Product Label

ManualsBrandsZAR ManualsInterior Wood Stains1 gal. Semi-Transparent 119 Mocha Oil-Based Multi-Surface Interior Wood Stain

LR519 www.UGL.com

UNITED GILSONITE LABORATORIES, 1396 Jefferson Ave., Dunmore, PA 18509

is a highly pigmented oil base stain uniquely formulated to achieve a rich, luxurious color in one coat. Its thick viscosity

allows for easy application resulting in a rich uniform color. Use on wood, ﬁberglass, metal, painted, and pre-ﬁnished surfaces. Ideal for hard to

stain woods like pine, birch, alder, and maple. Can be used as a glaze on cabinets, moldings, and ﬂoors to achieve a two-tone layered effect.

MULTI-SURFACE

Rich Luxurious Color in One Coat

INTERIOR OIL BASE

SURFACE PREPARATION: Substrates should be clean and free from dirt, wax, and grease.

1. Fill holes and cracks with ZAR

Wood Patch.

2. Sand smooth with 120-150 grit sandpaper.

3. Remove sanding dust and wipe clean with a tack cloth or cloth dampened with paint

thinner or mineral spirits. Allow to dry.

APPLICATION ON BARE WOOD: Stir thoroughly before and during application. Using a

lint-free cloth (like a t-shirt) or brush apply ZAR

Stain evenly in the direction of the grain

and wipe off excess in the same direction. For a darker tone, re-stain when the ﬁrst coat is

dry. For a lighter tone, wipe the surface with a cloth dampened with mineral spirits or paint

thinner before the stain has dried.

DRYING: Allow 3 hours drying time before applying ZAR

Water Base or Oil Base Polyurethane.

CLEAN UP: Application tools and excess stain can be cleaned up with paint thinner or

mineral spirits.

COVERAGE: Approximately 3200 sq. ft. (296 m

) per gallon. Note: Actual coverage will vary

depending upon application method, surface texture, and porosity.

THINNING: DO NOT THIN.

APPLICATION ON PAINTED AND PRE-FINISHED CABINETS: DO NOT SAND PAINTED

SURFACE. Surfaces must be clean and free from dirt, wax, and grease. Painted surfaces

must be thoroughly dry. Apply ZAR

Stain with a clean, lint-free cloth (like a t-shirt) or

brush. Apply to desired areas to achieve a glazed two-tone effect. Wipe off excess or dry

brush the stain depending on the desired look. For pre-ﬁnished cabinets, sand the surface

lightly with 320 grit sandpaper. Remove sanding dust and wipe clean with a tack cloth or

cloth dampened with paint thinner or mineral spirits. Allow to dry. Apply stain with a clean,

lint-free cloth (like a t-shirt) in the direction of the grain. Dry brush the stain to feather out

corners and lap marks. Let the stain dry 48 hours and apply ZAR

Water Base or Oil Base

Polyurethane for the ultimate protection.

APPLICATION ON INTERIOR/EXTERIOR FIBERGLASS, METAL, AND COMPOSITE SURFACES:

DO NOT SAND BARE EMBOSSED SURFACE. Apply using a clean, lint-free cloth (like a t-shirt)

in a circular motion (like you apply shoe polish), working the stain into the embossed grain

pattern. Next, use your stain cloth to smooth the stain in the direction of the embossed

grain pattern. Use a dry soft bristle brush to feather out lap marks. Allow to dry thoroughly.

DRYING: Allow non-wood surfaces to dry 48 hours, for ultimate protection topcoat with

ZAR

Water Base or Oil Base Polyurethane.

APPLICATION ON GLAZING OPEN GRAINED WOODS: This process creates a two-tone

effect and is easy to do! It works best with opened grain woods such as oak.

1. Apply ZAR

Stain according to directions or leave unstained.

2. Apply one coat of ZAR

Water Base or Oil Base Polyurethane over the stained or bare

wood surface and let dry according to label instructions.

3. Apply a contrasting ZAR

Stain color wiping across the grain. Immediately wipe off

the excess stain and let dry for 24-48 hours depending on temperature and humidity. For

ultimate protection topcoat with ZAR

Water Base or Oil Base Polyurethane.

MIXING AND TINTING: Personalize and create a unique color by intermixing any ZAR

Stain colors together for unlimited color possibilities. Check out our intermixing formula

color guide using a 1:1 ratio formula.

WARNING! If you scrape, sand, or remove old paint, you may release lead dust.

LEAD IS TOXIC. EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS ILLNESS,

SUCH AS BRAIN DAMAGE, ESPECIALLY IN CHILDREN. PREGNANT WOMEN

SHOULD ALSO AVOID EXPOSURE. Wear a NIOSH-approved respirator to control

lead exposure. Clean up carefully with a HEPA vacuum and a wet mop. Before you

start, ﬁnd out how to protect yourself and your family by contacting the National

Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.

CAUTION: CONTAINS PETROLEUM DISTILLATE. VAPOR HARMFUL. MAY AFFECT THE

BRAIN OR NERVOUS SYSTEM CAUSING DIZZINESS, HEADACHE, OR NAUSEA. CAUSES

EYE, SKIN, NOSE, AND THROAT IRRITATION.

NOTICE: Reports have associated repeated and prolonged occupational overexposure

to solvents with permanent brain and nervous system damage. Intentional misuse by

deliberately concentrating and inhaling the contents may be harmful or fatal.

Keep away from heat and flame. Prevent build-up of vapors by opening all windows

and doors to achieve cross-ventilation.

Use only with adequate ventilation. Do not breathe vapors. Ensure fresh air entry

during application and drying. If you experience eye watering, headache, or dizziness,

or if air monitoring demonstrates vapor/mist levels are above applicable limits, wear an

appropriate, properly fitted respirator (NIOSH-approved) during and after application.

Follow respirator manufacturer’s directions for respirator use. Avoid contact with eyes,

skin, and clothing. Wash thoroughly after handling.

First Aid: In case of eye contact, flush immediately with plenty of water for at least

15 minutes and call poison control center, hospital emergency room, or physician

immediately; for skin, wash thoroughly with soap and water. If you experience difficulty

in breathing, leave the area to obtain fresh air. If continued difficulty is experienced,

call poison control center, hospital emergency room, or physician immediately. If

swallowed, do not induce vomiting. Call poison control center, hospital emergency room,

or physician immediately.

KEEP OUT OF REACH OF CHILDREN.

If spilled, contain spilled material and remove with inert absorbent. Dispose

of contaminated absorbent, container, and

unused contents in accordance with local,

state, and federal regulations.

DANGER – RAGS, STEEL WOOL, OR

WASTE SOAKED WITH PRODUCT MAY

SPONTANEOUSLY CATCH FIRE IF IMPROPERLY

DISCARDED. IMMEDIATELY AFTER USE, PLACE

RAGS, STEEL WOOL, OR WASTE IN A SEALED,

WATER-FILLED METAL CONTAINER.

WARNING: Cancer and Reproductive

Harm – www.P65Warnings.ca.gov.

DOES NOT EXCEED MAXIMUM VOC 500 g/L

MOCHA

119

800

SQ.FT.

3200

SQ. FT.

1 GALLON (3,785 L)

SEE CAUTIONS ON BACK PANEL.

DANGER!

COMBUSTIBLE LIQUID AND VAPOR.

Order No. 11913

R8308

Summary of content (1 pages)

PAGE 1
is a highly pigmented oil base stain uniquely formulated to achieve a rich, luxurious color in one coat. Its thick viscosity allows for easy application resulting in a rich uniform color. Use on wood, fiberglass, metal, painted, and pre-finished surfaces. Ideal for hard to stain woods like pine, birch, alder, and maple. Can be used as a glaze on cabinets, moldings, and floors to achieve a two-tone layered effect. INTERIOR OIL BASE MULTI-SURFACE SEE CAUTIONS ON BACK PANEL. COV 3200 800 SQ. FT. SQ.FT.