TABLE DE CUISSON KOOKPLATEN KOCHMULDEN HOBS INSTRUCTION BOOKLET NOTICE D'UTILISATION GEBRUIKSAANWIJZING GEBRAUCHSANLEITUNG GB BE
ENGLISH IMPORTANT SAFETY INFORMATION You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 727727 Installation ● This hob must be installed by qualified personnel, according to the manufacturer’s instructions and to the relevant British Standards. ● Remove all packaging before using the hob. ● Ensure that the electrical supply complies with the type stated on the rating plate, located on the bottom of the hob.
CONTENTS For the User For the Installer Description of the Hob Technical Data Page 9 Page 5 Operation Page 6 Important Safety Requirements Page 9 Installation Page 10 Building In Page 10 Electrical Connection Page 12 Wiring Diagram Page 13 Maintenance and Cleaning Page 7 Something Not Working? Page 7 Service and Spare Parts Page 8 Guarantee Conditions Page 8 Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instruction
DESCRIPTION OF THE HOB 3 1 2 5 4 10 1. 2. 3. 4. 5. 6. 7. 8. 9. 9. 9 8 7 6 Hob Top Rapid Hotplate - 2090 W/180 mm dia. Normal Hotplate - 1040 W/145 mm dia. Rapid Hotplate - 1570 W/145 mm dia. Normal Hotplate - 1570 W/180 mm dia. Control knob for back left hotplate Control knob for back right hotplate Control knob for front right hotplate Control knob for front left hotplate Electric Hotplates Control Light INSTALLATION The hob must be installed according to the instructions supplied.
OPERATION ELECTRIC HOTPLATES To switch on a hotplate, turn the relevant control knob anticlockwise to the required heat setting. The control knob is numbered 1 - 6 i Saucepans for use on solid plates should have several characteristics: ● 0 - OFF ● 1 - Minimum 6 - Maximum. ● The hob has two types of hotplates: Normal Hotplates We recommend the plates are switched to maximum (6) for a short while to boost the plate, and then adjusted to the required setting.
MAINTENANCE AND CLEANING Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
SERVICE AND SPARE PARTS CUSTOMER CARE If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929929 Your call will be routed to your local Service Force Centre. For further details, please see the accompanying Customer Care Booklet.
INSTRUCTIONS FOR THE INSTALLER Important safety requirements Engineer technical data This hob must be installed in accordance with the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions. OVERAll dimensions Width: Depth: Height: Weight: 580 mm. 500 mm. 88 mm. 11 Kg. Location cut out dimensions Width: 550 mm. Depth: 470 mm. Thickness: 30 mm.
INSTALLATION important Rectangular cut-out size for hob This hob must be installed by qualified personnel to the relevant British Standards. 0 58 50 The manufacturer will not accept liability, should the above instructions or any of the other safety instructions incorporated in this book be ignored. 0 Cut Out Size The dimensions of the cut-out are given in the diagram. 55 0 47 0 n.
Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be hot when in operation. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. 30 3 a 60 20 min Building over a kitchen unit with door b FO 1013 Dimensions are given in mm.
ELECTRICAL CONNECTIONS Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THIS HOB MUST BE EARTHED. The hob should be conncted to a double pole switch with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations.
WIRING DIAGRAM N Ø 145 Ø 180 Ø 145 Ø 180 4 3 2 1 4 3 2 1 4 3 2 1 4 3 2 1 1 2 3 4 P2 4 3 P1 1 2 P3 5 P2 4 3 P1 1 2 P3 5 P2 4 3 P1 1 2 P3 5 P2 4 3 P1 1 2 P3 5 PLATE L 13
