User Manual GETTING STARTED? EASY.
SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
• • • • • • • • • – areas for communal use in blocks of flats or in launderettes. Do not exceed the maximum load of 7 kg (refer to the "Programme chart" chapter). The operating water pressure at the water entry point from the outlet connection must be between 0.5 bar (0.05 MPa) and 8 bar (0.8 MPa). The ventilation opening in the base must not be covered by a carpet, mat, or any floor covering.
ELECTRICAL CONNECTION USE WARNING! Risk of injury, electric shock, fire, burns or damage to the appliance. WARNING! Risk of fire and electric shock. • • • • • • • • • The appliance must be earthed. Always use a correctly installed shockproof socket. Make sure that the parameters on the rating plate are compatible with the electrical ratings of the mains power supply. Do not use multi-plug adapters and extension cables. Make sure not to cause damage to the mains plug and to the mains cable.
PRODUCT DESCRIPTION APPLIANCE OVERVIEW 1 2 3 4 5 6 1 Detergent dispenser 2 Control panel • 3 Door handle 4 Rating plate 5 Drain pump filter 6 Feet for levelling the appliance CHILD SAFETY This device prevents children or pets to be closed in the drum. • Turn the device clockwise, until the groove is horizontal. You cannot close the door. To close the door, turn the device anticlockwise until the groove is vertical.
CONTROL PANEL CONTROL PANEL DESCRIPTION 1 2 10 1 Programme knob 2 Display 3 Delay Start button (Delay Start) 9 8 6 4 5 8 Prewash button (Prewash) 9 Options button (Option) 4 Door locked indicator 5 Start/Pause button (Start/Pause) 7 3 • ECO (Eco) • Quick (Quick Wash) 10 Spin reduction steps (Spin) 6 Extra Rinse button (Extra Rinse) • Rinse Hold position (Rinse Hold) 7 Easy Iron button (Easy Iron) DISPLAY A • B The display shows the following information: A - Child lock indicator:
PROGRAMMES PROGRAMME CHART Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Cottons 90°C - 60°C - 40°C 30°C 7 kg 1200 rpm White cotton and coloured cotton. Normal, heavy and light soil. Cottons 7 kg 1200 rpm White cotton and fast-coloured cotton. Normal soil. The energy consumption decreases and the time of the washing programme is extended, ensuring good washing results.
Programme Temperature range Maximum load Maximum spin speed Programme description (Type of load and soil level) Drain 7 kg To drain the water after programme with the option Rinse Hold selected. Spin 7 kg 1200 rpm To spin and drain the water after programme with the option Rinse Hold selected Set the spin speed according to the fabric to be spun. For cancelling the programme which is running or switch the appliance off.
Programme 1) 2) 3) 4) ■ ■ 1) This option is not active at a temperature lower than 40°C. 2) If you select this option we recommend that you reduce the maximum load. full loading is possible, however with somewhat reduced cleaning results. 3) If using liquid detergent, a programme without prewash must be selected. 4) if you set the Easy Iron, the recommended max load is 1.5 kg. CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant standards.
OPTIONS PROGRAMME SELECTION This knob allows you to select a programme and/or to switch the appliance on/off . SPIN With this option you can change the default spin speed. The indicator of the set speed comes on. RINSE HOLD • Set this option to prevent the laundry creases. • The related indicator comes on. • There is a water in the drum when the programme is completed. • The drum turns regularly to prevent the laundry creases. • The door stays locked. You must drain the water to unlock the door.
If you deactivate the acoustic signals, they continue to operate when the appliance has a malfunction. BEFORE FIRST USE 1. Connect the mains plug to the mains socket. 2. Open the water tap. 3. Put 2 litre of water in the detergent compartment for washing phase. This activates the drain system. 4. Put a small quantity of detergent in the compartment for washing phase. 5. Set and start a programme for cotton at the highest temperature without laundry.
STARTING A PROGRAMME WITH THE DELAY START OPTION 1. Press the button Delay Start again and again until the display shows the delay you want to set. The delay start indicator comes on. 2. Press the button Start/Pause: • • • The door is locked and the indicator is on. The appliance starts the countdown. When the countdown is completed, the programme starts automatically. You can cancel or change the set of the Delay Start option before you press the button Start/Pause.
Draining the water: 1. To drain the water. • Set a Drain or a Spin programme. • Press the button Start/Pause. The appliance drains the water and spins. 2. When the programme is completed and the door lock indicator the door. goes off, you can open 3. Turn the programme knob to the position deactivate the appliance. to STAND BY Some minutes after the end of the washing programme, if you do not deactivate the appliance, the energy saving status activates.
CARE AND CLEANING • WARNING! Refer to Safety chapters. • EXTERNAL CLEANING Clean the appliance with soap and warm water only. Fully dry all the surfaces. CAUTION! Do not use alcohol, solvents or chemical products. DESCALING If the water hardness in your area is high or moderate, we recommend that you use a water descaling product for washing machines. Regularly examine the drum to prevent limescale and rust particles. To remove rust particles use only special products for washing machines.
A B • • • • • • 1 • 2 • • • Place a container close to the pump (A) to collect any spillage. Pull out the emergency emptying hose (B), place it in the container and remove its cap. When no more water comes out, unscrew the filter. Turn the filter anticlockwise. Remove the filter. Use pliers, if necessary. When removing the filter, always keep a rag nearby to dry up any water spillage. Clean the filter under a tap, to remove any traces of fluff.
FROST PRECAUTIONS If the appliance is installed in an area where the temperature can be less than 0° C, remove the remaining water from the inlet hose and the drain pump. 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3. Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water flow out of the hoses. 4. Set the Drain programme and let it operate until the end of the cycle. 5.
Problem The appliance does not fill with water properly. Possible solution • • • The appliance does not drain the water. • • • • • • Make sure that the water tap is open. Make sure that the pressure of the water supply is not too low. For this information, contact your local water authority. Make sure that the water tap is not clogged. Make sure that the sink spigot is not clogged. Make sure that the drain hose has no kinks or bends. Make sure that the drain filter is not clogged.
INSTALLATION WARNING! Refer to Safety chapters. • Remove the polystyrene block fitted on the door seal. Pull out all items from the drum. • Fill the smaller upper hole and the two large ones with the plastic plug caps supplied in the bag with the User Manual. UNPACKING Remove all transit bolts and packing before you use the appliance. You are advised to keep all transit devices so t hat they can be refitted if the appliance ever has to be transported again.
WATER INLET • The inlet hose is supplied with the appliance and can been found inside the appliance drum. • Do not use the hose from your previous appliance to connect to the water supply. This appliance must be connected toa cold water supply. • • • Connect the hose with the angled connection to the machine. Do not place the inlet hose downwards. 45˚ • Angle the hose to the left or right depending 35˚ on the position of your water tap. Set the hose correctly by loosening the ring nut.
BUILDING IN OVERVIEW This appliance has been designed to be built into the kitchen furniture. The recess should have the dimensions shown in the picture below: Door • - width 595-598 mm • - thickness 16-22 mm The height X depends on the height of the adjacent furniture's base. 600 mm 16-22 mm min. 596 mm 560 mm 555 mm min.
The hinges can be adjusted to compensate for possible uneven thickness of the door. If the door has to be opened from left to right, invert the position of the plates E, the magnet D and the plate C. Mount the counter-magnet D and the hinges A as previously described. Do not remove the screw B! A D B A C To align the door perfectly, loosen the screw, adjust the door and tighten the screw A again. The appliance is prearranged for a magnetic closure of the door.
Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture IPX4 Water supply pressure 0,5 bar (0,05 MPa) 8 bar (0,8 MPa) Minimum Maximum Cold water Water supply 1) Maximum Load Cotton 7 kg Energy Efficiency Class Spin Speed A Maximum 1200 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. ENVIRONMENTAL CONCERNS with the symbol with the household waste.
132928496-A-242018 WWW.ZANUSSI.
