INSTRUCTION BOOKLET COOKER HOOD ZHC590
Thank you for buying a Zanussi product. To enable you to use your appliance effectively and safely, please read this instruction book carefully before using the appliance and retain for future reference. If you require guidance in the use of the appliance or require further information on Zanussi Products, please contact our Customer Care Department. For general enquiries concerning your Zanussi appliance or for further information, visit our website at http://www.zanussi.co.
IMPORTANT SAFETY INFORMATION These warnings are provided in the interests of your safety. Ensure that you understand them all before installing or using this appliance. Your safety is of paramount importance. If you are unsure about any of the meanings of these warnings contact the Customer Care Department. Installation Child Safety • Any installation work must be undertaken by a qualified electrician or a competent person. • This appliance is designed to be operated by adults.
YOUR APPLIANCE 5
OPERATING INSTRUCTIONS The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. The appliance can be installed to recirculate or extract contaminated air. Control Panel The hood can be switched on pushing directly onto the requested speed without firstly having to select 0/1 button. KEY LED L 0/1 Light T1 0/1 Motor FUNCTIONS Turns lighting on and off. on First speed. When pressed for about 1 seconds the motor is switched off.
OPERATING INSTRUCTIONS To Operate Select the required fan speed and light if required. Recirculation In the recirculation mode the contaminated air enters the cooker hood through the grease filters. The air is cleaned by passing through the charcoal filters before being passed back into the kitchen through the grilles in either side of the chimney stack.
MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean, as a build up of grease or fat can be a fire hazard. External Cleaning Wipe the cooker hood frequently with warm soapy water using a mild detergent. Never use scouring pads or abrasive cleaners. Never use excessive amounts of water when cleaning particularly around the control panel.
MAINTENANCE AND CLEANING Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. Charcoal Filters In the recirculation mode the charcoal filters absorb smells and unwanted odours. Enabling the alarm signal • • • • • • In Recirculation version Hoods, the Filter saturation alarm can be enabled on installation or at a later date. Turn the Lights and the suction Motor off. Disconnect the Hood using the Main switch or the double-pole switch on the mains power supply.
SOMETHING NOT WORKING If, having followed these instructions carefully, your cooker hood fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start • Check the hood is connected to the electricity supply. • Make sure the switch is in the ‘ON’ position. The cooker hood is not working effectively • The fan speed is set high enough for the task • The grease filter is clean. • The kitchen is adequately vented to allow the entry of fresh air.
GUARANTEE CONDITIONS We Zanussi, undertake that if within twenty four months of the date of the purchase this Zanussi built-in appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our option repair or replace the same FREE OF ANY CHARGE for labour, materials or carriage on condition that: • • • • • The appliance has been correctly installed and used only on the electrical supply stated on the rating plate.
INSTALLATION INSTRUCTIONS It is dangerous to alter the specifications or attempt to modify this product in any way.
INSTALLING THE COOKER HOOD Please ensure that when the appliance is installed it is easily accessible to an engineer in the event of a breakdown. All installations must comply with the local authorities requirements for the discharge of exhaust air. Incorrect installation may affect the safety of this cooker hood. Installation Requirements Before installation check the wall to which the cooker hood is to be fitted for electric cables, water pipes or gas.
INSTALLING THE COOKER HOOD Clearance Height The cooker hood is designed to be fitted over a cooking appliance at the clearance heights stated, providing the maximum output of the appliance beneath does not exceed the maximums quoted in the Technical Specifications. If the output of the appliance below the cooker hood exceeds the maximum outputs quoted, please refer to the cooker manufacturer’s installation instructions.
INSTALLING THE COOKER HOOD Drilling the Ceiling/Support Shelf • Use a plumb line to mark the centre of the hob on the ceiling/support shelf. • Place the drilling template 21 provided on the ceiling/ support shelf, making sure that the template is in the correct position by lining up the axes of the template with those of the hob. • Mark the centres of the holes in the template. • Drill the holes at the points marked: • For concrete ceilings, drill for plugs appropriate to the screw size.
INSTALLING THE COOKER HOOD • Lift the frame up, making sure that the index over the frame plate is turned backwards. • Fit the frame slots onto the two screws inserted in the ceiling as above, and turn until reaching the centre of the adjustment slot. • Tighten the two screws and fasten the other two screws provided; before locking the screws completely, it is possible to adjust the frame by turning it, making sure that the screws do not come out of their housing in the adjustment slot.
INSTALLING THE COOKER HOOD Ducting Connection Connect the ducting chosen to: • the Ø150mm ducting spigot on top of the motor housing, or the Ø150-120mm ducting spigot item 9 and secure using the jubilee clips item 25. 9 + 9a • A Ø120-125mm collar item 9a is provided to fit over the Ø120mm ducting spigot when 125mm ducting is fitted.
INSTALLING THE COOKER HOOD Chimney Stack The chimney consists of two sections. The lower chimney measures (with the Hood body and recirculation grilles) 935 mm and the upper chimney measures 290 mm. The overall installed measurement is min. 935 - max 1215 mm. Fitting the Upper Chimney and the Hood Body • Position the upper chimney stack and fix the top of it to the frame using 2 of the screws removed as above.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
