EN User Manual Dishwasher KDV10020FA
Contents Safety information Safety instructions EASY START Programmes Settings Before first use 2 3 4 5 5 8 Daily use Hints and tips Care and cleaning Troubleshooting Technical information 8 11 12 13 16 Subject to change without notice. Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage.
• • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put the cutlery in the cutlery basket with the sharp ends pointing down or put them in the cutlery drawer in a horizontal position with the sharp edges down. Do not leave the appliance with the open door unattended to avoid stepping accidentally onto it.
Warning! Dangerous voltage. • If the water inlet hose is damaged, immediately close the water tap and disconnect the mains plug from the mains socket. Contact the Authorised Service Centre to replace the water inlet hose. Service • Contact the Authorised Service Centre to repair the appliance. We recommend only the use of original spare parts. When you contact the Authorised Service Centre, ensure that you have the following information that is available on the rating plate.
Programmes Programme 2) 3) 4) Degree of soil Type of load Programme phases Consumption values 1) Duration (min) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry 225 0.789 9.5 Heavy soil Crockery, cutlery, pots and pans • • • • Prewash Wash 70 °C Rinses Dry 130 - 150 1.0 - 1.2 11 - 13 Normal soil Crockery and cutlery • • • • Prewash Wash 65 °C Rinses Dry 100 - 110 1.2 - 1.6 15 - 16 Fresh soil Crockery and cutlery • 30 0.
RESET function Press and hold simultaneously and until the appliance is in programme selection mode. With this function you can cancel the running programme or the delay start. User mode While the appliance is in programme selection mode: 1. Press and hold • The indicators and . , and flash. Settings available in the user mode: • The level of the water softener according to the water hardness. • The activation or the deactivation of the acoustic signal indicating the end of programme.
2. 3. Press to change the setting. Each pressing of the button reaching level 10, the count starts again from level 1. Press the on/off button to confirm the setting. increases the level number. After The water hardness table German degrees (°dH) French degrees (°fH) mmol/l Clarke degrees Water softener level 47 -50 84 - 90 8.4 - 9.0 58 - 63 10 43 - 46 76 - 83 7.6 - 8.3 53 - 57 9 37 - 42 65 - 75 6.5 - 7.5 46 - 52 8 29 - 36 51 - 64 5.1 - 6.4 36 - 45 7 23 - 28 40 - 50 4.0 - 5.
Before first use 1. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. 2. Fill the salt container. 3. Fill the rinse aid dispenser. 4. Open the water tap. 5. Start a programme to remove any processing residuals that can still be inside the appliance. Do not use detergent and do not load the baskets.
Adding detergent 1 A B 30 20 2 If the programme has a prewash phase, put a small quantity of detergent also in compartment B. Adding multi-tablets 1 30 20 2 • Adjust the water softener to the lowest level. Setting and starting a programme The AUTO OFF function This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the programme.
Option delay 1. Set the programme. 2. Press the button to delay the start of the programme. The 3. Close the appliance door to start the countdown. When the countdown is completed, the programme starts. indicator is on. Option XtraDry Activate this option when you want to boost the drying performance. With the use of this option, the duration of some programmes, water consumption and the last rinse temperature can be affected.
• Close the water tap. If you open the door before the activation of AUTO OFF, the appliance is automatically deactivated. Hints and tips General The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • • • • • • • • Remove larger residues of food from the dishes into the waste bin. Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase.
Before starting a programme Unloading the baskets Make sure that: 1. • • • • 2. The filters are clean and correctly installed. The cap of the salt container is tight. The spray arms are not clogged. There is dishwasher salt and rinse aid (unless you use multi- tablets). The position of the items in the baskets is correct. The programme is applicable for the type of load and for the degree of soil. The correct quantity of detergent is used.
Internal cleaning • • • Carefully clean the appliance, including the rubber gasket of the door, with a soft damp cloth. If you regularly use short duration programmes, these can leave deposits of grease and limescale inside the appliance. To prevent this, we recommend to run long duration programmes at least 2 times per month. To maintain the performance of your appliance at its best, we recommend to use monthly a specific cleaning product for dishwashers.
Problem and alarm code Possible cause and solution The program lasts too long. • If the delayed start option is set, cancel the delay setting or wait for the end of the countdown. Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten the adjustable feet (if applicable). The appliance door is not centred on the tub. Adjust the rear foot (if applicable). • The appliance door is difficult to close. • Rattling/knocking sounds from inside the appliance.
Problem The dishes are wet. Possible cause and solution • • • • • • For the best drying performance activate the option XtraDry. The programme does not have a drying phase or has a drying phase with low temperature. The rinse aid dispenser is empty. The quality of the rinse aid can be the cause. The quality of the multi-tablets can be the cause. Try a different brand or activate the rinse aid dispenser and use rinse aid and multi-tablets together.
Technical information Dimensions Width / height / depth (mm) 446 / 818 - 898 / 550 Electrical connection 1) Voltage (V) 220 - 240 Frequency (Hz) 50 Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8) Water supply Cold water or hot water 2) max 60 °C Capacity Place settings 9 Power consumption Left-on mode (W) 5.0 Power consumption Off-mode (W) 0.10 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g.
www.electrolux.