pattern. Next, use your stain cloth to

smooth the stain in the direction of the embossed grain

pattern. Use a dry soft bristle brush to feather out lap marks.

Allow to dry thoroughly.

DRYING: Allow non-wood surfaces to dry 48 hours, for

ultimate protection topcoat with ZAR

Water Base or Oil

Base Poly.

APPLICATION ON GLAZING OPEN GRAINED WOODS:

This process creates a two-tone effect and is easy to do! It

works best with opened grain woods such as oak.

1. Apply ZAR

Stain according to directions or leave unstained.

2. Apply one coat of ZAR

Water Base or Oil Base Poly over

the stained or bare wood surface and let dry according to

label instructions.

3. Apply a contrasting ZAR

Stain color wiping across the

grain. Immediately wipe off the excess stain and let dry

for 24-48 hours depending on temperature and humidity.

For ultimate protection topcoat with ZAR

Water Base or

Oil Base Poly.

MIXING AND TINTING:

Personalize and create a unique color by intermixing any

ZAR

Stain colors together for unlimited color possibilities.

Check out our intermixing formula color guide using a 1:1

ratio formula.

WARNING! If you scrape, sand, or remove old paint, you may

release lead dust. LEAD IS TOXIC. EXPOSURE TO LEAD DUST

CAN CAUSE SERIOUS ILLNESS, SUCH AS BRAIN DAMAGE,

ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD

ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator

to control lead exposure. Clean up carefully with a HEPA vacuum

and a wet mop. Before you start, ﬁnd out how to protect yourself

and your family by contacting the National Lead Information

Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

CAUTION: CONTAINS PETROLEUM DISTILLATE. VAPOR HARMFUL. MAY AFFECT THE

BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE, OR NAUSEA. CAUSES EYE, SKIN,

NOSE, AND THROAT IRRITATION.

NOTICE: Reports have associated repeated and prolonged occupational overexposure

to solvents with permanent brain and nervous system damage. Intentional misuse by

deliberately concentrating and inhaling the contents may be harmful or fatal.

Keep away from heat and flame. Prevent build-up of vapors by opening all windows and

doors to achieve cross-ventilation.

Use only with adequate ventilation. Do not breathe vapors. Ensure fresh air entry during

application and drying. If you experience eye watering, headache, or dizziness, or if air

monitoring demonstrates vapor/mist levels are above applicable limits, wear an appropriate,

properly fitted respirator (NIOSH-approved) during and after application. Follow respirator

manufacturer’s directions for respirator use. Avoid contact with eyes, skin, and clothing. Wash

thoroughly after handling.

First Aid: In case of eye contact, flush immediately with plenty of water for at least 15 minutes

and call poison control center, hospital emergency room, or physician immediately; for skin,

wash thoroughly with soap and water. If you experience difficulty in breathing, leave the area

to obtain fresh air. If continued difficulty is experienced, call poison control center, hospital

emergency room, or physician immediately. If swallowed, do not induce vomiting. Call poison

control center, hospital emergency room, or physician immediately.

KEEP OUT OF REACH OF CHILDREN.

If spilled, contain spilled material and remove with

inert absorbent. Dispose of contaminated absorbent,

container, and unused contents in accordance with

local, state, and federal regulations.

DANGER – RAGS, STEEL WOOL, OR WASTE

SOAKED WITH PRODUCT MAY SPONTANEOUSLY

CATCH FIRE IF IMPROPERLY DISCARDED.

IMMEDIATELY AFTER USE, PLACE RAGS, STEEL

WOOL, OR WASTE IN A SEALED, WATER-FILLED

METAL CONTAINER.

WARNING: Cancer and Reproductive

Harm – www.P65Warnings.ca.gov.

DOES NOT EXCEED MAXIMUM VOC 500 g/L

is a highly pigmented oil base stain uniquely formulated to achieve a

rich, luxurious color in one coat. Its thick viscosity allows for easy application resulting in a rich

uniform color. Use on wood, ﬁberglass, metal, painted, and pre-ﬁnished surfaces. Ideal for hard to

stain woods like pine, birch, alder, and maple. Can be used as a glaze on cabinets, moldings, and

ﬂoors to achieve a two-tone layered effect.

L119

UNITED GILSONITE LABORATORIES, 1396 Jefferson Ave., Dunmore, PA 18509

www.UGL.com

Order No. 12012

MULTI-SURFACE

Rich Luxurious Color in One Coat

800

SQ.FT.

800

SQ. FT.

1 QT (946 mL)

SEE CAUTIONS ON BACK PANEL.

DANGER!

COMBUSTIBLE LIQUID AND VAPOR.

PREMIUM TEAK

120

INTERIOR OIL BASE

R7044