User manual Dishwasher ZDTL 200
Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances. Please read this user manual carefully and keep it throughout the product life cycle as a reference document. The user manual should be passed on to any future owner of the appliance.
Safety information In the interest of your safety and to ensure the correct use, before installing and first using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features.
Installation • Check your dishwasher for any transport damage. Never connect a damaged machine. If your dishwasher is damaged contact your supplier. • All packaging must be removed before use. • Any electrical and plumbing work required to install this appliance must be carried out by a qualified and competent person. • For safety reasons it is dangerous to alter the specifications or attempt to modify this product in any way.
Setting mode The appliance is in setting mode when all programme lights are off and End of programme light flashes. IMPORTANT! Always remember that when performing operations such as: • selecting a washing programme • setting the water softener • deactivation/activation of the audible signals Delay start button the appliance MUST be in setting mode. If a programme light is illuminated and End of programme light is illuminated with fixed light, the last performed programme is still set.
Programme selection/cancel button • Starting the washing programme: 1. Press the On-Off button. 2. Press the Programme selection/cancel button once, the light of the last performed washing programme illuminates and the End of programme light flashes. 3. Press the Programme selection/cancel button as many times as necessary to illuminate the light corresponding to the desired programme. 4. Close the dishwasher’s door, the programme will start automatically.
Indicator lights Salt Illuminates when the special salt has run out. Is never illuminated while a washing programme is running. Audible signals Audible signals have been introduced to help indicate which operations the dishwasher is performing. – end of the washing programme, – malfunction of the appliance Factory setting: audible signals activated. It is possible to deactivate the audible signals, using the Programme selection/Cancel button. Deactivation/activation of the audible signals 1.
Programme Normal 65° Degree of soil Type of load Programme description Normal soil Crockery, cutlery, pots and pans Prewash Main wash 2 intermediate rinses Final rinse Drying Light soil Crockery and cutlery Main wash Final rinse BIO 50° 2) Normal soil Crockery and cutlery Prewash Main wash 1 intermediate rinse Final rinse Drying Rinse and Hold Any. Partial load (to be completed later in the day). 65° A 30'1) 1 cold rinse (to avoid food scraps from sticking together).
IMPORTANT! If the drying results are not satisfactory we recommend that you: 1. Fill up the rinse aid dispenser with rinse aid. 2. Set the rinse aid dosage to position 2. If you decide in future to use separated detergents, we advise that you: – Fill up the salt and rinse aid container. – Adjust the water hardness setting to the highest level and perform 1 normal washing programme without loading any dishes. – Adjust the water hardness setting according to the hardness of the water in your area.
Setting the water softener manually (see table) The water softener is factory set at position 2. Set switch to position 1 or 2 Setting the water softener electronically (see table) 1. Press the On/Off button. The appliance must be in setting mode. 2. Press and hold Programme selection/ Cancel button until programme light A flashes and programme light B illuminates with fixed light. 3.
Unscrew the cap. Only before filling with Using the funnel provided, salt for the first time, fill pour in the salt until the the salt container with wa- container is filled with salt. ter. IMPORTANT! Immediately start a complete programme. IMPORTANT! Water will overflow from the container as salt is added. Remove any trace of salt. Replace the cap tightly turning it clockwise until it stops with a click. IMPORTANT! Top up the special salt when the light on the control panel illuminates.
Use of rinse aid Open the lid. Fill up with rinse aid. The Clean up any rinse aid maximum level for filling is which overflows. Close the lid and press until it indicated by "max" locks. IMPORTANT! CAUTION! Top up the rinse aid when the light on the control panel Never fill the rinse aid dispenser with any other subilluminates. stances (e.g. dishwasher cleaning agent, liquid detergent). This would damage the appliance.
• Before loading the dishes, you should: – Remove all left over food and debris. – Soften remnants of burnt food in pans • When loading the dishes and cutlery, please note: – Dishes and cutlery must not impede the rotation of the spray arms. – Load hollow items such as cups, glasses, pans, etc. with the opening downwards so that water cannot collect in the container or a deep base. – Dishes and items of cutlery must not lie inside one another, or cover each other.
Load cutlery. For best results we recommend you to use the cutlery grid provided (if the size and dimensions of the cutlery allow it) Place knives and other items of cutlery with sharp points or edges with their handles facing upwards. Risk of injury! Load the lower basket. Arrange serving dishes and large lids around the edge of the basket. Load upper basket. Light items (plastic bowls etc.) must be loaded in the upper basket and arranged so they do not move.
Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position. Maximum height of the dishes in : upper basket lower basket With upper basket raised 22 cm 33 cm With upper basket lowered 26 cm 29 cm To move to the higher position proceed as follows: 1. Pull out the basket until it stops. 2. Carefully lift both sides upwards until the mechanism is engaged and the basket is stable.
Open the lid. Fill in the detergent in compartment A. Observe the dosing levels. For programmes with pre- When using detergent Close the lid. wash add an additional tablets: place detergent detergent dose in comtablets in compartment A. partmentB. Detergent tablets Detergent tablets from different manufacturers dissolve at different rates. For this reason, some detergent tablets do not attain their full cleaning power during short washing programmes.
Care and cleaning Cleaning the filters IMPORTANT! NEVER use the dishwasher without filters. Incorrect repositioning and fitting of the filters will produce poor washing results. Clean filters A, B and C Turn the handle about 1/4 Remove filter A from the thoroughly under running turn anticlockwise and re- base of the washing commove filters B and C. water. partment. Replace the filters and lock by turning the handle clockwise to the stop.
Internal cleaning Ensure that the seals around the door, the detergent and rinse aid dispensers are cleaned regularly with a damp cloth. We recommend every 3 months to run the wash programme for heavy soiled dishes using detergent but without dishes. Prolonged periods of nonoperation If you are not using the machine for any prolonged period of time you are advised to: 1. Unplug the appliance and then turn off the water. 2. Leave the door ajar to prevent the formation of any unpleasant smells. 3.
correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product. What to do if… The dishwasher will not start or stops during operation.
Fault code and malfunction The programme does not start. Possible cause and solution • The dishwasher door has not been properly closed. Close the door. • The main plug is not plugged in. Insert the mains plug. • The fuse has blown in the household fuse box. Replace the fuse. Once these checks have been carried out; switch on the dishwasher. The programme will continue from the point at which it was interrupted. If the malfunction or fault code reappears contact the Service Force Centre.
The wash results are not satisfactory There are streaks, milky spots or a bluish coating on glasses and dishes • Decrease rinse aid dosing. Water drops have dries onto glasses and dishes • Increase rinse aid dosing. • The detergent may be the cause. Contact the detergent manufacturer’s consumer care line. If after all these checks, the problem persists, contact your local Service Force Centre.
Consumption values Programme Programme duration (in Energy consumption (in minutes) kWh) Rinse and Hold 12 0,1 Water (litres) 5 Hints for test institutes Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Consumption values").
Installation WARNING! Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. Fitting under a counter IMPORTANT! Carefully follow the instructions on the enclosed template for building in the dishwasher and fitting the furniture panel. WARNING! The dishwasher must be secured against tilting.
If the water inlet hose leaks, the safety valve cuts off the water supply. WARNING! The electrical cable for the safety valve is in the double-walled water inlet hose and is live. Therefore do not immerse the water inlet hose or the safety valve in water. Take care when installing the water inlet hose . Place the water inlet hose in such a way that it is always lower than the bottom edge of the safety valve. If the water inlet hose or the safety valve is damaged, remove the mains plug immediately.
Electrical connection CAUTION! Safety standards require the appliance to be earthed. Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on the rating plate match that of the supply where the appliance is to be installed. The fuse rating is also to be found on the rating plate. Always plug the mains plug into a correctly installed shockproof socket. Multi-way plugs, connectors and extension cables must not be used.
www.electrolux.