EN User Manual Dishwasher KDT10002FB
Contents Safety information Safety instructions Control panel Programmes Settings Before first use 2 3 4 5 5 7 Daily use Hints and tips Care and cleaning Troubleshooting Technical information 7 9 10 11 13 Subject to change without notice. Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages.
• • • • • • • If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or similarly qualified persons in order to avoid a hazard. Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position. Do not keep the appliance door open without supervision to prevent to fall on it. Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket.
Use • • • • • • • Do not sit or stand on the open door. Dishwasher detergents are dangerous. Obey the safety instructions on the detergent packaging. Do not drink and play with the water in the appliance. Do not remove the dishes from the appliance until the programme is completed. There can be detergent on the dishes. The appliance can release hot steam if you open the door while a programme operates.
Programmes Programme 2) 3) 4) Degree of soil Type of load Programme phases Consumption values 1) Duration (min) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry 195 1.039 11 Heavy soil Crockery, cutlery, pots and pans • • • • Prewash Wash 70 °C Rinses Dry 140 - 160 1.5 - 1.6 13 - 15 Normal soil Crockery and cutlery • • • • Prewash Wash 65 °C Rinses Dry 120 - 130 1.3 - 1.6 15 - 17 Fresh soil Crockery and cutlery • 30 0.
User mode While the appliance is in programme selection mode: 1. Press and hold programme button until the indicator starts to flash and the indicator is on. In user mode can be changed: • The level of the water softener according to the water hardness. • The activation or the deactivation of the acoustic signal for end of programme. These settings will be saved until you change them again. Reset function Press the programme button until all programme indicators are on (Programme selection mode).
2. Wait until the indicator 3. 4. Press programme button to change the setting. The indicator Press on/off button to confirm the setting. goes off. The indicator is off. The acoustic signal is off. is on. The acoustic signal is on. Before first use 1. 2. 3. 4. 5. Make sure that the current level of the water softener agrees with the hardness of the water supply. If not, adjust the level of the water softener. Fill the salt container. Fill the rinse aid dispenser. Open the water tap.
Adding detergent 1 A B 30 20 2 If the programme has a prewash phase, put a small quantity of detergent also in compartment B. Adding multi-tablets 1 30 20 2 • • • Do not fill the salt container and the rinse aid dispenser. Adjust the water softener to the lowest level. Set the rinse aid dispenser to the lowest position. Setting and starting a programme Starting a programme 1. 2. 3. 4. Keep the appliance door ajar. Press the on/off button to activate the appliance.
Hints and tips General • The following hints will ensure optimal cleaning and drying results in daily use and also help to protect the environment. • • • • • • • Remove larger residues of food from the dishes into the waste bin. Do not pre-rinse dishes by hand. When needed, use the prewash programme (if available) or select a programme with a prewash phase. Always use the whole space of the baskets.
• The correct quantity of detergent is used. 2. Unloading the baskets 1. Let the tableware cool down before you remove it from the appliance. Hot items can be easily damaged. First remove items from the lower basket, then from the upper basket. At the end of the programme water can still remain on the sides and on the door of the appliance. Care and cleaning Warning! Before maintenance, deactivate the appliance and disconnect the mains plug from the main socket.
Troubleshooting If the appliance does not start or it stops during operation, before you contact an Authorised Service Centre, check if you can solve the problem by yourself with the help of the information in the table. With some problems the end indicator flashes intermittently indicating a malfunction. The majority of problems that can occur can be solved without the need to contact an Authorised Service Centre. Warning! Repairs not properly done may result in serious risk to the safety of the user.
Problem and alarm code Possible cause and solution • The appliance trips the circuit-beaker. • The amperage is insufficient to supply simultaneously all the appliances in use. Check the socket amperage and the capacity of the meter or turn off one of the appliances in use. Internal electrical fault of the appliance. Contact an Authorised Service Centre. For alarm codes not described in the table, contact an Authorised Service Centre.
Problem Traces of rust on cutlery. Possible cause and solution • • There are residues of detergent in the dispenser at the end of the programme. • • • There is too much salt in the water used for washing. Refer to "The water softener". Silver and stainless steel cutlery were placed together. Avoid to put silver and stainless steel items close together. The detergent tablet got stuck in the dispenser and therefore was not completely washed away by water.
Rating Plate Information for test institutes For all the necessary information for test performance, send an email to: info.test@dishwasher-production.com Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... Write down the product number (PNC) that is on the rating plate. ENVIRONMENT CONCERNS not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office. Recycle the materials with the symbol .
www.electrolux.